#
  # Multimedia Video device configuration
  #

  menuconfig RADIO_ADAPTERS
  	bool "Radio Adapters"

  	depends on VIDEO_V4L2

  	default y

  	---help---
  	  Say Y here to enable selecting AM/FM radio adapters.

  if RADIO_ADAPTERS && VIDEO_V4L2

  config RADIO_SI470X
  	bool "Silicon Labs Si470x FM Radio Receiver support"
  	depends on VIDEO_V4L2
  
  source "drivers/media/radio/si470x/Kconfig"
  
  config USB_MR800
  	tristate "AverMedia MR 800 USB FM radio support"
  	depends on USB && VIDEO_V4L2
  	---help---
  	  Say Y here if you want to connect this type of radio to your
  	  computer's USB port. Note that the audio is not digital, and
  	  you must connect the line out connector to a sound card or a
  	  set of speakers.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-mr800.
  
  config USB_DSBR
  	tristate "D-Link/GemTek USB FM radio support"
  	depends on USB && VIDEO_V4L2
  	---help---
  	  Say Y here if you want to connect this type of radio to your
  	  computer's USB port. Note that the audio is not digital, and
  	  you must connect the line out connector to a sound card or a
  	  set of speakers.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called dsbr100.
  
  config RADIO_MAXIRADIO
  	tristate "Guillemot MAXI Radio FM 2000 radio"
  	depends on VIDEO_V4L2 && PCI
  	---help---
  	  Choose Y here if you have this radio card.  This card may also be
  	  found as Gemtek PCI FM.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-maxiradio.
  
  
  config I2C_SI4713
  	tristate "I2C driver for Silicon Labs Si4713 device"
  	depends on I2C && VIDEO_V4L2
  	---help---
  	  Say Y here if you want support to Si4713 I2C device.
  	  This device driver supports only i2c bus.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called si4713.
  
  config RADIO_SI4713
  	tristate "Silicon Labs Si4713 FM Radio Transmitter support"
  	depends on I2C && VIDEO_V4L2
  	select I2C_SI4713
  	---help---
  	  Say Y here if you want support to Si4713 FM Radio Transmitter.
  	  This device can transmit audio through FM. It can transmit
  	  RDS and RBDS signals as well. This module is the v4l2 radio
  	  interface for the i2c driver of this device.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-si4713.
  
  config RADIO_TEA5764
  	tristate "TEA5764 I2C FM radio support"
  	depends on I2C && VIDEO_V4L2
  	---help---
  	  Say Y here if you want to use the TEA5764 FM chip found in
  	  EZX phones. This FM chip is present in EZX phones from Motorola,
  	  connected to internal pxa I2C bus.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-tea5764.
  
  config RADIO_TEA5764_XTAL
  	bool "TEA5764 crystal reference"
  	depends on RADIO_TEA5764=y
  	default y
  	help
  	  Say Y here if TEA5764 have a 32768 Hz crystal in circuit, say N
  	  here if TEA5764 reference frequency is connected in FREQIN.
  
  config RADIO_SAA7706H
  	tristate "SAA7706H Car Radio DSP"
  	depends on I2C && VIDEO_V4L2
  	---help---
  	  Say Y here if you want to use the SAA7706H Car radio Digital
  	  Signal Processor, found for instance on the Russellville development
  	  board. On the russellville the device is connected to internal
  	  timberdale I2C bus.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called SAA7706H.
  
  config RADIO_TEF6862
  	tristate "TEF6862 Car Radio Enhanced Selectivity Tuner"
  	depends on I2C && VIDEO_V4L2
  	---help---
  	  Say Y here if you want to use the TEF6862 Car Radio Enhanced
  	  Selectivity Tuner, found for instance on the Russellville development
  	  board. On the russellville the device is connected to internal
  	  timberdale I2C bus.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called TEF6862.
  
  config RADIO_TIMBERDALE
  	tristate "Enable the Timberdale radio driver"
  	depends on MFD_TIMBERDALE && VIDEO_V4L2
  	depends on I2C	# for RADIO_SAA7706H
  	select RADIO_TEF6862
  	select RADIO_SAA7706H
  	---help---
  	  This is a kind of umbrella driver for the Radio Tuner and DSP
  	  found behind the Timberdale FPGA on the Russellville board.
  	  Enabling this driver will automatically select the DSP and tuner.
  
  config RADIO_WL1273
  	tristate "Texas Instruments WL1273 I2C FM Radio"
  	depends on I2C && VIDEO_V4L2
  	select MFD_CORE
  	select MFD_WL1273_CORE
  	select FW_LOADER
  	---help---
  	  Choose Y here if you have this FM radio chip.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux 2 API.  Information on
  	  this API and pointers to "v4l2" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-wl1273.
  
  # TI's ST based wl128x FM radio
  source "drivers/media/radio/wl128x/Kconfig"
  
  #
  # ISA drivers configuration
  #
  
  menuconfig V4L_RADIO_ISA_DRIVERS
  	bool "ISA radio devices"
  	depends on ISA
  	default n
  	---help---
  	  Say Y here to enable support for these ISA drivers.
  
  if V4L_RADIO_ISA_DRIVERS

  config RADIO_CADET
  	tristate "ADS Cadet AM/FM Tuner"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have one of these AM/FM radio cards, and then
  	  fill in the port address below.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  Further documentation on this driver can be found on the WWW at
  	  <http://linux.blackhawke.net/cadet/>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-cadet.
  
  config RADIO_RTRACK
  	tristate "AIMSlab RadioTrack (aka RadioReveal) support"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have one of these FM radio cards, and then fill
  	  in the port address below.
  
  	  Note that newer AIMSlab RadioTrack cards have a different chipset
  	  and are not supported by this driver.  For these cards, use the
  	  RadioTrack II driver below.
  
  	  If you have a GemTeks combined (PnP) sound- and radio card you must
  	  use this driver as a module and setup the card with isapnptools.
  	  You must also pass the module a suitable io parameter, 0x248 has
  	  been reported to be used by these cards.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>. More information is
  	  contained in the file
  	  <file:Documentation/video4linux/radiotrack.txt>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-aimslab.
  
  config RADIO_RTRACK_PORT
  	hex "RadioTrack i/o port (0x20f or 0x30f)"
  	depends on RADIO_RTRACK=y
  	default "20f"
  	help
  	  Enter either 0x30f or 0x20f here.  The card default is 0x30f, if you
  	  haven't changed the jumper setting on the card.
  
  config RADIO_RTRACK2
  	tristate "AIMSlab RadioTrack II support"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have this FM radio card, and then fill in the
  	  port address below.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-rtrack2.
  
  config RADIO_RTRACK2_PORT
  	hex "RadioTrack II i/o port (0x20c or 0x30c)"
  	depends on RADIO_RTRACK2=y
  	default "30c"
  	help
  	  Enter either 0x30c or 0x20c here.  The card default is 0x30c, if you
  	  haven't changed the jumper setting on the card.
  
  config RADIO_AZTECH
  	tristate "Aztech/Packard Bell Radio"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have one of these FM radio cards, and then fill
  	  in the port address below.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-aztech.
  
  config RADIO_AZTECH_PORT
  	hex "Aztech/Packard Bell I/O port (0x350 or 0x358)"
  	depends on RADIO_AZTECH=y
  	default "350"
  	help
  	  Enter either 0x350 or 0x358 here.  The card default is 0x350, if you
  	  haven't changed the setting of jumper JP3 on the card.  Removing the
  	  jumper sets the card to 0x358.
  
  config RADIO_GEMTEK

  	tristate "GemTek Radio card (or compatible) support"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have this FM radio card, and then fill in the

  	  I/O port address and settings below. The following cards either have
  	  GemTek Radio tuner or are rebranded GemTek Radio cards:
  
  	  - Sound Vision 16 Gold with FM Radio
  	  - Typhoon Radio card (some models)
  	  - Hama Radio card

  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-gemtek.
  
  config RADIO_GEMTEK_PORT

  	hex "Fixed I/O port (0x20c, 0x30c, 0x24c, 0x34c, 0c24c or 0x28c)"

  	depends on RADIO_GEMTEK=y
  	default "34c"
  	help
  	  Enter either 0x20c, 0x30c, 0x24c or 0x34c here. The card default is
  	  0x34c, if you haven't changed the jumper setting on the card. On
  	  Sound Vision 16 Gold PnP with FM Radio (ESS1869+FM Gemtek), the I/O

  	  port is 0x20c, 0x248 or 0x28c.
  	  If automatic I/O port probing is enabled this port will be used only
  	  in case of automatic probing failure, ie. as a fallback.
  
  config RADIO_GEMTEK_PROBE
  	bool "Automatic I/O port probing"
  	depends on RADIO_GEMTEK=y
  	default y
  	help
  	  Say Y here to enable automatic probing for GemTek Radio card. The
  	  following ports will be probed: 0x20c, 0x30c, 0x24c, 0x34c, 0x248 and
  	  0x28c.

  config RADIO_MIROPCM20
  	tristate "miroSOUND PCM20 radio"

  	depends on ISA && ISA_DMA_API && VIDEO_V4L2 && SND

  	select SND_ISA

  	select SND_MIRO
  	---help---
  	  Choose Y here if you have this FM radio card. You also need to enable
  	  the ALSA sound system. This choice automatically selects the ALSA
  	  sound card driver "Miro miroSOUND PCM1pro/PCM12/PCM20radio" as this
  	  is required for the radio-miropcm20.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-miropcm20.

  config RADIO_SF16FMI

  	tristate "SF16-FMI/SF16-FMP Radio"

  	depends on ISA && VIDEO_V4L2

  	---help---

  	  Choose Y here if you have one of these FM radio cards.

  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-sf16fmi.
  
  config RADIO_SF16FMR2
  	tristate "SF16FMR2 Radio"

  	depends on ISA && VIDEO_V4L2 && SND

  	---help---
  	  Choose Y here if you have one of these FM radio cards.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found on the WWW at
  	  <http://roadrunner.swansea.uk.linux.org/v4l.shtml>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-sf16fmr2.
  
  config RADIO_TERRATEC
  	tristate "TerraTec ActiveRadio ISA Standalone"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have this FM radio card, and then fill in the
  	  port address below. (TODO)
  
  	  Note: This driver is in its early stages.  Right now volume and
  	  frequency control and muting works at least for me, but
  	  unfortunately I have not found anybody who wants to use this card
  	  with Linux.  So if it is this what YOU are trying to do right now,
  	  PLEASE DROP ME A NOTE!!  Rolf Offermanns <rolf@offermanns.de>.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-terratec.
  
  config RADIO_TERRATEC_PORT
  	hex "Terratec i/o port (normally 0x590)"
  	depends on RADIO_TERRATEC=y
  	default "590"
  	help
  	  Fill in the I/O port of your TerraTec FM radio card. If unsure, go
  	  with the default.
  
  config RADIO_TRUST
  	tristate "Trust FM radio card"

  	depends on ISA && VIDEO_V4L2

  	help
  	  This is a driver for the Trust FM radio cards. Say Y if you have
  	  such a card and want to use it under Linux.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-trust.
  
  config RADIO_TRUST_PORT
  	hex "Trust i/o port (usually 0x350 or 0x358)"
  	depends on RADIO_TRUST=y
  	default "350"
  	help
  	  Enter the I/O port of your Trust FM radio card. If unsure, try the
  	  values "0x350" or "0x358".
  
  config RADIO_TYPHOON
  	tristate "Typhoon Radio (a.k.a. EcoRadio)"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have one of these FM radio cards, and then fill
  	  in the port address and the frequency used for muting below.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-typhoon.

  config RADIO_TYPHOON_PORT
  	hex "Typhoon I/O port (0x316 or 0x336)"
  	depends on RADIO_TYPHOON=y
  	default "316"
  	help
  	  Enter the I/O port of your Typhoon or EcoRadio radio card.
  
  config RADIO_TYPHOON_MUTEFREQ
  	int "Typhoon frequency set when muting the device (kHz)"
  	depends on RADIO_TYPHOON=y
  	default "87500"
  	help
  	  Enter the frequency used for muting the radio. The device is never
  	  completely silent. If the volume is just turned down, you can still
  	  hear silent voices and music. For that reason, the frequency of the
  	  radio device is set to the frequency you can enter here whenever
  	  the device is muted. There should be no local radio station at that
  	  frequency.
  
  config RADIO_ZOLTRIX
  	tristate "Zoltrix Radio"

  	depends on ISA && VIDEO_V4L2

  	---help---
  	  Choose Y here if you have one of these FM radio cards, and then fill
  	  in the port address below.
  
  	  In order to control your radio card, you will need to use programs
  	  that are compatible with the Video For Linux API.  Information on
  	  this API and pointers to "v4l" programs may be found at
  	  <file:Documentation/video4linux/API.html>.
  
  	  To compile this driver as a module, choose M here: the
  	  module will be called radio-zoltrix.
  
  config RADIO_ZOLTRIX_PORT
  	hex "ZOLTRIX I/O port (0x20c or 0x30c)"
  	depends on RADIO_ZOLTRIX=y
  	default "20c"
  	help
  	  Enter the I/O port of your Zoltrix radio card.

  endif # V4L_RADIO_ISA_DRIVERS

  endif # RADIO_ADAPTERS