07 Nov, 2005
20 commits
-
Add support for "4G Systems MTX-1 Flash device", better known as meshcube.
From: Bruno Randolf
Signed-off-by: Joern Engel
Signed-off-by: Thomas Gleixner -
The changes introduced allow to suspend/resume NAND flash.
A new state (FL_PM_SUSPENDED) is introduced, as well as
routines for mtd->suspend and mtd->resume to put the flash in
suspended state from software pov.Signed-off-by: Vitaly Wool
Signed-off-by: Thomas Gleixner -
From: Vitaly Bordug
Signed-off-by: Todd Poynor
Signed-off-by: Thomas Gleixner -
Now we can use the generic platform driver
Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
- Intel chip driver has a reboot notifier so no need to reset the chip here.
- Don't play with chip selects (platform code should do this if necessary).Signed-off-by: David Vrabel
Signed-off-by: Thomas Gleixner -
Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
- Remove unused block, page parameters
- Add constant instead of runtime valueSigned-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
- Update OMAP OneNAND mapping file using device driver model
- Remove board specific macro and values.Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
Based on NAND memory bad block table code
Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
Add OneNAND Sync. Burst Read support
Tested with OMAP platformSigned-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
OneNAND is a new flash technology from Samsung with integrated SRAM
buffers and logic interface.Signed-off-by: Kyungmin Park
Signed-off-by: Thomas Gleixner -
The bit mask used for oob size calculation was using 2 bits instead
of one. Fortunately the next bit has been 0 all the time.Thanks to Nathan H. for pointing this out
Signed-off-by: Thomas Gleixner
-
Signed-off-by: Thomas Gleixner
-
Signed-off-by: Youssef Hmamouche
Signed-off-by: David Woodhouse
Signed-off-by: Thomas Gleixner -
While this might be useful for all supported flash types, it is mandatory
for proper JFFS2 support with Sibley flash.Signed-off-by: Nicolas Pitre
Signed-off-by: Thomas Gleixner -
This updates the Primary Vendor-Specific Extended Query parsing to
version 1.4 in order to get the information about the Configurable
Programming Mode regions implemented in the Sibley flash, as well as
selecting the appropriate write command code.This flash does not behave like traditional NOR flash when writing data.
While mtdblock should just work, further changes are needed for JFFS2 use.Signed-off-by: Nicolas Pitre
Signed-off-by: Thomas Gleixner -
This includes improved error handling/reporting plus some other
message cleanups.Signed-off-by: Nicolas Pitre
Signed-off-by: Thomas Gleixner -
This type of flash translation layer (FTL) is used by the Embedded BIOS
by General Software. It is known as the Resident Flash Disk (RFD), see:http://www.gensw.com/pages/prod/bios/rfd.htm
Signed-off-by: Sean Young
Signed-off-by: Thomas Gleixner
06 Nov, 2005
1 commit
05 Nov, 2005
9 commits
-
This adds support for the Nvidia Geforce 7800 series of cards to the
nvidiafb framebuffer driver. All it does is add the PCI device id for
the 7800, 7800 GTX, 7800 GO, and 7800 GTX GO cards to the module device
table for the nvidiafb.ko driver, so that nvidiafb.ko will actually work
on these cards.I also added the relevant PCI device ids to linux/pci_ids.h
I tested it on my 7800 GTX here and it works like a charm. I now can
get framebuffer support on this card! Woo hoo!! Nothing like 200x75 text
mode to make your eyes BLEED. ;)Signed-off-by: Linus Torvalds
-
At header fixup time, it is not yet legal to ioremap() PCI
device registers, yet that is what this quirk code needs to
do.Signed-off-by: David S. Miller
-
No longer maintained
-
No longer maintained
-
No longer maintained
04 Nov, 2005
3 commits
-
Make sure that the P_Key index passed into mthca_modify_qp() is
within the device's P_Key table.Signed-off-by: Jack Morgenstein
Signed-off-by: Roland Dreier -
Fix sparse warning about passing `0` to simple_strtoul()
Signed-off-by: Ben Dooks
Signed-off-by: Russell King -
Fix hotplug of devices for ib_umad module: when a device goes away,
kill off all MAD agents for open files associated with that device,
and make sure that the device is not touched again after ib_umad
returns from its remove_one function.Signed-off-by: Roland Dreier
03 Nov, 2005
6 commits
-
Mellanox has decided that the components of the firmware version are
really meant to be displayed in decimal, e.g. 0x000400070190 is
version 4.7.400. Change the format we use from "%x.%x.%x" to
"%d.%d.%d" to match this convention.Signed-off-by: Roland Dreier
-
Don't build ipoib_mcast_iter_ functions if CONFIG_INFINIBAND_IPOIB_DEBUG
is not enabled -- their only callers will not be built either.Also move the prototype for ipoib_open() to ipoib.h to fix a sparse warning.
Signed-off-by: Roland Dreier
-
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator. This driver is
used to talk talk to InfiniBand SRP targets (storage devices).Signed-off-by: Roland Dreier
-
Shrink our source and .text a little by removing a few assignments of
NULL and 0 to memory that is already cleared as part of the allocation.Signed-off-by: Roland Dreier
02 Nov, 2005
1 commit
-
Replace kmalloc()+memset(,0,) with kzalloc(), for a net savings of 35
source lines and about 500 bytes of text.Signed-off-by: Roland Dreier