Blame view
drivers/ata/pata_opti.c
5.4 KB
669a5db41
|
1 2 3 |
/* * pata_opti.c - ATI PATA for new ATA layer * (C) 2005 Red Hat Inc |
669a5db41
|
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 |
* * Based on * linux/drivers/ide/pci/opti621.c Version 0.7 Sept 10, 2002 * * Copyright (C) 1996-1998 Linus Torvalds & authors (see below) * * Authors: * Jaromir Koutek <miri@punknet.cz>, * Jan Harkes <jaharkes@cwi.nl>, * Mark Lord <mlord@pobox.com> * Some parts of code are from ali14xx.c and from rz1000.c. * * Also consulted the FreeBSD prototype driver by Kevin Day to try * and resolve some confusions. Further documentation can be found in * Ralf Brown's interrupt list * * If you have other variants of the Opti range (Viper/Vendetta) please * try this driver with those PCI idents and report back. For the later * chips see the pata_optidma driver * */ #include <linux/kernel.h> #include <linux/module.h> #include <linux/pci.h> #include <linux/init.h> #include <linux/blkdev.h> #include <linux/delay.h> #include <scsi/scsi_host.h> #include <linux/libata.h> #define DRV_NAME "pata_opti" |
a0fcdc025
|
36 |
#define DRV_VERSION "0.2.9" |
669a5db41
|
37 38 39 40 41 42 43 44 45 46 47 |
enum { READ_REG = 0, /* index of Read cycle timing register */ WRITE_REG = 1, /* index of Write cycle timing register */ CNTRL_REG = 3, /* index of Control register */ STRAP_REG = 5, /* index of Strap register */ MISC_REG = 6 /* index of Miscellaneous register */ }; /** * opti_pre_reset - probe begin |
cc0680a58
|
48 |
* @link: ATA link |
d4b2bab4f
|
49 |
* @deadline: deadline jiffies for the operation |
669a5db41
|
50 51 52 |
* * Set up cable type and use generic probe init */ |
cc0680a58
|
53 |
static int opti_pre_reset(struct ata_link *link, unsigned long deadline) |
669a5db41
|
54 |
{ |
cc0680a58
|
55 |
struct ata_port *ap = link->ap; |
669a5db41
|
56 57 58 59 60 |
struct pci_dev *pdev = to_pci_dev(ap->host->dev); static const struct pci_bits opti_enable_bits[] = { { 0x45, 1, 0x80, 0x00 }, { 0x40, 1, 0x08, 0x00 } }; |
c961922b7
|
61 62 |
if (!pci_test_config_bits(pdev, &opti_enable_bits[ap->port_no])) return -ENOENT; |
d4b2bab4f
|
63 |
|
9363c3825
|
64 |
return ata_sff_prereset(link, deadline); |
669a5db41
|
65 66 67 |
} /** |
669a5db41
|
68 69 70 71 72 73 74 75 76 77 78 79 80 |
* opti_write_reg - control register setup * @ap: ATA port * @value: value * @reg: control register number * * The Opti uses magic 'trapdoor' register accesses to do configuration * rather than using PCI space as other controllers do. The double inw * on the error register activates configuration mode. We can then write * the control register */ static void opti_write_reg(struct ata_port *ap, u8 val, int reg) { |
0d5ff5667
|
81 |
void __iomem *regio = ap->ioaddr.cmd_addr; |
669a5db41
|
82 83 |
/* These 3 unlock the control register access */ |
0d5ff5667
|
84 85 86 |
ioread16(regio + 1); ioread16(regio + 1); iowrite8(3, regio + 2); |
669a5db41
|
87 88 |
/* Do the I/O */ |
0d5ff5667
|
89 |
iowrite8(val, regio + reg); |
669a5db41
|
90 91 |
/* Relock */ |
0d5ff5667
|
92 |
iowrite8(0x83, regio + 2); |
669a5db41
|
93 |
} |
669a5db41
|
94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 |
/** * opti_set_piomode - set initial PIO mode data * @ap: ATA interface * @adev: ATA device * * Called to do the PIO mode setup. Timing numbers are taken from * the FreeBSD driver then pre computed to keep the code clean. There * are two tables depending on the hardware clock speed. */ static void opti_set_piomode(struct ata_port *ap, struct ata_device *adev) { struct ata_device *pair = ata_dev_pair(adev); int clock; int pio = adev->pio_mode - XFER_PIO_0; |
0d5ff5667
|
109 |
void __iomem *regio = ap->ioaddr.cmd_addr; |
669a5db41
|
110 111 112 113 114 115 116 117 118 119 120 |
u8 addr; /* Address table precomputed with prefetch off and a DCLK of 2 */ static const u8 addr_timing[2][5] = { { 0x30, 0x20, 0x20, 0x10, 0x10 }, { 0x20, 0x20, 0x10, 0x10, 0x10 } }; static const u8 data_rec_timing[2][5] = { { 0x6B, 0x56, 0x42, 0x32, 0x31 }, { 0x58, 0x44, 0x32, 0x22, 0x21 } }; |
0d5ff5667
|
121 122 |
iowrite8(0xff, regio + 5); clock = ioread16(regio + 5) & 1; |
669a5db41
|
123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 |
/* * As with many controllers the address setup time is shared * and must suit both devices if present. */ addr = addr_timing[clock][pio]; if (pair) { /* Hardware constraint */ u8 pair_addr = addr_timing[clock][pair->pio_mode - XFER_PIO_0]; if (pair_addr > addr) addr = pair_addr; } /* Commence primary programming sequence */ opti_write_reg(ap, adev->devno, MISC_REG); opti_write_reg(ap, data_rec_timing[clock][pio], READ_REG); opti_write_reg(ap, data_rec_timing[clock][pio], WRITE_REG); opti_write_reg(ap, addr, MISC_REG); /* Programming sequence complete, override strapping */ opti_write_reg(ap, 0x85, CNTRL_REG); } static struct scsi_host_template opti_sht = { |
68d1d07b5
|
148 |
ATA_PIO_SHT(DRV_NAME), |
669a5db41
|
149 150 151 |
}; static struct ata_port_operations opti_port_ops = { |
029cfd6b7
|
152 153 |
.inherits = &ata_sff_port_ops, .cable_detect = ata_cable_40wire, |
669a5db41
|
154 |
.set_piomode = opti_set_piomode, |
a1efdaba2
|
155 |
.prereset = opti_pre_reset, |
669a5db41
|
156 157 158 159 |
}; static int opti_init_one(struct pci_dev *dev, const struct pci_device_id *id) { |
1626aeb88
|
160 |
static const struct ata_port_info info = { |
1d2808fd3
|
161 |
.flags = ATA_FLAG_SLAVE_POSS, |
14bdef982
|
162 |
.pio_mask = ATA_PIO4, |
669a5db41
|
163 164 |
.port_ops = &opti_port_ops }; |
1626aeb88
|
165 |
const struct ata_port_info *ppi[] = { &info, NULL }; |
669a5db41
|
166 |
|
06296a1e6
|
167 |
ata_print_version_once(&dev->dev, DRV_VERSION); |
669a5db41
|
168 |
|
16ea0fc98
|
169 |
return ata_pci_sff_init_one(dev, ppi, &opti_sht, NULL, 0); |
669a5db41
|
170 171 172 |
} static const struct pci_device_id opti[] = { |
2d2744fc8
|
173 174 175 176 |
{ PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C621), 0 }, { PCI_VDEVICE(OPTI, PCI_DEVICE_ID_OPTI_82C825), 1 }, { }, |
669a5db41
|
177 178 179 |
}; static struct pci_driver opti_pci_driver = { |
2d2744fc8
|
180 |
.name = DRV_NAME, |
669a5db41
|
181 182 |
.id_table = opti, .probe = opti_init_one, |
30ced0f0d
|
183 |
.remove = ata_pci_remove_one, |
438ac6d5e
|
184 |
#ifdef CONFIG_PM |
30ced0f0d
|
185 186 |
.suspend = ata_pci_device_suspend, .resume = ata_pci_device_resume, |
438ac6d5e
|
187 |
#endif |
669a5db41
|
188 189 190 191 192 193 |
}; static int __init opti_init(void) { return pci_register_driver(&opti_pci_driver); } |
669a5db41
|
194 195 196 197 198 199 200 201 202 203 204 205 206 207 |
static void __exit opti_exit(void) { pci_unregister_driver(&opti_pci_driver); } MODULE_AUTHOR("Alan Cox"); MODULE_DESCRIPTION("low-level driver for Opti 621/621X"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, opti); MODULE_VERSION(DRV_VERSION); module_init(opti_init); module_exit(opti_exit); |