Kernel driver ltc4245
  =====================
  
  Supported chips:
    * Linear Technology LTC4245
      Prefix: 'ltc4245'
      Addresses scanned: 0x20-0x3f
      Datasheet:
          http://www.linear.com/pc/downloadDocument.do?navId=H0,C1,C1003,C1006,C1140,P19392,D13517
  
  Author: Ira W. Snyder <iws@ovro.caltech.edu>
  
  
  Description
  -----------
  
  The LTC4245 controller allows a board to be safely inserted and removed
  from a live backplane in multiple supply systems such as CompactPCI and
  PCI Express.
  
  
  Usage Notes
  -----------
  
  This driver does not probe for LTC4245 devices, due to the fact that some

  of the possible addresses are unfriendly to probing. You will have to
  instantiate the devices explicitly.

  
  Example: the following will load the driver for an LTC4245 at address 0x23
  on I2C bus #1:

  $ modprobe ltc4245
  $ echo ltc4245 0x23 > /sys/bus/i2c/devices/i2c-1/new_device

  
  
  Sysfs entries
  -------------
  
  The LTC4245 has built-in limits for over and under current warnings. This
  makes it very likely that the reference circuit will be used.
  
  This driver uses the values in the datasheet to change the register values
  into the values specified in the sysfs-interface document. The current readings
  rely on the sense resistors listed in Table 2: "Sense Resistor Values".
  
  in1_input		12v input voltage (mV)
  in2_input		5v  input voltage (mV)
  in3_input		3v  input voltage (mV)
  in4_input		Vee (-12v) input voltage (mV)
  
  in1_min_alarm		12v input undervoltage alarm
  in2_min_alarm		5v  input undervoltage alarm
  in3_min_alarm		3v  input undervoltage alarm
  in4_min_alarm		Vee (-12v) input undervoltage alarm
  
  curr1_input		12v current (mA)
  curr2_input		5v  current (mA)
  curr3_input		3v  current (mA)
  curr4_input		Vee (-12v) current (mA)
  
  curr1_max_alarm		12v overcurrent alarm
  curr2_max_alarm		5v  overcurrent alarm
  curr3_max_alarm		3v  overcurrent alarm
  curr4_max_alarm		Vee (-12v) overcurrent alarm
  
  in5_input		12v output voltage (mV)
  in6_input		5v  output voltage (mV)
  in7_input		3v  output voltage (mV)
  in8_input		Vee (-12v) output voltage (mV)
  
  in5_min_alarm		12v output undervoltage alarm
  in6_min_alarm		5v  output undervoltage alarm
  in7_min_alarm		3v  output undervoltage alarm
  in8_min_alarm		Vee (-12v) output undervoltage alarm

  in9_input		GPIO voltage data (see note 1)
  in10_input		GPIO voltage data (see note 1)
  in11_input		GPIO voltage data (see note 1)

  
  power1_input		12v power usage (mW)
  power2_input		5v  power usage (mW)
  power3_input		3v  power usage (mW)
  power4_input		Vee (-12v) power usage (mW)

  
  
  Note 1
  ------
  
  If you have NOT configured the driver to sample all GPIO pins as analog
  voltages, then the in10_input and in11_input sysfs attributes will not be
  created. The driver will sample the GPIO pin that is currently connected to the
  ADC as an analog voltage, and report the value in in9_input.
  
  If you have configured the driver to sample all GPIO pins as analog voltages,
  then they will be sampled in round-robin fashion. If userspace reads too
  slowly, -EAGAIN will be returned when you read the sysfs attribute containing
  the sensor reading.
  
  The LTC4245 chip can be configured to sample all GPIO pins with two methods:
  1) platform data -- see include/linux/i2c/ltc4245.h
  2) OF device tree -- add the "ltc4245,use-extra-gpios" property to each chip
  
  The default mode of operation is to sample a single GPIO pin.