======================================
  Pulse Width Modulation (PWM) interface
  ======================================
  
  This provides an overview about the Linux PWM interface
  
  PWMs are commonly used for controlling LEDs, fans or vibrators in
  cell phones. PWMs with a fixed purpose have no need implementing
  the Linux PWM API (although they could). However, PWMs are often
  found as discrete devices on SoCs which have no fixed purpose. It's
  up to the board designer to connect them to LEDs or fans. To provide
  this kind of flexibility the generic PWM API exists.
  
  Identifying PWMs
  ----------------
  
  Users of the legacy PWM API use unique IDs to refer to PWM devices.
  
  Instead of referring to a PWM device via its unique ID, board setup code
  should instead register a static mapping that can be used to match PWM
  consumers to providers, as given in the following example::
  
  	static struct pwm_lookup board_pwm_lookup[] = {
  		PWM_LOOKUP("tegra-pwm", 0, "pwm-backlight", NULL,
  			   50000, PWM_POLARITY_NORMAL),
  	};
  
  	static void __init board_init(void)
  	{
  		...
  		pwm_add_table(board_pwm_lookup, ARRAY_SIZE(board_pwm_lookup));
  		...
  	}
  
  Using PWMs
  ----------
  
  Legacy users can request a PWM device using pwm_request() and free it
  after usage with pwm_free().
  
  New users should use the pwm_get() function and pass to it the consumer
  device or a consumer name. pwm_put() is used to free the PWM device. Managed
  variants of these functions, devm_pwm_get() and devm_pwm_put(), also exist.
  
  After being requested, a PWM has to be configured using::
  
  	int pwm_apply_state(struct pwm_device *pwm, struct pwm_state *state);
  
  This API controls both the PWM period/duty_cycle config and the
  enable/disable state.
  
  The pwm_config(), pwm_enable() and pwm_disable() functions are just wrappers
  around pwm_apply_state() and should not be used if the user wants to change
  several parameter at once. For example, if you see pwm_config() and
  pwm_{enable,disable}() calls in the same function, this probably means you
  should switch to pwm_apply_state().
  
  The PWM user API also allows one to query the PWM state with pwm_get_state().
  
  In addition to the PWM state, the PWM API also exposes PWM arguments, which
  are the reference PWM config one should use on this PWM.
  PWM arguments are usually platform-specific and allows the PWM user to only
  care about dutycycle relatively to the full period (like, duty = 50% of the
  period). struct pwm_args contains 2 fields (period and polarity) and should
  be used to set the initial PWM config (usually done in the probe function
  of the PWM user). PWM arguments are retrieved with pwm_get_args().
  
  Using PWMs with the sysfs interface
  -----------------------------------
  
  If CONFIG_SYSFS is enabled in your kernel configuration a simple sysfs
  interface is provided to use the PWMs from userspace. It is exposed at
  /sys/class/pwm/. Each probed PWM controller/chip will be exported as
  pwmchipN, where N is the base of the PWM chip. Inside the directory you
  will find:
  
    npwm
      The number of PWM channels this chip supports (read-only).
  
    export
      Exports a PWM channel for use with sysfs (write-only).
  
    unexport
     Unexports a PWM channel from sysfs (write-only).
  
  The PWM channels are numbered using a per-chip index from 0 to npwm-1.
  
  When a PWM channel is exported a pwmX directory will be created in the
  pwmchipN directory it is associated with, where X is the number of the
  channel that was exported. The following properties will then be available:
  
    period
      The total period of the PWM signal (read/write).
      Value is in nanoseconds and is the sum of the active and inactive
      time of the PWM.
  
    duty_cycle
      The active time of the PWM signal (read/write).
      Value is in nanoseconds and must be less than the period.
  
    polarity
      Changes the polarity of the PWM signal (read/write).
      Writes to this property only work if the PWM chip supports changing
      the polarity. The polarity can only be changed if the PWM is not
      enabled. Value is the string "normal" or "inversed".
  
    enable
      Enable/disable the PWM signal (read/write).
  
  	- 0 - disabled
  	- 1 - enabled
  
  Implementing a PWM driver
  -------------------------
  
  Currently there are two ways to implement pwm drivers. Traditionally
  there only has been the barebone API meaning that each driver has
  to implement the pwm_*() functions itself. This means that it's impossible
  to have multiple PWM drivers in the system. For this reason it's mandatory
  for new drivers to use the generic PWM framework.
  
  A new PWM controller/chip can be added using pwmchip_add() and removed
  again with pwmchip_remove(). pwmchip_add() takes a filled in struct
  pwm_chip as argument which provides a description of the PWM chip, the
  number of PWM devices provided by the chip and the chip-specific
  implementation of the supported PWM operations to the framework.
  
  When implementing polarity support in a PWM driver, make sure to respect the
  signal conventions in the PWM framework. By definition, normal polarity
  characterizes a signal starts high for the duration of the duty cycle and
  goes low for the remainder of the period. Conversely, a signal with inversed
  polarity starts low for the duration of the duty cycle and goes high for the
  remainder of the period.
  
  Drivers are encouraged to implement ->apply() instead of the legacy
  ->enable(), ->disable() and ->config() methods. Doing that should provide
  atomicity in the PWM config workflow, which is required when the PWM controls
  a critical device (like a regulator).
  
  The implementation of ->get_state() (a method used to retrieve initial PWM
  state) is also encouraged for the same reason: letting the PWM user know
  about the current PWM state would allow him to avoid glitches.
  
  Locking
  -------
  
  The PWM core list manipulations are protected by a mutex, so pwm_request()
  and pwm_free() may not be called from an atomic context. Currently the
  PWM core does not enforce any locking to pwm_enable(), pwm_disable() and
  pwm_config(), so the calling context is currently driver specific. This
  is an issue derived from the former barebone API and should be fixed soon.
  
  Helpers
  -------
  
  Currently a PWM can only be configured with period_ns and duty_ns. For several
  use cases freq_hz and duty_percent might be better. Instead of calculating
  this in your driver please consider adding appropriate helpers to the framework.