Blame view
drivers/ide/dtc2278.c
3.8 KB
1da177e4c Linux-2.6.12-rc2 |
1 |
/* |
1da177e4c Linux-2.6.12-rc2 |
2 3 |
* Copyright (C) 1996 Linus Torvalds & author (see below) */ |
1da177e4c Linux-2.6.12-rc2 |
4 |
#include <linux/module.h> |
1da177e4c Linux-2.6.12-rc2 |
5 6 7 8 9 10 11 |
#include <linux/types.h> #include <linux/kernel.h> #include <linux/delay.h> #include <linux/timer.h> #include <linux/mm.h> #include <linux/ioport.h> #include <linux/blkdev.h> |
1da177e4c Linux-2.6.12-rc2 |
12 13 14 15 |
#include <linux/ide.h> #include <linux/init.h> #include <asm/io.h> |
d92f1a282 ide: manage I/O r... |
16 |
#define DRV_NAME "dtc2278" |
1da177e4c Linux-2.6.12-rc2 |
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 |
/* * Changing this #undef to #define may solve start up problems in some systems. */ #undef ALWAYS_SET_DTC2278_PIO_MODE /* * From: andy@cercle.cts.com (Dyan Wile) * * Below is a patch for DTC-2278 - alike software-programmable controllers * The code enables the secondary IDE controller and the PIO4 (3?) timings on * the primary (EIDE). You may probably have to enable the 32-bit support to * get the full speed. You better get the disk interrupts disabled ( hdparm -u0 * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my * filesystem corrupted with -u1, but under heavy disk load only :-) * * This card is now forced to use the "serialize" feature, * and irq-unmasking is disallowed. If io_32bit is enabled, * it must be done for BOTH drives on each interface. * * This code was written for the DTC2278E, but might work with any of these: * * DTC2278S has only a single IDE interface. * DTC2278D has two IDE interfaces and is otherwise identical to the S version. * DTC2278E also has serial ports and a printer port * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu> * * There may be a fourth controller type. The S and D versions use the * Winbond chip, and I think the E version does also. * */ static void sub22 (char b, char c) { int i; for(i = 0; i < 3; ++i) { inb(0x3f6); outb_p(b,0xb0); inb(0x3f6); outb_p(c,0xb4); inb(0x3f6); if(inb(0xb4) == c) { outb_p(7,0xb0); inb(0x3f6); return; /* success */ } } } |
a34a8751f dtc2278: fix dead... |
65 |
static DEFINE_SPINLOCK(dtc2278_lock); |
e085b3cae ide: change ->set... |
66 |
static void dtc2278_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive) |
1da177e4c Linux-2.6.12-rc2 |
67 68 |
{ unsigned long flags; |
e085b3cae ide: change ->set... |
69 |
if (drive->pio_mode >= XFER_PIO_3) { |
a34a8751f dtc2278: fix dead... |
70 |
spin_lock_irqsave(&dtc2278_lock, flags); |
1da177e4c Linux-2.6.12-rc2 |
71 72 73 74 75 |
/* * This enables PIO mode4 (3?) on the first interface */ sub22(1,0xc3); sub22(0,0xa0); |
a34a8751f dtc2278: fix dead... |
76 |
spin_unlock_irqrestore(&dtc2278_lock, flags); |
1da177e4c Linux-2.6.12-rc2 |
77 78 |
} else { /* we don't know how to set it back again.. */ |
d3bad45f0 dtc2278: note on ... |
79 80 |
/* Actually we do - there is a data sheet available for the Winbond but does anyone actually care */ |
1da177e4c Linux-2.6.12-rc2 |
81 |
} |
1da177e4c Linux-2.6.12-rc2 |
82 |
} |
ac95beedf ide: add struct i... |
83 84 85 |
static const struct ide_port_ops dtc2278_port_ops = { .set_pio_mode = dtc2278_set_pio_mode, }; |
e6b53703b sections: fix sec... |
86 |
static const struct ide_port_info dtc2278_port_info __initconst = { |
d92f1a282 ide: manage I/O r... |
87 |
.name = DRV_NAME, |
c413b9b94 ide: add struct i... |
88 |
.chipset = ide_dtc2278, |
ac95beedf ide: add struct i... |
89 |
.port_ops = &dtc2278_port_ops, |
c413b9b94 ide: add struct i... |
90 |
.host_flags = IDE_HFLAG_SERIALIZE | |
807b90d0b ide: add IDE_HFLA... |
91 |
IDE_HFLAG_NO_UNMASK_IRQS | |
c413b9b94 ide: add struct i... |
92 |
IDE_HFLAG_IO_32BIT | |
807b90d0b ide: add IDE_HFLA... |
93 94 |
/* disallow ->io_32bit changes */ IDE_HFLAG_NO_IO_32BIT | |
2787cb8ae ide: add IDE_HFLA... |
95 96 |
IDE_HFLAG_NO_DMA | IDE_HFLAG_DTC2278, |
c413b9b94 ide: add struct i... |
97 98 |
.pio_mask = ATA_PIO4, }; |
849138827 ide: make legacy ... |
99 |
static int __init dtc2278_probe(void) |
1da177e4c Linux-2.6.12-rc2 |
100 101 |
{ unsigned long flags; |
1da177e4c Linux-2.6.12-rc2 |
102 |
|
1da177e4c Linux-2.6.12-rc2 |
103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 |
local_irq_save(flags); /* * This enables the second interface */ outb_p(4,0xb0); inb(0x3f6); outb_p(0x20,0xb4); inb(0x3f6); #ifdef ALWAYS_SET_DTC2278_PIO_MODE /* * This enables PIO mode4 (3?) on the first interface * and may solve start-up problems for some people. */ sub22(1,0xc3); sub22(0,0xa0); #endif local_irq_restore(flags); |
0bfeee7d4 ide: use ide_lega... |
120 |
return ide_legacy_device_add(&dtc2278_port_info, 0); |
1da177e4c Linux-2.6.12-rc2 |
121 |
} |
90ab5ee94 module_param: mak... |
122 |
static bool probe_dtc2278; |
849138827 ide: make legacy ... |
123 124 125 |
module_param_named(probe, probe_dtc2278, bool, 0); MODULE_PARM_DESC(probe, "probe for DTC2278xx chipsets"); |
ade2daf9c ide: make remaini... |
126 |
static int __init dtc2278_init(void) |
1da177e4c Linux-2.6.12-rc2 |
127 |
{ |
849138827 ide: make legacy ... |
128 129 130 131 |
if (probe_dtc2278 == 0) return -ENODEV; if (dtc2278_probe()) { |
1da177e4c Linux-2.6.12-rc2 |
132 133 134 135 136 137 |
printk(KERN_ERR "dtc2278: ide interfaces already in use! "); return -EBUSY; } return 0; } |
1da177e4c Linux-2.6.12-rc2 |
138 |
module_init(dtc2278_init); |
1da177e4c Linux-2.6.12-rc2 |
139 140 141 142 |
MODULE_AUTHOR("See Local File"); MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets"); MODULE_LICENSE("GPL"); |