Blame view

Documentation/hwmon/jc42 3.38 KB
4453d7364   Guenter Roeck   hwmon: add suppor...
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
  Kernel driver jc42
  ==================
  
  Supported chips:
    * Analog Devices ADT7408
      Prefix: 'adt7408'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
    * IDT TSE2002B3, TS3000B3
      Prefix: 'tse2002b3', 'ts3000b3'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://www.idt.com/products/getdoc.cfm?docid=18715691
  	http://www.idt.com/products/getdoc.cfm?docid=18715692
    * Maxim MAX6604
      Prefix: 'max6604'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
    * Microchip MCP9805, MCP98242, MCP98243, MCP9843
      Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
  	http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
  	http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
    * NXP Semiconductors SE97, SE97B
      Prefix: 'se97'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://www.nxp.com/documents/data_sheet/SE97.pdf
  	http://www.nxp.com/documents/data_sheet/SE97B.pdf
    * NXP Semiconductors SE98
      Prefix: 'se98'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://www.nxp.com/documents/data_sheet/SE98.pdf
    * ON Semiconductor CAT34TS02, CAT6095
      Prefix: 'cat34ts02', 'cat6095'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheet:
  	http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF
  	http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF
    * ST Microelectronics STTS424, STTS424E02
      Prefix: 'stts424'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheets:
  	http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
  	http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
    * JEDEC JC 42.4 compliant temperature sensor chips
      Prefix: 'jc42'
      Addresses scanned: I2C 0x18 - 0x1f
      Datasheet: -
  
  Author:
  	Guenter Roeck <guenter.roeck@ericsson.com>
  
  
  Description
  -----------
  
  This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
  The driver auto-detects the chips listed above, but can be manually instantiated
  to support other JC 42.4 compliant chips.
  
  Example: the following will load the driver for a generic JC 42.4 compliant
  temperature sensor at address 0x18 on I2C bus #1:
  
  # modprobe jc42
  # echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device
  
  A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum,
  and critical temperature can be configured. There are alarms for high, low,
  and critical thresholds.
  
  There is also an hysteresis to control the thresholds for resetting alarms.
  Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5,
  3.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those
  limits. The chip supports only a single register to configure the hysteresis,
  which applies to all limits. This register can be written by writing into
  temp1_crit_hyst. Other hysteresis attributes are read-only.
  
  Sysfs entries
  -------------
  
  temp1_input		Temperature (RO)
  temp1_min		Minimum temperature (RW)
  temp1_max		Maximum temperature (RW)
  temp1_crit		Critical high temperature (RW)
  
  temp1_crit_hyst		Critical hysteresis temperature (RW)
  temp1_max_hyst		Maximum hysteresis temperature (RO)
  
  temp1_min_alarm		Temperature low alarm
  temp1_max_alarm		Temperature high alarm
  temp1_crit_alarm	Temperature critical alarm