Eric Lee / smarc-fsl-linux-kernel

Blame view

Documentation/btmrvl.txt 2.87 KB
edit raw normal view history
196be0cd0   Bing Zhao   Bluetooth: Add do... 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
 
  =======================================================================
  		README for btmrvl driver
  =======================================================================
  
  
  All commands are used via debugfs interface.
  
  =====================
  Set/get driver configurations:
  
  Path:	/debug/btmrvl/config/
  
  gpiogap=[n]
  hscfgcmd
  	These commands are used to configure the host sleep parameters.
  	bit 8:0  -- Gap
  	bit 16:8 -- GPIO
  
  	where GPIO is the pin number of GPIO used to wake up the host.
  	It could be any valid GPIO pin# (e.g. 0-7) or 0xff (SDIO interface
  	wakeup will be used instead).
  
  	where Gap is the gap in milli seconds between wakeup signal and
  	wakeup event, or 0xff for special host sleep setting.
  
  	Usage:
  		# Use SDIO interface to wake up the host and set GAP to 0x80:
  		echo 0xff80 > /debug/btmrvl/config/gpiogap
  		echo 1 > /debug/btmrvl/config/hscfgcmd
  
  		# Use GPIO pin #3 to wake up the host and set GAP to 0xff:
  		echo 0x03ff >  /debug/btmrvl/config/gpiogap
  		echo 1 > /debug/btmrvl/config/hscfgcmd
  
  psmode=[n]
  pscmd
  	These commands are used to enable/disable auto sleep mode
  
  	where the option is:
  			1 	-- Enable auto sleep mode
  			0 	-- Disable auto sleep mode
  
  	Usage:
  		# Enable auto sleep mode
  		echo 1 > /debug/btmrvl/config/psmode
  		echo 1 > /debug/btmrvl/config/pscmd
  
  		# Disable auto sleep mode
  		echo 0 > /debug/btmrvl/config/psmode
  		echo 1 > /debug/btmrvl/config/pscmd
  
  
  hsmode=[n]
  hscmd
  	These commands are used to enable host sleep or wake up firmware
  
  	where the option is:
  			1	-- Enable host sleep
  			0	-- Wake up firmware
  
  	Usage:
  		# Enable host sleep
  		echo 1 > /debug/btmrvl/config/hsmode
  		echo 1 > /debug/btmrvl/config/hscmd
  
  		# Wake up firmware
  		echo 0 > /debug/btmrvl/config/hsmode
  		echo 1 > /debug/btmrvl/config/hscmd
  
  
  ======================
  Get driver status:
  
  Path:	/debug/btmrvl/status/
  
  Usage:
  	cat /debug/btmrvl/status/<args>
  
  where the args are:
  
  curpsmode
  	This command displays current auto sleep status.
  
  psstate
  	This command display the power save state.
  
  hsstate
  	This command display the host sleep state.
  
  txdnldrdy
  	This command displays the value of Tx download ready flag.
  
  
  =====================
  
  Use hcitool to issue raw hci command, refer to hcitool manual
  
  	Usage: Hcitool cmd <ogf> <ocf> [Parameters]
  
  	Interface Control Command
  	hcitool cmd 0x3f 0x5b 0xf5 0x01 0x00    --Enable All interface
  	hcitool cmd 0x3f 0x5b 0xf5 0x01 0x01    --Enable Wlan interface
  	hcitool cmd 0x3f 0x5b 0xf5 0x01 0x02    --Enable BT interface
  	hcitool cmd 0x3f 0x5b 0xf5 0x00 0x00    --Disable All interface
  	hcitool cmd 0x3f 0x5b 0xf5 0x00 0x01    --Disable Wlan interface
  	hcitool cmd 0x3f 0x5b 0xf5 0x00 0x02    --Disable BT interface
  
  =======================================================================
  
  
  SD8688 firmware:
  
  /lib/firmware/sd8688_helper.bin
  /lib/firmware/sd8688.bin
  
  
  The images can be downloaded from:
  
  git.infradead.org/users/dwmw2/linux-firmware.git/libertas/