Blame view
Documentation/gpio.txt
29.9 KB
4c20386c8 [PATCH] GPIO core |
1 2 3 |
GPIO Interfaces This provides an overview of GPIO access conventions on Linux. |
7560fa60f gpio: <linux/gpio... |
4 5 |
These calls use the gpio_* naming prefix. No other calls should use that prefix, or the related __gpio_* prefix. |
4c20386c8 [PATCH] GPIO core |
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 |
What is a GPIO? =============== A "General Purpose Input/Output" (GPIO) is a flexible software-controlled digital signal. They are provided from many kinds of chip, and are familiar to Linux developers working with embedded and custom hardware. Each GPIO represents a bit connected to a particular pin, or "ball" on Ball Grid Array (BGA) packages. Board schematics show which external hardware connects to which GPIOs. Drivers can be written generically, so that board setup code passes such pin configuration data to drivers. System-on-Chip (SOC) processors heavily rely on GPIOs. In some cases, every non-dedicated pin can be configured as a GPIO; and most chips have at least several dozen of them. Programmable logic devices (like FPGAs) can easily provide GPIOs; multifunction chips like power managers, and audio codecs often have a few such pins to help with pin scarcity on SOCs; and there are also "GPIO Expander" chips that connect using the I2C or SPI serial busses. Most PC southbridges have a few dozen GPIO-capable pins (with only the BIOS firmware knowing how they're used). The exact capabilities of GPIOs vary between systems. Common options: - Output values are writable (high=1, low=0). Some chips also have options about how that value is driven, so that for example only one value might be driven ... supporting "wire-OR" and similar schemes |
1668be71c [PATCH] doc: gpio... |
31 |
for the other value (notably, "open drain" signaling). |
4c20386c8 [PATCH] GPIO core |
32 33 34 35 |
- Input values are likewise readable (1, 0). Some chips support readback of pins configured as "output", which is very useful in such "wire-OR" cases (to support bidirectional signaling). GPIO controllers may have |
7c2db759e gpiolib: update D... |
36 |
input de-glitch/debounce logic, sometimes with software controls. |
4c20386c8 [PATCH] GPIO core |
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 |
- Inputs can often be used as IRQ signals, often edge triggered but sometimes level triggered. Such IRQs may be configurable as system wakeup events, to wake the system from a low power state. - Usually a GPIO will be configurable as either input or output, as needed by different product boards; single direction ones exist too. - Most GPIOs can be accessed while holding spinlocks, but those accessed through a serial bus normally can't. Some systems support both types. On a given board each GPIO is used for one specific purpose like monitoring MMC/SD card insertion/removal, detecting card writeprotect status, driving a LED, configuring a transceiver, bitbanging a serial bus, poking a hardware watchdog, sensing a switch, and so on. GPIO conventions ================ Note that this is called a "convention" because you don't need to do it this way, and it's no crime if you don't. There **are** cases where portability is not the main issue; GPIOs are often used for the kind of board-specific glue logic that may even change between board revisions, and can't ever be used on a board that's wired differently. Only least-common-denominator functionality can be very portable. Other features are platform-specific, and that can be critical for glue logic. |
7c2db759e gpiolib: update D... |
63 |
Plus, this doesn't require any implementation framework, just an interface. |
4c20386c8 [PATCH] GPIO core |
64 65 |
One platform might implement it as simple inline functions accessing chip registers; another might implement it by delegating through abstractions |
7c2db759e gpiolib: update D... |
66 67 68 69 |
used for several very different kinds of GPIO controller. (There is some optional code supporting such an implementation strategy, described later in this document, but drivers acting as clients to the GPIO interface must not care how it's implemented.) |
4c20386c8 [PATCH] GPIO core |
70 71 |
That said, if the convention is supported on their platform, drivers should |
7560fa60f gpio: <linux/gpio... |
72 73 74 75 76 |
use it when possible. Platforms must declare GENERIC_GPIO support in their Kconfig (boolean true), and provide an <asm/gpio.h> file. Drivers that can't work without standard GPIO calls should have Kconfig entries which depend on GENERIC_GPIO. The GPIO calls are available, either as "real code" or as optimized-away stubs, when drivers use the include file: |
4c20386c8 [PATCH] GPIO core |
77 |
|
7560fa60f gpio: <linux/gpio... |
78 |
#include <linux/gpio.h> |
4c20386c8 [PATCH] GPIO core |
79 80 81 |
If you stick to this convention then it'll be easier for other developers to see what your code is doing, and help maintain it. |
a0a998350 gpio calls don't ... |
82 83 |
Note that these operations include I/O barriers on platforms which need to use them; drivers don't need to add them explicitly. |
4c20386c8 [PATCH] GPIO core |
84 85 86 87 88 |
Identifying GPIOs ----------------- GPIOs are identified by unsigned integers in the range 0..MAX_INT. That reserves "negative" numbers for other purposes like marking signals as |
f5de61114 [PATCH] GPIO core... |
89 90 |
"not available on this board", or indicating faults. Code that doesn't touch the underlying hardware treats these integers as opaque cookies. |
4c20386c8 [PATCH] GPIO core |
91 92 93 94 95 96 97 98 99 100 101 102 103 |
Platforms define how they use those integers, and usually #define symbols for the GPIO lines so that board-specific setup code directly corresponds to the relevant schematics. In contrast, drivers should only use GPIO numbers passed to them from that setup code, using platform_data to hold board-specific pin configuration data (along with other board specific data they need). That avoids portability problems. So for example one platform uses numbers 32-159 for GPIOs; while another uses numbers 0..63 with one set of GPIO controllers, 64-79 with another type of GPIO controller, and on one particular board 80-95 with an FPGA. The numbers need not be contiguous; either of those platforms could also use numbers 2000-2063 to identify GPIOs in a bank of I2C GPIO expanders. |
e6de1808f gpio: define gpio... |
104 105 |
If you want to initialize a structure with an invalid GPIO number, use some negative number (perhaps "-EINVAL"); that will never be valid. To |
c956126c1 gpio: doc updates |
106 107 |
test if such number from such a structure could reference a GPIO, you may use this predicate: |
e6de1808f gpio: define gpio... |
108 109 110 111 112 |
int gpio_is_valid(int number); A number that's not valid will be rejected by calls which may request or free GPIOs (see below). Other numbers may also be rejected; for |
c956126c1 gpio: doc updates |
113 |
example, a number might be valid but temporarily unused on a given board. |
4c20386c8 [PATCH] GPIO core |
114 |
|
c956126c1 gpio: doc updates |
115 116 117 118 |
Whether a platform supports multiple GPIO controllers is a platform-specific implementation issue, as are whether that support can leave "holes" in the space of GPIO numbers, and whether new controllers can be added at runtime. Such issues can affect things including whether adjacent GPIO numbers are both valid. |
4c20386c8 [PATCH] GPIO core |
119 120 121 |
Using GPIOs ----------- |
8a0cecffe gpio: gpio_{reque... |
122 123 124 125 |
The first thing a system should do with a GPIO is allocate it, using the gpio_request() call; see later. One of the next things to do with a GPIO, often in board setup code when |
4c20386c8 [PATCH] GPIO core |
126 127 128 129 |
setting up a platform_device using the GPIO, is mark its direction: /* set as input or output, returning 0 or negative errno */ int gpio_direction_input(unsigned gpio); |
28735a725 [PATCH] gpio_dire... |
130 |
int gpio_direction_output(unsigned gpio, int value); |
4c20386c8 [PATCH] GPIO core |
131 132 133 |
The return value is zero for success, else a negative errno. It should be checked, since the get/set calls don't have error returns and since |
83c6590cb gpio interface lo... |
134 135 136 |
misconfiguration is possible. You should normally issue these calls from a task context. However, for spinlock-safe GPIOs it's OK to use them before tasking is enabled, as part of early board setup. |
4c20386c8 [PATCH] GPIO core |
137 |
|
28735a725 [PATCH] gpio_dire... |
138 139 |
For output GPIOs, the value provided becomes the initial output value. This helps avoid signal glitching during system startup. |
7c2db759e gpiolib: update D... |
140 141 |
For compatibility with legacy interfaces to GPIOs, setting the direction of a GPIO implicitly requests that GPIO (see below) if it has not been |
8a0cecffe gpio: gpio_{reque... |
142 143 |
requested already. That compatibility is being removed from the optional gpiolib framework. |
7c2db759e gpiolib: update D... |
144 |
|
4c20386c8 [PATCH] GPIO core |
145 146 147 148 149 150 151 152 153 154 155 |
Setting the direction can fail if the GPIO number is invalid, or when that particular GPIO can't be used in that mode. It's generally a bad idea to rely on boot firmware to have set the direction correctly, since it probably wasn't validated to do more than boot Linux. (Similarly, that board setup code probably needs to multiplex that pin as a GPIO, and configure pullups/pulldowns appropriately.) Spinlock-Safe GPIO access ------------------------- Most GPIO controllers can be accessed with memory read/write instructions. |
9c4ba9466 gpiolib: decouple... |
156 157 |
Those don't need to sleep, and can safely be done from inside hard (nonthreaded) IRQ handlers and similar contexts. |
4c20386c8 [PATCH] GPIO core |
158 |
|
9c4ba9466 gpiolib: decouple... |
159 160 |
Use the following calls to access such GPIOs, for which gpio_cansleep() will always return false (see below): |
4c20386c8 [PATCH] GPIO core |
161 162 163 164 165 166 167 168 169 170 |
/* GPIO INPUT: return zero or nonzero */ int gpio_get_value(unsigned gpio); /* GPIO OUTPUT */ void gpio_set_value(unsigned gpio, int value); The values are boolean, zero for low, nonzero for high. When reading the value of an output pin, the value returned should be what's seen on the pin ... that won't always match the specified output value, because of |
7c2db759e gpiolib: update D... |
171 |
issues including open-drain signaling and output latencies. |
4c20386c8 [PATCH] GPIO core |
172 173 |
The get/set calls have no error returns because "invalid GPIO" should have |
be1ff386e minor gpio doc up... |
174 |
been reported earlier from gpio_direction_*(). However, note that not all |
4c20386c8 [PATCH] GPIO core |
175 |
platforms can read the value of output pins; those that can't should always |
f5de61114 [PATCH] GPIO core... |
176 177 |
return zero. Also, using these calls for GPIOs that can't safely be accessed without sleeping (see below) is an error. |
4c20386c8 [PATCH] GPIO core |
178 |
|
f5de61114 [PATCH] GPIO core... |
179 |
Platform-specific implementations are encouraged to optimize the two |
4c20386c8 [PATCH] GPIO core |
180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 |
calls to access the GPIO value in cases where the GPIO number (and for output, value) are constant. It's normal for them to need only a couple of instructions in such cases (reading or writing a hardware register), and not to need spinlocks. Such optimized calls can make bitbanging applications a lot more efficient (in both space and time) than spending dozens of instructions on subroutine calls. GPIO access that may sleep -------------------------- Some GPIO controllers must be accessed using message based busses like I2C or SPI. Commands to read or write those GPIO values require waiting to get to the head of a queue to transmit a command and get its response. This requires sleeping, which can't be done from inside IRQ handlers. Platforms that support this type of GPIO distinguish them from other GPIOs |
7c2db759e gpiolib: update D... |
196 |
by returning nonzero from this call (which requires a valid GPIO number, |
8a0cecffe gpio: gpio_{reque... |
197 |
which should have been previously allocated with gpio_request): |
4c20386c8 [PATCH] GPIO core |
198 199 200 201 202 203 204 205 206 207 |
int gpio_cansleep(unsigned gpio); To access such GPIOs, a different set of accessors is defined: /* GPIO INPUT: return zero or nonzero, might sleep */ int gpio_get_value_cansleep(unsigned gpio); /* GPIO OUTPUT, might sleep */ void gpio_set_value_cansleep(unsigned gpio, int value); |
9c4ba9466 gpiolib: decouple... |
208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 |
Accessing such GPIOs requires a context which may sleep, for example a threaded IRQ handler, and those accessors must be used instead of spinlock-safe accessors without the cansleep() name suffix. Other than the fact that these accessors might sleep, and will work on GPIOs that can't be accessed from hardIRQ handlers, these calls act the same as the spinlock-safe calls. ** IN ADDITION ** calls to setup and configure such GPIOs must be made from contexts which may sleep, since they may need to access the GPIO controller chip too: (These setup calls are usually made from board setup or driver probe/teardown code, so this is an easy constraint.) gpio_direction_input() gpio_direction_output() gpio_request() ## gpio_request_one() ## gpio_request_array() ## gpio_free_array() gpio_free() gpio_set_debounce() |
4c20386c8 [PATCH] GPIO core |
232 |
|
8a0cecffe gpio: gpio_{reque... |
233 234 |
Claiming and Releasing GPIOs ---------------------------- |
4c20386c8 [PATCH] GPIO core |
235 |
To help catch system configuration errors, two calls are defined. |
4c20386c8 [PATCH] GPIO core |
236 237 238 239 240 241 242 243 244 245 246 |
/* request GPIO, returning 0 or negative errno. * non-null labels may be useful for diagnostics. */ int gpio_request(unsigned gpio, const char *label); /* release previously-claimed GPIO */ void gpio_free(unsigned gpio); Passing invalid GPIO numbers to gpio_request() will fail, as will requesting GPIOs that have already been claimed with that call. The return value of |
83c6590cb gpio interface lo... |
247 248 249 |
gpio_request() must be checked. You should normally issue these calls from a task context. However, for spinlock-safe GPIOs it's OK to request GPIOs before tasking is enabled, as part of early board setup. |
4c20386c8 [PATCH] GPIO core |
250 251 252 253 |
These calls serve two basic purposes. One is marking the signals which are actually in use as GPIOs, for better diagnostics; systems may have several hundred potential GPIOs, but often only a dozen are used on any |
7c2db759e gpiolib: update D... |
254 255 256 257 258 |
given board. Another is to catch conflicts, identifying errors when (a) two or more drivers wrongly think they have exclusive use of that signal, or (b) something wrongly believes it's safe to remove drivers needed to manage a signal that's in active use. That is, requesting a GPIO can serve as a kind of lock. |
4c20386c8 [PATCH] GPIO core |
259 |
|
35e8bb517 gpiolib: request/... |
260 261 262 |
Some platforms may also use knowledge about what GPIOs are active for power management, such as by powering down unused chip sectors and, more easily, gating off unused clocks. |
4c20386c8 [PATCH] GPIO core |
263 264 265 |
Note that requesting a GPIO does NOT cause it to be configured in any way; it just marks that GPIO as in use. Separate code must handle any pin setup (e.g. controlling which pin the GPIO uses, pullup/pulldown). |
7c2db759e gpiolib: update D... |
266 267 |
Also note that it's your responsibility to have stopped using a GPIO before you free it. |
3e45f1d11 gpio: introduce g... |
268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 |
Considering in most cases GPIOs are actually configured right after they are claimed, three additional calls are defined: /* request a single GPIO, with initial configuration specified by * 'flags', identical to gpio_request() wrt other arguments and * return value */ int gpio_request_one(unsigned gpio, unsigned long flags, const char *label); /* request multiple GPIOs in a single call */ int gpio_request_array(struct gpio *array, size_t num); /* release multiple GPIOs in a single call */ void gpio_free_array(struct gpio *array, size_t num); where 'flags' is currently defined to specify the following properties: * GPIOF_DIR_IN - to configure direction as input * GPIOF_DIR_OUT - to configure direction as output * GPIOF_INIT_LOW - as output, set initial level to LOW * GPIOF_INIT_HIGH - as output, set initial level to HIGH since GPIOF_INIT_* are only valid when configured as output, so group valid combinations as: * GPIOF_IN - configure as input * GPIOF_OUT_INIT_LOW - configured as output, initial level LOW * GPIOF_OUT_INIT_HIGH - configured as output, initial level HIGH In the future, these flags can be extended to support more properties such as open-drain status. Further more, to ease the claim/release of multiple GPIOs, 'struct gpio' is introduced to encapsulate all three fields as: struct gpio { unsigned gpio; unsigned long flags; const char *label; }; A typical example of usage: static struct gpio leds_gpios[] = { { 32, GPIOF_OUT_INIT_HIGH, "Power LED" }, /* default to ON */ { 33, GPIOF_OUT_INIT_LOW, "Green LED" }, /* default to OFF */ { 34, GPIOF_OUT_INIT_LOW, "Red LED" }, /* default to OFF */ { 35, GPIOF_OUT_INIT_LOW, "Blue LED" }, /* default to OFF */ { ... }, }; err = gpio_request_one(31, GPIOF_IN, "Reset Button"); if (err) ... err = gpio_request_array(leds_gpios, ARRAY_SIZE(leds_gpios)); if (err) ... gpio_free_array(leds_gpios, ARRAY_SIZE(leds_gpios)); |
4c20386c8 [PATCH] GPIO core |
331 332 333 334 335 336 337 338 339 |
GPIOs mapped to IRQs -------------------- GPIO numbers are unsigned integers; so are IRQ numbers. These make up two logically distinct namespaces (GPIO 0 need not use IRQ 0). You can map between them using calls like: /* map GPIO numbers to IRQ numbers */ int gpio_to_irq(unsigned gpio); |
0f6d504e7 gpiolib: gpio_to_... |
340 |
/* map IRQ numbers to GPIO numbers (avoid using this) */ |
4c20386c8 [PATCH] GPIO core |
341 342 343 344 |
int irq_to_gpio(unsigned irq); Those return either the corresponding number in the other namespace, or else a negative errno code if the mapping can't be done. (For example, |
7c2db759e gpiolib: update D... |
345 |
some GPIOs can't be used as IRQs.) It is an unchecked error to use a GPIO |
be1ff386e minor gpio doc up... |
346 |
number that wasn't set up as an input using gpio_direction_input(), or |
4c20386c8 [PATCH] GPIO core |
347 348 349 350 351 352 353 354 355 356 357 358 |
to use an IRQ number that didn't originally come from gpio_to_irq(). These two mapping calls are expected to cost on the order of a single addition or subtraction. They're not allowed to sleep. Non-error values returned from gpio_to_irq() can be passed to request_irq() or free_irq(). They will often be stored into IRQ resources for platform devices, by the board-specific initialization code. Note that IRQ trigger options are part of the IRQ interface, e.g. IRQF_TRIGGER_FALLING, as are system wakeup capabilities. Non-error values returned from irq_to_gpio() would most commonly be used |
f5de61114 [PATCH] GPIO core... |
359 |
with gpio_get_value(), for example to initialize or update driver state |
0f6d504e7 gpiolib: gpio_to_... |
360 361 |
when the IRQ is edge-triggered. Note that some platforms don't support this reverse mapping, so you should avoid using it. |
4c20386c8 [PATCH] GPIO core |
362 |
|
1668be71c [PATCH] doc: gpio... |
363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 |
Emulating Open Drain Signals ---------------------------- Sometimes shared signals need to use "open drain" signaling, where only the low signal level is actually driven. (That term applies to CMOS transistors; "open collector" is used for TTL.) A pullup resistor causes the high signal level. This is sometimes called a "wire-AND"; or more practically, from the negative logic (low=true) perspective this is a "wire-OR". One common example of an open drain signal is a shared active-low IRQ line. Also, bidirectional data bus signals sometimes use open drain signals. Some GPIO controllers directly support open drain outputs; many don't. When you need open drain signaling but your hardware doesn't directly support it, there's a common idiom you can use to emulate it with any GPIO pin that can be used as either an input or an output: LOW: gpio_direction_output(gpio, 0) ... this drives the signal and overrides the pullup. HIGH: gpio_direction_input(gpio) ... this turns off the output, so the pullup (or some other device) controls the signal. If you are "driving" the signal high but gpio_get_value(gpio) reports a low value (after the appropriate rise time passes), you know some other component is driving the shared signal low. That's not necessarily an error. As one common example, that's how I2C clocks are stretched: a slave that needs a slower clock delays the rising edge of SCK, and the I2C master adjusts its signaling rate accordingly. |
4c20386c8 [PATCH] GPIO core |
391 392 393 394 395 396 397 398 399 400 401 402 403 404 |
What do these conventions omit? =============================== One of the biggest things these conventions omit is pin multiplexing, since this is highly chip-specific and nonportable. One platform might not need explicit multiplexing; another might have just two options for use of any given pin; another might have eight options per pin; another might be able to route a given GPIO to any one of several pins. (Yes, those examples all come from systems that run Linux today.) Related to multiplexing is configuration and enabling of the pullups or pulldowns integrated on some platforms. Not all platforms support them, or support them in the same way; and any given board might use external pullups (or pulldowns) so that the on-chip ones should not be used. |
7c2db759e gpiolib: update D... |
405 |
(When a circuit needs 5 kOhm, on-chip 100 kOhm resistors won't do.) |
7560fa60f gpio: <linux/gpio... |
406 407 408 |
Likewise drive strength (2 mA vs 20 mA) and voltage (1.8V vs 3.3V) is a platform-specific issue, as are models like (not) having a one-to-one correspondence between configurable pins and GPIOs. |
4c20386c8 [PATCH] GPIO core |
409 410 411 412 |
There are other system-specific mechanisms that are not specified here, like the aforementioned options for input de-glitching and wire-OR output. Hardware may support reading or writing GPIOs in gangs, but that's usually |
f5de61114 [PATCH] GPIO core... |
413 |
configuration dependent: for GPIOs sharing the same bank. (GPIOs are |
4c20386c8 [PATCH] GPIO core |
414 |
commonly grouped in banks of 16 or 32, with a given SOC having several such |
7c2db759e gpiolib: update D... |
415 416 417 |
banks.) Some systems can trigger IRQs from output GPIOs, or read values from pins not managed as GPIOs. Code relying on such mechanisms will necessarily be nonportable. |
4c20386c8 [PATCH] GPIO core |
418 |
|
7c2db759e gpiolib: update D... |
419 |
Dynamic definition of GPIOs is not currently standard; for example, as |
4c20386c8 [PATCH] GPIO core |
420 |
a side effect of configuring an add-on board with some GPIO expanders. |
7c2db759e gpiolib: update D... |
421 422 423 424 425 |
GPIO implementor's framework (OPTIONAL) ======================================= As noted earlier, there is an optional implementation framework making it easier for platforms to support different kinds of GPIO controller using |
d8f388d8d gpio: sysfs inter... |
426 |
the same programming interface. This framework is called "gpiolib". |
7c2db759e gpiolib: update D... |
427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 |
As a debugging aid, if debugfs is available a /sys/kernel/debug/gpio file will be found there. That will list all the controllers registered through this framework, and the state of the GPIOs currently in use. Controller Drivers: gpio_chip ----------------------------- In this framework each GPIO controller is packaged as a "struct gpio_chip" with information common to each controller of that type: - methods to establish GPIO direction - methods used to access GPIO values - flag saying whether calls to its methods may sleep - optional debugfs dump method (showing extra state like pullup config) - label for diagnostics There is also per-instance data, which may come from device.platform_data: the number of its first GPIO, and how many GPIOs it exposes. The code implementing a gpio_chip should support multiple instances of the controller, possibly using the driver model. That code will configure each gpio_chip and issue gpiochip_add(). Removing a GPIO controller should be rare; use gpiochip_remove() when it is unavoidable. Most often a gpio_chip is part of an instance-specific structure with state not exposed by the GPIO interfaces, such as addressing, power management, |
bfc9dcabd correct gpio.txt ... |
454 |
and more. Chips such as codecs will have complex non-GPIO state. |
7c2db759e gpiolib: update D... |
455 456 457 458 459 460 461 462 |
Any debugfs dump method should normally ignore signals which haven't been requested as GPIOs. They can use gpiochip_is_requested(), which returns either NULL or the label associated with that GPIO when it was requested. Platform Support ---------------- |
7444a72ef gpiolib: allow us... |
463 464 |
To support this framework, a platform's Kconfig will "select" either ARCH_REQUIRE_GPIOLIB or ARCH_WANT_OPTIONAL_GPIOLIB |
7c2db759e gpiolib: update D... |
465 466 |
and arrange that its <asm/gpio.h> includes <asm-generic/gpio.h> and defines three functions: gpio_get_value(), gpio_set_value(), and gpio_cansleep(). |
7c2db759e gpiolib: update D... |
467 |
|
c956126c1 gpio: doc updates |
468 469 470 471 472 473 |
It may also provide a custom value for ARCH_NR_GPIOS, so that it better reflects the number of GPIOs in actual use on that platform, without wasting static table space. (It should count both built-in/SoC GPIOs and also ones on GPIO expanders. ARCH_REQUIRE_GPIOLIB means that the gpiolib code will always get compiled |
7444a72ef gpiolib: allow us... |
474 |
into the kernel on that architecture. |
c956126c1 gpio: doc updates |
475 |
ARCH_WANT_OPTIONAL_GPIOLIB means the gpiolib code defaults to off and the user |
7444a72ef gpiolib: allow us... |
476 477 478 479 |
can enable it and build it into the kernel optionally. If neither of these options are selected, the platform does not support GPIOs through GPIO-lib and the code cannot be enabled by the user. |
7c2db759e gpiolib: update D... |
480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 |
Trivial implementations of those functions can directly use framework code, which always dispatches through the gpio_chip: #define gpio_get_value __gpio_get_value #define gpio_set_value __gpio_set_value #define gpio_cansleep __gpio_cansleep Fancier implementations could instead define those as inline functions with logic optimizing access to specific SOC-based GPIOs. For example, if the referenced GPIO is the constant "12", getting or setting its value could cost as little as two or three instructions, never sleeping. When such an optimization is not possible those calls must delegate to the framework code, costing at least a few dozen instructions. For bitbanged I/O, such instruction savings can be significant. For SOCs, platform-specific code defines and registers gpio_chip instances for each bank of on-chip GPIOs. Those GPIOs should be numbered/labeled to match chip vendor documentation, and directly match board schematics. They may well start at zero and go up to a platform-specific limit. Such GPIOs are normally integrated into platform initialization to make them always be available, from arch_initcall() or earlier; they can often serve as IRQs. Board Support ------------- For external GPIO controllers -- such as I2C or SPI expanders, ASICs, multi function devices, FPGAs or CPLDs -- most often board-specific code handles registering controller devices and ensures that their drivers know what GPIO numbers to use with gpiochip_add(). Their numbers often start right after platform-specific GPIOs. For example, board setup code could create structures identifying the range of GPIOs that chip will expose, and passes them to each GPIO expander chip using platform_data. Then the chip driver's probe() routine could pass that data to gpiochip_add(). Initialization order can be important. For example, when a device relies on an I2C-based GPIO, its probe() routine should only be called after that GPIO becomes available. That may mean the device should not be registered until calls for that GPIO can work. One way to address such dependencies is for such gpio_chip controllers to provide setup() and teardown() callbacks to board specific code; those board specific callbacks would register devices |
d8f388d8d gpio: sysfs inter... |
522 523 524 525 526 527 528 529 530 531 532 |
once all the necessary resources are available, and remove them later when the GPIO controller device becomes unavailable. Sysfs Interface for Userspace (OPTIONAL) ======================================== Platforms which use the "gpiolib" implementors framework may choose to configure a sysfs user interface to GPIOs. This is different from the debugfs interface, since it provides control over GPIO direction and value instead of just showing a gpio state summary. Plus, it could be present on production systems without debugging support. |
19f594600 trivial: Miscella... |
533 |
Given appropriate hardware documentation for the system, userspace could |
d8f388d8d gpio: sysfs inter... |
534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 |
know for example that GPIO #23 controls the write protect line used to protect boot loader segments in flash memory. System upgrade procedures may need to temporarily remove that protection, first importing a GPIO, then changing its output state, then updating the code before re-enabling the write protection. In normal use, GPIO #23 would never be touched, and the kernel would have no need to know about it. Again depending on appropriate hardware documentation, on some systems userspace GPIO can be used to determine system configuration data that standard kernels won't know about. And for some tasks, simple userspace GPIO drivers could be all that the system really needs. Note that standard kernel drivers exist for common "LEDs and Buttons" GPIO tasks: "leds-gpio" and "gpio_keys", respectively. Use those instead of talking directly to the GPIOs; they integrate with kernel frameworks better than your userspace code could. Paths in Sysfs -------------- There are three kinds of entry in /sys/class/gpio: - Control interfaces used to get userspace control over GPIOs; - GPIOs themselves; and - GPIO controllers ("gpio_chip" instances). That's in addition to standard files including the "device" symlink. The control interfaces are write-only: /sys/class/gpio/ "export" ... Userspace may ask the kernel to export control of a GPIO to userspace by writing its number to this file. Example: "echo 19 > export" will create a "gpio19" node for GPIO #19, if that's not requested by kernel code. "unexport" ... Reverses the effect of exporting to userspace. Example: "echo 19 > unexport" will remove a "gpio19" node exported using the "export" file. GPIO signals have paths like /sys/class/gpio/gpio42/ (for GPIO #42) and have the following read/write attributes: /sys/class/gpio/gpioN/ "direction" ... reads as either "in" or "out". This value may normally be written. Writing as "out" defaults to initializing the value as low. To ensure glitch free operation, values "low" and "high" may be written to configure the GPIO as an output with that initial value. Note that this attribute *will not exist* if the kernel doesn't support changing the direction of a GPIO, or it was exported by kernel code that didn't explicitly allow userspace to reconfigure this GPIO's direction. "value" ... reads as either 0 (low) or 1 (high). If the GPIO is configured as an output, this value may be written; any nonzero value is treated as high. |
ff77c352a gpiolib: allow po... |
598 599 600 601 602 603 |
"edge" ... reads as either "none", "rising", "falling", or "both". Write these strings to select the signal edge(s) that will make poll(2) on the "value" file return. This file exists only if the pin can be configured as an interrupt generating input pin. |
076974618 gpiolib: add supp... |
604 605 606 607 608 609 |
"active_low" ... reads as either 0 (false) or 1 (true). Write any nonzero value to invert the value attribute both for reading and writing. Existing and subsequent poll(2) support configuration via the edge attribute for "rising" and "falling" edges will follow this setting. |
bfc9dcabd correct gpio.txt ... |
610 |
GPIO controllers have paths like /sys/class/gpio/gpiochip42/ (for the |
d8f388d8d gpio: sysfs inter... |
611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 |
controller implementing GPIOs starting at #42) and have the following read-only attributes: /sys/class/gpio/gpiochipN/ "base" ... same as N, the first GPIO managed by this chip "label" ... provided for diagnostics (not always unique) "ngpio" ... how many GPIOs this manges (N to N + ngpio - 1) Board documentation should in most cases cover what GPIOs are used for what purposes. However, those numbers are not always stable; GPIOs on a daughtercard might be different depending on the base board being used, or other cards in the stack. In such cases, you may need to use the gpiochip nodes (possibly in conjunction with schematics) to determine the correct GPIO number to use for a given signal. Exporting from Kernel code -------------------------- Kernel code can explicitly manage exports of GPIOs which have already been requested using gpio_request(): /* export the GPIO to userspace */ int gpio_export(unsigned gpio, bool direction_may_change); /* reverse gpio_export() */ void gpio_unexport(); |
a4177ee7f gpiolib: allow ex... |
640 641 642 |
/* create a sysfs link to an exported GPIO node */ int gpio_export_link(struct device *dev, const char *name, unsigned gpio) |
076974618 gpiolib: add supp... |
643 644 |
/* change the polarity of a GPIO node in sysfs */ int gpio_sysfs_set_active_low(unsigned gpio, int value); |
a4177ee7f gpiolib: allow ex... |
645 |
|
d8f388d8d gpio: sysfs inter... |
646 647 648 649 650 651 652 653 |
After a kernel driver requests a GPIO, it may only be made available in the sysfs interface by gpio_export(). The driver can control whether the signal direction may change. This helps drivers prevent userspace code from accidentally clobbering important system state. This explicit exporting can help with debugging (by making some kinds of experiments easier), or can provide an always-there interface that's suitable for documenting as part of a board support package. |
a4177ee7f gpiolib: allow ex... |
654 655 656 657 658 |
After the GPIO has been exported, gpio_export_link() allows creating symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can use this to provide the interface under their own device in sysfs with a descriptive name. |
076974618 gpiolib: add supp... |
659 660 661 662 663 664 |
Drivers can use gpio_sysfs_set_active_low() to hide GPIO line polarity differences between boards from user space. This only affects the sysfs interface. Polarity change can be done both before and after gpio_export(), and previously enabled poll(2) support for either rising or falling edge will be reconfigured to follow this setting. |