/*
   * Configuation settings for the esd TASREG board.
   *
   * (C) Copyright 2004
   * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
   *

   * SPDX-License-Identifier:	GPL-2.0+

   */
  
  /*
   * board/config.h - configuration options, board specific
   */
  
  #ifndef _M5249EVB_H
  #define _M5249EVB_H
  
  /*
   * High Level Configuration Options
   * (easy to change)
   */

  #define CONFIG_MCFTMR
  
  #define CONFIG_MCFUART

  #define CONFIG_SYS_UART_PORT		(0)

  
  #undef  CONFIG_WATCHDOG
  
  #undef CONFIG_MONITOR_IS_IN_RAM		/* no pre-loader required!!! ;-) */
  
  /*
   * BOOTP options
   */
  #undef CONFIG_BOOTP_BOOTFILESIZE

  
  /*
   * Command line configuration.
   */

  #define CONFIG_SYS_DEVICE_NULLDEV	1	/* include nulldev device	*/

  #define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands	*/

  #define CONFIG_SYS_LOAD_ADDR		0x200000	/* default load address */

  #define CONFIG_SYS_MEMTEST_START	0x400
  #define CONFIG_SYS_MEMTEST_END		0x380000

  /*
   * Clock configuration: enable only one of the following options
   */

  #undef  CONFIG_SYS_PLL_BYPASS				/* bypass PLL for test purpose */
  #define CONFIG_SYS_FAST_CLK		1		/* MCF5249 can run at 140MHz   */
  #define	CONFIG_SYS_CLK			132025600	/* MCF5249 can run at 140MHz   */

  
  /*
   * Low Level Configuration Settings
   * (address mappings, register initial values, etc.)
   * You should know what you are doing if you make changes here.
   */

  #define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
  #define	CONFIG_SYS_MBAR2		0x80000000

  
  /*-----------------------------------------------------------------------
   * Definitions for initial stack pointer and data area (in DPRAM)
   */

  #define CONFIG_SYS_INIT_RAM_ADDR	0x20000000

  #define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in internal SRAM	*/

  #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

  #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

  #define LDS_BOARD_TEXT \

  	. = DEFINED(env_offset) ? env_offset : .; \
  	env/embedded.o(.text);

  #define CONFIG_ENV_OFFSET		0x4000	/* Address of Environment Sector*/
  #define CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
  #define CONFIG_ENV_SECT_SIZE	0x2000 /* see README - env sector total size	*/

  
  /*-----------------------------------------------------------------------
   * Start addresses for the final memory configuration
   * (Set up by the startup code)

   * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0

   */

  #define CONFIG_SYS_SDRAM_BASE		0x00000000
  #define CONFIG_SYS_SDRAM_SIZE		16		/* SDRAM size in MB */

  #define CONFIG_SYS_FLASH_BASE		(CONFIG_SYS_CS0_BASE)

  
  #if 0 /* test-only */
  #define CONFIG_PRAM		512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
  #endif

  #define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)

  #define CONFIG_SYS_MONITOR_LEN		0x20000
  #define CONFIG_SYS_MALLOC_LEN		(1 * 1024*1024)	/* Reserve 1 MB for malloc()	*/
  #define CONFIG_SYS_BOOTPARAMS_LEN	64*1024

  
  /*
   * For booting Linux, the board info and command line data
   * have to be in the first 8 MB of memory, since this is
   * the maximum mapped by the Linux kernel during initialization ??
   */

  #define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))

  
  /*-----------------------------------------------------------------------
   * FLASH organization
   */

  #define CONFIG_SYS_FLASH_CFI
  #ifdef CONFIG_SYS_FLASH_CFI

  #	define CONFIG_FLASH_CFI_DRIVER	1

  #	define CONFIG_SYS_FLASH_SIZE		0x1000000	/* Max size that the board might have */
  #	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
  #	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
  #	define CONFIG_SYS_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
  #	define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
  #	define CONFIG_SYS_FLASH_CHECKSUM
  #	define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }

  #endif
  
  /*-----------------------------------------------------------------------
   * Cache Configuration
   */

  #define CONFIG_SYS_CACHELINE_SIZE	16

  #define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \

  					 CONFIG_SYS_INIT_RAM_SIZE - 8)

  #define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \

  					 CONFIG_SYS_INIT_RAM_SIZE - 4)

  #define CONFIG_SYS_ICACHE_INV		(CF_CACR_DCM)
  #define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_FLASH_BASE | \
  					 CF_ADDRMASK(2) | \
  					 CF_ACR_EN | CF_ACR_SM_ALL)
  #define CONFIG_SYS_CACHE_ACR1		(CONFIG_SYS_SDRAM_BASE | \
  					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
  					 CF_ACR_EN | CF_ACR_SM_ALL)
  #define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CEIB | \
  					 CF_CACR_DBWE)

  /*-----------------------------------------------------------------------
   * Memory bank definitions
   */
  
  /* CS0 - AMD Flash, address 0xffc00000 */

  #define	CONFIG_SYS_CS0_BASE		0xffe00000
  #define	CONFIG_SYS_CS0_CTRL		0x00001980	/* WS=0110, AA=1, PS=10         */

  /** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/

  #define	CONFIG_SYS_CS0_MASK		0x003f0021	/* 4MB, AA=0, WP=0, C/I=1, V=1  */

  
  /* CS1 - FPGA, address 0xe0000000 */

  #define	CONFIG_SYS_CS1_BASE		0xe0000000
  #define	CONFIG_SYS_CS1_CTRL		0x00000d80	/* WS=0011, AA=1, PS=10         */
  #define	CONFIG_SYS_CS1_MASK		0x00010001	/* 128kB, AA=0, WP=0, C/I=0, V=1*/

  
  /*-----------------------------------------------------------------------
   * Port configuration
   */

  #define	CONFIG_SYS_GPIO_FUNC		0x00000008	/* Set gpio pins: none          */
  #define	CONFIG_SYS_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54*/
  #define	CONFIG_SYS_GPIO_EN		0x00000008	/* Set gpio output enable       */
  #define	CONFIG_SYS_GPIO1_EN		0x00c70000	/* Set gpio output enable       */
  #define	CONFIG_SYS_GPIO_OUT		0x00000008	/* Set outputs to default state */
  #define	CONFIG_SYS_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
  #define CONFIG_SYS_GPIO1_LED		0x00400000	/* user led                     */

  
  #endif	/* M5249 */