Blame view
Documentation/pci-error-recovery.txt
17.7 KB
065c63590 [PATCH] PCI Error... |
1 2 3 |
PCI Error Recovery ------------------ |
c9ab8b68e [PATCH] Documenta... |
4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 |
February 2, 2006 Current document maintainer: Linas Vepstas <linas@austin.ibm.com> Many PCI bus controllers are able to detect a variety of hardware PCI errors on the bus, such as parity errors on the data and address busses, as well as SERR and PERR errors. Some of the more advanced chipsets are able to deal with these errors; these include PCI-E chipsets, and the PCI-host bridges found on IBM Power4 and Power5-based pSeries boxes. A typical action taken is to disconnect the affected device, halting all I/O to it. The goal of a disconnection is to avoid system corruption; for example, to halt system memory corruption due to DMA's to "wild" addresses. Typically, a reconnection mechanism is also offered, so that the affected PCI device(s) are reset and put back into working condition. The reset phase requires coordination between the affected device drivers and the PCI controller chip. This document describes a generic API for notifying device drivers of a bus disconnection, and then performing error recovery. This API is currently implemented in the 2.6.16 and later kernels. Reporting and recovery is performed in several steps. First, when a PCI hardware error has resulted in a bus disconnect, that event is reported as soon as possible to all affected device drivers, including multiple instances of a device driver on multi-function cards. This allows device drivers to avoid deadlocking in spinloops, waiting for some i/o-space register to change, when it never will. It also gives the drivers a chance to defer incoming I/O as needed. Next, recovery is performed in several stages. Most of the complexity is forced by the need to handle multi-function devices, that is, devices that have multiple device drivers associated with them. In the first stage, each driver is allowed to indicate what type of reset it desires, the choices being a simple re-enabling of I/O or requesting a hard reset (a full electrical #RST of the PCI card). If any driver requests a full reset, that is what will be done. After a full reset and/or a re-enabling of I/O, all drivers are again notified, so that they may then perform any device setup/config that may be required. After these have all completed, a final "resume normal operations" event is sent out. The biggest reason for choosing a kernel-based implementation rather than a user-space implementation was the need to deal with bus disconnects of PCI devices attached to storage media, and, in particular, disconnects from devices holding the root file system. If the root file system is disconnected, a user-space mechanism would have to go through a large number of contortions to complete recovery. Almost all of the current Linux file systems are not tolerant of disconnection from/reconnection to their underlying block device. By contrast, bus errors are easy to manage in the device driver. Indeed, most device drivers already handle very similar recovery procedures; for example, the SCSI-generic layer already provides significant mechanisms for dealing with SCSI bus errors and SCSI bus resets. Detailed Design --------------- Design and implementation details below, based on a chain of public email discussions with Ben Herrenschmidt, circa 5 April 2005. |
065c63590 [PATCH] PCI Error... |
66 67 68 |
The error recovery API support is exposed to the driver in the form of a structure of function pointers pointed to by a new field in struct |
c9ab8b68e [PATCH] Documenta... |
69 70 71 |
pci_driver. A driver that fails to provide the structure is "non-aware", and the actual recovery steps taken are platform dependent. The arch/powerpc implementation will simulate a PCI hotplug remove/add. |
065c63590 [PATCH] PCI Error... |
72 73 |
This structure has the form: |
065c63590 [PATCH] PCI Error... |
74 75 |
struct pci_error_handlers { |
c9ab8b68e [PATCH] Documenta... |
76 |
int (*error_detected)(struct pci_dev *dev, enum pci_channel_state); |
065c63590 [PATCH] PCI Error... |
77 |
int (*mmio_enabled)(struct pci_dev *dev); |
065c63590 [PATCH] PCI Error... |
78 79 |
int (*link_reset)(struct pci_dev *dev); int (*slot_reset)(struct pci_dev *dev); |
c9ab8b68e [PATCH] Documenta... |
80 |
void (*resume)(struct pci_dev *dev); |
065c63590 [PATCH] PCI Error... |
81 |
}; |
c9ab8b68e [PATCH] Documenta... |
82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 |
The possible channel states are: enum pci_channel_state { pci_channel_io_normal, /* I/O channel is in normal state */ pci_channel_io_frozen, /* I/O to channel is blocked */ pci_channel_io_perm_failure, /* PCI card is dead */ }; Possible return values are: enum pci_ers_result { PCI_ERS_RESULT_NONE, /* no result/none/not supported in device driver */ PCI_ERS_RESULT_CAN_RECOVER, /* Device driver can recover without slot reset */ PCI_ERS_RESULT_NEED_RESET, /* Device driver wants slot to be reset. */ PCI_ERS_RESULT_DISCONNECT, /* Device has completely failed, is unrecoverable */ PCI_ERS_RESULT_RECOVERED, /* Device driver is fully recovered and operational */ }; A driver does not have to implement all of these callbacks; however, if it implements any, it must implement error_detected(). If a callback is not implemented, the corresponding feature is considered unsupported. For example, if mmio_enabled() and resume() aren't there, then it is assumed that the driver is not doing any direct recovery and requires |
065c63590 [PATCH] PCI Error... |
103 |
a reset. If link_reset() is not implemented, the card is assumed as |
c9ab8b68e [PATCH] Documenta... |
104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 |
not care about link resets. Typically a driver will want to know about a slot_reset(). The actual steps taken by a platform to recover from a PCI error event will be platform-dependent, but will follow the general sequence described below. STEP 0: Error Event ------------------- PCI bus error is detect by the PCI hardware. On powerpc, the slot is isolated, in that all I/O is blocked: all reads return 0xffffffff, all writes are ignored. STEP 1: Notification -------------------- Platform calls the error_detected() callback on every instance of every driver affected by the error. At this point, the device might not be accessible anymore, depending on the platform (the slot will be isolated on powerpc). The driver may already have "noticed" the error because of a failing I/O, but this is the proper "synchronization point", that is, it gives the driver a chance to cleanup, waiting for pending stuff (timers, whatever, etc...) to complete; it can take semaphores, schedule, etc... everything but touch the device. Within this function and after it returns, the driver |
065c63590 [PATCH] PCI Error... |
130 131 |
shouldn't do any new IOs. Called in task context. This is sort of a "quiesce" point. See note about interrupts at the end of this doc. |
c9ab8b68e [PATCH] Documenta... |
132 133 134 135 |
All drivers participating in this system must implement this call. The driver must return one of the following result codes: - PCI_ERS_RESULT_CAN_RECOVER: Driver returns this if it thinks it might be able to recover |
065c63590 [PATCH] PCI Error... |
136 |
the HW by just banging IOs or if it wants to be given |
c9ab8b68e [PATCH] Documenta... |
137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 |
a chance to extract some diagnostic information (see mmio_enable, below). - PCI_ERS_RESULT_NEED_RESET: Driver returns this if it can't recover without a hard slot reset. - PCI_ERS_RESULT_DISCONNECT: Driver returns this if it doesn't want to recover at all. The next step taken will depend on the result codes returned by the drivers. If all drivers on the segment/slot return PCI_ERS_RESULT_CAN_RECOVER, then the platform should re-enable IOs on the slot (or do nothing in particular, if the platform doesn't isolate slots), and recovery proceeds to STEP 2 (MMIO Enable). If any driver requested a slot reset (by returning PCI_ERS_RESULT_NEED_RESET), then recovery proceeds to STEP 4 (Slot Reset). If the platform is unable to recover the slot, the next step is STEP 6 (Permanent Failure). >>> The current powerpc implementation assumes that a device driver will >>> *not* schedule or semaphore in this routine; the current powerpc |
065c63590 [PATCH] PCI Error... |
161 |
>>> implementation uses one kernel thread to notify all devices; |
c9ab8b68e [PATCH] Documenta... |
162 |
>>> thus, if one device sleeps/schedules, all devices are affected. |
065c63590 [PATCH] PCI Error... |
163 164 165 166 |
>>> Doing better requires complex multi-threaded logic in the error >>> recovery implementation (e.g. waiting for all notification threads >>> to "join" before proceeding with recovery.) This seems excessively >>> complex and not worth implementing. |
c9ab8b68e [PATCH] Documenta... |
167 168 |
>>> The current powerpc implementation doesn't much care if the device >>> attempts I/O at this point, or not. I/O's will fail, returning |
065c63590 [PATCH] PCI Error... |
169 170 171 |
>>> a value of 0xff on read, and writes will be dropped. If the device >>> driver attempts more than 10K I/O's to a frozen adapter, it will >>> assume that the device driver has gone into an infinite loop, and |
c9ab8b68e [PATCH] Documenta... |
172 173 |
>>> it will panic the the kernel. There doesn't seem to be any other >>> way of stopping a device driver that insists on spinning on I/O. |
065c63590 [PATCH] PCI Error... |
174 |
|
c9ab8b68e [PATCH] Documenta... |
175 176 177 178 179 |
STEP 2: MMIO Enabled ------------------- The platform re-enables MMIO to the device (but typically not the DMA), and then calls the mmio_enabled() callback on all affected device drivers. |
065c63590 [PATCH] PCI Error... |
180 |
|
c9ab8b68e [PATCH] Documenta... |
181 |
This is the "early recovery" call. IOs are allowed again, but DMA is |
065c63590 [PATCH] PCI Error... |
182 183 184 185 |
not (hrm... to be discussed, I prefer not), with some restrictions. This is NOT a callback for the driver to start operations again, only to peek/poke at the device, extract diagnostic information, if any, and eventually do things like trigger a device local reset or some such, |
c9ab8b68e [PATCH] Documenta... |
186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 |
but not restart operations. This is callback is made if all drivers on a segment agree that they can try to recover and if no automatic link reset was performed by the HW. If the platform can't just re-enable IOs without a slot reset or a link reset, it wont call this callback, and instead will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset) >>> The following is proposed; no platform implements this yet: >>> Proposal: All I/O's should be done _synchronously_ from within >>> this callback, errors triggered by them will be returned via >>> the normal pci_check_whatever() API, no new error_detected() >>> callback will be issued due to an error happening here. However, >>> such an error might cause IOs to be re-blocked for the whole >>> segment, and thus invalidate the recovery that other devices >>> on the same segment might have done, forcing the whole segment >>> into one of the next states, that is, link reset or slot reset. The driver should return one of the following result codes: - PCI_ERS_RESULT_RECOVERED |
065c63590 [PATCH] PCI Error... |
204 |
Driver returns this if it thinks the device is fully |
c9ab8b68e [PATCH] Documenta... |
205 |
functional and thinks it is ready to start |
065c63590 [PATCH] PCI Error... |
206 207 208 209 210 |
normal driver operations again. There is no guarantee that the driver will actually be allowed to proceed, as another driver on the same segment might have failed and thus triggered a slot reset on platforms that support it. |
c9ab8b68e [PATCH] Documenta... |
211 |
- PCI_ERS_RESULT_NEED_RESET |
065c63590 [PATCH] PCI Error... |
212 213 214 |
Driver returns this if it thinks the device is not recoverable in it's current state and it needs a slot reset to proceed. |
c9ab8b68e [PATCH] Documenta... |
215 |
- PCI_ERS_RESULT_DISCONNECT |
065c63590 [PATCH] PCI Error... |
216 217 |
Same as above. Total failure, no recovery even after reset driver dead. (To be defined more precisely) |
c9ab8b68e [PATCH] Documenta... |
218 219 220 221 222 223 |
The next step taken depends on the results returned by the drivers. If all drivers returned PCI_ERS_RESULT_RECOVERED, then the platform proceeds to either STEP3 (Link Reset) or to STEP 5 (Resume Operations). If any driver returned PCI_ERS_RESULT_NEED_RESET, then the platform proceeds to STEP 4 (Slot Reset) |
065c63590 [PATCH] PCI Error... |
224 |
|
c9ab8b68e [PATCH] Documenta... |
225 |
>>> The current powerpc implementation does not implement this callback. |
065c63590 [PATCH] PCI Error... |
226 |
|
c9ab8b68e [PATCH] Documenta... |
227 228 229 230 231 232 233 234 235 236 237 238 239 240 |
STEP 3: Link Reset ------------------ The platform resets the link, and then calls the link_reset() callback on all affected device drivers. This is a PCI-Express specific state and is done whenever a non-fatal error has been detected that can be "solved" by resetting the link. This call informs the driver of the reset and the driver should check to see if the device appears to be in working condition. The driver is not supposed to restart normal driver I/O operations at this point. It should limit itself to "probing" the device to check it's recoverability status. If all is right, then the platform will call resume() once all drivers have ack'd link_reset(). |
065c63590 [PATCH] PCI Error... |
241 242 |
Result codes: |
c9ab8b68e [PATCH] Documenta... |
243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 |
(identical to STEP 3 (MMIO Enabled) The platform then proceeds to either STEP 4 (Slot Reset) or STEP 5 (Resume Operations). >>> The current powerpc implementation does not implement this callback. STEP 4: Slot Reset ------------------ The platform performs a soft or hard reset of the device, and then calls the slot_reset() callback. A soft reset consists of asserting the adapter #RST line and then restoring the PCI BAR's and PCI configuration header to a state that is equivalent to what it would be after a fresh system power-on followed by power-on BIOS/system firmware initialization. If the platform supports PCI hotplug, then the reset might be performed by toggling the slot electrical power off/on. |
065c63590 [PATCH] PCI Error... |
262 |
|
c9ab8b68e [PATCH] Documenta... |
263 264 265 266 267 |
It is important for the platform to restore the PCI config space to the "fresh poweron" state, rather than the "last state". After a slot reset, the device driver will almost always use its standard device initialization routines, and an unusual config space setup may result in hung devices, kernel panics, or silent data corruption. |
065c63590 [PATCH] PCI Error... |
268 |
|
c9ab8b68e [PATCH] Documenta... |
269 270 271 272 |
This call gives drivers the chance to re-initialize the hardware (re-download firmware, etc.). At this point, the driver may assume that he card is in a fresh state and is fully functional. In particular, interrupt generation should work normally. |
065c63590 [PATCH] PCI Error... |
273 |
|
c9ab8b68e [PATCH] Documenta... |
274 275 276 277 |
Drivers should not yet restart normal I/O processing operations at this point. If all device drivers report success on this callback, the platform will call resume() to complete the sequence, and let the driver restart normal I/O processing. |
065c63590 [PATCH] PCI Error... |
278 279 280 |
A driver can still return a critical failure for this function if it can't get the device operational after reset. If the platform |
c9ab8b68e [PATCH] Documenta... |
281 |
previously tried a soft reset, it might now try a hard reset (power |
065c63590 [PATCH] PCI Error... |
282 283 284 285 |
cycle) and then call slot_reset() again. It the device still can't be recovered, there is nothing more that can be done; the platform will typically report a "permanent failure" in such a case. The device will be considered "dead" in this case. |
c9ab8b68e [PATCH] Documenta... |
286 287 288 289 |
Drivers for multi-function cards will need to coordinate among themselves as to which driver instance will perform any "one-shot" or global device initialization. For example, the Symbios sym53cxx2 driver performs device init only from PCI function 0: |
065c63590 [PATCH] PCI Error... |
290 |
|
c9ab8b68e [PATCH] Documenta... |
291 292 |
+ if (PCI_FUNC(pdev->devfn) == 0) + sym_reset_scsi_bus(np, 0); |
065c63590 [PATCH] PCI Error... |
293 |
|
c9ab8b68e [PATCH] Documenta... |
294 295 296 |
Result codes: - PCI_ERS_RESULT_DISCONNECT Same as above. |
065c63590 [PATCH] PCI Error... |
297 |
|
c9ab8b68e [PATCH] Documenta... |
298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 |
Platform proceeds either to STEP 5 (Resume Operations) or STEP 6 (Permanent Failure). >>> The current powerpc implementation does not currently try a >>> power-cycle reset if the driver returned PCI_ERS_RESULT_DISCONNECT. >>> However, it probably should. STEP 5: Resume Operations ------------------------- The platform will call the resume() callback on all affected device drivers if all drivers on the segment have returned PCI_ERS_RESULT_RECOVERED from one of the 3 previous callbacks. The goal of this callback is to tell the driver to restart activity, that everything is back and running. This callback does not return a result code. At this point, if a new error happens, the platform will restart a new error recovery sequence. STEP 6: Permanent Failure ------------------------- A "permanent failure" has occurred, and the platform cannot recover the device. The platform will call error_detected() with a pci_channel_state value of pci_channel_io_perm_failure. The device driver should, at this point, assume the worst. It should cancel all pending I/O, refuse all new I/O, returning -EIO to higher layers. The device driver should then clean up all of its memory and remove itself from kernel operations, much as it would during system shutdown. The platform will typically notify the system operator of the permanent failure in some way. If the device is hotplug-capable, the operator will probably want to remove and replace the device. Note, however, not all failures are truly "permanent". Some are caused by over-heating, some by a poorly seated card. Many PCI error events are caused by software bugs, e.g. DMA's to wild addresses or bogus split transactions due to programming errors. See the discussion in powerpc/eeh-pci-error-recovery.txt for additional detail on real-life experience of the causes of software errors. Conclusion; General Remarks --------------------------- The way those callbacks are called is platform policy. A platform with no slot reset capability may want to just "ignore" drivers that can't |
065c63590 [PATCH] PCI Error... |
346 347 348 |
recover (disconnect them) and try to let other cards on the same segment recover. Keep in mind that in most real life cases, though, there will be only one driver per segment. |
c9ab8b68e [PATCH] Documenta... |
349 |
Now, a note about interrupts. If you get an interrupt and your |
065c63590 [PATCH] PCI Error... |
350 |
device is dead or has been isolated, there is a problem :) |
c9ab8b68e [PATCH] Documenta... |
351 352 |
The current policy is to turn this into a platform policy. That is, the recovery API only requires that: |
065c63590 [PATCH] PCI Error... |
353 354 355 |
- There is no guarantee that interrupt delivery can proceed from any device on the segment starting from the error detection and until the |
c9ab8b68e [PATCH] Documenta... |
356 |
resume callback is sent, at which point interrupts are expected to be |
065c63590 [PATCH] PCI Error... |
357 |
fully operational. |
c9ab8b68e [PATCH] Documenta... |
358 359 360 |
- There is no guarantee that interrupt delivery is stopped, that is, a driver that gets an interrupt after detecting an error, or that detects an error within the interrupt handler such that it prevents proper |
065c63590 [PATCH] PCI Error... |
361 |
ack'ing of the interrupt (and thus removal of the source) should just |
c9ab8b68e [PATCH] Documenta... |
362 363 |
return IRQ_NOTHANDLED. It's up to the platform to deal with that condition, typically by masking the IRQ source during the duration of |
065c63590 [PATCH] PCI Error... |
364 365 |
the error handling. It is expected that the platform "knows" which interrupts are routed to error-management capable slots and can deal |
c9ab8b68e [PATCH] Documenta... |
366 |
with temporarily disabling that IRQ number during error processing (this |
065c63590 [PATCH] PCI Error... |
367 368 369 370 |
isn't terribly complex). That means some IRQ latency for other devices sharing the interrupt, but there is simply no other way. High end platforms aren't supposed to share interrupts between many devices anyway :) |
c9ab8b68e [PATCH] Documenta... |
371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 |
>>> Implementation details for the powerpc platform are discussed in >>> the file Documentation/powerpc/eeh-pci-error-recovery.txt >>> As of this writing, there are six device drivers with patches >>> implementing error recovery. Not all of these patches are in >>> mainline yet. These may be used as "examples": >>> >>> drivers/scsi/ipr.c >>> drivers/scsi/sym53cxx_2 >>> drivers/next/e100.c >>> drivers/net/e1000 >>> drivers/net/ixgb >>> drivers/net/s2io.c The End ------- |