/* Copyright (c) 2018 The Chromium OS Authors. All rights reserved.

   * Use of this source code is governed by a BSD-style license that can be
   * found in the LICENSE file.
   */
  
  /* Host communication command constants for Chrome EC */
  
  #ifndef __CROS_EC_COMMANDS_H
  #define __CROS_EC_COMMANDS_H
  
  /*
   * Protocol overview
   *
   * request:  CMD [ P0 P1 P2 ... Pn S ]
   * response: ERR [ P0 P1 P2 ... Pn S ]
   *
   * where the bytes are defined as follow :
   *      - CMD is the command code. (defined by EC_CMD_ constants)
   *      - ERR is the error code. (defined by EC_RES_ constants)
   *      - Px is the optional payload.
   *        it is not sent if the error code is not success.
   *        (defined by ec_params_ and ec_response_ structures)
   *      - S is the checksum which is the sum of all payload bytes.
   *
   * On LPC, CMD and ERR are sent/received at EC_LPC_ADDR_KERNEL|USER_CMD
   * and the payloads are sent/received at EC_LPC_ADDR_KERNEL|USER_PARAM.
   * On I2C, all bytes are sent serially in the same message.
   */

  /*
   * Current version of this protocol
   *
   * TODO(crosbug.com/p/11223): This is effectively useless; protocol is
   * determined in other ways.  Remove this once the kernel code no longer
   * depends on it.
   */

  #define EC_PROTO_VERSION          0x00000002
  
  /* Command version mask */
  #define EC_VER_MASK(version) (1UL << (version))
  
  /* I/O addresses for ACPI commands */
  #define EC_LPC_ADDR_ACPI_DATA  0x62
  #define EC_LPC_ADDR_ACPI_CMD   0x66
  
  /* I/O addresses for host command */
  #define EC_LPC_ADDR_HOST_DATA  0x200
  #define EC_LPC_ADDR_HOST_CMD   0x204
  
  /* I/O addresses for host command args and params */

  /* Protocol version 2 */
  #define EC_LPC_ADDR_HOST_ARGS    0x800  /* And 0x801, 0x802, 0x803 */
  #define EC_LPC_ADDR_HOST_PARAM   0x804  /* For version 2 params; size is
  					 * EC_PROTO2_MAX_PARAM_SIZE */
  /* Protocol version 3 */
  #define EC_LPC_ADDR_HOST_PACKET  0x800  /* Offset of version 3 packet */
  #define EC_LPC_HOST_PACKET_SIZE  0x100  /* Max size of version 3 packet */
  
  /* The actual block is 0x800-0x8ff, but some BIOSes think it's 0x880-0x8ff
   * and they tell the kernel that so we have to think of it as two parts. */
  #define EC_HOST_CMD_REGION0    0x800
  #define EC_HOST_CMD_REGION1    0x880
  #define EC_HOST_CMD_REGION_SIZE 0x80

  
  /* EC command register bit functions */
  #define EC_LPC_CMDR_DATA	(1 << 0)  /* Data ready for host to read */
  #define EC_LPC_CMDR_PENDING	(1 << 1)  /* Write pending to EC */
  #define EC_LPC_CMDR_BUSY	(1 << 2)  /* EC is busy processing a command */
  #define EC_LPC_CMDR_CMD		(1 << 3)  /* Last host write was a command */
  #define EC_LPC_CMDR_ACPI_BRST	(1 << 4)  /* Burst mode (not used) */
  #define EC_LPC_CMDR_SCI		(1 << 5)  /* SCI event is pending */
  #define EC_LPC_CMDR_SMI		(1 << 6)  /* SMI event is pending */
  
  #define EC_LPC_ADDR_MEMMAP       0x900
  #define EC_MEMMAP_SIZE         255 /* ACPI IO buffer max is 255 bytes */
  #define EC_MEMMAP_TEXT_MAX     8   /* Size of a string in the memory map */
  
  /* The offset address of each type of data in mapped memory. */

  #define EC_MEMMAP_TEMP_SENSOR      0x00 /* Temp sensors 0x00 - 0x0f */
  #define EC_MEMMAP_FAN              0x10 /* Fan speeds 0x10 - 0x17 */
  #define EC_MEMMAP_TEMP_SENSOR_B    0x18 /* More temp sensors 0x18 - 0x1f */
  #define EC_MEMMAP_ID               0x20 /* 0x20 == 'E', 0x21 == 'C' */

  #define EC_MEMMAP_ID_VERSION       0x22 /* Version of data in 0x20 - 0x2f */
  #define EC_MEMMAP_THERMAL_VERSION  0x23 /* Version of data in 0x00 - 0x1f */
  #define EC_MEMMAP_BATTERY_VERSION  0x24 /* Version of data in 0x40 - 0x7f */
  #define EC_MEMMAP_SWITCHES_VERSION 0x25 /* Version of data in 0x30 - 0x33 */
  #define EC_MEMMAP_EVENTS_VERSION   0x26 /* Version of data in 0x34 - 0x3f */

  #define EC_MEMMAP_HOST_CMD_FLAGS   0x27 /* Host cmd interface flags (8 bits) */
  /* Unused 0x28 - 0x2f */
  #define EC_MEMMAP_SWITCHES         0x30	/* 8 bits */
  /* Unused 0x31 - 0x33 */
  #define EC_MEMMAP_HOST_EVENTS      0x34 /* 32 bits */
  /* Reserve 0x38 - 0x3f for additional host event-related stuff */
  /* Battery values are all 32 bits */

  #define EC_MEMMAP_BATT_VOLT        0x40 /* Battery Present Voltage */
  #define EC_MEMMAP_BATT_RATE        0x44 /* Battery Present Rate */
  #define EC_MEMMAP_BATT_CAP         0x48 /* Battery Remaining Capacity */
  #define EC_MEMMAP_BATT_FLAG        0x4c /* Battery State, defined below */
  #define EC_MEMMAP_BATT_DCAP        0x50 /* Battery Design Capacity */
  #define EC_MEMMAP_BATT_DVLT        0x54 /* Battery Design Voltage */
  #define EC_MEMMAP_BATT_LFCC        0x58 /* Battery Last Full Charge Capacity */
  #define EC_MEMMAP_BATT_CCNT        0x5c /* Battery Cycle Count */

  /* Strings are all 8 bytes (EC_MEMMAP_TEXT_MAX) */

  #define EC_MEMMAP_BATT_MFGR        0x60 /* Battery Manufacturer String */
  #define EC_MEMMAP_BATT_MODEL       0x68 /* Battery Model Number String */
  #define EC_MEMMAP_BATT_SERIAL      0x70 /* Battery Serial Number String */
  #define EC_MEMMAP_BATT_TYPE        0x78 /* Battery Type String */

  #define EC_MEMMAP_ALS              0x80 /* ALS readings in lux (2 X 16 bits) */
  /* Unused 0x84 - 0x8f */
  #define EC_MEMMAP_ACC_STATUS       0x90 /* Accelerometer status (8 bits )*/
  /* Unused 0x91 */
  #define EC_MEMMAP_ACC_DATA         0x92 /* Accelerometers data 0x92 - 0x9f */
  /* 0x92: Lid Angle if available, LID_ANGLE_UNRELIABLE otherwise */
  /* 0x94 - 0x99: 1st Accelerometer */
  /* 0x9a - 0x9f: 2nd Accelerometer */
  #define EC_MEMMAP_GYRO_DATA        0xa0 /* Gyroscope data 0xa0 - 0xa5 */
  /* Unused 0xa6 - 0xdf */
  
  /*
   * ACPI is unable to access memory mapped data at or above this offset due to
   * limitations of the ACPI protocol. Do not place data in the range 0xe0 - 0xfe
   * which might be needed by ACPI.
   */
  #define EC_MEMMAP_NO_ACPI 0xe0
  
  /* Define the format of the accelerometer mapped memory status byte. */
  #define EC_MEMMAP_ACC_STATUS_SAMPLE_ID_MASK  0x0f
  #define EC_MEMMAP_ACC_STATUS_BUSY_BIT        (1 << 4)
  #define EC_MEMMAP_ACC_STATUS_PRESENCE_BIT    (1 << 7)

  
  /* Number of temp sensors at EC_MEMMAP_TEMP_SENSOR */
  #define EC_TEMP_SENSOR_ENTRIES     16
  /*
   * Number of temp sensors at EC_MEMMAP_TEMP_SENSOR_B.
   *
   * Valid only if EC_MEMMAP_THERMAL_VERSION returns >= 2.
   */
  #define EC_TEMP_SENSOR_B_ENTRIES      8

  
  /* Special values for mapped temperature sensors */

  #define EC_TEMP_SENSOR_NOT_PRESENT    0xff
  #define EC_TEMP_SENSOR_ERROR          0xfe
  #define EC_TEMP_SENSOR_NOT_POWERED    0xfd
  #define EC_TEMP_SENSOR_NOT_CALIBRATED 0xfc
  /*
   * The offset of temperature value stored in mapped memory.  This allows
   * reporting a temperature range of 200K to 454K = -73C to 181C.
   */
  #define EC_TEMP_SENSOR_OFFSET      200

  /*
   * Number of ALS readings at EC_MEMMAP_ALS
   */
  #define EC_ALS_ENTRIES             2
  
  /*
   * The default value a temperature sensor will return when it is present but
   * has not been read this boot.  This is a reasonable number to avoid
   * triggering alarms on the host.
   */
  #define EC_TEMP_SENSOR_DEFAULT     (296 - EC_TEMP_SENSOR_OFFSET)

  #define EC_FAN_SPEED_ENTRIES       4       /* Number of fans at EC_MEMMAP_FAN */
  #define EC_FAN_SPEED_NOT_PRESENT   0xffff  /* Entry not present */
  #define EC_FAN_SPEED_STALLED       0xfffe  /* Fan stalled */
  
  /* Battery bit flags at EC_MEMMAP_BATT_FLAG. */
  #define EC_BATT_FLAG_AC_PRESENT   0x01
  #define EC_BATT_FLAG_BATT_PRESENT 0x02
  #define EC_BATT_FLAG_DISCHARGING  0x04
  #define EC_BATT_FLAG_CHARGING     0x08
  #define EC_BATT_FLAG_LEVEL_CRITICAL 0x10
  
  /* Switch flags at EC_MEMMAP_SWITCHES */
  #define EC_SWITCH_LID_OPEN               0x01
  #define EC_SWITCH_POWER_BUTTON_PRESSED   0x02
  #define EC_SWITCH_WRITE_PROTECT_DISABLED 0x04

  /* Was recovery requested via keyboard; now unused. */
  #define EC_SWITCH_IGNORE1		 0x08

  /* Recovery requested via dedicated signal (from servo board) */
  #define EC_SWITCH_DEDICATED_RECOVERY     0x10
  /* Was fake developer mode switch; now unused.  Remove in next refactor. */
  #define EC_SWITCH_IGNORE0                0x20
  
  /* Host command interface flags */
  /* Host command interface supports LPC args (LPC interface only) */
  #define EC_HOST_CMD_FLAG_LPC_ARGS_SUPPORTED  0x01

  /* Host command interface supports version 3 protocol */
  #define EC_HOST_CMD_FLAG_VERSION_3   0x02

  
  /* Wireless switch flags */

  #define EC_WIRELESS_SWITCH_ALL       ~0x00  /* All flags */
  #define EC_WIRELESS_SWITCH_WLAN       0x01  /* WLAN radio */
  #define EC_WIRELESS_SWITCH_BLUETOOTH  0x02  /* Bluetooth radio */
  #define EC_WIRELESS_SWITCH_WWAN       0x04  /* WWAN power */
  #define EC_WIRELESS_SWITCH_WLAN_POWER 0x08  /* WLAN power */
  
  /*****************************************************************************/
  /*
   * ACPI commands
   *
   * These are valid ONLY on the ACPI command/data port.
   */
  
  /*
   * ACPI Read Embedded Controller
   *
   * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
   *
   * Use the following sequence:
   *
   *    - Write EC_CMD_ACPI_READ to EC_LPC_ADDR_ACPI_CMD
   *    - Wait for EC_LPC_CMDR_PENDING bit to clear
   *    - Write address to EC_LPC_ADDR_ACPI_DATA
   *    - Wait for EC_LPC_CMDR_DATA bit to set
   *    - Read value from EC_LPC_ADDR_ACPI_DATA
   */
  #define EC_CMD_ACPI_READ 0x0080
  
  /*
   * ACPI Write Embedded Controller
   *
   * This reads from ACPI memory space on the EC (EC_ACPI_MEM_*).
   *
   * Use the following sequence:
   *
   *    - Write EC_CMD_ACPI_WRITE to EC_LPC_ADDR_ACPI_CMD
   *    - Wait for EC_LPC_CMDR_PENDING bit to clear
   *    - Write address to EC_LPC_ADDR_ACPI_DATA
   *    - Wait for EC_LPC_CMDR_PENDING bit to clear
   *    - Write value to EC_LPC_ADDR_ACPI_DATA
   */
  #define EC_CMD_ACPI_WRITE 0x0081
  
  /*
   * ACPI Burst Enable Embedded Controller
   *
   * This enables burst mode on the EC to allow the host to issue several
   * commands back-to-back. While in this mode, writes to mapped multi-byte
   * data are locked out to ensure data consistency.
   */
  #define EC_CMD_ACPI_BURST_ENABLE 0x0082
  
  /*
   * ACPI Burst Disable Embedded Controller
   *
   * This disables burst mode on the EC and stops preventing EC writes to mapped
   * multi-byte data.
   */
  #define EC_CMD_ACPI_BURST_DISABLE 0x0083
  
  /*
   * ACPI Query Embedded Controller
   *
   * This clears the lowest-order bit in the currently pending host events, and
   * sets the result code to the 1-based index of the bit (event 0x00000001 = 1,
   * event 0x80000000 = 32), or 0 if no event was pending.
   */
  #define EC_CMD_ACPI_QUERY_EVENT 0x0084
  
  /* Valid addresses in ACPI memory space, for read/write commands */
  
  /* Memory space version; set to EC_ACPI_MEM_VERSION_CURRENT */
  #define EC_ACPI_MEM_VERSION            0x00
  /*
   * Test location; writing value here updates test compliment byte to (0xff -
   * value).
   */
  #define EC_ACPI_MEM_TEST               0x01
  /* Test compliment; writes here are ignored. */
  #define EC_ACPI_MEM_TEST_COMPLIMENT    0x02
  
  /* Keyboard backlight brightness percent (0 - 100) */
  #define EC_ACPI_MEM_KEYBOARD_BACKLIGHT 0x03
  /* DPTF Target Fan Duty (0-100, 0xff for auto/none) */
  #define EC_ACPI_MEM_FAN_DUTY           0x04
  
  /*
   * DPTF temp thresholds. Any of the EC's temp sensors can have up to two
   * independent thresholds attached to them. The current value of the ID
   * register determines which sensor is affected by the THRESHOLD and COMMIT
   * registers. The THRESHOLD register uses the same EC_TEMP_SENSOR_OFFSET scheme
   * as the memory-mapped sensors. The COMMIT register applies those settings.
   *
   * The spec does not mandate any way to read back the threshold settings
   * themselves, but when a threshold is crossed the AP needs a way to determine
   * which sensor(s) are responsible. Each reading of the ID register clears and
   * returns one sensor ID that has crossed one of its threshold (in either
   * direction) since the last read. A value of 0xFF means "no new thresholds
   * have tripped". Setting or enabling the thresholds for a sensor will clear
   * the unread event count for that sensor.
   */
  #define EC_ACPI_MEM_TEMP_ID            0x05
  #define EC_ACPI_MEM_TEMP_THRESHOLD     0x06
  #define EC_ACPI_MEM_TEMP_COMMIT        0x07
  /*
   * Here are the bits for the COMMIT register:
   *   bit 0 selects the threshold index for the chosen sensor (0/1)
   *   bit 1 enables/disables the selected threshold (0 = off, 1 = on)
   * Each write to the commit register affects one threshold.
   */
  #define EC_ACPI_MEM_TEMP_COMMIT_SELECT_MASK (1 << 0)
  #define EC_ACPI_MEM_TEMP_COMMIT_ENABLE_MASK (1 << 1)
  /*
   * Example:
   *
   * Set the thresholds for sensor 2 to 50 C and 60 C:
   *   write 2 to [0x05]      --  select temp sensor 2
   *   write 0x7b to [0x06]   --  C_TO_K(50) - EC_TEMP_SENSOR_OFFSET
   *   write 0x2 to [0x07]    --  enable threshold 0 with this value
   *   write 0x85 to [0x06]   --  C_TO_K(60) - EC_TEMP_SENSOR_OFFSET
   *   write 0x3 to [0x07]    --  enable threshold 1 with this value
   *
   * Disable the 60 C threshold, leaving the 50 C threshold unchanged:
   *   write 2 to [0x05]      --  select temp sensor 2
   *   write 0x1 to [0x07]    --  disable threshold 1
   */
  
  /* DPTF battery charging current limit */
  #define EC_ACPI_MEM_CHARGING_LIMIT     0x08
  
  /* Charging limit is specified in 64 mA steps */
  #define EC_ACPI_MEM_CHARGING_LIMIT_STEP_MA   64
  /* Value to disable DPTF battery charging limit */
  #define EC_ACPI_MEM_CHARGING_LIMIT_DISABLED  0xff
  
  /*
   * Report device orientation
   *   bit 0 device is tablet mode
   */
  #define EC_ACPI_MEM_DEVICE_ORIENTATION 0x09
  #define EC_ACPI_MEM_DEVICE_TABLET_MODE 0x01
  
  /*
   * ACPI addresses 0x20 - 0xff map to EC_MEMMAP offset 0x00 - 0xdf.  This data
   * is read-only from the AP.  Added in EC_ACPI_MEM_VERSION 2.
   */
  #define EC_ACPI_MEM_MAPPED_BEGIN   0x20
  #define EC_ACPI_MEM_MAPPED_SIZE    0xe0
  
  /* Current version of ACPI memory address space */
  #define EC_ACPI_MEM_VERSION_CURRENT 2

  
  /*
   * This header file is used in coreboot both in C and ACPI code.  The ACPI code
   * is pre-processed to handle constants but the ASL compiler is unable to
   * handle actual C code so keep it separate.
   */
  #ifndef __ACPI__
  
  /*
   * Define __packed if someone hasn't beat us to it.  Linux kernel style
   * checking prefers __packed over __attribute__((packed)).
   */
  #ifndef __packed
  #define __packed __attribute__((packed))
  #endif

  #ifndef __aligned
  #define __aligned(x) __attribute__((aligned(x)))
  #endif
  
  /*
   * Attributes for EC request and response packets.  Just defining __packed
   * results in inefficient assembly code on ARM, if the structure is actually
   * 32-bit aligned, as it should be for all buffers.
   *
   * Be very careful when adding these to existing structures.  They will round
   * up the structure size to the specified boundary.
   *
   * Also be very careful to make that if a structure is included in some other
   * parent structure that the alignment will still be true given the packing of
   * the parent structure.  This is particularly important if the sub-structure
   * will be passed as a pointer to another function, since that function will
   * not know about the misaligment caused by the parent structure's packing.
   *
   * Also be very careful using __packed - particularly when nesting non-packed
   * structures inside packed ones.  In fact, DO NOT use __packed directly;
   * always use one of these attributes.
   *
   * Once everything is annotated properly, the following search strings should
   * not return ANY matches in this file other than right here:
   *
   * "__packed" - generates inefficient code; all sub-structs must also be packed
   *
   * "struct [^_]" - all structs should be annotated, except for structs that are
   * members of other structs/unions (and their original declarations should be
   * annotated).
   */
  #ifdef CONFIG_HOSTCMD_ALIGNED
  
  /*
   * Packed structures where offset and size are always aligned to 1, 2, or 4
   * byte boundary.
   */
  #define __ec_align1 __packed
  #define __ec_align2 __packed __aligned(2)
  #define __ec_align4 __packed __aligned(4)
  
  /*
   * Packed structure which must be under-aligned, because its size is not a
   * 4-byte multiple.  This is sub-optimal because it forces byte-wise access
   * of all multi-byte fields in it, even though they are themselves aligned.
   *
   * In theory, we could duplicate the structure with __aligned(4) for accessing
   * its members, but use the __packed version for sizeof().
   */
  #define __ec_align_size1 __packed
  
  /*
   * Packed structure which must be under-aligned, because its offset inside a
   * parent structure is not a 4-byte multiple.
   */
  #define __ec_align_offset1 __packed
  #define __ec_align_offset2 __packed __aligned(2)
  
  /*
   * Structures which are complicated enough that I'm skipping them on the first
   * pass.  They are effectively unchanged from their previous definitions.
   *
   * TODO(rspangler): Figure out what to do with these.  It's likely necessary
   * to work out the size and offset of each member and add explicit padding to
   * maintain those.
   */
  #define __ec_todo_packed __packed
  #define __ec_todo_unpacked
  
  #else  /* !CONFIG_HOSTCMD_ALIGNED */
  
  /*
   * Packed structures make no assumption about alignment, so they do inefficient
   * byte-wise reads.
   */
  #define __ec_align1 __packed
  #define __ec_align2 __packed
  #define __ec_align4 __packed
  #define __ec_align_size1 __packed
  #define __ec_align_offset1 __packed
  #define __ec_align_offset2 __packed
  #define __ec_todo_packed __packed
  #define __ec_todo_unpacked
  
  #endif  /* !CONFIG_HOSTCMD_ALIGNED */

  /* LPC command status byte masks */
  /* EC has written a byte in the data register and host hasn't read it yet */
  #define EC_LPC_STATUS_TO_HOST     0x01
  /* Host has written a command/data byte and the EC hasn't read it yet */
  #define EC_LPC_STATUS_FROM_HOST   0x02
  /* EC is processing a command */
  #define EC_LPC_STATUS_PROCESSING  0x04
  /* Last write to EC was a command, not data */
  #define EC_LPC_STATUS_LAST_CMD    0x08

  /* EC is in burst mode */

  #define EC_LPC_STATUS_BURST_MODE  0x10
  /* SCI event is pending (requesting SCI query) */
  #define EC_LPC_STATUS_SCI_PENDING 0x20
  /* SMI event is pending (requesting SMI query) */
  #define EC_LPC_STATUS_SMI_PENDING 0x40
  /* (reserved) */
  #define EC_LPC_STATUS_RESERVED    0x80
  
  /*
   * EC is busy.  This covers both the EC processing a command, and the host has
   * written a new command but the EC hasn't picked it up yet.
   */
  #define EC_LPC_STATUS_BUSY_MASK \
  	(EC_LPC_STATUS_FROM_HOST | EC_LPC_STATUS_PROCESSING)

  /* Host command response codes (16-bit).  Note that response codes should be
   * stored in a uint16_t rather than directly in a value of this type.
   */

  enum ec_status {
  	EC_RES_SUCCESS = 0,
  	EC_RES_INVALID_COMMAND = 1,
  	EC_RES_ERROR = 2,
  	EC_RES_INVALID_PARAM = 3,
  	EC_RES_ACCESS_DENIED = 4,
  	EC_RES_INVALID_RESPONSE = 5,
  	EC_RES_INVALID_VERSION = 6,
  	EC_RES_INVALID_CHECKSUM = 7,
  	EC_RES_IN_PROGRESS = 8,		/* Accepted, command in progress */
  	EC_RES_UNAVAILABLE = 9,		/* No response available */
  	EC_RES_TIMEOUT = 10,		/* We got a timeout */
  	EC_RES_OVERFLOW = 11,		/* Table / data overflow */

  	EC_RES_INVALID_HEADER = 12,     /* Header contains invalid data */
  	EC_RES_REQUEST_TRUNCATED = 13,  /* Didn't get the entire request */

  	EC_RES_RESPONSE_TOO_BIG = 14,   /* Response was too big to handle */
  	EC_RES_BUS_ERROR = 15,		/* Communications bus error */
  	EC_RES_BUSY = 16		/* Up but too busy.  Should retry */

  };
  
  /*
   * Host event codes.  Note these are 1-based, not 0-based, because ACPI query
   * EC command uses code 0 to mean "no event pending".  We explicitly specify
   * each value in the enum listing so they won't change if we delete/insert an
   * item or rearrange the list (it needs to be stable across platforms, not
   * just within a single compiled instance).
   */
  enum host_event_code {
  	EC_HOST_EVENT_LID_CLOSED = 1,
  	EC_HOST_EVENT_LID_OPEN = 2,
  	EC_HOST_EVENT_POWER_BUTTON = 3,
  	EC_HOST_EVENT_AC_CONNECTED = 4,
  	EC_HOST_EVENT_AC_DISCONNECTED = 5,
  	EC_HOST_EVENT_BATTERY_LOW = 6,
  	EC_HOST_EVENT_BATTERY_CRITICAL = 7,
  	EC_HOST_EVENT_BATTERY = 8,
  	EC_HOST_EVENT_THERMAL_THRESHOLD = 9,

  	/* Event generated by a device attached to the EC */
  	EC_HOST_EVENT_DEVICE = 10,

  	EC_HOST_EVENT_THERMAL = 11,
  	EC_HOST_EVENT_USB_CHARGER = 12,
  	EC_HOST_EVENT_KEY_PRESSED = 13,
  	/*
  	 * EC has finished initializing the host interface.  The host can check
  	 * for this event following sending a EC_CMD_REBOOT_EC command to
  	 * determine when the EC is ready to accept subsequent commands.
  	 */
  	EC_HOST_EVENT_INTERFACE_READY = 14,
  	/* Keyboard recovery combo has been pressed */
  	EC_HOST_EVENT_KEYBOARD_RECOVERY = 15,
  
  	/* Shutdown due to thermal overload */
  	EC_HOST_EVENT_THERMAL_SHUTDOWN = 16,
  	/* Shutdown due to battery level too low */
  	EC_HOST_EVENT_BATTERY_SHUTDOWN = 17,

  	/* Suggest that the AP throttle itself */
  	EC_HOST_EVENT_THROTTLE_START = 18,
  	/* Suggest that the AP resume normal speed */
  	EC_HOST_EVENT_THROTTLE_STOP = 19,
  
  	/* Hang detect logic detected a hang and host event timeout expired */
  	EC_HOST_EVENT_HANG_DETECT = 20,
  	/* Hang detect logic detected a hang and warm rebooted the AP */
  	EC_HOST_EVENT_HANG_REBOOT = 21,
  
  	/* PD MCU triggering host event */
  	EC_HOST_EVENT_PD_MCU = 22,
  
  	/* Battery Status flags have changed */
  	EC_HOST_EVENT_BATTERY_STATUS = 23,
  
  	/* EC encountered a panic, triggering a reset */
  	EC_HOST_EVENT_PANIC = 24,
  
  	/* Keyboard fastboot combo has been pressed */
  	EC_HOST_EVENT_KEYBOARD_FASTBOOT = 25,
  
  	/* EC RTC event occurred */
  	EC_HOST_EVENT_RTC = 26,
  
  	/* Emulate MKBP event */
  	EC_HOST_EVENT_MKBP = 27,
  
  	/* EC desires to change state of host-controlled USB mux */
  	EC_HOST_EVENT_USB_MUX = 28,
  
  	/* TABLET/LAPTOP mode event*/
  	EC_HOST_EVENT_MODE_CHANGE = 29,
  
  	/* Keyboard recovery combo with hardware reinitialization */
  	EC_HOST_EVENT_KEYBOARD_RECOVERY_HW_REINIT = 30,
  
  	/*
  	 * Reserve this last bit to indicate that at least one bit in a
  	 * secondary host event word is set.  See crbug.com/633646.
  	 */
  	EC_HOST_EVENT_EXTENDED = 31,

  	/*
  	 * The high bit of the event mask is not used as a host event code.  If
  	 * it reads back as set, then the entire event mask should be
  	 * considered invalid by the host.  This can happen when reading the
  	 * raw event status via EC_MEMMAP_HOST_EVENTS but the LPC interface is
  	 * not initialized on the EC, or improperly configured on the host.
  	 */
  	EC_HOST_EVENT_INVALID = 32
  };
  /* Host event mask */

  #define EC_HOST_EVENT_MASK(event_code) (1ULL << ((event_code) - 1))

  
  /* Arguments at EC_LPC_ADDR_HOST_ARGS */

  struct __ec_align4 ec_lpc_host_args {

  	uint8_t flags;
  	uint8_t command_version;
  	uint8_t data_size;
  	/*
  	 * Checksum; sum of command + flags + command_version + data_size +
  	 * all params/response data bytes.
  	 */
  	uint8_t checksum;

  };

  
  /* Flags for ec_lpc_host_args.flags */
  /*
   * Args are from host.  Data area at EC_LPC_ADDR_HOST_PARAM contains command
   * params.
   *
   * If EC gets a command and this flag is not set, this is an old-style command.
   * Command version is 0 and params from host are at EC_LPC_ADDR_OLD_PARAM with
   * unknown length.  EC must respond with an old-style response (that is,

   * without setting EC_HOST_ARGS_FLAG_TO_HOST).

   */
  #define EC_HOST_ARGS_FLAG_FROM_HOST 0x01
  /*
   * Args are from EC.  Data area at EC_LPC_ADDR_HOST_PARAM contains response.
   *
   * If EC responds to a command and this flag is not set, this is an old-style
   * response.  Command version is 0 and response data from EC is at
   * EC_LPC_ADDR_OLD_PARAM with unknown length.
   */
  #define EC_HOST_ARGS_FLAG_TO_HOST   0x02

  /*****************************************************************************/

  /*
   * Byte codes returned by EC over SPI interface.
   *
   * These can be used by the AP to debug the EC interface, and to determine
   * when the EC is not in a state where it will ever get around to responding
   * to the AP.
   *
   * Example of sequence of bytes read from EC for a current good transfer:
   *   1. -                  - AP asserts chip select (CS#)
   *   2. EC_SPI_OLD_READY   - AP sends first byte(s) of request
   *   3. -                  - EC starts handling CS# interrupt
   *   4. EC_SPI_RECEIVING   - AP sends remaining byte(s) of request
   *   5. EC_SPI_PROCESSING  - EC starts processing request; AP is clocking in
   *                           bytes looking for EC_SPI_FRAME_START
   *   6. -                  - EC finishes processing and sets up response
   *   7. EC_SPI_FRAME_START - AP reads frame byte
   *   8. (response packet)  - AP reads response packet
   *   9. EC_SPI_PAST_END    - Any additional bytes read by AP
   *   10 -                  - AP deasserts chip select
   *   11 -                  - EC processes CS# interrupt and sets up DMA for
   *                           next request
   *
   * If the AP is waiting for EC_SPI_FRAME_START and sees any value other than
   * the following byte values:
   *   EC_SPI_OLD_READY
   *   EC_SPI_RX_READY
   *   EC_SPI_RECEIVING
   *   EC_SPI_PROCESSING
   *
   * Then the EC found an error in the request, or was not ready for the request
   * and lost data.  The AP should give up waiting for EC_SPI_FRAME_START,
   * because the EC is unable to tell when the AP is done sending its request.
   */
  
  /*
   * Framing byte which precedes a response packet from the EC.  After sending a
   * request, the AP will clock in bytes until it sees the framing byte, then
   * clock in the response packet.
   */
  #define EC_SPI_FRAME_START    0xec
  
  /*
   * Padding bytes which are clocked out after the end of a response packet.
   */
  #define EC_SPI_PAST_END       0xed
  
  /*
   * EC is ready to receive, and has ignored the byte sent by the AP.  EC expects
   * that the AP will send a valid packet header (starting with
   * EC_COMMAND_PROTOCOL_3) in the next 32 bytes.
   */
  #define EC_SPI_RX_READY       0xf8
  
  /*
   * EC has started receiving the request from the AP, but hasn't started
   * processing it yet.
   */
  #define EC_SPI_RECEIVING      0xf9
  
  /* EC has received the entire request from the AP and is processing it. */
  #define EC_SPI_PROCESSING     0xfa
  
  /*
   * EC received bad data from the AP, such as a packet header with an invalid
   * length.  EC will ignore all data until chip select deasserts.
   */
  #define EC_SPI_RX_BAD_DATA    0xfb
  
  /*
   * EC received data from the AP before it was ready.  That is, the AP asserted
   * chip select and started clocking data before the EC was ready to receive it.
   * EC will ignore all data until chip select deasserts.
   */
  #define EC_SPI_NOT_READY      0xfc
  
  /*
   * EC was ready to receive a request from the AP.  EC has treated the byte sent
   * by the AP as part of a request packet, or (for old-style ECs) is processing
   * a fully received packet but is not ready to respond yet.
   */
  #define EC_SPI_OLD_READY      0xfd
  
  /*****************************************************************************/

  
  /*
   * Protocol version 2 for I2C and SPI send a request this way:
   *
   *	0	EC_CMD_VERSION0 + (command version)
   *	1	Command number
   *	2	Length of params = N
   *	3..N+2	Params, if any
   *	N+3	8-bit checksum of bytes 0..N+2
   *
   * The corresponding response is:
   *
   *	0	Result code (EC_RES_*)
   *	1	Length of params = M
   *	2..M+1	Params, if any
   *	M+2	8-bit checksum of bytes 0..M+1
   */
  #define EC_PROTO2_REQUEST_HEADER_BYTES 3
  #define EC_PROTO2_REQUEST_TRAILER_BYTES 1
  #define EC_PROTO2_REQUEST_OVERHEAD (EC_PROTO2_REQUEST_HEADER_BYTES +	\
  				    EC_PROTO2_REQUEST_TRAILER_BYTES)
  
  #define EC_PROTO2_RESPONSE_HEADER_BYTES 2
  #define EC_PROTO2_RESPONSE_TRAILER_BYTES 1
  #define EC_PROTO2_RESPONSE_OVERHEAD (EC_PROTO2_RESPONSE_HEADER_BYTES +	\
  				     EC_PROTO2_RESPONSE_TRAILER_BYTES)
  
  /* Parameter length was limited by the LPC interface */
  #define EC_PROTO2_MAX_PARAM_SIZE 0xfc
  
  /* Maximum request and response packet sizes for protocol version 2 */
  #define EC_PROTO2_MAX_REQUEST_SIZE (EC_PROTO2_REQUEST_OVERHEAD +	\
  				    EC_PROTO2_MAX_PARAM_SIZE)
  #define EC_PROTO2_MAX_RESPONSE_SIZE (EC_PROTO2_RESPONSE_OVERHEAD +	\
  				     EC_PROTO2_MAX_PARAM_SIZE)
  
  /*****************************************************************************/
  
  /*
   * Value written to legacy command port / prefix byte to indicate protocol
   * 3+ structs are being used.  Usage is bus-dependent.
   */
  #define EC_COMMAND_PROTOCOL_3 0xda
  
  #define EC_HOST_REQUEST_VERSION 3
  
  /* Version 3 request from host */

  struct __ec_align4 ec_host_request {
  	/* Structure version (=3)

  	 *
  	 * EC will return EC_RES_INVALID_HEADER if it receives a header with a
  	 * version it doesn't know how to parse.
  	 */
  	uint8_t struct_version;
  
  	/*
  	 * Checksum of request and data; sum of all bytes including checksum
  	 * should total to 0.
  	 */
  	uint8_t checksum;
  
  	/* Command code */
  	uint16_t command;
  
  	/* Command version */
  	uint8_t command_version;
  
  	/* Unused byte in current protocol version; set to 0 */
  	uint8_t reserved;
  
  	/* Length of data which follows this header */
  	uint16_t data_len;

  };

  
  #define EC_HOST_RESPONSE_VERSION 3
  
  /* Version 3 response from EC */

  struct __ec_align4 ec_host_response {
  	/* Structure version (=3) */

  	uint8_t struct_version;
  
  	/*
  	 * Checksum of response and data; sum of all bytes including checksum
  	 * should total to 0.
  	 */
  	uint8_t checksum;
  
  	/* Result code (EC_RES_*) */
  	uint16_t result;
  
  	/* Length of data which follows this header */
  	uint16_t data_len;
  
  	/* Unused bytes in current protocol version; set to 0 */
  	uint16_t reserved;

  };

  
  /*****************************************************************************/

  /*
   * Notes on commands:
   *

   * Each command is an 16-bit command value.  Commands which take params or
   * return response data specify structures for that data.  If no structure is

   * specified, the command does not input or output data, respectively.
   * Parameter/response length is implicit in the structs.  Some underlying
   * communication protocols (I2C, SPI) may add length or checksum headers, but
   * those are implementation-dependent and not defined here.

   *
   * All commands MUST be #defined to be 4-digit UPPER CASE hex values
   * (e.g., 0x00AB, not 0xab) for CONFIG_HOSTCMD_SECTION_SORTED to work.

   */
  
  /*****************************************************************************/
  /* General / test commands */
  
  /*
   * Get protocol version, used to deal with non-backward compatible protocol
   * changes.
   */

  #define EC_CMD_PROTO_VERSION 0x0000

  struct __ec_align4 ec_response_proto_version {

  	uint32_t version;

  };

  
  /*
   * Hello.  This is a simple command to test the EC is responsive to
   * commands.
   */

  #define EC_CMD_HELLO 0x0001

  struct __ec_align4 ec_params_hello {

  	uint32_t in_data;  /* Pass anything here */

  };

  struct __ec_align4 ec_response_hello {

  	uint32_t out_data;  /* Output will be in_data + 0x01020304 */

  };

  
  /* Get version number */

  #define EC_CMD_GET_VERSION 0x0002

  
  enum ec_current_image {
  	EC_IMAGE_UNKNOWN = 0,
  	EC_IMAGE_RO,
  	EC_IMAGE_RW
  };

  struct __ec_align4 ec_response_get_version {

  	/* Null-terminated version strings for RO, RW */
  	char version_string_ro[32];
  	char version_string_rw[32];
  	char reserved[32];       /* Was previously RW-B string */
  	uint32_t current_image;  /* One of ec_current_image */

  };

  
  /* Read test */

  #define EC_CMD_READ_TEST 0x0003

  struct __ec_align4 ec_params_read_test {

  	uint32_t offset;   /* Starting value for read buffer */
  	uint32_t size;     /* Size to read in bytes */

  };

  struct __ec_align4 ec_response_read_test {

  	uint32_t data[32];

  };

  
  /*
   * Get build information
   *
   * Response is null-terminated string.
   */

  #define EC_CMD_GET_BUILD_INFO 0x0004

  
  /* Get chip info */

  #define EC_CMD_GET_CHIP_INFO 0x0005

  struct __ec_align4 ec_response_get_chip_info {

  	/* Null-terminated strings */
  	char vendor[32];
  	char name[32];
  	char revision[32];  /* Mask version */

  };

  
  /* Get board HW version */

  #define EC_CMD_GET_BOARD_VERSION 0x0006

  struct __ec_align2 ec_response_board_version {

  	uint16_t board_version;  /* A monotonously incrementing number. */

  };

  
  /*
   * Read memory-mapped data.
   *
   * This is an alternate interface to memory-mapped data for bus protocols
   * which don't support direct-mapped memory - I2C, SPI, etc.
   *
   * Response is params.size bytes of data.
   */

  #define EC_CMD_READ_MEMMAP 0x0007

  struct __ec_align1 ec_params_read_memmap {

  	uint8_t offset;   /* Offset in memmap (EC_MEMMAP_*) */
  	uint8_t size;     /* Size to read in bytes */

  };

  
  /* Read versions supported for a command */

  #define EC_CMD_GET_CMD_VERSIONS 0x0008

  struct __ec_align1 ec_params_get_cmd_versions {

  	uint8_t cmd;      /* Command to check */

  };
  
  struct __ec_align2 ec_params_get_cmd_versions_v1 {
  	uint16_t cmd;     /* Command to check */
  };

  struct __ec_align4 ec_response_get_cmd_versions {

  	/*
  	 * Mask of supported versions; use EC_VER_MASK() to compare with a
  	 * desired version.
  	 */
  	uint32_t version_mask;

  };

  
  /*

   * Check EC communications status (busy). This is needed on i2c/spi but not

   * on lpc since it has its own out-of-band busy indicator.
   *
   * lpc must read the status from the command register. Attempting this on
   * lpc will overwrite the args/parameter space and corrupt its data.
   */

  #define EC_CMD_GET_COMMS_STATUS		0x0009

  
  /* Avoid using ec_status which is for return values */
  enum ec_comms_status {
  	EC_COMMS_STATUS_PROCESSING	= 1 << 0,	/* Processing cmd */
  };

  struct __ec_align4 ec_response_get_comms_status {

  	uint32_t flags;		/* Mask of enum ec_comms_status */

  };

  /* Fake a variety of responses, purely for testing purposes. */
  #define EC_CMD_TEST_PROTOCOL		0x000A

  
  /* Tell the EC what to send back to us. */

  struct __ec_align4 ec_params_test_protocol {

  	uint32_t ec_result;
  	uint32_t ret_len;
  	uint8_t buf[32];

  };

  
  /* Here it comes... */

  struct __ec_align4 ec_response_test_protocol {

  	uint8_t buf[32];

  };

  /* Get protocol information */
  #define EC_CMD_GET_PROTOCOL_INFO	0x000B

  
  /* Flags for ec_response_get_protocol_info.flags */
  /* EC_RES_IN_PROGRESS may be returned if a command is slow */
  #define EC_PROTOCOL_INFO_IN_PROGRESS_SUPPORTED (1 << 0)

  struct __ec_align4 ec_response_get_protocol_info {

  	/* Fields which exist if at least protocol version 3 supported */
  
  	/* Bitmask of protocol versions supported (1 << n means version n)*/
  	uint32_t protocol_versions;
  
  	/* Maximum request packet size, in bytes */
  	uint16_t max_request_packet_size;
  
  	/* Maximum response packet size, in bytes */
  	uint16_t max_response_packet_size;
  
  	/* Flags; see EC_PROTOCOL_INFO_* */
  	uint32_t flags;

  };
  
  
  /*****************************************************************************/
  /* Get/Set miscellaneous values */
  
  /* The upper byte of .flags tells what to do (nothing means "get") */
  #define EC_GSV_SET        0x80000000
  
  /* The lower three bytes of .flags identifies the parameter, if that has
     meaning for an individual command. */
  #define EC_GSV_PARAM_MASK 0x00ffffff
  
  struct __ec_align4 ec_params_get_set_value {
  	uint32_t flags;
  	uint32_t value;
  };
  
  struct __ec_align4 ec_response_get_set_value {
  	uint32_t flags;
  	uint32_t value;
  };
  
  /* More than one command can use these structs to get/set parameters. */
  #define EC_CMD_GSV_PAUSE_IN_S5	0x000C
  
  /*****************************************************************************/
  /* List the features supported by the firmware */
  #define EC_CMD_GET_FEATURES  0x000D
  
  /* Supported features */
  enum ec_feature_code {
  	/*
  	 * This image contains a limited set of features. Another image
  	 * in RW partition may support more features.
  	 */
  	EC_FEATURE_LIMITED = 0,
  	/*
  	 * Commands for probing/reading/writing/erasing the flash in the
  	 * EC are present.
  	 */
  	EC_FEATURE_FLASH = 1,
  	/*
  	 * Can control the fan speed directly.
  	 */
  	EC_FEATURE_PWM_FAN = 2,
  	/*
  	 * Can control the intensity of the keyboard backlight.
  	 */
  	EC_FEATURE_PWM_KEYB = 3,
  	/*
  	 * Support Google lightbar, introduced on Pixel.
  	 */
  	EC_FEATURE_LIGHTBAR = 4,
  	/* Control of LEDs  */
  	EC_FEATURE_LED = 5,
  	/* Exposes an interface to control gyro and sensors.
  	 * The host goes through the EC to access these sensors.
  	 * In addition, the EC may provide composite sensors, like lid angle.
  	 */
  	EC_FEATURE_MOTION_SENSE = 6,
  	/* The keyboard is controlled by the EC */
  	EC_FEATURE_KEYB = 7,
  	/* The AP can use part of the EC flash as persistent storage. */
  	EC_FEATURE_PSTORE = 8,
  	/* The EC monitors BIOS port 80h, and can return POST codes. */
  	EC_FEATURE_PORT80 = 9,
  	/*
  	 * Thermal management: include TMP specific commands.
  	 * Higher level than direct fan control.
  	 */
  	EC_FEATURE_THERMAL = 10,
  	/* Can switch the screen backlight on/off */
  	EC_FEATURE_BKLIGHT_SWITCH = 11,
  	/* Can switch the wifi module on/off */
  	EC_FEATURE_WIFI_SWITCH = 12,
  	/* Monitor host events, through for example SMI or SCI */
  	EC_FEATURE_HOST_EVENTS = 13,
  	/* The EC exposes GPIO commands to control/monitor connected devices. */
  	EC_FEATURE_GPIO = 14,
  	/* The EC can send i2c messages to downstream devices. */
  	EC_FEATURE_I2C = 15,
  	/* Command to control charger are included */
  	EC_FEATURE_CHARGER = 16,
  	/* Simple battery support. */
  	EC_FEATURE_BATTERY = 17,
  	/*
  	 * Support Smart battery protocol
  	 * (Common Smart Battery System Interface Specification)
  	 */
  	EC_FEATURE_SMART_BATTERY = 18,
  	/* EC can detect when the host hangs. */
  	EC_FEATURE_HANG_DETECT = 19,
  	/* Report power information, for pit only */
  	EC_FEATURE_PMU = 20,
  	/* Another Cros EC device is present downstream of this one */
  	EC_FEATURE_SUB_MCU = 21,
  	/* Support USB Power delivery (PD) commands */
  	EC_FEATURE_USB_PD = 22,
  	/* Control USB multiplexer, for audio through USB port for instance. */
  	EC_FEATURE_USB_MUX = 23,
  	/* Motion Sensor code has an internal software FIFO */
  	EC_FEATURE_MOTION_SENSE_FIFO = 24,
  	/* Support temporary secure vstore */
  	EC_FEATURE_VSTORE = 25,
  	/* EC decides on USB-C SS mux state, muxes configured by host */
  	EC_FEATURE_USBC_SS_MUX_VIRTUAL = 26,
  	/* EC has RTC feature that can be controlled by host commands */
  	EC_FEATURE_RTC = 27,
  	/* The MCU exposes a Fingerprint sensor */
  	EC_FEATURE_FINGERPRINT = 28,
  	/* The MCU exposes a Touchpad */
  	EC_FEATURE_TOUCHPAD = 29,
  	/* The MCU has RWSIG task enabled */
  	EC_FEATURE_RWSIG = 30,
  	/* EC has device events support */
  	EC_FEATURE_DEVICE_EVENT = 31,
  	/* EC supports the unified wake masks for LPC/eSPI systems */
  	EC_FEATURE_UNIFIED_WAKE_MASKS = 32,
  };
  
  #define EC_FEATURE_MASK_0(event_code) (1UL << (event_code % 32))
  #define EC_FEATURE_MASK_1(event_code) (1UL << (event_code - 32))
  struct __ec_align4 ec_response_get_features {
  	uint32_t flags[2];
  };
  
  /*****************************************************************************/
  /* Get the board's SKU ID from EC */
  #define EC_CMD_GET_SKU_ID 0x000E
  
  /* Set SKU ID from AP */
  #define EC_CMD_SET_SKU_ID 0x000F
  
  struct __ec_align4 ec_sku_id_info {
  	uint32_t sku_id;
  };

  
  /*****************************************************************************/
  /* Flash commands */
  
  /* Get flash info */

  #define EC_CMD_FLASH_INFO 0x0010
  #define EC_VER_FLASH_INFO 2

  /* Version 0 returns these fields */
  struct __ec_align4 ec_response_flash_info {

  	/* Usable flash size, in bytes */
  	uint32_t flash_size;
  	/*
  	 * Write block size.  Write offset and size must be a multiple
  	 * of this.
  	 */
  	uint32_t write_block_size;
  	/*
  	 * Erase block size.  Erase offset and size must be a multiple
  	 * of this.
  	 */
  	uint32_t erase_block_size;
  	/*
  	 * Protection block size.  Protection offset and size must be a
  	 * multiple of this.
  	 */
  	uint32_t protect_block_size;

  };
  
  /* Flags for version 1+ flash info command */
  /* EC flash erases bits to 0 instead of 1 */
  #define EC_FLASH_INFO_ERASE_TO_0 (1 << 0)
  
  /* Flash must be selected for read/write/erase operations to succeed.  This may
   * be necessary on a chip where write/erase can be corrupted by other board
   * activity, or where the chip needs to enable some sort of programming voltage,
   * or where the read/write/erase operations require cleanly suspending other
   * chip functionality. */
  #define EC_FLASH_INFO_SELECT_REQUIRED (1 << 1)

  
  /*

   * Version 1 returns the same initial fields as version 0, with additional
   * fields following.

   *

   * gcc anonymous structs don't seem to get along with the __packed directive;
   * if they did we'd define the version 0 structure as a sub-structure of this
   * one.
   *
   * Version 2 supports flash banks of different sizes:
   * The caller specified the number of banks it has preallocated
   * (num_banks_desc)
   * The EC returns the number of banks describing the flash memory.
   * It adds banks descriptions up to num_banks_desc.

   */

  struct __ec_align4 ec_response_flash_info_1 {
  	/* Version 0 fields; see above for description */
  	uint32_t flash_size;
  	uint32_t write_block_size;
  	uint32_t erase_block_size;
  	uint32_t protect_block_size;

  	/* Version 1 adds these fields: */
  	/*
  	 * Ideal write size in bytes.  Writes will be fastest if size is
  	 * exactly this and offset is a multiple of this.  For example, an EC
  	 * may have a write buffer which can do half-page operations if data is
  	 * aligned, and a slower word-at-a-time write mode.
  	 */
  	uint32_t write_ideal_size;

  	/* Flags; see EC_FLASH_INFO_* */
  	uint32_t flags;
  };

  struct __ec_align4 ec_params_flash_info_2 {
  	/* Number of banks to describe */
  	uint16_t num_banks_desc;
  	/* Reserved; set 0; ignore on read */
  	uint8_t reserved[2];
  };
  
  struct ec_flash_bank {
  	/* Number of sector is in this bank. */
  	uint16_t count;
  	/* Size in power of 2 of each sector (8 --> 256 bytes) */
  	uint8_t size_exp;
  	/* Minimal write size for the sectors in this bank */
  	uint8_t write_size_exp;
  	/* Erase size for the sectors in this bank */
  	uint8_t erase_size_exp;
  	/* Size for write protection, usually identical to erase size. */
  	uint8_t protect_size_exp;
  	/* Reserved; set 0; ignore on read */
  	uint8_t reserved[2];
  };
  
  struct __ec_align4 ec_response_flash_info_2 {
  	/* Total flash in the EC. */
  	uint32_t flash_size;
  	/* Flags; see EC_FLASH_INFO_* */
  	uint32_t flags;
  	/* Maximum size to use to send data to write to the EC. */
  	uint32_t write_ideal_size;
  	/* Number of banks present in the EC. */
  	uint16_t num_banks_total;
  	/* Number of banks described in banks array. */
  	uint16_t num_banks_desc;
  	struct ec_flash_bank banks[0];
  };
  
  /*
   * Read flash
   *
   * Response is params.size bytes of data.
   */
  #define EC_CMD_FLASH_READ 0x0011
  
  struct __ec_align4 ec_params_flash_read {
  	uint32_t offset;   /* Byte offset to read */
  	uint32_t size;     /* Size to read in bytes */
  };
  
  /* Write flash */
  #define EC_CMD_FLASH_WRITE 0x0012
  #define EC_VER_FLASH_WRITE 1
  
  /* Version 0 of the flash command supported only 64 bytes of data */

  #define EC_FLASH_WRITE_VER0_SIZE 64

  struct __ec_align4 ec_params_flash_write {

  	uint32_t offset;   /* Byte offset to write */
  	uint32_t size;     /* Size to write in bytes */

  	/* Followed by data to write */

  };

  
  /* Erase flash */

  #define EC_CMD_FLASH_ERASE 0x0013

  /* v0 */
  struct __ec_align4 ec_params_flash_erase {

  	uint32_t offset;   /* Byte offset to erase */
  	uint32_t size;     /* Size to erase in bytes */

  };
  
  
  #define EC_VER_FLASH_WRITE 1
  /* v1 add async erase:
   * subcommands can returns:
   * EC_RES_SUCCESS : erased (see ERASE_SECTOR_ASYNC case below).
   * EC_RES_INVALID_PARAM : offset/size are not aligned on a erase boundary.
   * EC_RES_ERROR : other errors.
   * EC_RES_BUSY : an existing erase operation is in progress.
   * EC_RES_ACCESS_DENIED: Trying to erase running image.
   *
   * When ERASE_SECTOR_ASYNC returns EC_RES_SUCCESS, the operation is just
   * properly queued. The user must call ERASE_GET_RESULT subcommand to get
   * the proper result.
   * When ERASE_GET_RESULT returns EC_RES_BUSY, the caller must wait and send
   * ERASE_GET_RESULT again to get the result of ERASE_SECTOR_ASYNC.
   * ERASE_GET_RESULT command may timeout on EC where flash access is not
   * permitted while erasing. (For instance, STM32F4).
   */
  enum ec_flash_erase_cmd {
  	FLASH_ERASE_SECTOR,     /* Erase and wait for result */
  	FLASH_ERASE_SECTOR_ASYNC,  /* Erase and return immediately. */
  	FLASH_ERASE_GET_RESULT,  /* Ask for last erase result */
  };
  
  struct __ec_align4 ec_params_flash_erase_v1 {
  	/* One of ec_flash_erase_cmd. */
  	uint8_t  cmd;
  	/* Pad byte; currently always contains 0 */
  	uint8_t  reserved;
  	/* No flags defined yet; set to 0 */
  	uint16_t flag;
  	/* Same as v0 parameters. */
  	struct ec_params_flash_erase params;
  };

  
  /*
   * Get/set flash protection.
   *
   * If mask!=0, sets/clear the requested bits of flags.  Depending on the
   * firmware write protect GPIO, not all flags will take effect immediately;
   * some flags require a subsequent hard reset to take effect.  Check the
   * returned flags bits to see what actually happened.
   *
   * If mask=0, simply returns the current flags state.
   */

  #define EC_CMD_FLASH_PROTECT 0x0015

  #define EC_VER_FLASH_PROTECT 1  /* Command version 1 */
  
  /* Flags for flash protection */
  /* RO flash code protected when the EC boots */
  #define EC_FLASH_PROTECT_RO_AT_BOOT         (1 << 0)
  /*
   * RO flash code protected now.  If this bit is set, at-boot status cannot
   * be changed.
   */
  #define EC_FLASH_PROTECT_RO_NOW             (1 << 1)
  /* Entire flash code protected now, until reboot. */
  #define EC_FLASH_PROTECT_ALL_NOW            (1 << 2)
  /* Flash write protect GPIO is asserted now */
  #define EC_FLASH_PROTECT_GPIO_ASSERTED      (1 << 3)
  /* Error - at least one bank of flash is stuck locked, and cannot be unlocked */
  #define EC_FLASH_PROTECT_ERROR_STUCK        (1 << 4)
  /*
   * Error - flash protection is in inconsistent state.  At least one bank of
   * flash which should be protected is not protected.  Usually fixed by
   * re-requesting the desired flags, or by a hard reset if that fails.
   */
  #define EC_FLASH_PROTECT_ERROR_INCONSISTENT (1 << 5)

  /* Entire flash code protected when the EC boots */

  #define EC_FLASH_PROTECT_ALL_AT_BOOT        (1 << 6)

  /* RW flash code protected when the EC boots */
  #define EC_FLASH_PROTECT_RW_AT_BOOT         (1 << 7)
  /* RW flash code protected now. */
  #define EC_FLASH_PROTECT_RW_NOW             (1 << 8)
  /* Rollback information flash region protected when the EC boots */
  #define EC_FLASH_PROTECT_ROLLBACK_AT_BOOT   (1 << 9)
  /* Rollback information flash region protected now */
  #define EC_FLASH_PROTECT_ROLLBACK_NOW       (1 << 10)
  
  struct __ec_align4 ec_params_flash_protect {

  	uint32_t mask;   /* Bits in flags to apply */
  	uint32_t flags;  /* New flags to apply */

  };

  struct __ec_align4 ec_response_flash_protect {

  	/* Current value of flash protect flags */
  	uint32_t flags;
  	/*
  	 * Flags which are valid on this platform.  This allows the caller
  	 * to distinguish between flags which aren't set vs. flags which can't
  	 * be set on this platform.
  	 */
  	uint32_t valid_flags;
  	/* Flags which can be changed given the current protection state */
  	uint32_t writable_flags;

  };

  
  /*
   * Note: commands 0x14 - 0x19 version 0 were old commands to get/set flash
   * write protect.  These commands may be reused with version > 0.
   */
  
  /* Get the region offset/size */

  #define EC_CMD_FLASH_REGION_INFO 0x0016

  #define EC_VER_FLASH_REGION_INFO 1
  
  enum ec_flash_region {
  	/* Region which holds read-only EC image */

  	EC_FLASH_REGION_RO = 0,

  	/* Region which holds active rewritable EC image */
  	EC_FLASH_REGION_ACTIVE,

  	/*
  	 * Region which should be write-protected in the factory (a superset of
  	 * EC_FLASH_REGION_RO)
  	 */
  	EC_FLASH_REGION_WP_RO,

  	/* Region which holds updatable image */
  	EC_FLASH_REGION_UPDATE,

  	/* Number of regions */
  	EC_FLASH_REGION_COUNT,

  };

  struct __ec_align4 ec_params_flash_region_info {

  	uint32_t region;  /* enum ec_flash_region */

  };

  struct __ec_align4 ec_response_flash_region_info {

  	uint32_t offset;
  	uint32_t size;

  };

  
  /* Read/write VbNvContext */

  #define EC_CMD_VBNV_CONTEXT 0x0017

  #define EC_VER_VBNV_CONTEXT 1
  #define EC_VBNV_BLOCK_SIZE 16

  #define EC_VBNV_BLOCK_SIZE_V2 64

  
  enum ec_vbnvcontext_op {
  	EC_VBNV_CONTEXT_OP_READ,
  	EC_VBNV_CONTEXT_OP_WRITE,
  };

  struct __ec_align4 ec_params_vbnvcontext {

  	uint32_t op;

  	uint8_t block[EC_VBNV_BLOCK_SIZE_V2];
  };
  
  struct __ec_align4 ec_response_vbnvcontext {
  	uint8_t block[EC_VBNV_BLOCK_SIZE_V2];
  };
  
  
  /* Get SPI flash information */
  #define EC_CMD_FLASH_SPI_INFO 0x0018
  
  struct __ec_align1 ec_response_flash_spi_info {
  	/* JEDEC info from command 0x9F (manufacturer, memory type, size) */
  	uint8_t jedec[3];
  
  	/* Pad byte; currently always contains 0 */
  	uint8_t reserved0;
  
  	/* Manufacturer / device ID from command 0x90 */
  	uint8_t mfr_dev_id[2];
  
  	/* Status registers from command 0x05 and 0x35 */
  	uint8_t sr1, sr2;
  };

  /* Select flash during flash operations */
  #define EC_CMD_FLASH_SELECT 0x0019
  
  struct __ec_align4 ec_params_flash_select {
  	/* 1 to select flash, 0 to deselect flash */
  	uint8_t select;
  };

  
  /*****************************************************************************/
  /* PWM commands */
  
  /* Get fan target RPM */

  #define EC_CMD_PWM_GET_FAN_TARGET_RPM 0x0020

  struct __ec_align4 ec_response_pwm_get_fan_rpm {

  	uint32_t rpm;

  };

  
  /* Set target fan RPM */

  #define EC_CMD_PWM_SET_FAN_TARGET_RPM 0x0021
  
  /* Version 0 of input params */
  struct __ec_align4 ec_params_pwm_set_fan_target_rpm_v0 {
  	uint32_t rpm;
  };

  /* Version 1 of input params */
  struct __ec_align_size1 ec_params_pwm_set_fan_target_rpm_v1 {

  	uint32_t rpm;

  	uint8_t fan_idx;
  };

  
  /* Get keyboard backlight */

  /* OBSOLETE - Use EC_CMD_PWM_SET_DUTY */
  #define EC_CMD_PWM_GET_KEYBOARD_BACKLIGHT 0x0022

  struct __ec_align1 ec_response_pwm_get_keyboard_backlight {

  	uint8_t percent;
  	uint8_t enabled;

  };

  
  /* Set keyboard backlight */

  /* OBSOLETE - Use EC_CMD_PWM_SET_DUTY */
  #define EC_CMD_PWM_SET_KEYBOARD_BACKLIGHT 0x0023

  struct __ec_align1 ec_params_pwm_set_keyboard_backlight {

  	uint8_t percent;

  };

  
  /* Set target fan PWM duty cycle */

  #define EC_CMD_PWM_SET_FAN_DUTY 0x0024
  
  /* Version 0 of input params */
  struct __ec_align4 ec_params_pwm_set_fan_duty_v0 {
  	uint32_t percent;
  };

  /* Version 1 of input params */
  struct __ec_align_size1 ec_params_pwm_set_fan_duty_v1 {

  	uint32_t percent;

  	uint8_t fan_idx;
  };
  
  #define EC_CMD_PWM_SET_DUTY 0x0025
  /* 16 bit duty cycle, 0xffff = 100% */
  #define EC_PWM_MAX_DUTY 0xffff
  
  enum ec_pwm_type {
  	/* All types, indexed by board-specific enum pwm_channel */
  	EC_PWM_TYPE_GENERIC = 0,
  	/* Keyboard backlight */
  	EC_PWM_TYPE_KB_LIGHT,
  	/* Display backlight */
  	EC_PWM_TYPE_DISPLAY_LIGHT,
  	EC_PWM_TYPE_COUNT,
  };
  
  struct __ec_align4 ec_params_pwm_set_duty {
  	uint16_t duty;     /* Duty cycle, EC_PWM_MAX_DUTY = 100% */
  	uint8_t pwm_type;  /* ec_pwm_type */
  	uint8_t index;     /* Type-specific index, or 0 if unique */
  };
  
  #define EC_CMD_PWM_GET_DUTY 0x0026
  
  struct __ec_align1 ec_params_pwm_get_duty {
  	uint8_t pwm_type;  /* ec_pwm_type */
  	uint8_t index;     /* Type-specific index, or 0 if unique */
  };
  
  struct __ec_align2 ec_response_pwm_get_duty {
  	uint16_t duty;     /* Duty cycle, EC_PWM_MAX_DUTY = 100% */
  };

  
  /*****************************************************************************/
  /*
   * Lightbar commands. This looks worse than it is. Since we only use one HOST
   * command to say "talk to the lightbar", we put the "and tell it to do X" part
   * into a subcommand. We'll make separate structs for subcommands with
   * different input args, so that we know how much to expect.
   */

  #define EC_CMD_LIGHTBAR_CMD 0x0028

  struct __ec_todo_unpacked rgb_s {

  	uint8_t r, g, b;
  };
  
  #define LB_BATTERY_LEVELS 4
  /* List of tweakable parameters. NOTE: It's __packed so it can be sent in a
   * host command, but the alignment is the same regardless. Keep it that way.
   */

  struct __ec_todo_packed lightbar_params_v0 {

  	/* Timing */

  	int32_t google_ramp_up;
  	int32_t google_ramp_down;
  	int32_t s3s0_ramp_up;
  	int32_t s0_tick_delay[2];		/* AC=0/1 */
  	int32_t s0a_tick_delay[2];		/* AC=0/1 */
  	int32_t s0s3_ramp_down;
  	int32_t s3_sleep_for;
  	int32_t s3_ramp_up;
  	int32_t s3_ramp_down;

  
  	/* Oscillation */
  	uint8_t new_s0;
  	uint8_t osc_min[2];			/* AC=0/1 */
  	uint8_t osc_max[2];			/* AC=0/1 */
  	uint8_t w_ofs[2];			/* AC=0/1 */
  
  	/* Brightness limits based on the backlight and AC. */
  	uint8_t bright_bl_off_fixed[2];		/* AC=0/1 */
  	uint8_t bright_bl_on_min[2];		/* AC=0/1 */
  	uint8_t bright_bl_on_max[2];		/* AC=0/1 */
  
  	/* Battery level thresholds */
  	uint8_t battery_threshold[LB_BATTERY_LEVELS - 1];
  
  	/* Map [AC][battery_level] to color index */
  	uint8_t s0_idx[2][LB_BATTERY_LEVELS];	/* AP is running */
  	uint8_t s3_idx[2][LB_BATTERY_LEVELS];	/* AP is sleeping */
  
  	/* Color palette */
  	struct rgb_s color[8];			/* 0-3 are Google colors */

  };
  
  struct __ec_todo_packed lightbar_params_v1 {
  	/* Timing */
  	int32_t google_ramp_up;
  	int32_t google_ramp_down;
  	int32_t s3s0_ramp_up;
  	int32_t s0_tick_delay[2];		/* AC=0/1 */
  	int32_t s0a_tick_delay[2];		/* AC=0/1 */
  	int32_t s0s3_ramp_down;
  	int32_t s3_sleep_for;
  	int32_t s3_ramp_up;
  	int32_t s3_ramp_down;
  	int32_t s5_ramp_up;
  	int32_t s5_ramp_down;
  	int32_t tap_tick_delay;
  	int32_t tap_gate_delay;
  	int32_t tap_display_time;
  
  	/* Tap-for-battery params */
  	uint8_t tap_pct_red;
  	uint8_t tap_pct_green;
  	uint8_t tap_seg_min_on;
  	uint8_t tap_seg_max_on;
  	uint8_t tap_seg_osc;
  	uint8_t tap_idx[3];
  
  	/* Oscillation */
  	uint8_t osc_min[2];			/* AC=0/1 */
  	uint8_t osc_max[2];			/* AC=0/1 */
  	uint8_t w_ofs[2];			/* AC=0/1 */
  
  	/* Brightness limits based on the backlight and AC. */
  	uint8_t bright_bl_off_fixed[2];		/* AC=0/1 */
  	uint8_t bright_bl_on_min[2];		/* AC=0/1 */
  	uint8_t bright_bl_on_max[2];		/* AC=0/1 */
  
  	/* Battery level thresholds */
  	uint8_t battery_threshold[LB_BATTERY_LEVELS - 1];
  
  	/* Map [AC][battery_level] to color index */
  	uint8_t s0_idx[2][LB_BATTERY_LEVELS];	/* AP is running */
  	uint8_t s3_idx[2][LB_BATTERY_LEVELS];	/* AP is sleeping */
  
  	/* s5: single color pulse on inhibited power-up */
  	uint8_t s5_idx;
  
  	/* Color palette */
  	struct rgb_s color[8];			/* 0-3 are Google colors */
  };
  
  /* Lightbar command params v2
   * crbug.com/467716
   *
   * lightbar_parms_v1 was too big for i2c, therefore in v2, we split them up by
   * logical groups to make it more manageable ( < 120 bytes).
   *
   * NOTE: Each of these groups must be less than 120 bytes.
   */
  
  struct __ec_todo_packed lightbar_params_v2_timing {
  	/* Timing */
  	int32_t google_ramp_up;
  	int32_t google_ramp_down;
  	int32_t s3s0_ramp_up;
  	int32_t s0_tick_delay[2];		/* AC=0/1 */
  	int32_t s0a_tick_delay[2];		/* AC=0/1 */
  	int32_t s0s3_ramp_down;
  	int32_t s3_sleep_for;
  	int32_t s3_ramp_up;
  	int32_t s3_ramp_down;
  	int32_t s5_ramp_up;
  	int32_t s5_ramp_down;
  	int32_t tap_tick_delay;
  	int32_t tap_gate_delay;
  	int32_t tap_display_time;
  };
  
  struct __ec_todo_packed lightbar_params_v2_tap {
  	/* Tap-for-battery params */
  	uint8_t tap_pct_red;
  	uint8_t tap_pct_green;
  	uint8_t tap_seg_min_on;
  	uint8_t tap_seg_max_on;
  	uint8_t tap_seg_osc;
  	uint8_t tap_idx[3];
  };
  
  struct __ec_todo_packed lightbar_params_v2_oscillation {
  	/* Oscillation */
  	uint8_t osc_min[2];			/* AC=0/1 */
  	uint8_t osc_max[2];			/* AC=0/1 */
  	uint8_t w_ofs[2];			/* AC=0/1 */
  };
  
  struct __ec_todo_packed lightbar_params_v2_brightness {
  	/* Brightness limits based on the backlight and AC. */
  	uint8_t bright_bl_off_fixed[2];		/* AC=0/1 */
  	uint8_t bright_bl_on_min[2];		/* AC=0/1 */
  	uint8_t bright_bl_on_max[2];		/* AC=0/1 */
  };
  
  struct __ec_todo_packed lightbar_params_v2_thresholds {
  	/* Battery level thresholds */
  	uint8_t battery_threshold[LB_BATTERY_LEVELS - 1];
  };
  
  struct __ec_todo_packed lightbar_params_v2_colors {
  	/* Map [AC][battery_level] to color index */
  	uint8_t s0_idx[2][LB_BATTERY_LEVELS];	/* AP is running */
  	uint8_t s3_idx[2][LB_BATTERY_LEVELS];	/* AP is sleeping */
  
  	/* s5: single color pulse on inhibited power-up */
  	uint8_t s5_idx;
  
  	/* Color palette */
  	struct rgb_s color[8];			/* 0-3 are Google colors */
  };
  
  /* Lightbyte program. */
  #define EC_LB_PROG_LEN 192
  struct __ec_todo_unpacked lightbar_program {
  	uint8_t size;
  	uint8_t data[EC_LB_PROG_LEN];
  };

  struct __ec_todo_packed ec_params_lightbar {

  	uint8_t cmd;		      /* Command (see enum lightbar_command) */
  	union {

  		struct __ec_todo_unpacked {

  			/* no args */

  		} dump, off, on, init, get_seq, get_params_v0, get_params_v1,
  			version, get_brightness, get_demo, suspend, resume,
  			get_params_v2_timing, get_params_v2_tap,
  			get_params_v2_osc, get_params_v2_bright,
  			get_params_v2_thlds, get_params_v2_colors;

  		struct __ec_todo_unpacked {

  			uint8_t num;

  		} set_brightness, seq, demo;

  		struct __ec_todo_unpacked {

  			uint8_t ctrl, reg, value;
  		} reg;

  		struct __ec_todo_unpacked {

  			uint8_t led, red, green, blue;

  		} set_rgb;
  
  		struct __ec_todo_unpacked {
  			uint8_t led;
  		} get_rgb;

  		struct __ec_todo_unpacked {
  			uint8_t enable;
  		} manual_suspend_ctrl;
  
  		struct lightbar_params_v0 set_params_v0;
  		struct lightbar_params_v1 set_params_v1;
  
  		struct lightbar_params_v2_timing set_v2par_timing;
  		struct lightbar_params_v2_tap set_v2par_tap;
  		struct lightbar_params_v2_oscillation set_v2par_osc;
  		struct lightbar_params_v2_brightness set_v2par_bright;
  		struct lightbar_params_v2_thresholds set_v2par_thlds;
  		struct lightbar_params_v2_colors set_v2par_colors;
  
  		struct lightbar_program set_program;

  	};

  };

  struct __ec_todo_packed ec_response_lightbar {

  	union {

  		struct __ec_todo_unpacked {
  			struct __ec_todo_unpacked {

  				uint8_t reg;
  				uint8_t ic0;
  				uint8_t ic1;
  			} vals[23];
  		} dump;

  		struct __ec_todo_unpacked {

  			uint8_t num;

  		} get_seq, get_brightness, get_demo;

  		struct lightbar_params_v0 get_params_v0;
  		struct lightbar_params_v1 get_params_v1;

  
  		struct lightbar_params_v2_timing get_params_v2_timing;
  		struct lightbar_params_v2_tap get_params_v2_tap;
  		struct lightbar_params_v2_oscillation get_params_v2_osc;
  		struct lightbar_params_v2_brightness get_params_v2_bright;
  		struct lightbar_params_v2_thresholds get_params_v2_thlds;
  		struct lightbar_params_v2_colors get_params_v2_colors;
  
  		struct __ec_todo_unpacked {
  			uint32_t num;
  			uint32_t flags;
  		} version;
  
  		struct __ec_todo_unpacked {
  			uint8_t red, green, blue;
  		} get_rgb;
  
  		struct __ec_todo_unpacked {

  			/* no return params */

  		} off, on, init, set_brightness, seq, reg, set_rgb,
  			demo, set_params_v0, set_params_v1,
  			set_program, manual_suspend_ctrl, suspend, resume,
  			set_v2par_timing, set_v2par_tap,
  			set_v2par_osc, set_v2par_bright, set_v2par_thlds,
  			set_v2par_colors;

  	};

  };

  
  /* Lightbar commands */
  enum lightbar_command {
  	LIGHTBAR_CMD_DUMP = 0,
  	LIGHTBAR_CMD_OFF = 1,
  	LIGHTBAR_CMD_ON = 2,
  	LIGHTBAR_CMD_INIT = 3,

  	LIGHTBAR_CMD_SET_BRIGHTNESS = 4,

  	LIGHTBAR_CMD_SEQ = 5,
  	LIGHTBAR_CMD_REG = 6,

  	LIGHTBAR_CMD_SET_RGB = 7,

  	LIGHTBAR_CMD_GET_SEQ = 8,
  	LIGHTBAR_CMD_DEMO = 9,

  	LIGHTBAR_CMD_GET_PARAMS_V0 = 10,
  	LIGHTBAR_CMD_SET_PARAMS_V0 = 11,
  	LIGHTBAR_CMD_VERSION = 12,
  	LIGHTBAR_CMD_GET_BRIGHTNESS = 13,
  	LIGHTBAR_CMD_GET_RGB = 14,
  	LIGHTBAR_CMD_GET_DEMO = 15,
  	LIGHTBAR_CMD_GET_PARAMS_V1 = 16,
  	LIGHTBAR_CMD_SET_PARAMS_V1 = 17,
  	LIGHTBAR_CMD_SET_PROGRAM = 18,
  	LIGHTBAR_CMD_MANUAL_SUSPEND_CTRL = 19,
  	LIGHTBAR_CMD_SUSPEND = 20,
  	LIGHTBAR_CMD_RESUME = 21,
  	LIGHTBAR_CMD_GET_PARAMS_V2_TIMING = 22,
  	LIGHTBAR_CMD_SET_PARAMS_V2_TIMING = 23,
  	LIGHTBAR_CMD_GET_PARAMS_V2_TAP = 24,
  	LIGHTBAR_CMD_SET_PARAMS_V2_TAP = 25,
  	LIGHTBAR_CMD_GET_PARAMS_V2_OSCILLATION = 26,
  	LIGHTBAR_CMD_SET_PARAMS_V2_OSCILLATION = 27,
  	LIGHTBAR_CMD_GET_PARAMS_V2_BRIGHTNESS = 28,
  	LIGHTBAR_CMD_SET_PARAMS_V2_BRIGHTNESS = 29,
  	LIGHTBAR_CMD_GET_PARAMS_V2_THRESHOLDS = 30,
  	LIGHTBAR_CMD_SET_PARAMS_V2_THRESHOLDS = 31,
  	LIGHTBAR_CMD_GET_PARAMS_V2_COLORS = 32,
  	LIGHTBAR_CMD_SET_PARAMS_V2_COLORS = 33,

  	LIGHTBAR_NUM_CMDS
  };
  
  /*****************************************************************************/

  /* LED control commands */

  #define EC_CMD_LED_CONTROL 0x0029

  
  enum ec_led_id {

  	/* LED to indicate battery state of charge */

  	EC_LED_ID_BATTERY_LED = 0,

  	/*
  	 * LED to indicate system power state (on or in suspend).
  	 * May be on power button or on C-panel.
  	 */
  	EC_LED_ID_POWER_LED,
  	/* LED on power adapter or its plug */

  	EC_LED_ID_ADAPTER_LED,

  	/* LED to indicate left side */
  	EC_LED_ID_LEFT_LED,
  	/* LED to indicate right side */
  	EC_LED_ID_RIGHT_LED,
  	/* LED to indicate recovery mode with HW_REINIT */
  	EC_LED_ID_RECOVERY_HW_REINIT_LED,
  	/* LED to indicate sysrq debug mode. */
  	EC_LED_ID_SYSRQ_DEBUG_LED,
  
  	EC_LED_ID_COUNT

  };
  
  /* LED control flags */
  #define EC_LED_FLAGS_QUERY (1 << 0) /* Query LED capability only */
  #define EC_LED_FLAGS_AUTO  (1 << 1) /* Switch LED back to automatic control */
  
  enum ec_led_colors {
  	EC_LED_COLOR_RED = 0,
  	EC_LED_COLOR_GREEN,
  	EC_LED_COLOR_BLUE,
  	EC_LED_COLOR_YELLOW,
  	EC_LED_COLOR_WHITE,

  	EC_LED_COLOR_AMBER,

  
  	EC_LED_COLOR_COUNT
  };

  struct __ec_align1 ec_params_led_control {

  	uint8_t led_id;     /* Which LED to control */
  	uint8_t flags;      /* Control flags */
  
  	uint8_t brightness[EC_LED_COLOR_COUNT];

  };

  struct __ec_align1 ec_response_led_control {

  	/*
  	 * Available brightness value range.
  	 *
  	 * Range 0 means color channel not present.
  	 * Range 1 means on/off control.
  	 * Other values means the LED is control by PWM.
  	 */
  	uint8_t brightness_range[EC_LED_COLOR_COUNT];

  };

  
  /*****************************************************************************/

  /* Verified boot commands */
  
  /*
   * Note: command code 0x29 version 0 was VBOOT_CMD in Link EVT; it may be
   * reused for other purposes with version > 0.
   */
  
  /* Verified boot hash command */

  #define EC_CMD_VBOOT_HASH 0x002A

  struct __ec_align4 ec_params_vboot_hash {

  	uint8_t cmd;             /* enum ec_vboot_hash_cmd */
  	uint8_t hash_type;       /* enum ec_vboot_hash_type */
  	uint8_t nonce_size;      /* Nonce size; may be 0 */
  	uint8_t reserved0;       /* Reserved; set 0 */
  	uint32_t offset;         /* Offset in flash to hash */
  	uint32_t size;           /* Number of bytes to hash */
  	uint8_t nonce_data[64];  /* Nonce data; ignored if nonce_size=0 */

  };

  struct __ec_align4 ec_response_vboot_hash {

  	uint8_t status;          /* enum ec_vboot_hash_status */
  	uint8_t hash_type;       /* enum ec_vboot_hash_type */
  	uint8_t digest_size;     /* Size of hash digest in bytes */
  	uint8_t reserved0;       /* Ignore; will be 0 */
  	uint32_t offset;         /* Offset in flash which was hashed */
  	uint32_t size;           /* Number of bytes hashed */
  	uint8_t hash_digest[64]; /* Hash digest data */

  };

  
  enum ec_vboot_hash_cmd {
  	EC_VBOOT_HASH_GET = 0,       /* Get current hash status */
  	EC_VBOOT_HASH_ABORT = 1,     /* Abort calculating current hash */
  	EC_VBOOT_HASH_START = 2,     /* Start computing a new hash */
  	EC_VBOOT_HASH_RECALC = 3,    /* Synchronously compute a new hash */
  };
  
  enum ec_vboot_hash_type {
  	EC_VBOOT_HASH_TYPE_SHA256 = 0, /* SHA-256 */
  };
  
  enum ec_vboot_hash_status {
  	EC_VBOOT_HASH_STATUS_NONE = 0, /* No hash (not started, or aborted) */
  	EC_VBOOT_HASH_STATUS_DONE = 1, /* Finished computing a hash */
  	EC_VBOOT_HASH_STATUS_BUSY = 2, /* Busy computing a hash */
  };
  
  /*
   * Special values for offset for EC_VBOOT_HASH_START and EC_VBOOT_HASH_RECALC.
   * If one of these is specified, the EC will automatically update offset and
   * size to the correct values for the specified image (RO or RW).
   */

  #define EC_VBOOT_HASH_OFFSET_RO		0xfffffffe
  #define EC_VBOOT_HASH_OFFSET_ACTIVE	0xfffffffd
  #define EC_VBOOT_HASH_OFFSET_UPDATE	0xfffffffc

  
  /*****************************************************************************/

  /*
   * Motion sense commands. We'll make separate structs for sub-commands with
   * different input args, so that we know how much to expect.
   */
  #define EC_CMD_MOTION_SENSE_CMD 0x002B

  /* Motion sense commands */
  enum motionsense_command {
  	/*
  	 * Dump command returns all motion sensor data including motion sense
  	 * module flags and individual sensor flags.
  	 */
  	MOTIONSENSE_CMD_DUMP = 0,

  	/*
  	 * Info command returns data describing the details of a given sensor,
  	 * including enum motionsensor_type, enum motionsensor_location, and
  	 * enum motionsensor_chip.
  	 */
  	MOTIONSENSE_CMD_INFO = 1,

  	/*
  	 * EC Rate command is a setter/getter command for the EC sampling rate
  	 * in milliseconds.
  	 * It is per sensor, the EC run sample task  at the minimum of all
  	 * sensors EC_RATE.
  	 * For sensors without hardware FIFO, EC_RATE should be equals to 1/ODR
  	 * to collect all the sensor samples.
  	 * For sensor with hardware FIFO, EC_RATE is used as the maximal delay
  	 * to process of all motion sensors in milliseconds.
  	 */
  	MOTIONSENSE_CMD_EC_RATE = 2,

  	/*
  	 * Sensor ODR command is a setter/getter command for the output data
  	 * rate of a specific motion sensor in millihertz.
  	 */
  	MOTIONSENSE_CMD_SENSOR_ODR = 3,

  	/*
  	 * Sensor range command is a setter/getter command for the range of
  	 * a specified motion sensor in +/-G's or +/- deg/s.
  	 */
  	MOTIONSENSE_CMD_SENSOR_RANGE = 4,

  	/*
  	 * Setter/getter command for the keyboard wake angle. When the lid
  	 * angle is greater than this value, keyboard wake is disabled in S3,
  	 * and when the lid angle goes less than this value, keyboard wake is
  	 * enabled. Note, the lid angle measurement is an approximate,
  	 * un-calibrated value, hence the wake angle isn't exact.
  	 */
  	MOTIONSENSE_CMD_KB_WAKE_ANGLE = 5,

  	/*
  	 * Returns a single sensor data.
  	 */
  	MOTIONSENSE_CMD_DATA = 6,

  	/*
  	 * Return sensor fifo info.
  	 */
  	MOTIONSENSE_CMD_FIFO_INFO = 7,

  	/*
  	 * Insert a flush element in the fifo and return sensor fifo info.
  	 * The host can use that element to synchronize its operation.
  	 */
  	MOTIONSENSE_CMD_FIFO_FLUSH = 8,

  	/*
  	 * Return a portion of the fifo.
  	 */
  	MOTIONSENSE_CMD_FIFO_READ = 9,

  	/*
  	 * Perform low level calibration.
  	 * On sensors that support it, ask to do offset calibration.
  	 */
  	MOTIONSENSE_CMD_PERFORM_CALIB = 10,

  	/*
  	 * Sensor Offset command is a setter/getter command for the offset
  	 * used for calibration.
  	 * The offsets can be calculated by the host, or via
  	 * PERFORM_CALIB command.
  	 */
  	MOTIONSENSE_CMD_SENSOR_OFFSET = 11,

  	/*
  	 * List available activities for a MOTION sensor.
  	 * Indicates if they are enabled or disabled.
  	 */
  	MOTIONSENSE_CMD_LIST_ACTIVITIES = 12,

  	/*
  	 * Activity management
  	 * Enable/Disable activity recognition.
  	 */
  	MOTIONSENSE_CMD_SET_ACTIVITY = 13,

  	/*
  	 * Lid Angle
  	 */
  	MOTIONSENSE_CMD_LID_ANGLE = 14,

  	/*
  	 * Allow the FIFO to trigger interrupt via MKBP events.
  	 * By default the FIFO does not send interrupt to process the FIFO
  	 * until the AP is ready or it is coming from a wakeup sensor.
  	 */
  	MOTIONSENSE_CMD_FIFO_INT_ENABLE = 15,

  	/*
  	 * Spoof the readings of the sensors.  The spoofed readings can be set
  	 * to arbitrary values, or will lock to the last read actual values.
  	 */
  	MOTIONSENSE_CMD_SPOOF = 16,

  	/* Number of motionsense sub-commands. */
  	MOTIONSENSE_NUM_CMDS
  };

  /* List of motion sensor types. */
  enum motionsensor_type {
  	MOTIONSENSE_TYPE_ACCEL = 0,
  	MOTIONSENSE_TYPE_GYRO = 1,
  	MOTIONSENSE_TYPE_MAG = 2,
  	MOTIONSENSE_TYPE_PROX = 3,
  	MOTIONSENSE_TYPE_LIGHT = 4,
  	MOTIONSENSE_TYPE_ACTIVITY = 5,
  	MOTIONSENSE_TYPE_BARO = 6,
  	MOTIONSENSE_TYPE_MAX,
  };

  /* List of motion sensor locations. */
  enum motionsensor_location {
  	MOTIONSENSE_LOC_BASE = 0,
  	MOTIONSENSE_LOC_LID = 1,
  	MOTIONSENSE_LOC_MAX,
  };

  /* List of motion sensor chips. */
  enum motionsensor_chip {
  	MOTIONSENSE_CHIP_KXCJ9 = 0,
  	MOTIONSENSE_CHIP_LSM6DS0 = 1,
  	MOTIONSENSE_CHIP_BMI160 = 2,
  	MOTIONSENSE_CHIP_SI1141 = 3,
  	MOTIONSENSE_CHIP_SI1142 = 4,
  	MOTIONSENSE_CHIP_SI1143 = 5,
  	MOTIONSENSE_CHIP_KX022 = 6,
  	MOTIONSENSE_CHIP_L3GD20H = 7,
  	MOTIONSENSE_CHIP_BMA255 = 8,
  	MOTIONSENSE_CHIP_BMP280 = 9,
  	MOTIONSENSE_CHIP_OPT3001 = 10,
  };

  struct __ec_todo_packed ec_response_motion_sensor_data {
  	/* Flags for each sensor. */
  	uint8_t flags;
  	/* sensor number the data comes from */
  	uint8_t sensor_num;
  	/* Each sensor is up to 3-axis. */
  	union {
  		int16_t             data[3];
  		struct __ec_todo_packed {
  			uint16_t    reserved;
  			uint32_t    timestamp;
  		};
  		struct __ec_todo_unpacked {
  			uint8_t     activity; /* motionsensor_activity */
  			uint8_t     state;
  			int16_t     add_info[2];
  		};
  	};
  };

  /* Note: used in ec_response_get_next_data */
  struct __ec_todo_packed ec_response_motion_sense_fifo_info {
  	/* Size of the fifo */
  	uint16_t size;
  	/* Amount of space used in the fifo */
  	uint16_t count;
  	/* Timestamp recorded in us */
  	uint32_t timestamp;
  	/* Total amount of vector lost */
  	uint16_t total_lost;
  	/* Lost events since the last fifo_info, per sensors */
  	uint16_t lost[0];
  };

  struct __ec_todo_packed ec_response_motion_sense_fifo_data {
  	uint32_t number_data;
  	struct ec_response_motion_sensor_data data[0];
  };

  /* List supported activity recognition */
  enum motionsensor_activity {
  	MOTIONSENSE_ACTIVITY_RESERVED = 0,
  	MOTIONSENSE_ACTIVITY_SIG_MOTION = 1,
  	MOTIONSENSE_ACTIVITY_DOUBLE_TAP = 2,
  };

  struct __ec_todo_unpacked ec_motion_sense_activity {
  	uint8_t sensor_num;
  	uint8_t activity; /* one of enum motionsensor_activity */
  	uint8_t enable;   /* 1: enable, 0: disable */
  	uint8_t reserved;
  	uint16_t parameters[3]; /* activity dependent parameters */
  };

  /* Module flag masks used for the dump sub-command. */
  #define MOTIONSENSE_MODULE_FLAG_ACTIVE (1<<0)

  /* Sensor flag masks used for the dump sub-command. */
  #define MOTIONSENSE_SENSOR_FLAG_PRESENT (1<<0)

  /*
   * Flush entry for synchronization.
   * data contains time stamp
   */
  #define MOTIONSENSE_SENSOR_FLAG_FLUSH (1<<0)
  #define MOTIONSENSE_SENSOR_FLAG_TIMESTAMP (1<<1)
  #define MOTIONSENSE_SENSOR_FLAG_WAKEUP (1<<2)
  #define MOTIONSENSE_SENSOR_FLAG_TABLET_MODE (1<<3)

  /*
   * Send this value for the data element to only perform a read. If you
   * send any other value, the EC will interpret it as data to set and will
   * return the actual value set.
   */
  #define EC_MOTION_SENSE_NO_VALUE -1

  #define EC_MOTION_SENSE_INVALID_CALIB_TEMP 0x8000
  
  /* MOTIONSENSE_CMD_SENSOR_OFFSET subcommand flag */
  /* Set Calibration information */
  #define MOTION_SENSE_SET_OFFSET 1
  
  #define LID_ANGLE_UNRELIABLE 500
  
  enum motionsense_spoof_mode {
  	/* Disable spoof mode. */
  	MOTIONSENSE_SPOOF_MODE_DISABLE = 0,
  
  	/* Enable spoof mode, but use provided component values. */
  	MOTIONSENSE_SPOOF_MODE_CUSTOM,
  
  	/* Enable spoof mode, but use the current sensor values. */
  	MOTIONSENSE_SPOOF_MODE_LOCK_CURRENT,
  
  	/* Query the current spoof mode status for the sensor. */
  	MOTIONSENSE_SPOOF_MODE_QUERY,
  };
  
  struct __ec_todo_packed ec_params_motion_sense {
  	uint8_t cmd;
  	union {
  		/* Used for MOTIONSENSE_CMD_DUMP */
  		struct __ec_todo_unpacked {
  			/*
  			 * Maximal number of sensor the host is expecting.
  			 * 0 means the host is only interested in the number
  			 * of sensors controlled by the EC.
  			 */
  			uint8_t max_sensor_count;
  		} dump;
  
  		/*
  		 * Used for MOTIONSENSE_CMD_KB_WAKE_ANGLE.
  		 */
  		struct __ec_todo_unpacked {
  			/* Data to set or EC_MOTION_SENSE_NO_VALUE to read.
  			 * kb_wake_angle: angle to wakup AP.
  			 */
  			int16_t data;
  		} kb_wake_angle;
  
  		/* Used for MOTIONSENSE_CMD_INFO, MOTIONSENSE_CMD_DATA
  		 * and MOTIONSENSE_CMD_PERFORM_CALIB. */
  		struct __ec_todo_unpacked {
  			uint8_t sensor_num;
  		} info, info_3, data, fifo_flush, perform_calib,
  				list_activities;
  
  		/*
  		 * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR
  		 * and MOTIONSENSE_CMD_SENSOR_RANGE.
  		 */
  		struct __ec_todo_unpacked {
  			uint8_t sensor_num;
  
  			/* Rounding flag, true for round-up, false for down. */
  			uint8_t roundup;
  
  			uint16_t reserved;
  
  			/* Data to set or EC_MOTION_SENSE_NO_VALUE to read. */
  			int32_t data;
  		} ec_rate, sensor_odr, sensor_range;
  
  		/* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */
  		struct __ec_todo_packed {
  			uint8_t sensor_num;
  
  			/*
  			 * bit 0: If set (MOTION_SENSE_SET_OFFSET), set
  			 * the calibration information in the EC.
  			 * If unset, just retrieve calibration information.
  			 */
  			uint16_t flags;
  
  			/*
  			 * Temperature at calibration, in units of 0.01 C
  			 * 0x8000: invalid / unknown.
  			 * 0x0: 0C
  			 * 0x7fff: +327.67C
  			 */
  			int16_t temp;
  
  			/*
  			 * Offset for calibration.
  			 * Unit:
  			 * Accelerometer: 1/1024 g
  			 * Gyro:          1/1024 deg/s
  			 * Compass:       1/16 uT
  			 */
  			int16_t offset[3];
  		} sensor_offset;
  
  		/* Used for MOTIONSENSE_CMD_FIFO_INFO */
  		struct __ec_todo_unpacked {
  		} fifo_info;
  
  		/* Used for MOTIONSENSE_CMD_FIFO_READ */
  		struct __ec_todo_unpacked {
  			/*
  			 * Number of expected vector to return.
  			 * EC may return less or 0 if none available.
  			 */
  			uint32_t max_data_vector;
  		} fifo_read;
  
  		struct ec_motion_sense_activity set_activity;
  
  		/* Used for MOTIONSENSE_CMD_LID_ANGLE */
  		struct __ec_todo_unpacked {
  		} lid_angle;
  
  		/* Used for MOTIONSENSE_CMD_FIFO_INT_ENABLE */
  		struct __ec_todo_unpacked {
  			/*
  			 * 1: enable, 0 disable fifo,
  			 * EC_MOTION_SENSE_NO_VALUE return value.
  			 */
  			int8_t enable;
  		} fifo_int_enable;
  
  		/* Used for MOTIONSENSE_CMD_SPOOF */
  		struct __ec_todo_packed {
  			uint8_t sensor_id;
  
  			/* See enum motionsense_spoof_mode. */
  			uint8_t spoof_enable;
  
  			/* Ignored, used for alignment. */
  			uint8_t reserved;
  
  			/* Individual component values to spoof. */
  			int16_t components[3];
  		} spoof;
  	};
  };
  
  struct __ec_todo_packed ec_response_motion_sense {
  	union {
  		/* Used for MOTIONSENSE_CMD_DUMP */
  		struct __ec_todo_unpacked {
  			/* Flags representing the motion sensor module. */
  			uint8_t module_flags;
  
  			/* Number of sensors managed directly by the EC */
  			uint8_t sensor_count;
  
  			/*
  			 * sensor data is truncated if response_max is too small
  			 * for holding all the data.
  			 */
  			struct ec_response_motion_sensor_data sensor[0];
  		} dump;
  
  		/* Used for MOTIONSENSE_CMD_INFO. */
  		struct __ec_todo_unpacked {
  			/* Should be element of enum motionsensor_type. */
  			uint8_t type;
  
  			/* Should be element of enum motionsensor_location. */
  			uint8_t location;
  
  			/* Should be element of enum motionsensor_chip. */
  			uint8_t chip;
  		} info;
  
  		/* Used for MOTIONSENSE_CMD_INFO version 3 */
  		struct __ec_todo_unpacked {
  			/* Should be element of enum motionsensor_type. */
  			uint8_t type;
  
  			/* Should be element of enum motionsensor_location. */
  			uint8_t location;
  
  			/* Should be element of enum motionsensor_chip. */
  			uint8_t chip;
  
  			/* Minimum sensor sampling frequency */
  			uint32_t min_frequency;
  
  			/* Maximum sensor sampling frequency */
  			uint32_t max_frequency;
  
  			/* Max number of sensor events that could be in fifo */
  			uint32_t fifo_max_event_count;
  		} info_3;
  
  		/* Used for MOTIONSENSE_CMD_DATA */
  		struct ec_response_motion_sensor_data data;
  
  		/*
  		 * Used for MOTIONSENSE_CMD_EC_RATE, MOTIONSENSE_CMD_SENSOR_ODR,
  		 * MOTIONSENSE_CMD_SENSOR_RANGE,
  		 * MOTIONSENSE_CMD_KB_WAKE_ANGLE,
  		 * MOTIONSENSE_CMD_FIFO_INT_ENABLE and
  		 * MOTIONSENSE_CMD_SPOOF.
  		 */
  		struct __ec_todo_unpacked {
  			/* Current value of the parameter queried. */
  			int32_t ret;
  		} ec_rate, sensor_odr, sensor_range, kb_wake_angle,
  		  fifo_int_enable, spoof;
  
  		/* Used for MOTIONSENSE_CMD_SENSOR_OFFSET */
  		struct __ec_todo_unpacked  {
  			int16_t temp;
  			int16_t offset[3];
  		} sensor_offset, perform_calib;
  
  		struct ec_response_motion_sense_fifo_info fifo_info, fifo_flush;
  
  		struct ec_response_motion_sense_fifo_data fifo_read;
  
  		struct __ec_todo_packed {
  			uint16_t reserved;
  			uint32_t enabled;
  			uint32_t disabled;
  		} list_activities;
  
  		struct __ec_todo_unpacked {
  		} set_activity;
  
  		/* Used for MOTIONSENSE_CMD_LID_ANGLE */
  		struct __ec_todo_unpacked {
  			/*
  			 * Angle between 0 and 360 degree if available,
  			 * LID_ANGLE_UNRELIABLE otherwise.
  			 */
  			uint16_t value;
  		} lid_angle;
  	};
  };
  
  /*****************************************************************************/
  /* Force lid open command */
  
  /* Make lid event always open */
  #define EC_CMD_FORCE_LID_OPEN 0x002C
  
  struct __ec_align1 ec_params_force_lid_open {
  	uint8_t enabled;
  };
  
  /*****************************************************************************/
  /* Configure the behavior of the power button */
  #define EC_CMD_CONFIG_POWER_BUTTON 0x002D
  
  enum ec_config_power_button_flags {
  	/* Enable/Disable power button pulses for x86 devices */
  	EC_POWER_BUTTON_ENABLE_PULSE = (1 << 0),
  };
  
  struct __ec_align1 ec_params_config_power_button {
  	/* See enum ec_config_power_button_flags */
  	uint8_t flags;
  };
  
  /*****************************************************************************/
  /* USB charging control commands */
  
  /* Set USB port charging mode */
  #define EC_CMD_USB_CHARGE_SET_MODE 0x0030
  
  struct __ec_align1 ec_params_usb_charge_set_mode {
  	uint8_t usb_port_id;
  	uint8_t mode;
  };
  
  /*****************************************************************************/
  /* Persistent storage for host */
  
  /* Maximum bytes that can be read/written in a single command */
  #define EC_PSTORE_SIZE_MAX 64
  
  /* Get persistent storage info */
  #define EC_CMD_PSTORE_INFO 0x0040
  
  struct __ec_align4 ec_response_pstore_info {
  	/* Persistent storage size, in bytes */
  	uint32_t pstore_size;
  	/* Access size; read/write offset and size must be a multiple of this */
  	uint32_t access_size;
  };
  
  /*
   * Read persistent storage
   *
   * Response is params.size bytes of data.
   */
  #define EC_CMD_PSTORE_READ 0x0041
  
  struct __ec_align4 ec_params_pstore_read {
  	uint32_t offset;   /* Byte offset to read */
  	uint32_t size;     /* Size to read in bytes */
  };
  
  /* Write persistent storage */
  #define EC_CMD_PSTORE_WRITE 0x0042
  
  struct __ec_align4 ec_params_pstore_write {
  	uint32_t offset;   /* Byte offset to write */
  	uint32_t size;     /* Size to write in bytes */
  	uint8_t data[EC_PSTORE_SIZE_MAX];
  };
  
  /*****************************************************************************/
  /* Real-time clock */
  
  /* RTC params and response structures */
  struct __ec_align4 ec_params_rtc {
  	uint32_t time;
  };
  
  struct __ec_align4 ec_response_rtc {
  	uint32_t time;
  };
  
  /* These use ec_response_rtc */
  #define EC_CMD_RTC_GET_VALUE 0x0044
  #define EC_CMD_RTC_GET_ALARM 0x0045
  
  /* These all use ec_params_rtc */
  #define EC_CMD_RTC_SET_VALUE 0x0046
  #define EC_CMD_RTC_SET_ALARM 0x0047
  
  /* Pass as time param to SET_ALARM to clear the current alarm */
  #define EC_RTC_ALARM_CLEAR 0
  
  /*****************************************************************************/
  /* Port80 log access */
  
  /* Maximum entries that can be read/written in a single command */
  #define EC_PORT80_SIZE_MAX 32
  
  /* Get last port80 code from previous boot */
  #define EC_CMD_PORT80_LAST_BOOT 0x0048
  #define EC_CMD_PORT80_READ 0x0048
  
  enum ec_port80_subcmd {
  	EC_PORT80_GET_INFO = 0,
  	EC_PORT80_READ_BUFFER,
  };
  
  struct __ec_todo_packed ec_params_port80_read {
  	uint16_t subcmd;
  	union {
  		struct __ec_todo_unpacked {
  			uint32_t offset;
  			uint32_t num_entries;
  		} read_buffer;
  	};
  };
  
  struct __ec_todo_packed ec_response_port80_read {
  	union {
  		struct __ec_todo_unpacked {
  			uint32_t writes;
  			uint32_t history_size;
  			uint32_t last_boot;
  		} get_info;
  		struct __ec_todo_unpacked {
  			uint16_t codes[EC_PORT80_SIZE_MAX];
  		} data;
  	};
  };
  
  struct __ec_align2 ec_response_port80_last_boot {
  	uint16_t code;
  };
  
  /*****************************************************************************/
  /* Temporary secure storage for host verified boot use */
  
  /* Number of bytes in a vstore slot */
  #define EC_VSTORE_SLOT_SIZE 64
  
  /* Maximum number of vstore slots */
  #define EC_VSTORE_SLOT_MAX 32
  
  /* Get persistent storage info */
  #define EC_CMD_VSTORE_INFO 0x0049
  struct __ec_align_size1 ec_response_vstore_info {
  	/* Indicates which slots are locked */
  	uint32_t slot_locked;
  	/* Total number of slots available */
  	uint8_t slot_count;
  };
  
  /*
   * Read temporary secure storage
   *
   * Response is EC_VSTORE_SLOT_SIZE bytes of data.
   */
  #define EC_CMD_VSTORE_READ 0x004A
  
  struct __ec_align1 ec_params_vstore_read {
  	uint8_t slot; /* Slot to read from */
  };
  
  struct __ec_align1 ec_response_vstore_read {
  	uint8_t data[EC_VSTORE_SLOT_SIZE];
  };
  
  /*
   * Write temporary secure storage and lock it.
   */
  #define EC_CMD_VSTORE_WRITE 0x004B
  
  struct __ec_align1 ec_params_vstore_write {
  	uint8_t slot; /* Slot to write to */
  	uint8_t data[EC_VSTORE_SLOT_SIZE];
  };
  
  /*****************************************************************************/
  /* Thermal engine commands. Note that there are two implementations. We'll
   * reuse the command number, but the data and behavior is incompatible.
   * Version 0 is what originally shipped on Link.
   * Version 1 separates the CPU thermal limits from the fan control.
   */
  
  #define EC_CMD_THERMAL_SET_THRESHOLD 0x0050
  #define EC_CMD_THERMAL_GET_THRESHOLD 0x0051
  
  /* The version 0 structs are opaque. You have to know what they are for
   * the get/set commands to make any sense.
   */
  
  /* Version 0 - set */
  struct __ec_align2 ec_params_thermal_set_threshold {
  	uint8_t sensor_type;
  	uint8_t threshold_id;
  	uint16_t value;
  };
  
  /* Version 0 - get */
  struct __ec_align1 ec_params_thermal_get_threshold {
  	uint8_t sensor_type;
  	uint8_t threshold_id;
  };
  
  struct __ec_align2 ec_response_thermal_get_threshold {
  	uint16_t value;
  };
  
  
  /* The version 1 structs are visible. */
  enum ec_temp_thresholds {
  	EC_TEMP_THRESH_WARN = 0,
  	EC_TEMP_THRESH_HIGH,
  	EC_TEMP_THRESH_HALT,
  
  	EC_TEMP_THRESH_COUNT
  };
  
  /*
   * Thermal configuration for one temperature sensor. Temps are in degrees K.
   * Zero values will be silently ignored by the thermal task.
   *
   * Note that this structure is a sub-structure of
   * ec_params_thermal_set_threshold_v1, but maintains its alignment there.
   */
  struct __ec_align4 ec_thermal_config {
  	uint32_t temp_host[EC_TEMP_THRESH_COUNT]; /* levels of hotness */
  	uint32_t temp_fan_off;		/* no active cooling needed */
  	uint32_t temp_fan_max;		/* max active cooling needed */
  };
  
  /* Version 1 - get config for one sensor. */
  struct __ec_align4 ec_params_thermal_get_threshold_v1 {
  	uint32_t sensor_num;
  };
  /* This returns a struct ec_thermal_config */
  
  /* Version 1 - set config for one sensor.
   * Use read-modify-write for best results! */
  struct __ec_align4 ec_params_thermal_set_threshold_v1 {
  	uint32_t sensor_num;
  	struct ec_thermal_config cfg;
  };
  /* This returns no data */
  
  /****************************************************************************/
  
  /* Toggle automatic fan control */
  #define EC_CMD_THERMAL_AUTO_FAN_CTRL 0x0052
  
  /* Version 1 of input params */
  struct __ec_align1 ec_params_auto_fan_ctrl_v1 {
  	uint8_t fan_idx;
  };
  
  /* Get/Set TMP006 calibration data */
  #define EC_CMD_TMP006_GET_CALIBRATION 0x0053
  #define EC_CMD_TMP006_SET_CALIBRATION 0x0054
  
  /*
   * The original TMP006 calibration only needed four params, but now we need
   * more. Since the algorithm is nothing but magic numbers anyway, we'll leave
   * the params opaque. The v1 "get" response will include the algorithm number
   * and how many params it requires. That way we can change the EC code without
   * needing to update this file. We can also use a different algorithm on each
   * sensor.
   */
  
  /* This is the same struct for both v0 and v1. */
  struct __ec_align1 ec_params_tmp006_get_calibration {
  	uint8_t index;
  };
  
  /* Version 0 */
  struct __ec_align4 ec_response_tmp006_get_calibration_v0 {
  	float s0;
  	float b0;
  	float b1;
  	float b2;
  };
  
  struct __ec_align4 ec_params_tmp006_set_calibration_v0 {
  	uint8_t index;
  	uint8_t reserved[3];
  	float s0;
  	float b0;
  	float b1;
  	float b2;
  };
  
  /* Version 1 */
  struct __ec_align4 ec_response_tmp006_get_calibration_v1 {
  	uint8_t algorithm;
  	uint8_t num_params;
  	uint8_t reserved[2];
  	float val[0];
  };
  
  struct __ec_align4 ec_params_tmp006_set_calibration_v1 {
  	uint8_t index;
  	uint8_t algorithm;
  	uint8_t num_params;
  	uint8_t reserved;
  	float val[0];
  };
  
  
  /* Read raw TMP006 data */
  #define EC_CMD_TMP006_GET_RAW 0x0055
  
  struct __ec_align1 ec_params_tmp006_get_raw {
  	uint8_t index;
  };
  
  struct __ec_align4 ec_response_tmp006_get_raw {
  	int32_t t;  /* In 1/100 K */
  	int32_t v;  /* In nV */
  };
  
  /*****************************************************************************/
  /* MKBP - Matrix KeyBoard Protocol */

  
  /*
   * Read key state
   *

   * Returns raw data for keyboard cols; see ec_response_mkbp_info.cols for

   * expected response size.

   *
   * NOTE: This has been superseded by EC_CMD_MKBP_GET_NEXT_EVENT.  If you wish
   * to obtain the instantaneous state, use EC_CMD_MKBP_INFO with the type
   * EC_MKBP_INFO_CURRENT and event EC_MKBP_EVENT_KEY_MATRIX.

   */

  #define EC_CMD_MKBP_STATE 0x0060
  
  /*
   * Provide information about various MKBP things.  See enum ec_mkbp_info_type.
   */
  #define EC_CMD_MKBP_INFO 0x0061
  
  struct __ec_align_size1 ec_response_mkbp_info {
  	uint32_t rows;
  	uint32_t cols;
  	/* Formerly "switches", which was 0. */
  	uint8_t reserved;
  };
  
  struct __ec_align1 ec_params_mkbp_info {
  	uint8_t info_type;
  	uint8_t event_type;
  };
  
  enum ec_mkbp_info_type {
  	/*
  	 * Info about the keyboard matrix: number of rows and columns.
  	 *
  	 * Returns struct ec_response_mkbp_info.
  	 */
  	EC_MKBP_INFO_KBD = 0,
  
  	/*
  	 * For buttons and switches, info about which specifically are
  	 * supported.  event_type must be set to one of the values in enum
  	 * ec_mkbp_event.
  	 *
  	 * For EC_MKBP_EVENT_BUTTON and EC_MKBP_EVENT_SWITCH, returns a 4 byte
  	 * bitmask indicating which buttons or switches are present.  See the
  	 * bit inidices below.
  	 */
  	EC_MKBP_INFO_SUPPORTED = 1,
  
  	/*
  	 * Instantaneous state of buttons and switches.
  	 *
  	 * event_type must be set to one of the values in enum ec_mkbp_event.
  	 *
  	 * For EC_MKBP_EVENT_KEY_MATRIX, returns uint8_t key_matrix[13]
  	 * indicating the current state of the keyboard matrix.
  	 *
  	 * For EC_MKBP_EVENT_HOST_EVENT, return uint32_t host_event, the raw
  	 * event state.
  	 *
  	 * For EC_MKBP_EVENT_BUTTON, returns uint32_t buttons, indicating the
  	 * state of supported buttons.
  	 *
  	 * For EC_MKBP_EVENT_SWITCH, returns uint32_t switches, indicating the
  	 * state of supported switches.
  	 */
  	EC_MKBP_INFO_CURRENT = 2,
  };
  
  /* Simulate key press */
  #define EC_CMD_MKBP_SIMULATE_KEY 0x0062
  
  struct __ec_align1 ec_params_mkbp_simulate_key {
  	uint8_t col;
  	uint8_t row;
  	uint8_t pressed;
  };
  
  /* Configure keyboard scanning */
  #define EC_CMD_MKBP_SET_CONFIG 0x0064
  #define EC_CMD_MKBP_GET_CONFIG 0x0065
  
  /* flags */
  enum mkbp_config_flags {
  	EC_MKBP_FLAGS_ENABLE = 1,	/* Enable keyboard scanning */
  };
  
  enum mkbp_config_valid {
  	EC_MKBP_VALID_SCAN_PERIOD		= 1 << 0,
  	EC_MKBP_VALID_POLL_TIMEOUT		= 1 << 1,
  	EC_MKBP_VALID_MIN_POST_SCAN_DELAY	= 1 << 3,
  	EC_MKBP_VALID_OUTPUT_SETTLE		= 1 << 4,
  	EC_MKBP_VALID_DEBOUNCE_DOWN		= 1 << 5,
  	EC_MKBP_VALID_DEBOUNCE_UP		= 1 << 6,
  	EC_MKBP_VALID_FIFO_MAX_DEPTH		= 1 << 7,
  };
  
  /*
   * Configuration for our key scanning algorithm.
   *
   * Note that this is used as a sub-structure of
   * ec_{params/response}_mkbp_get_config.
   */
  struct __ec_align_size1 ec_mkbp_config {
  	uint32_t valid_mask;		/* valid fields */
  	uint8_t flags;		/* some flags (enum mkbp_config_flags) */
  	uint8_t valid_flags;		/* which flags are valid */
  	uint16_t scan_period_us;	/* period between start of scans */
  	/* revert to interrupt mode after no activity for this long */
  	uint32_t poll_timeout_us;
  	/*
  	 * minimum post-scan relax time. Once we finish a scan we check
  	 * the time until we are due to start the next one. If this time is
  	 * shorter this field, we use this instead.
  	 */
  	uint16_t min_post_scan_delay_us;
  	/* delay between setting up output and waiting for it to settle */
  	uint16_t output_settle_us;
  	uint16_t debounce_down_us;	/* time for debounce on key down */
  	uint16_t debounce_up_us;	/* time for debounce on key up */
  	/* maximum depth to allow for fifo (0 = no keyscan output) */
  	uint8_t fifo_max_depth;
  };
  
  struct __ec_align_size1 ec_params_mkbp_set_config {
  	struct ec_mkbp_config config;
  };
  
  struct __ec_align_size1 ec_response_mkbp_get_config {
  	struct ec_mkbp_config config;
  };
  
  /* Run the key scan emulation */
  #define EC_CMD_KEYSCAN_SEQ_CTRL 0x0066
  
  enum ec_keyscan_seq_cmd {
  	EC_KEYSCAN_SEQ_STATUS = 0,	/* Get status information */
  	EC_KEYSCAN_SEQ_CLEAR = 1,	/* Clear sequence */
  	EC_KEYSCAN_SEQ_ADD = 2,		/* Add item to sequence */
  	EC_KEYSCAN_SEQ_START = 3,	/* Start running sequence */
  	EC_KEYSCAN_SEQ_COLLECT = 4,	/* Collect sequence summary data */
  };
  
  enum ec_collect_flags {
  	/*
  	 * Indicates this scan was processed by the EC. Due to timing, some
  	 * scans may be skipped.
  	 */
  	EC_KEYSCAN_SEQ_FLAG_DONE	= 1 << 0,
  };
  
  struct __ec_align1 ec_collect_item {
  	uint8_t flags;		/* some flags (enum ec_collect_flags) */
  };
  
  struct __ec_todo_packed ec_params_keyscan_seq_ctrl {
  	uint8_t cmd;	/* Command to send (enum ec_keyscan_seq_cmd) */
  	union {
  		struct __ec_align1 {
  			uint8_t active;		/* still active */
  			uint8_t num_items;	/* number of items */
  			/* Current item being presented */
  			uint8_t cur_item;
  		} status;
  		struct __ec_todo_unpacked {
  			/*
  			 * Absolute time for this scan, measured from the
  			 * start of the sequence.
  			 */
  			uint32_t time_us;
  			uint8_t scan[0];	/* keyscan data */
  		} add;
  		struct __ec_align1 {
  			uint8_t start_item;	/* First item to return */
  			uint8_t num_items;	/* Number of items to return */
  		} collect;
  	};
  };
  
  struct __ec_todo_packed ec_result_keyscan_seq_ctrl {
  	union {
  		struct __ec_todo_unpacked {
  			uint8_t num_items;	/* Number of items */
  			/* Data for each item */
  			struct ec_collect_item item[0];
  		} collect;
  	};
  };
  
  /*
   * Get the next pending MKBP event.
   *
   * Returns EC_RES_UNAVAILABLE if there is no event pending.
   */
  #define EC_CMD_GET_NEXT_EVENT 0x0067
  
  enum ec_mkbp_event {
  	/* Keyboard matrix changed. The event data is the new matrix state. */
  	EC_MKBP_EVENT_KEY_MATRIX = 0,
  
  	/* New host event. The event data is 4 bytes of host event flags. */
  	EC_MKBP_EVENT_HOST_EVENT = 1,
  
  	/* New Sensor FIFO data. The event data is fifo_info structure. */
  	EC_MKBP_EVENT_SENSOR_FIFO = 2,
  
  	/* The state of the non-matrixed buttons have changed. */
  	EC_MKBP_EVENT_BUTTON = 3,
  
  	/* The state of the switches have changed. */
  	EC_MKBP_EVENT_SWITCH = 4,
  
  	/* New Fingerprint sensor event, the event data is fp_events bitmap. */
  	EC_MKBP_EVENT_FINGERPRINT = 5,
  
  	/*
  	 * Sysrq event: send emulated sysrq. The event data is sysrq,
  	 * corresponding to the key to be pressed.
  	 */
  	EC_MKBP_EVENT_SYSRQ = 6,
  
  	/* Number of MKBP events */
  	EC_MKBP_EVENT_COUNT,
  };
  
  union __ec_align_offset1 ec_response_get_next_data {
  	uint8_t key_matrix[13];
  
  	/* Unaligned */
  	uint32_t host_event;
  
  	struct __ec_todo_unpacked {
  		/* For aligning the fifo_info */
  		uint8_t reserved[3];
  		struct ec_response_motion_sense_fifo_info info;
  	} sensor_fifo;
  
  	uint32_t buttons;
  
  	uint32_t switches;
  
  	uint32_t fp_events;
  
  	uint32_t sysrq;
  };
  
  struct __ec_align1 ec_response_get_next_event {
  	uint8_t event_type;
  	/* Followed by event data if any */
  	union ec_response_get_next_data data;
  };
  
  /* Bit indices for buttons and switches.*/
  /* Buttons */
  #define EC_MKBP_POWER_BUTTON	0
  #define EC_MKBP_VOL_UP		1
  #define EC_MKBP_VOL_DOWN	2
  #define EC_MKBP_RECOVERY	3
  
  /* Switches */
  #define EC_MKBP_LID_OPEN	0
  #define EC_MKBP_TABLET_MODE	1
  
  /* Run keyboard factory test scanning */
  #define EC_CMD_KEYBOARD_FACTORY_TEST 0x0068
  
  struct __ec_align2 ec_response_keyboard_factory_test {
  	uint16_t shorted;	/* Keyboard pins are shorted */
  };
  
  /* Fingerprint events in 'fp_events' for EC_MKBP_EVENT_FINGERPRINT */
  #define EC_MKBP_FP_RAW_EVENT(fp_events) ((fp_events) & 0x00FFFFFF)
  #define EC_MKBP_FP_FINGER_DOWN          (1 << 29)
  #define EC_MKBP_FP_FINGER_UP            (1 << 30)
  #define EC_MKBP_FP_IMAGE_READY          (1 << 31)
  
  /*****************************************************************************/
  /* Temperature sensor commands */
  
  /* Read temperature sensor info */
  #define EC_CMD_TEMP_SENSOR_GET_INFO 0x0070
  
  struct __ec_align1 ec_params_temp_sensor_get_info {
  	uint8_t id;
  };
  
  struct __ec_align1 ec_response_temp_sensor_get_info {
  	char sensor_name[32];
  	uint8_t sensor_type;
  };
  
  /*****************************************************************************/
  
  /*
   * Note: host commands 0x80 - 0x87 are reserved to avoid conflict with ACPI
   * commands accidentally sent to the wrong interface.  See the ACPI section
   * below.
   */
  
  /*****************************************************************************/
  /* Host event commands */
  
  
  /* Obsolete. New implementation should use EC_CMD_PROGRAM_HOST_EVENT instead */
  /*
   * Host event mask params and response structures, shared by all of the host
   * event commands below.
   */
  struct __ec_align4 ec_params_host_event_mask {
  	uint32_t mask;
  };
  
  struct __ec_align4 ec_response_host_event_mask {
  	uint32_t mask;
  };
  
  /* These all use ec_response_host_event_mask */
  #define EC_CMD_HOST_EVENT_GET_B         0x0087
  #define EC_CMD_HOST_EVENT_GET_SMI_MASK  0x0088
  #define EC_CMD_HOST_EVENT_GET_SCI_MASK  0x0089
  #define EC_CMD_HOST_EVENT_GET_WAKE_MASK 0x008D
  
  /* These all use ec_params_host_event_mask */
  #define EC_CMD_HOST_EVENT_SET_SMI_MASK  0x008A
  #define EC_CMD_HOST_EVENT_SET_SCI_MASK  0x008B
  #define EC_CMD_HOST_EVENT_CLEAR         0x008C
  #define EC_CMD_HOST_EVENT_SET_WAKE_MASK 0x008E
  #define EC_CMD_HOST_EVENT_CLEAR_B       0x008F
  
  /*
   * Unified host event programming interface - Should be used by newer versions
   * of BIOS/OS to program host events and masks
   */
  
  struct __ec_align4 ec_params_host_event {
  
  	/* Action requested by host - one of enum ec_host_event_action. */
  	uint8_t action;
  
  	/*
  	 * Mask type that the host requested the action on - one of
  	 * enum ec_host_event_mask_type.
  	 */
  	uint8_t mask_type;
  
  	/* Set to 0, ignore on read */
  	uint16_t reserved;
  
  	/* Value to be used in case of set operations. */
  	uint64_t value;
  };
  
  /*
   * Response structure returned by EC_CMD_HOST_EVENT.
   * Update the value on a GET request. Set to 0 on GET/CLEAR
   */
  
  struct __ec_align4 ec_response_host_event {
  
  	/* Mask value in case of get operation */
  	uint64_t value;
  };
  
  enum ec_host_event_action {
  	/*
  	 * params.value is ignored. Value of mask_type populated
  	 * in response.value
  	 */
  	EC_HOST_EVENT_GET,
  
  	/* Bits in params.value are set */
  	EC_HOST_EVENT_SET,
  
  	/* Bits in params.value are cleared */
  	EC_HOST_EVENT_CLEAR,
  };
  
  enum ec_host_event_mask_type {
  
  	/* Main host event copy */
  	EC_HOST_EVENT_MAIN,
  
  	/* Copy B of host events */
  	EC_HOST_EVENT_B,
  
  	/* SCI Mask */
  	EC_HOST_EVENT_SCI_MASK,
  
  	/* SMI Mask */
  	EC_HOST_EVENT_SMI_MASK,
  
  	/* Mask of events that should be always reported in hostevents */
  	EC_HOST_EVENT_ALWAYS_REPORT_MASK,
  
  	/* Active wake mask */
  	EC_HOST_EVENT_ACTIVE_WAKE_MASK,
  
  	/* Lazy wake mask for S0ix */
  	EC_HOST_EVENT_LAZY_WAKE_MASK_S0IX,
  
  	/* Lazy wake mask for S3 */
  	EC_HOST_EVENT_LAZY_WAKE_MASK_S3,
  
  	/* Lazy wake mask for S5 */
  	EC_HOST_EVENT_LAZY_WAKE_MASK_S5,
  };
  
  #define EC_CMD_HOST_EVENT       0x00A4
  
  /*****************************************************************************/
  /* Switch commands */
  
  /* Enable/disable LCD backlight */
  #define EC_CMD_SWITCH_ENABLE_BKLIGHT 0x0090
  
  struct __ec_align1 ec_params_switch_enable_backlight {
  	uint8_t enabled;
  };
  
  /* Enable/disable WLAN/Bluetooth */
  #define EC_CMD_SWITCH_ENABLE_WIRELESS 0x0091
  #define EC_VER_SWITCH_ENABLE_WIRELESS 1
  
  /* Version 0 params; no response */
  struct __ec_align1 ec_params_switch_enable_wireless_v0 {
  	uint8_t enabled;
  };
  
  /* Version 1 params */
  struct __ec_align1 ec_params_switch_enable_wireless_v1 {
  	/* Flags to enable now */
  	uint8_t now_flags;
  
  	/* Which flags to copy from now_flags */
  	uint8_t now_mask;
  
  	/*
  	 * Flags to leave enabled in S3, if they're on at the S0->S3
  	 * transition.  (Other flags will be disabled by the S0->S3
  	 * transition.)
  	 */
  	uint8_t suspend_flags;
  
  	/* Which flags to copy from suspend_flags */
  	uint8_t suspend_mask;
  };
  
  /* Version 1 response */
  struct __ec_align1 ec_response_switch_enable_wireless_v1 {
  	/* Flags to enable now */
  	uint8_t now_flags;
  
  	/* Flags to leave enabled in S3 */
  	uint8_t suspend_flags;
  };
  
  /*****************************************************************************/
  /* GPIO commands. Only available on EC if write protect has been disabled. */
  
  /* Set GPIO output value */
  #define EC_CMD_GPIO_SET 0x0092
  
  struct __ec_align1 ec_params_gpio_set {
  	char name[32];
  	uint8_t val;
  };
  
  /* Get GPIO value */
  #define EC_CMD_GPIO_GET 0x0093
  
  /* Version 0 of input params and response */
  struct __ec_align1 ec_params_gpio_get {
  	char name[32];
  };
  
  struct __ec_align1 ec_response_gpio_get {
  	uint8_t val;
  };
  
  /* Version 1 of input params and response */
  struct __ec_align1 ec_params_gpio_get_v1 {
  	uint8_t subcmd;
  	union {
  		struct __ec_align1 {
  			char name[32];
  		} get_value_by_name;
  		struct __ec_align1 {
  			uint8_t index;
  		} get_info;
  	};
  };
  
  struct __ec_todo_packed ec_response_gpio_get_v1 {
  	union {
  		struct __ec_align1 {
  			uint8_t val;
  		} get_value_by_name, get_count;
  		struct __ec_todo_unpacked {
  			uint8_t val;
  			char name[32];
  			uint32_t flags;
  		} get_info;
  	};
  };
  
  enum gpio_get_subcmd {
  	EC_GPIO_GET_BY_NAME = 0,
  	EC_GPIO_GET_COUNT = 1,
  	EC_GPIO_GET_INFO = 2,
  };
  
  /*****************************************************************************/
  /* I2C commands. Only available when flash write protect is unlocked. */
  
  /*
   * CAUTION: These commands are deprecated, and are not supported anymore in EC
   * builds >= 8398.0.0 (see crosbug.com/p/23570).
   *
   * Use EC_CMD_I2C_PASSTHRU instead.
   */
  
  /* Read I2C bus */
  #define EC_CMD_I2C_READ 0x0094
  
  struct __ec_align_size1 ec_params_i2c_read {
  	uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
  	uint8_t read_size; /* Either 8 or 16. */
  	uint8_t port;
  	uint8_t offset;
  };
  
  struct __ec_align2 ec_response_i2c_read {
  	uint16_t data;
  };
  
  /* Write I2C bus */
  #define EC_CMD_I2C_WRITE 0x0095
  
  struct __ec_align_size1 ec_params_i2c_write {
  	uint16_t data;
  	uint16_t addr; /* 8-bit address (7-bit shifted << 1) */
  	uint8_t write_size; /* Either 8 or 16. */
  	uint8_t port;
  	uint8_t offset;
  };
  
  /*****************************************************************************/
  /* Charge state commands. Only available when flash write protect unlocked. */
  
  /* Force charge state machine to stop charging the battery or force it to
   * discharge the battery.
   */
  #define EC_CMD_CHARGE_CONTROL 0x0096
  #define EC_VER_CHARGE_CONTROL 1
  
  enum ec_charge_control_mode {
  	CHARGE_CONTROL_NORMAL = 0,
  	CHARGE_CONTROL_IDLE,
  	CHARGE_CONTROL_DISCHARGE,
  };
  
  struct __ec_align4 ec_params_charge_control {
  	uint32_t mode;  /* enum charge_control_mode */
  };
  
  /*****************************************************************************/
  /* Console commands. Only available when flash write protect is unlocked. */
  
  /* Snapshot console output buffer for use by EC_CMD_CONSOLE_READ. */
  #define EC_CMD_CONSOLE_SNAPSHOT 0x0097
  
  /*
   * Read data from the saved snapshot. If the subcmd parameter is
   * CONSOLE_READ_NEXT, this will return data starting from the beginning of
   * the latest snapshot. If it is CONSOLE_READ_RECENT, it will start from the
   * end of the previous snapshot.
   *
   * The params are only looked at in version >= 1 of this command. Prior
   * versions will just default to CONSOLE_READ_NEXT behavior.
   *
   * Response is null-terminated string.  Empty string, if there is no more
   * remaining output.
   */
  #define EC_CMD_CONSOLE_READ 0x0098
  
  enum ec_console_read_subcmd {
  	CONSOLE_READ_NEXT = 0,
  	CONSOLE_READ_RECENT
  };
  
  struct __ec_align1 ec_params_console_read_v1 {
  	uint8_t subcmd; /* enum ec_console_read_subcmd */
  };
  
  /*****************************************************************************/
  
  /*
   * Cut off battery power immediately or after the host has shut down.
   *
   * return EC_RES_INVALID_COMMAND if unsupported by a board/battery.
   *	  EC_RES_SUCCESS if the command was successful.
   *	  EC_RES_ERROR if the cut off command failed.
   */
  #define EC_CMD_BATTERY_CUT_OFF 0x0099
  
  #define EC_BATTERY_CUTOFF_FLAG_AT_SHUTDOWN	(1 << 0)
  
  struct __ec_align1 ec_params_battery_cutoff {
  	uint8_t flags;
  };
  
  /*****************************************************************************/
  /* USB port mux control. */
  
  /*
   * Switch USB mux or return to automatic switching.
   */
  #define EC_CMD_USB_MUX 0x009A
  
  struct __ec_align1 ec_params_usb_mux {
  	uint8_t mux;
  };
  
  /*****************************************************************************/
  /* LDOs / FETs control. */
  
  enum ec_ldo_state {
  	EC_LDO_STATE_OFF = 0,	/* the LDO / FET is shut down */
  	EC_LDO_STATE_ON = 1,	/* the LDO / FET is ON / providing power */
  };
  
  /*
   * Switch on/off a LDO.
   */
  #define EC_CMD_LDO_SET 0x009B
  
  struct __ec_align1 ec_params_ldo_set {
  	uint8_t index;
  	uint8_t state;
  };
  
  /*
   * Get LDO state.
   */
  #define EC_CMD_LDO_GET 0x009C
  
  struct __ec_align1 ec_params_ldo_get {
  	uint8_t index;
  };
  
  struct __ec_align1 ec_response_ldo_get {
  	uint8_t state;
  };
  
  /*****************************************************************************/
  /* Power info. */
  
  /*
   * Get power info.
   */
  #define EC_CMD_POWER_INFO 0x009D
  
  struct __ec_align4 ec_response_power_info {
  	uint32_t usb_dev_type;
  	uint16_t voltage_ac;
  	uint16_t voltage_system;
  	uint16_t current_system;
  	uint16_t usb_current_limit;
  };
  
  /*****************************************************************************/
  /* I2C passthru command */
  
  #define EC_CMD_I2C_PASSTHRU 0x009E
  
  /* Read data; if not present, message is a write */
  #define EC_I2C_FLAG_READ	(1 << 15)
  
  /* Mask for address */
  #define EC_I2C_ADDR_MASK	0x3ff
  
  #define EC_I2C_STATUS_NAK	(1 << 0) /* Transfer was not acknowledged */
  #define EC_I2C_STATUS_TIMEOUT	(1 << 1) /* Timeout during transfer */
  
  /* Any error */
  #define EC_I2C_STATUS_ERROR	(EC_I2C_STATUS_NAK | EC_I2C_STATUS_TIMEOUT)
  
  struct __ec_align2 ec_params_i2c_passthru_msg {
  	uint16_t addr_flags;	/* I2C slave address (7 or 10 bits) and flags */
  	uint16_t len;		/* Number of bytes to read or write */
  };
  
  struct __ec_align2 ec_params_i2c_passthru {
  	uint8_t port;		/* I2C port number */
  	uint8_t num_msgs;	/* Number of messages */
  	struct ec_params_i2c_passthru_msg msg[];
  	/* Data to write for all messages is concatenated here */
  };
  
  struct __ec_align1 ec_response_i2c_passthru {
  	uint8_t i2c_status;	/* Status flags (EC_I2C_STATUS_...) */
  	uint8_t num_msgs;	/* Number of messages processed */
  	uint8_t data[];		/* Data read by messages concatenated here */
  };
  
  /*****************************************************************************/
  /* Power button hang detect */
  
  #define EC_CMD_HANG_DETECT 0x009F
  
  /* Reasons to start hang detection timer */
  /* Power button pressed */
  #define EC_HANG_START_ON_POWER_PRESS  (1 << 0)
  
  /* Lid closed */
  #define EC_HANG_START_ON_LID_CLOSE    (1 << 1)
  
   /* Lid opened */
  #define EC_HANG_START_ON_LID_OPEN     (1 << 2)
  
  /* Start of AP S3->S0 transition (booting or resuming from suspend) */
  #define EC_HANG_START_ON_RESUME       (1 << 3)
  
  /* Reasons to cancel hang detection */
  
  /* Power button released */
  #define EC_HANG_STOP_ON_POWER_RELEASE (1 << 8)
  
  /* Any host command from AP received */
  #define EC_HANG_STOP_ON_HOST_COMMAND  (1 << 9)
  
  /* Stop on end of AP S0->S3 transition (suspending or shutting down) */
  #define EC_HANG_STOP_ON_SUSPEND       (1 << 10)
  
  /*
   * If this flag is set, all the other fields are ignored, and the hang detect
   * timer is started.  This provides the AP a way to start the hang timer
   * without reconfiguring any of the other hang detect settings.  Note that
   * you must previously have configured the timeouts.
   */
  #define EC_HANG_START_NOW             (1 << 30)
  
  /*
   * If this flag is set, all the other fields are ignored (including
   * EC_HANG_START_NOW).  This provides the AP a way to stop the hang timer
   * without reconfiguring any of the other hang detect settings.
   */
  #define EC_HANG_STOP_NOW              (1 << 31)
  
  struct __ec_align4 ec_params_hang_detect {
  	/* Flags; see EC_HANG_* */
  	uint32_t flags;
  
  	/* Timeout in msec before generating host event, if enabled */
  	uint16_t host_event_timeout_msec;
  
  	/* Timeout in msec before generating warm reboot, if enabled */
  	uint16_t warm_reboot_timeout_msec;
  };
  
  /*****************************************************************************/
  /* Commands for battery charging */
  
  /*
   * This is the single catch-all host command to exchange data regarding the
   * charge state machine (v2 and up).
   */
  #define EC_CMD_CHARGE_STATE 0x00A0
  
  /* Subcommands for this host command */
  enum charge_state_command {
  	CHARGE_STATE_CMD_GET_STATE,
  	CHARGE_STATE_CMD_GET_PARAM,
  	CHARGE_STATE_CMD_SET_PARAM,
  	CHARGE_STATE_NUM_CMDS
  };
  
  /*
   * Known param numbers are defined here. Ranges are reserved for board-specific
   * params, which are handled by the particular implementations.
   */
  enum charge_state_params {
  	CS_PARAM_CHG_VOLTAGE,	      /* charger voltage limit */
  	CS_PARAM_CHG_CURRENT,	      /* charger current limit */
  	CS_PARAM_CHG_INPUT_CURRENT,   /* charger input current limit */
  	CS_PARAM_CHG_STATUS,	      /* charger-specific status */
  	CS_PARAM_CHG_OPTION,	      /* charger-specific options */
  	CS_PARAM_LIMIT_POWER,	      /*
  				       * Check if power is limited due to
  				       * low battery and / or a weak external
  				       * charger. READ ONLY.
  				       */
  	/* How many so far? */
  	CS_NUM_BASE_PARAMS,
  
  	/* Range for CONFIG_CHARGER_PROFILE_OVERRIDE params */
  	CS_PARAM_CUSTOM_PROFILE_MIN = 0x10000,
  	CS_PARAM_CUSTOM_PROFILE_MAX = 0x1ffff,
  
  	/* Other custom param ranges go here... */
  };
  
  struct __ec_todo_packed ec_params_charge_state {
  	uint8_t cmd;				/* enum charge_state_command */
  	union {
  		struct __ec_align1 {
  			/* no args */
  		} get_state;
  
  		struct __ec_todo_unpacked {
  			uint32_t param;		/* enum charge_state_param */
  		} get_param;
  
  		struct __ec_todo_unpacked {
  			uint32_t param;		/* param to set */
  			uint32_t value;		/* value to set */
  		} set_param;
  	};
  };
  
  struct __ec_align4 ec_response_charge_state {
  	union {
  		struct __ec_align4 {
  			int ac;
  			int chg_voltage;
  			int chg_current;
  			int chg_input_current;
  			int batt_state_of_charge;
  		} get_state;
  
  		struct __ec_align4 {
  			uint32_t value;
  		} get_param;
  		struct __ec_align4 {
  			/* no return values */
  		} set_param;
  	};
  };
  
  
  /*
   * Set maximum battery charging current.
   */
  #define EC_CMD_CHARGE_CURRENT_LIMIT 0x00A1
  
  struct __ec_align4 ec_params_current_limit {
  	uint32_t limit; /* in mA */
  };
  
  /*
   * Set maximum external voltage / current.
   */
  #define EC_CMD_EXTERNAL_POWER_LIMIT 0x00A2
  
  /* Command v0 is used only on Spring and is obsolete + unsupported */
  struct __ec_align2 ec_params_external_power_limit_v1 {
  	uint16_t current_lim; /* in mA, or EC_POWER_LIMIT_NONE to clear limit */
  	uint16_t voltage_lim; /* in mV, or EC_POWER_LIMIT_NONE to clear limit */
  };
  
  #define EC_POWER_LIMIT_NONE 0xffff
  
  /*
   * Set maximum voltage & current of a dedicated charge port
   */
  #define EC_CMD_OVERRIDE_DEDICATED_CHARGER_LIMIT 0x00A3
  
  struct __ec_align2 ec_params_dedicated_charger_limit {
  	uint16_t current_lim; /* in mA */
  	uint16_t voltage_lim; /* in mV */
  };
  
  /*****************************************************************************/
  /* Hibernate/Deep Sleep Commands */
  
  /* Set the delay before going into hibernation. */
  #define EC_CMD_HIBERNATION_DELAY 0x00A8
  
  struct __ec_align4 ec_params_hibernation_delay {
  	/*
  	 * Seconds to wait in G3 before hibernate.  Pass in 0 to read the
  	 * current settings without changing them.
  	 */
  	uint32_t seconds;
  };
  
  struct __ec_align4 ec_response_hibernation_delay {
  	/*
  	 * The current time in seconds in which the system has been in the G3
  	 * state.  This value is reset if the EC transitions out of G3.
  	 */
  	uint32_t time_g3;
  
  	/*
  	 * The current time remaining in seconds until the EC should hibernate.
  	 * This value is also reset if the EC transitions out of G3.
  	 */
  	uint32_t time_remaining;
  
  	/*
  	 * The current time in seconds that the EC should wait in G3 before
  	 * hibernating.
  	 */
  	uint32_t hibernate_delay;
  };
  
  /* Inform the EC when entering a sleep state */
  #define EC_CMD_HOST_SLEEP_EVENT 0x00A9
  
  enum host_sleep_event {
  	HOST_SLEEP_EVENT_S3_SUSPEND   = 1,
  	HOST_SLEEP_EVENT_S3_RESUME    = 2,
  	HOST_SLEEP_EVENT_S0IX_SUSPEND = 3,
  	HOST_SLEEP_EVENT_S0IX_RESUME  = 4
  };
  
  struct __ec_align1 ec_params_host_sleep_event {
  	uint8_t sleep_event;
  };
  
  /*****************************************************************************/
  /* Device events */
  #define EC_CMD_DEVICE_EVENT 0x00AA
  
  enum ec_device_event {
  	EC_DEVICE_EVENT_TRACKPAD,
  	EC_DEVICE_EVENT_DSP,
  	EC_DEVICE_EVENT_WIFI,
  };
  
  enum ec_device_event_param {
  	/* Get and clear pending device events */
  	EC_DEVICE_EVENT_PARAM_GET_CURRENT_EVENTS,
  	/* Get device event mask */
  	EC_DEVICE_EVENT_PARAM_GET_ENABLED_EVENTS,
  	/* Set device event mask */
  	EC_DEVICE_EVENT_PARAM_SET_ENABLED_EVENTS,
  };
  
  #define EC_DEVICE_EVENT_MASK(event_code) (1UL << (event_code % 32))

  struct __ec_align_size1 ec_params_device_event {
  	uint32_t event_mask;
  	uint8_t param;
  };

  struct __ec_align4 ec_response_device_event {
  	uint32_t event_mask;
  };

  /*****************************************************************************/
  /* Smart battery pass-through */

  /* Get / Set 16-bit smart battery registers */
  #define EC_CMD_SB_READ_WORD   0x00B0
  #define EC_CMD_SB_WRITE_WORD  0x00B1

  /* Get / Set string smart battery parameters
   * formatted as SMBUS "block".
   */
  #define EC_CMD_SB_READ_BLOCK  0x00B2
  #define EC_CMD_SB_WRITE_BLOCK 0x00B3

  struct __ec_align1 ec_params_sb_rd {
  	uint8_t reg;

  };

  struct __ec_align2 ec_response_sb_rd_word {
  	uint16_t value;

  };

  struct __ec_align1 ec_params_sb_wr_word {
  	uint8_t reg;
  	uint16_t value;
  };

  struct __ec_align1 ec_response_sb_rd_block {
  	uint8_t data[32];
  };

  struct __ec_align1 ec_params_sb_wr_block {
  	uint8_t reg;
  	uint16_t data[32];
  };

  /*****************************************************************************/
  /* Battery vendor parameters
   *
   * Get or set vendor-specific parameters in the battery. Implementations may
   * differ between boards or batteries. On a set operation, the response
   * contains the actual value set, which may be rounded or clipped from the
   * requested value.
   */

  #define EC_CMD_BATTERY_VENDOR_PARAM 0x00B4
  
  enum ec_battery_vendor_param_mode {
  	BATTERY_VENDOR_PARAM_MODE_GET = 0,
  	BATTERY_VENDOR_PARAM_MODE_SET,

  };

  struct __ec_align_size1 ec_params_battery_vendor_param {
  	uint32_t param;
  	uint32_t value;
  	uint8_t mode;

  };

  struct __ec_align4 ec_response_battery_vendor_param {
  	uint32_t value;

  };

  /*****************************************************************************/
  /*
   * Smart Battery Firmware Update Commands
   */
  #define EC_CMD_SB_FW_UPDATE 0x00B5
  
  enum ec_sb_fw_update_subcmd {
  	EC_SB_FW_UPDATE_PREPARE  = 0x0,
  	EC_SB_FW_UPDATE_INFO     = 0x1, /*query sb info */
  	EC_SB_FW_UPDATE_BEGIN    = 0x2, /*check if protected */
  	EC_SB_FW_UPDATE_WRITE    = 0x3, /*check if protected */
  	EC_SB_FW_UPDATE_END      = 0x4,
  	EC_SB_FW_UPDATE_STATUS   = 0x5,
  	EC_SB_FW_UPDATE_PROTECT  = 0x6,
  	EC_SB_FW_UPDATE_MAX      = 0x7,
  };
  
  #define SB_FW_UPDATE_CMD_WRITE_BLOCK_SIZE 32
  #define SB_FW_UPDATE_CMD_STATUS_SIZE 2
  #define SB_FW_UPDATE_CMD_INFO_SIZE 8
  
  struct __ec_align4 ec_sb_fw_update_header {
  	uint16_t subcmd;  /* enum ec_sb_fw_update_subcmd */
  	uint16_t fw_id;   /* firmware id */
  };
  
  struct __ec_align4 ec_params_sb_fw_update {
  	struct ec_sb_fw_update_header hdr;

  	union {

  		/* EC_SB_FW_UPDATE_PREPARE  = 0x0 */
  		/* EC_SB_FW_UPDATE_INFO     = 0x1 */
  		/* EC_SB_FW_UPDATE_BEGIN    = 0x2 */
  		/* EC_SB_FW_UPDATE_END      = 0x4 */
  		/* EC_SB_FW_UPDATE_STATUS   = 0x5 */
  		/* EC_SB_FW_UPDATE_PROTECT  = 0x6 */
  		struct __ec_align4 {
  			/* no args */
  		} dummy;
  
  		/* EC_SB_FW_UPDATE_WRITE    = 0x3 */
  		struct __ec_align4 {
  			uint8_t  data[SB_FW_UPDATE_CMD_WRITE_BLOCK_SIZE];
  		} write;

  	};

  };

  struct __ec_align1 ec_response_sb_fw_update {

  	union {

  		/* EC_SB_FW_UPDATE_INFO     = 0x1 */
  		struct __ec_align1 {
  			uint8_t data[SB_FW_UPDATE_CMD_INFO_SIZE];
  		} info;
  
  		/* EC_SB_FW_UPDATE_STATUS   = 0x5 */
  		struct __ec_align1 {
  			uint8_t data[SB_FW_UPDATE_CMD_STATUS_SIZE];
  		} status;

  	};

  };
  
  /*
   * Entering Verified Boot Mode Command
   * Default mode is VBOOT_MODE_NORMAL if EC did not receive this command.
   * Valid Modes are: normal, developer, and recovery.
   */
  #define EC_CMD_ENTERING_MODE 0x00B6
  
  struct __ec_align4 ec_params_entering_mode {
  	int vboot_mode;
  };
  
  #define VBOOT_MODE_NORMAL    0
  #define VBOOT_MODE_DEVELOPER 1
  #define VBOOT_MODE_RECOVERY  2

  
  /*****************************************************************************/

  /*
   * I2C passthru protection command: Protects I2C tunnels against access on
   * certain addresses (board-specific).
   */
  #define EC_CMD_I2C_PASSTHRU_PROTECT 0x00B7

  enum ec_i2c_passthru_protect_subcmd {
  	EC_CMD_I2C_PASSTHRU_PROTECT_STATUS = 0x0,
  	EC_CMD_I2C_PASSTHRU_PROTECT_ENABLE = 0x1,
  };

  struct __ec_align1 ec_params_i2c_passthru_protect {
  	uint8_t subcmd;
  	uint8_t port;		/* I2C port number */
  };

  struct __ec_align1 ec_response_i2c_passthru_protect {
  	uint8_t status;		/* Status flags (0: unlocked, 1: locked) */
  };

  
  /*****************************************************************************/

  /* System commands */

  
  /*

   * TODO(crosbug.com/p/23747): This is a confusing name, since it doesn't
   * necessarily reboot the EC.  Rename to "image" or something similar?

   */

  #define EC_CMD_REBOOT_EC 0x00D2

  /* Command */
  enum ec_reboot_cmd {
  	EC_REBOOT_CANCEL = 0,        /* Cancel a pending reboot */
  	EC_REBOOT_JUMP_RO = 1,       /* Jump to RO without rebooting */
  	EC_REBOOT_JUMP_RW = 2,       /* Jump to RW without rebooting */
  	/* (command 3 was jump to RW-B) */
  	EC_REBOOT_COLD = 4,          /* Cold-reboot */
  	EC_REBOOT_DISABLE_JUMP = 5,  /* Disable jump until next reboot */
  	EC_REBOOT_HIBERNATE = 6,     /* Hibernate EC */
  	EC_REBOOT_HIBERNATE_CLEAR_AP_OFF = 7, /* and clears AP_OFF flag */
  };
  
  /* Flags for ec_params_reboot_ec.reboot_flags */
  #define EC_REBOOT_FLAG_RESERVED0      (1 << 0)  /* Was recovery request */
  #define EC_REBOOT_FLAG_ON_AP_SHUTDOWN (1 << 1)  /* Reboot after AP shutdown */
  #define EC_REBOOT_FLAG_SWITCH_RW_SLOT (1 << 2)  /* Switch RW slot */
  
  struct __ec_align1 ec_params_reboot_ec {
  	uint8_t cmd;           /* enum ec_reboot_cmd */
  	uint8_t flags;         /* See EC_REBOOT_FLAG_* */
  };

  
  /*

   * Get information on last EC panic.
   *
   * Returns variable-length platform-dependent panic information.  See panic.h
   * for details.

   */

  #define EC_CMD_GET_PANIC_INFO 0x00D3

  /*****************************************************************************/
  /*
   * Special commands
   *
   * These do not follow the normal rules for commands.  See each command for
   * details.
   */

  /*
   * Reboot NOW
   *
   * This command will work even when the EC LPC interface is busy, because the
   * reboot command is processed at interrupt level.  Note that when the EC
   * reboots, the host will reboot too, so there is no response to this command.
   *
   * Use EC_CMD_REBOOT_EC to reboot the EC more politely.
   */
  #define EC_CMD_REBOOT 0x00D1  /* Think "die" */

  /*
   * Resend last response (not supported on LPC).
   *
   * Returns EC_RES_UNAVAILABLE if there is no response available - for example,
   * there was no previous command, or the previous command's response was too
   * big to save.
   */
  #define EC_CMD_RESEND_RESPONSE 0x00DB
  
  /*
   * This header byte on a command indicate version 0. Any header byte less
   * than this means that we are talking to an old EC which doesn't support
   * versioning. In that case, we assume version 0.
   *
   * Header bytes greater than this indicate a later version. For example,
   * EC_CMD_VERSION0 + 1 means we are using version 1.
   *
   * The old EC interface must not use commands 0xdc or higher.
   */
  #define EC_CMD_VERSION0 0x00DC

  
  /*****************************************************************************/

  /*
   * PD commands
   *
   * These commands are for PD MCU communication.
   */

  /* EC to PD MCU exchange status command */
  #define EC_CMD_PD_EXCHANGE_STATUS 0x0100
  #define EC_VER_PD_EXCHANGE_STATUS 2

  enum pd_charge_state {
  	PD_CHARGE_NO_CHANGE = 0, /* Don't change charge state */
  	PD_CHARGE_NONE,          /* No charging allowed */
  	PD_CHARGE_5V,            /* 5V charging only */
  	PD_CHARGE_MAX            /* Charge at max voltage */
  };

  /* Status of EC being sent to PD */
  #define EC_STATUS_HIBERNATING	(1 << 0)
  
  struct __ec_align1 ec_params_pd_status {
  	uint8_t status;       /* EC status */
  	int8_t batt_soc;      /* battery state of charge */
  	uint8_t charge_state; /* charging state (from enum pd_charge_state) */
  };
  
  /* Status of PD being sent back to EC */
  #define PD_STATUS_HOST_EVENT      (1 << 0) /* Forward host event to AP */
  #define PD_STATUS_IN_RW           (1 << 1) /* Running RW image */
  #define PD_STATUS_JUMPED_TO_IMAGE (1 << 2) /* Current image was jumped to */
  #define PD_STATUS_TCPC_ALERT_0    (1 << 3) /* Alert active in port 0 TCPC */
  #define PD_STATUS_TCPC_ALERT_1    (1 << 4) /* Alert active in port 1 TCPC */
  #define PD_STATUS_TCPC_ALERT_2    (1 << 5) /* Alert active in port 2 TCPC */
  #define PD_STATUS_TCPC_ALERT_3    (1 << 6) /* Alert active in port 3 TCPC */
  #define PD_STATUS_EC_INT_ACTIVE  (PD_STATUS_TCPC_ALERT_0 | \
  				      PD_STATUS_TCPC_ALERT_1 | \
  				      PD_STATUS_HOST_EVENT)
  struct __ec_align_size1 ec_response_pd_status {
  	uint32_t curr_lim_ma;       /* input current limit */
  	uint16_t status;            /* PD MCU status */
  	int8_t active_charge_port;  /* active charging port */
  };
  
  /* AP to PD MCU host event status command, cleared on read */
  #define EC_CMD_PD_HOST_EVENT_STATUS 0x0104
  
  /* PD MCU host event status bits */
  #define PD_EVENT_UPDATE_DEVICE     (1 << 0)
  #define PD_EVENT_POWER_CHANGE      (1 << 1)
  #define PD_EVENT_IDENTITY_RECEIVED (1 << 2)
  #define PD_EVENT_DATA_SWAP         (1 << 3)
  struct __ec_align4 ec_response_host_event_status {
  	uint32_t status;      /* PD MCU host event status */
  };
  
  /* Set USB type-C port role and muxes */
  #define EC_CMD_USB_PD_CONTROL 0x0101
  
  enum usb_pd_control_role {
  	USB_PD_CTRL_ROLE_NO_CHANGE = 0,
  	USB_PD_CTRL_ROLE_TOGGLE_ON = 1, /* == AUTO */
  	USB_PD_CTRL_ROLE_TOGGLE_OFF = 2,
  	USB_PD_CTRL_ROLE_FORCE_SINK = 3,
  	USB_PD_CTRL_ROLE_FORCE_SOURCE = 4,
  	USB_PD_CTRL_ROLE_COUNT
  };
  
  enum usb_pd_control_mux {
  	USB_PD_CTRL_MUX_NO_CHANGE = 0,
  	USB_PD_CTRL_MUX_NONE = 1,
  	USB_PD_CTRL_MUX_USB = 2,
  	USB_PD_CTRL_MUX_DP = 3,
  	USB_PD_CTRL_MUX_DOCK = 4,
  	USB_PD_CTRL_MUX_AUTO = 5,
  	USB_PD_CTRL_MUX_COUNT
  };
  
  enum usb_pd_control_swap {
  	USB_PD_CTRL_SWAP_NONE = 0,
  	USB_PD_CTRL_SWAP_DATA = 1,
  	USB_PD_CTRL_SWAP_POWER = 2,
  	USB_PD_CTRL_SWAP_VCONN = 3,
  	USB_PD_CTRL_SWAP_COUNT
  };
  
  struct __ec_align1 ec_params_usb_pd_control {
  	uint8_t port;
  	uint8_t role;
  	uint8_t mux;
  	uint8_t swap;
  };

  #define PD_CTRL_RESP_ENABLED_COMMS      (1 << 0) /* Communication enabled */
  #define PD_CTRL_RESP_ENABLED_CONNECTED  (1 << 1) /* Device connected */
  #define PD_CTRL_RESP_ENABLED_PD_CAPABLE (1 << 2) /* Partner is PD capable */
  
  #define PD_CTRL_RESP_ROLE_POWER         (1 << 0) /* 0=SNK/1=SRC */
  #define PD_CTRL_RESP_ROLE_DATA          (1 << 1) /* 0=UFP/1=DFP */
  #define PD_CTRL_RESP_ROLE_VCONN         (1 << 2) /* Vconn status */
  #define PD_CTRL_RESP_ROLE_DR_POWER      (1 << 3) /* Partner is dualrole power */
  #define PD_CTRL_RESP_ROLE_DR_DATA       (1 << 4) /* Partner is dualrole data */
  #define PD_CTRL_RESP_ROLE_USB_COMM      (1 << 5) /* Partner USB comm capable */
  #define PD_CTRL_RESP_ROLE_EXT_POWERED   (1 << 6) /* Partner externally powerd */
  
  struct __ec_align1 ec_response_usb_pd_control {

  	uint8_t enabled;

  	uint8_t role;
  	uint8_t polarity;
  	uint8_t state;
  };

  struct __ec_align1 ec_response_usb_pd_control_v1 {
  	uint8_t enabled;
  	uint8_t role;
  	uint8_t polarity;
  	char state[32];
  };

  #define EC_CMD_USB_PD_PORTS 0x0102

  /* Maximum number of PD ports on a device, num_ports will be <= this */
  #define EC_USB_PD_MAX_PORTS 8

  struct __ec_align1 ec_response_usb_pd_ports {
  	uint8_t num_ports;
  };

  #define EC_CMD_USB_PD_POWER_INFO 0x0103
  
  #define PD_POWER_CHARGING_PORT 0xff
  struct __ec_align1 ec_params_usb_pd_power_info {
  	uint8_t port;
  };
  
  enum usb_chg_type {
  	USB_CHG_TYPE_NONE,
  	USB_CHG_TYPE_PD,
  	USB_CHG_TYPE_C,
  	USB_CHG_TYPE_PROPRIETARY,
  	USB_CHG_TYPE_BC12_DCP,
  	USB_CHG_TYPE_BC12_CDP,
  	USB_CHG_TYPE_BC12_SDP,
  	USB_CHG_TYPE_OTHER,
  	USB_CHG_TYPE_VBUS,
  	USB_CHG_TYPE_UNKNOWN,
  };
  enum usb_power_roles {
  	USB_PD_PORT_POWER_DISCONNECTED,
  	USB_PD_PORT_POWER_SOURCE,
  	USB_PD_PORT_POWER_SINK,
  	USB_PD_PORT_POWER_SINK_NOT_CHARGING,
  };
  
  struct __ec_align2 usb_chg_measures {
  	uint16_t voltage_max;
  	uint16_t voltage_now;
  	uint16_t current_max;
  	uint16_t current_lim;
  };
  
  struct __ec_align4 ec_response_usb_pd_power_info {
  	uint8_t role;
  	uint8_t type;
  	uint8_t dualrole;
  	uint8_t reserved1;
  	struct usb_chg_measures meas;
  	uint32_t max_power;
  };
  
  /* Write USB-PD device FW */
  #define EC_CMD_USB_PD_FW_UPDATE 0x0110
  
  enum usb_pd_fw_update_cmds {
  	USB_PD_FW_REBOOT,
  	USB_PD_FW_FLASH_ERASE,
  	USB_PD_FW_FLASH_WRITE,
  	USB_PD_FW_ERASE_SIG,
  };
  
  struct __ec_align4 ec_params_usb_pd_fw_update {
  	uint16_t dev_id;
  	uint8_t cmd;
  	uint8_t port;
  	uint32_t size;     /* Size to write in bytes */
  	/* Followed by data to write */
  };

  /* Write USB-PD Accessory RW_HASH table entry */
  #define EC_CMD_USB_PD_RW_HASH_ENTRY 0x0111
  /* RW hash is first 20 bytes of SHA-256 of RW section */
  #define PD_RW_HASH_SIZE 20
  struct __ec_align1 ec_params_usb_pd_rw_hash_entry {
  	uint16_t dev_id;
  	uint8_t dev_rw_hash[PD_RW_HASH_SIZE];
  	uint8_t reserved;        /* For alignment of current_image
  				  * TODO(rspangler) but it's not aligned!
  				  * Should have been reserved[2]. */
  	uint32_t current_image;  /* One of ec_current_image */
  };

  /* Read USB-PD Accessory info */
  #define EC_CMD_USB_PD_DEV_INFO 0x0112

  struct __ec_align1 ec_params_usb_pd_info_request {

  	uint8_t port;

  };

  /* Read USB-PD Device discovery info */
  #define EC_CMD_USB_PD_DISCOVERY 0x0113
  struct __ec_align_size1 ec_params_usb_pd_discovery_entry {
  	uint16_t vid;  /* USB-IF VID */
  	uint16_t pid;  /* USB-IF PID */
  	uint8_t ptype; /* product type (hub,periph,cable,ama) */
  };

  /* Override default charge behavior */
  #define EC_CMD_PD_CHARGE_PORT_OVERRIDE 0x0114

  /* Negative port parameters have special meaning */
  enum usb_pd_override_ports {
  	OVERRIDE_DONT_CHARGE = -2,
  	OVERRIDE_OFF = -1,
  	/* [0, CONFIG_USB_PD_PORT_COUNT): Port# */
  };

  struct __ec_align2 ec_params_charge_port_override {
  	int16_t override_port; /* Override port# */
  };

  /* Read (and delete) one entry of PD event log */
  #define EC_CMD_PD_GET_LOG_ENTRY 0x0115

  struct __ec_align4 ec_response_pd_log {
  	uint32_t timestamp; /* relative timestamp in milliseconds */
  	uint8_t type;       /* event type : see PD_EVENT_xx below */
  	uint8_t size_port;  /* [7:5] port number [4:0] payload size in bytes */
  	uint16_t data;      /* type-defined data payload */
  	uint8_t payload[0]; /* optional additional data payload: 0..16 bytes */
  };

  
  /* The timestamp is the microsecond counter shifted to get about a ms. */
  #define PD_LOG_TIMESTAMP_SHIFT 10 /* 1 LSB = 1024us */
  
  #define PD_LOG_SIZE_MASK  0x1f
  #define PD_LOG_PORT_MASK  0xe0
  #define PD_LOG_PORT_SHIFT    5
  #define PD_LOG_PORT_SIZE(port, size) (((port) << PD_LOG_PORT_SHIFT) | \
  				      ((size) & PD_LOG_SIZE_MASK))
  #define PD_LOG_PORT(size_port) ((size_port) >> PD_LOG_PORT_SHIFT)
  #define PD_LOG_SIZE(size_port) ((size_port) & PD_LOG_SIZE_MASK)
  
  /* PD event log : entry types */
  /* PD MCU events */
  #define PD_EVENT_MCU_BASE       0x00
  #define PD_EVENT_MCU_CHARGE             (PD_EVENT_MCU_BASE+0)
  #define PD_EVENT_MCU_CONNECT            (PD_EVENT_MCU_BASE+1)
  /* Reserved for custom board event */
  #define PD_EVENT_MCU_BOARD_CUSTOM       (PD_EVENT_MCU_BASE+2)
  /* PD generic accessory events */
  #define PD_EVENT_ACC_BASE       0x20
  #define PD_EVENT_ACC_RW_FAIL   (PD_EVENT_ACC_BASE+0)
  #define PD_EVENT_ACC_RW_ERASE  (PD_EVENT_ACC_BASE+1)
  /* PD power supply events */
  #define PD_EVENT_PS_BASE        0x40
  #define PD_EVENT_PS_FAULT      (PD_EVENT_PS_BASE+0)
  /* PD video dongles events */
  #define PD_EVENT_VIDEO_BASE     0x60
  #define PD_EVENT_VIDEO_DP_MODE (PD_EVENT_VIDEO_BASE+0)
  #define PD_EVENT_VIDEO_CODEC   (PD_EVENT_VIDEO_BASE+1)
  /* Returned in the "type" field, when there is no entry available */
  #define PD_EVENT_NO_ENTRY       0xff

  
  /*

   * PD_EVENT_MCU_CHARGE event definition :
   * the payload is "struct usb_chg_measures"
   * the data field contains the port state flags as defined below :

   */

  /* Port partner is a dual role device */
  #define CHARGE_FLAGS_DUAL_ROLE         (1 << 15)
  /* Port is the pending override port */
  #define CHARGE_FLAGS_DELAYED_OVERRIDE  (1 << 14)
  /* Port is the override port */
  #define CHARGE_FLAGS_OVERRIDE          (1 << 13)
  /* Charger type */
  #define CHARGE_FLAGS_TYPE_SHIFT               3
  #define CHARGE_FLAGS_TYPE_MASK       (0xf << CHARGE_FLAGS_TYPE_SHIFT)
  /* Power delivery role */
  #define CHARGE_FLAGS_ROLE_MASK         (7 <<  0)

  
  /*

   * PD_EVENT_PS_FAULT data field flags definition :

   */

  #define PS_FAULT_OCP                          1
  #define PS_FAULT_FAST_OCP                     2
  #define PS_FAULT_OVP                          3
  #define PS_FAULT_DISCH                        4

  
  /*

   * PD_EVENT_VIDEO_CODEC payload is "struct mcdp_info".

   */

  struct __ec_align4 mcdp_version {
  	uint8_t major;
  	uint8_t minor;
  	uint16_t build;
  };

  struct __ec_align4 mcdp_info {
  	uint8_t family[2];
  	uint8_t chipid[2];
  	struct mcdp_version irom;
  	struct mcdp_version fw;
  };

  /* struct mcdp_info field decoding */
  #define MCDP_CHIPID(chipid) ((chipid[0] << 8) | chipid[1])
  #define MCDP_FAMILY(family) ((family[0] << 8) | family[1])

  /* Get/Set USB-PD Alternate mode info */
  #define EC_CMD_USB_PD_GET_AMODE 0x0116
  struct __ec_align_size1 ec_params_usb_pd_get_mode_request {
  	uint16_t svid_idx; /* SVID index to get */
  	uint8_t port;      /* port */

  };

  struct __ec_align4 ec_params_usb_pd_get_mode_response {
  	uint16_t svid;   /* SVID */
  	uint16_t opos;    /* Object Position */
  	uint32_t vdo[6]; /* Mode VDOs */
  };

  #define EC_CMD_USB_PD_SET_AMODE 0x0117

  enum pd_mode_cmd {
  	PD_EXIT_MODE = 0,
  	PD_ENTER_MODE = 1,
  	/* Not a command.  Do NOT remove. */
  	PD_MODE_CMD_COUNT,
  };

  struct __ec_align4 ec_params_usb_pd_set_mode_request {
  	uint32_t cmd;  /* enum pd_mode_cmd */
  	uint16_t svid; /* SVID to set */
  	uint8_t opos;  /* Object Position */
  	uint8_t port;  /* port */
  };

  /* Ask the PD MCU to record a log of a requested type */
  #define EC_CMD_PD_WRITE_LOG_ENTRY 0x0118

  struct __ec_align1 ec_params_pd_write_log_entry {
  	uint8_t type; /* event type : see PD_EVENT_xx above */
  	uint8_t port; /* port#, or 0 for events unrelated to a given port */
  };

  /* Control USB-PD chip */
  #define EC_CMD_PD_CONTROL 0x0119

  enum ec_pd_control_cmd {
  	PD_SUSPEND = 0,      /* Suspend the PD chip (EC: stop talking to PD) */
  	PD_RESUME,           /* Resume the PD chip (EC: start talking to PD) */
  	PD_RESET,            /* Force reset the PD chip */
  	PD_CONTROL_DISABLE   /* Disable further calls to this command */
  };

  struct __ec_align1 ec_params_pd_control {
  	uint8_t chip;         /* chip id (should be 0) */
  	uint8_t subcmd;
  };

  /* Get info about USB-C SS muxes */
  #define EC_CMD_USB_PD_MUX_INFO 0x011A

  struct __ec_align1 ec_params_usb_pd_mux_info {
  	uint8_t port; /* USB-C port number */
  };

  /* Flags representing mux state */
  #define USB_PD_MUX_USB_ENABLED       (1 << 0)
  #define USB_PD_MUX_DP_ENABLED        (1 << 1)
  #define USB_PD_MUX_POLARITY_INVERTED (1 << 2)
  #define USB_PD_MUX_HPD_IRQ           (1 << 3)

  struct __ec_align1 ec_response_usb_pd_mux_info {
  	uint8_t flags; /* USB_PD_MUX_*-encoded USB mux state */
  };

  #define EC_CMD_PD_CHIP_INFO		0x011B

  struct __ec_align1 ec_params_pd_chip_info {
  	uint8_t port;	/* USB-C port number */
  	uint8_t renew;	/* Force renewal */
  };

  struct __ec_align2 ec_response_pd_chip_info {
  	uint16_t vendor_id;
  	uint16_t product_id;
  	uint16_t device_id;
  	union {
  		uint8_t fw_version_string[8];
  		uint64_t fw_version_number;
  	};
  };

  /* Run RW signature verification and get status */
  #define EC_CMD_RWSIG_CHECK_STATUS	0x011C
  
  struct __ec_align4 ec_response_rwsig_check_status {
  	uint32_t status;
  };

  /* For controlling RWSIG task */
  #define EC_CMD_RWSIG_ACTION	0x011D

  enum rwsig_action {
  	RWSIG_ACTION_ABORT = 0,		/* Abort RWSIG and prevent jumping */
  	RWSIG_ACTION_CONTINUE = 1,	/* Jump to RW immediately */
  };
  
  struct __ec_align4 ec_params_rwsig_action {
  	uint32_t action;
  };
  
  /* Run verification on a slot */
  #define EC_CMD_EFS_VERIFY	0x011E
  
  struct __ec_align1 ec_params_efs_verify {
  	uint8_t region;		/* enum ec_flash_region */
  };

  
  /*

   * Retrieve info from Cros Board Info store. Response is based on the data
   * type. Integers return a uint32. Strings return a string, using the response
   * size to determine how big it is.
   */
  #define EC_CMD_GET_CROS_BOARD_INFO	0x011F
  /*
   * Write info into Cros Board Info on EEPROM. Write fails if the board has
   * hardware write-protect enabled.

   */

  #define EC_CMD_SET_CROS_BOARD_INFO	0x0120
  
  enum cbi_data_tag {
  	CBI_TAG_BOARD_VERSION = 0, /* uint16_t or uint8_t[] = {minor,major} */
  	CBI_TAG_OEM_ID = 1,        /* uint8_t */
  	CBI_TAG_SKU_ID = 2,        /* uint8_t */
  	CBI_TAG_COUNT,
  };

  
  /*

   * Flags to control read operation
   *
   * RELOAD:  Invalidate cache and read data from EEPROM. Useful to verify
   *          write was successful without reboot.

   */

  #define CBI_GET_RELOAD		(1 << 0)

  struct __ec_align4 ec_params_get_cbi {
  	uint32_t type;		/* enum cbi_data_tag */
  	uint32_t flag;		/* CBI_GET_* */
  };

  
  /*

   * Flags to control write behavior.
   *
   * NO_SYNC: Makes EC update data in RAM but skip writing to EEPROM. It's
   *          useful when writing multiple fields in a row.
   * INIT:    Needs to be set when creating a new CBI from scratch. All fields
   *          will be initialized to zero first.

   */

  #define CBI_SET_NO_SYNC		(1 << 0)
  #define CBI_SET_INIT		(1 << 1)
  
  struct __ec_align1 ec_params_set_cbi {
  	uint32_t tag;		/* enum cbi_data_tag */
  	uint32_t flag;		/* CBI_SET_* */
  	uint32_t size;		/* Data size */
  	uint8_t data[];		/* For string and raw data */
  };

  /*****************************************************************************/
  /* The command range 0x200-0x2FF is reserved for Rotor. */

  
  /*****************************************************************************/

  /*
   * Reserve a range of host commands for the CR51 firmware.
   */
  #define EC_CMD_CR51_BASE 0x0300
  #define EC_CMD_CR51_LAST 0x03FF

  /*****************************************************************************/
  /* Fingerprint MCU commands: range 0x0400-0x040x */

  /* Fingerprint SPI sensor passthru command: prototyping ONLY */
  #define EC_CMD_FP_PASSTHRU 0x0400

  #define EC_FP_FLAG_NOT_COMPLETE 0x1

  struct __ec_align2 ec_params_fp_passthru {
  	uint16_t len;		/* Number of bytes to write then read */
  	uint16_t flags;		/* EC_FP_FLAG_xxx */
  	uint8_t data[];		/* Data to send */
  };

  /* Fingerprint sensor configuration command: prototyping ONLY */
  #define EC_CMD_FP_SENSOR_CONFIG 0x0401

  #define EC_FP_SENSOR_CONFIG_MAX_REGS 16

  struct __ec_align2 ec_params_fp_sensor_config {
  	uint8_t count;		/* Number of setup registers */
  	/*
  	 * the value to send to each of the 'count' setup registers
  	 * is stored in the 'data' array for 'len' bytes just after
  	 * the previous one.
  	 */
  	uint8_t len[EC_FP_SENSOR_CONFIG_MAX_REGS];
  	uint8_t data[];
  };

  /* Configure the Fingerprint MCU behavior */
  #define EC_CMD_FP_MODE 0x0402
  
  /* Put the sensor in its lowest power mode */
  #define FP_MODE_DEEPSLEEP     (1<<0)
  /* Wait to see a finger on the sensor */
  #define FP_MODE_FINGER_DOWN   (1<<1)
  /* Poll until the finger has left the sensor */
  #define FP_MODE_FINGER_UP     (1<<2)
  /* Capture the current finger image */
  #define FP_MODE_CAPTURE       (1<<3)
  /* special value: don't change anything just read back current mode */
  #define FP_MODE_DONT_CHANGE   (1<<31)
  
  struct __ec_align4 ec_params_fp_mode {
  	uint32_t mode; /* as defined by FP_MODE_ constants */
  	/* TBD */
  };

  struct __ec_align4 ec_response_fp_mode {
  	uint32_t mode; /* as defined by FP_MODE_ constants */
  	/* TBD */
  };

  /* Retrieve Fingerprint sensor information */
  #define EC_CMD_FP_INFO 0x0403
  
  struct __ec_align2 ec_response_fp_info {
  	/* Sensor identification */
  	uint32_t vendor_id;
  	uint32_t product_id;
  	uint32_t model_id;
  	uint32_t version;
  	/* Image frame characteristics */
  	uint32_t frame_size;
  	uint32_t pixel_format; /* using V4L2_PIX_FMT_ */
  	uint16_t width;
  	uint16_t height;
  	uint16_t bpp;
  };
  
  /* Get the last captured finger frame: TODO: will be AES-encrypted */
  #define EC_CMD_FP_FRAME 0x0404
  
  struct __ec_align4 ec_params_fp_frame {
  	uint32_t offset;
  	uint32_t size;
  };

  /*****************************************************************************/

  /* Touchpad MCU commands: range 0x0500-0x05FF */

  /* Perform touchpad self test */
  #define EC_CMD_TP_SELF_TEST 0x0500

  /* Get number of frame types, and the size of each type */
  #define EC_CMD_TP_FRAME_INFO 0x0501
  
  struct __ec_align4 ec_response_tp_frame_info {
  	uint32_t n_frames;
  	uint32_t frame_sizes[0];

  };

  /* Create a snapshot of current frame readings */
  #define EC_CMD_TP_FRAME_SNAPSHOT 0x0502

  /* Read the frame */
  #define EC_CMD_TP_FRAME_GET 0x0503

  struct __ec_align4 ec_params_tp_frame_get {
  	uint32_t frame_index;
  	uint32_t offset;
  	uint32_t size;
  };

  
  /*****************************************************************************/
  /*

   * Reserve a range of host commands for board-specific, experimental, or
   * special purpose features. These can be (re)used without updating this file.

   *

   * CAUTION: Don't go nuts with this. Shipping products should document ALL
   * their EC commands for easier development, testing, debugging, and support.

   *

   * All commands MUST be #defined to be 4-digit UPPER CASE hex values
   * (e.g., 0x00AB, not 0xab) for CONFIG_HOSTCMD_SECTION_SORTED to work.

   *

   * In your experimental code, you may want to do something like this:

   *

   *   #define EC_CMD_MAGIC_FOO 0x0000
   *   #define EC_CMD_MAGIC_BAR 0x0001
   *   #define EC_CMD_MAGIC_HEY 0x0002

   *

   *   DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_FOO, magic_foo_handler,
   *      EC_VER_MASK(0);

   *

   *   DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_BAR, magic_bar_handler,
   *      EC_VER_MASK(0);

   *

   *   DECLARE_PRIVATE_HOST_COMMAND(EC_CMD_MAGIC_HEY, magic_hey_handler,
   *      EC_VER_MASK(0);

   */

  #define EC_CMD_BOARD_SPECIFIC_BASE 0x3E00
  #define EC_CMD_BOARD_SPECIFIC_LAST 0x3FFF

  /*

   * Given the private host command offset, calculate the true private host
   * command value.

   */

  #define EC_PRIVATE_HOST_COMMAND_VALUE(command) \
  	(EC_CMD_BOARD_SPECIFIC_BASE + (command))

  
  /*****************************************************************************/
  /*

   * Passthru commands

   *

   * Some platforms have sub-processors chained to each other.  For example.

   *

   *     AP <--> EC <--> PD MCU

   *

   * The top 2 bits of the command number are used to indicate which device the
   * command is intended for.  Device 0 is always the device receiving the
   * command; other device mapping is board-specific.

   *

   * When a device receives a command to be passed to a sub-processor, it passes
   * it on with the device number set back to 0.  This allows the sub-processor
   * to remain blissfully unaware of whether the command originated on the next
   * device up the chain, or was passed through from the AP.
   *
   * In the above example, if the AP wants to send command 0x0002 to the PD MCU,
   *     AP sends command 0x4002 to the EC
   *     EC sends command 0x0002 to the PD MCU
   *     EC forwards PD MCU response back to the AP

   */

  /* Offset and max command number for sub-device n */
  #define EC_CMD_PASSTHRU_OFFSET(n) (0x4000 * (n))
  #define EC_CMD_PASSTHRU_MAX(n) (EC_CMD_PASSTHRU_OFFSET(n) + 0x3fff)
  
  /*****************************************************************************/

  /*

   * Deprecated constants. These constants have been renamed for clarity. The
   * meaning and size has not changed. Programs that use the old names should
   * switch to the new names soon, as the old names may not be carried forward
   * forever.

   */

  #define EC_HOST_PARAM_SIZE      EC_PROTO2_MAX_PARAM_SIZE
  #define EC_LPC_ADDR_OLD_PARAM   EC_HOST_CMD_REGION1
  #define EC_OLD_PARAM_SIZE       EC_HOST_CMD_REGION_SIZE

  #endif  /* !__ACPI__ && !__KERNEL__ */

  
  #endif  /* __CROS_EC_COMMANDS_H */