Blame view
drivers/clocksource/scx200_hrt.c
2.99 KB
6ae7440e6 [PATCH] GTOD: add... |
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 |
/* * Copyright (C) 2006 Jim Cromie * * This is a clocksource driver for the Geode SCx200's 1 or 27 MHz * high-resolution timer. The Geode SC-1100 (at least) has a buggy * time stamp counter (TSC), which loses time unless 'idle=poll' is * given as a boot-arg. In its absence, the Generic Timekeeping code * will detect and de-rate the bad TSC, allowing this timer to take * over timekeeping duties. * * Based on work by John Stultz, and Ted Phelps (in a 2.6.12-rc6 patch) * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of the * License, or (at your option) any later version. */ #include <linux/clocksource.h> #include <linux/init.h> #include <linux/module.h> #include <linux/ioport.h> #include <linux/scx200.h> #define NAME "scx200_hrt" static int mhz27; module_param(mhz27, int, 0); /* load time only */ MODULE_PARM_DESC(mhz27, "count at 27.0 MHz (default is 1.0 MHz)"); static int ppm; module_param(ppm, int, 0); /* load time only */ MODULE_PARM_DESC(ppm, "+-adjust to actual XO freq (ppm)"); /* HiRes Timer configuration register address */ #define SCx200_TMCNFG_OFFSET (SCx200_TIMER_OFFSET + 5) /* and config settings */ #define HR_TMEN (1 << 0) /* timer interrupt enable */ #define HR_TMCLKSEL (1 << 1) /* 1|0 counts at 27|1 MHz */ #define HR_TM27MPD (1 << 2) /* 1 turns off input clock (power-down) */ /* The base timer frequency, * 27 if selected */ #define HRT_FREQ 1000000 |
8e19608e8 clocksource: pass... |
45 |
static cycle_t read_hrt(struct clocksource *cs) |
6ae7440e6 [PATCH] GTOD: add... |
46 47 48 49 50 51 52 53 54 55 56 57 58 |
{ /* Read the timer value */ return (cycle_t) inl(scx200_cb_base + SCx200_TIMER_OFFSET); } #define HRT_SHIFT_1 22 #define HRT_SHIFT_27 26 static struct clocksource cs_hrt = { .name = "scx200_hrt", .rating = 250, .read = read_hrt, .mask = CLOCKSOURCE_MASK(32), |
73b08d2aa [PATCH] clocksour... |
59 |
.flags = CLOCK_SOURCE_IS_CONTINUOUS, |
6ae7440e6 [PATCH] GTOD: add... |
60 61 62 63 64 |
/* mult, shift are set based on mhz27 flag */ }; static int __init init_hrt_clocksource(void) { |
856fe98f1 [PATCH] scx200_hr... |
65 |
/* Make sure scx200 has initialized the configuration block */ |
6ae7440e6 [PATCH] GTOD: add... |
66 67 68 69 70 71 72 73 74 75 76 77 78 |
if (!scx200_cb_present()) return -ENODEV; /* Reserve the timer's ISA io-region for ourselves */ if (!request_region(scx200_cb_base + SCx200_TIMER_OFFSET, SCx200_TIMER_SIZE, "NatSemi SCx200 High-Resolution Timer")) { printk(KERN_WARNING NAME ": unable to lock timer region "); return -ENODEV; } /* write timer config */ |
856fe98f1 [PATCH] scx200_hr... |
79 |
outb(HR_TMEN | (mhz27 ? HR_TMCLKSEL : 0), |
6ae7440e6 [PATCH] GTOD: add... |
80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 |
scx200_cb_base + SCx200_TMCNFG_OFFSET); if (mhz27) { cs_hrt.shift = HRT_SHIFT_27; cs_hrt.mult = clocksource_hz2mult((HRT_FREQ + ppm) * 27, cs_hrt.shift); } else { cs_hrt.shift = HRT_SHIFT_1; cs_hrt.mult = clocksource_hz2mult(HRT_FREQ + ppm, cs_hrt.shift); } printk(KERN_INFO "enabling scx200 high-res timer (%s MHz +%d ppm) ", mhz27 ? "27":"1", ppm); return clocksource_register(&cs_hrt); } module_init(init_hrt_clocksource); MODULE_AUTHOR("Jim Cromie <jim.cromie@gmail.com>"); MODULE_DESCRIPTION("clocksource on SCx200 HiRes Timer"); MODULE_LICENSE("GPL"); |