Blame view
Documentation/hwmon/max6650
2.07 KB
d20620de0 hwmon: New max665... |
1 2 3 4 |
Kernel driver max6650 ===================== Supported chips: |
9c084dae5 hwmon: (max6650) ... |
5 |
* Maxim MAX6650 |
d20620de0 hwmon: New max665... |
6 |
Prefix: 'max6650' |
67b670ff0 hwmon: (max6650) ... |
7 |
Addresses scanned: none |
d20620de0 hwmon: New max665... |
8 |
Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf |
9c084dae5 hwmon: (max6650) ... |
9 10 11 12 |
* Maxim MAX6651 Prefix: 'max6651' Addresses scanned: none Datasheet: http://pdfserv.maxim-ic.com/en/ds/MAX6650-MAX6651.pdf |
d20620de0 hwmon: New max665... |
13 14 |
Authors: |
f99e0e98f Documentation: ch... |
15 |
Hans J. Koch <hjk@hansjkoch.de> |
d20620de0 hwmon: New max665... |
16 17 18 19 20 |
John Morris <john.morris@spirentcom.com> Claus Gindhart <claus.gindhart@kontron.com> Description ----------- |
9c084dae5 hwmon: (max6650) ... |
21 |
This driver implements support for the Maxim MAX6650 and MAX6651. |
d20620de0 hwmon: New max665... |
22 |
|
9c084dae5 hwmon: (max6650) ... |
23 24 |
The 2 devices are very similar, but the MAX6550 has a reduced feature set, e.g. only one fan-input, instead of 4 for the MAX6651. |
d20620de0 hwmon: New max665... |
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 |
The driver is not able to distinguish between the 2 devices. The driver provides the following sensor accesses in sysfs: fan1_input ro fan tachometer speed in RPM fan2_input ro " fan3_input ro " fan4_input ro " fan1_target rw desired fan speed in RPM (closed loop mode only) pwm1_enable rw regulator mode, 0=full on, 1=open loop, 2=closed loop pwm1 rw relative speed (0-255), 255=max. speed. Used in open loop mode only. fan1_div rw sets the speed range the inputs can handle. Legal values are 1, 2, 4, and 8. Use lower values for faster fans. |
67b670ff0 hwmon: (max6650) ... |
41 42 43 44 45 46 |
Usage notes ----------- This driver does not auto-detect devices. You will have to instantiate the devices explicitly. Please see Documentation/i2c/instantiating-devices for details. |
d20620de0 hwmon: New max665... |
47 48 49 50 51 52 53 54 55 56 57 58 59 60 |
Module parameters ----------------- If your board has a BIOS that initializes the MAX6650/6651 correctly, you can simply load your module without parameters. It won't touch the configuration registers then. If your board BIOS doesn't initialize the chip, or you want different settings, you can set the following parameters: voltage_12V: 5=5V fan, 12=12V fan, 0=don't change prescaler: Possible values are 1,2,4,8,16, or 0 for don't change clock: The clock frequency in Hz of the chip the driver should assume [254000] Please have a look at the MAX6650/6651 data sheet and make sure that you fully understand the meaning of these parameters before you attempt to change them. |