Blame view
include/asm-parisc/superio.h
3.22 KB
1da177e4c
Linux-2.6.12-rc2
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 |
#ifndef _PARISC_SUPERIO_H
#define _PARISC_SUPERIO_H
#define IC_PIC1 0x20 /* PCI I/O address of master 8259 */
#define IC_PIC2 0xA0 /* PCI I/O address of slave */
/* Config Space Offsets to configuration and base address registers */
#define SIO_CR 0x5A /* Configuration Register */
#define SIO_ACPIBAR 0x88 /* ACPI BAR */
#define SIO_FDCBAR 0x90 /* Floppy Disk Controller BAR */
#define SIO_SP1BAR 0x94 /* Serial 1 BAR */
#define SIO_SP2BAR 0x98 /* Serial 2 BAR */
#define SIO_PPBAR 0x9C /* Parallel BAR */
#define TRIGGER_1 0x67 /* Edge/level trigger register 1 */
#define TRIGGER_2 0x68 /* Edge/level trigger register 2 */
/* Interrupt Routing Control registers */
#define CFG_IR_SER 0x69 /* Serial 1 [0:3] and Serial 2 [4:7] */
#define CFG_IR_PFD 0x6a /* Parallel [0:3] and Floppy [4:7] */
#define CFG_IR_IDE 0x6b /* IDE1 [0:3] and IDE2 [4:7] */
#define CFG_IR_INTAB 0x6c /* PCI INTA [0:3] and INT B [4:7] */
#define CFG_IR_INTCD 0x6d /* PCI INTC [0:3] and INT D [4:7] */
#define CFG_IR_PS2 0x6e /* PS/2 KBINT [0:3] and Mouse [4:7] */
#define CFG_IR_FXBUS 0x6f /* FXIRQ[0] [0:3] and FXIRQ[1] [4:7] */
#define CFG_IR_USB 0x70 /* FXIRQ[2] [0:3] and USB [4:7] */
#define CFG_IR_ACPI 0x71 /* ACPI SCI [0:3] and reserved [4:7] */
#define CFG_IR_LOW CFG_IR_SER /* Lowest interrupt routing reg */
#define CFG_IR_HIGH CFG_IR_ACPI /* Highest interrupt routing reg */
/* 8259 operational control words */
#define OCW2_EOI 0x20 /* Non-specific EOI */
#define OCW2_SEOI 0x60 /* Specific EOI */
#define OCW3_IIR 0x0A /* Read request register */
#define OCW3_ISR 0x0B /* Read service register */
#define OCW3_POLL 0x0C /* Poll the PIC for an interrupt vector */
/* Interrupt lines. Only PIC1 is used */
#define USB_IRQ 1 /* USB */
#define SP1_IRQ 3 /* Serial port 1 */
#define SP2_IRQ 4 /* Serial port 2 */
#define PAR_IRQ 5 /* Parallel port */
#define FDC_IRQ 6 /* Floppy controller */
#define IDE_IRQ 7 /* IDE (pri+sec) */
/* ACPI registers */
#define USB_REG_CR 0x1f /* USB Regulator Control Register */
#define SUPERIO_NIRQS 8
struct superio_device {
u32 fdc_base;
u32 sp1_base;
u32 sp2_base;
u32 pp_base;
u32 acpi_base;
int suckyio_irq_enabled;
struct pci_dev *lio_pdev; /* pci device for legacy IO (fn 1) */
struct pci_dev *usb_pdev; /* pci device for USB (fn 2) */
};
/*
* Does NS make a 87415 based plug in PCI card? If so, because of this
* macro we currently don't support it being plugged into a machine
* that contains a SuperIO chip AND has CONFIG_SUPERIO enabled.
*
* This could be fixed by checking to see if function 1 exists, and
* if it is SuperIO Legacy IO; but really now, is this combination
* going to EVER happen?
*/
#define SUPERIO_IDE_FN 0 /* Function number of IDE controller */
#define SUPERIO_LIO_FN 1 /* Function number of Legacy IO controller */
#define SUPERIO_USB_FN 2 /* Function number of USB controller */
#define is_superio_device(x) \
(((x)->vendor == PCI_VENDOR_ID_NS) && \
( ((x)->device == PCI_DEVICE_ID_NS_87415) \
|| ((x)->device == PCI_DEVICE_ID_NS_87560_LIO) \
|| ((x)->device == PCI_DEVICE_ID_NS_87560_USB) ) )
extern int superio_fixup_irq(struct pci_dev *pcidev); /* called by iosapic */
#endif /* _PARISC_SUPERIO_H */
|