/*
   * Copyright 2018 NXP
   *
   * SPDX-License-Identifier:	GPL-2.0+
   */
  
  #ifndef __IMX8MM_EVK_H
  #define __IMX8MM_EVK_H
  
  #include <linux/sizes.h>
  #include <asm/arch/imx-regs.h>
  
  #include "imx_env.h"
  
  #ifdef CONFIG_SECURE_BOOT
  #define CONFIG_CSF_SIZE			0x2000 /* 8K region */
  #endif
  
  #define CONFIG_SPL_MAX_SIZE		(148 * 1024)
  #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
  #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
  #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
  #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
  #define CONFIG_SYS_UBOOT_BASE		(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)
  
  #ifdef CONFIG_SPL_BUILD
  /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
  #define CONFIG_SPL_WATCHDOG_SUPPORT
  #define CONFIG_SPL_POWER_SUPPORT
  #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
  #define CONFIG_SPL_I2C_SUPPORT
  #define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
  #define CONFIG_SPL_STACK		0x91fff0
  #define CONFIG_SPL_LIBCOMMON_SUPPORT
  #define CONFIG_SPL_LIBGENERIC_SUPPORT
  #define CONFIG_SPL_SERIAL_SUPPORT
  #define CONFIG_SPL_GPIO_SUPPORT
  #define CONFIG_SPL_BSS_START_ADDR      0x00910000
  #define CONFIG_SPL_BSS_MAX_SIZE        0x2000	/* 8 KB */
  #define CONFIG_SYS_SPL_MALLOC_START    0x42200000
  #define CONFIG_SYS_SPL_MALLOC_SIZE     0x80000	/* 512 KB */
  #define CONFIG_SYS_ICACHE_OFF
  #define CONFIG_SYS_DCACHE_OFF
  
  #define CONFIG_MALLOC_F_ADDR		0x912000 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
  
  #define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */
  
  #undef CONFIG_DM_MMC
  #undef CONFIG_DM_PMIC
  #undef CONFIG_DM_PMIC_PFUZE100
  
  #define CONFIG_POWER
  #define CONFIG_POWER_I2C
  #define CONFIG_POWER_BD71837
  
  #define CONFIG_SYS_I2C
  #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
  #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
  #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
  
  #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
  
  #if defined(CONFIG_NAND_BOOT)
  #define CONFIG_SPL_NAND_SUPPORT
  #define CONFIG_SPL_DMA_SUPPORT
  #define CONFIG_SPL_NAND_MXS
  #define CONFIG_SYS_NAND_U_BOOT_OFFS 	0x4000000 /* Put the FIT out of first 64MB boot area */
  
  /* Set a redundant offset in nand FIT mtdpart. The new uuu will burn full boot image (not only FIT part) to the mtdpart, so we check both two offsets */
  #define CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND \
  	(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8400)
  #endif
  
  #endif
  
  #define CONFIG_CMD_READ
  #define CONFIG_SERIAL_TAG
  #define CONFIG_FASTBOOT_USB_DEV 0
  
  #define CONFIG_REMAKE_ELF
  
  #define CONFIG_BOARD_EARLY_INIT_F
  #define CONFIG_BOARD_POSTCLK_INIT
  #define CONFIG_BOARD_LATE_INIT
  
  /* Flat Device Tree Definitions */
  #define CONFIG_OF_BOARD_SETUP
  
  #undef CONFIG_CMD_EXPORTENV
  #undef CONFIG_CMD_IMPORTENV
  #undef CONFIG_CMD_IMLS
  
  #undef CONFIG_CMD_CRC32
  #undef CONFIG_BOOTM_NETBSD
  
  /* ENET Config */
  /* ENET1 */
  #if defined(CONFIG_CMD_NET)
  #define CONFIG_CMD_PING
  #define CONFIG_CMD_DHCP
  #define CONFIG_CMD_MII
  #define CONFIG_MII
  #define CONFIG_ETHPRIME                 "FEC"
  
  #define CONFIG_FEC_MXC
  #define CONFIG_FEC_XCV_TYPE             RGMII
  #define CONFIG_FEC_MXC_PHYADDR          0
  #define FEC_QUIRK_ENET_MAC
  
  #define CONFIG_PHY_GIGE
  #define IMX_FEC_BASE			0x30BE0000
  
  #define CONFIG_PHYLIB
  #define CONFIG_PHY_ATHEROS
  #endif
  
  /*
   * Another approach is add the clocks for inmates into clks_init_on
   * in clk-imx8mm.c, then clk_ingore_unused could be removed.
   */
  #define JAILHOUSE_ENV \
  	"jh_clk= \0 " \
  	"jh_mmcboot=mw 0x303d0518 0xff; setenv fdt_file fsl-imx8mm-evk-root.dtb;" \
  		"setenv jh_clk clk_ignore_unused; " \
  			   "if run loadimage; then " \
  				   "run mmcboot; " \
  			   "else run jh_netboot; fi; \0" \
  	"jh_netboot=mw 0x303d0518 0xff; setenv fdt_file fsl-imx8mm-evk-root.dtb; setenv jh_clk clk_ignore_unused; run netboot; \0 "
  
  #ifdef CONFIG_NAND_BOOT
  #define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(nandboot),16m(nandfit),32m(nandkernel),16m(nanddtb),8m(nandtee),-(nandrootfs) "
  #endif
  
  #define CONFIG_MFG_ENV_SETTINGS \
  	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
  	"initrd_addr=0x43800000\0" \
  	"initrd_high=0xffffffffffffffff\0" \
  	"emmc_dev=1\0"\
  	"sd_dev=0\0" \
  
  /* Initial environment variables */
  #if defined(CONFIG_NAND_BOOT)
  #define CONFIG_EXTRA_ENV_SETTINGS \
  	CONFIG_MFG_ENV_SETTINGS \
  	"fdt_addr=0x43000000\0"			\
  	"fdt_high=0xffffffffffffffff\0" \
  	"mtdparts=" MFG_NAND_PARTITION "\0" \
  	"console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200\0" \
  	"bootargs=console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200 ubi.mtd=5 "  \
  		"root=ubi0:nandrootfs rootfstype=ubifs "		     \
  		MFG_NAND_PARTITION \
  		"\0" \
  	"bootcmd=nand read ${loadaddr} 0x5000000 0x2000000;"\
  		"nand read ${fdt_addr} 0x7000000 0x100000;"\
  		"booti ${loadaddr} - ${fdt_addr}"
  
  #else
  #define CONFIG_EXTRA_ENV_SETTINGS		\
  	CONFIG_MFG_ENV_SETTINGS \
  	JAILHOUSE_ENV \
  	"script=boot.scr\0" \
  	"image=Image\0" \
  	"console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200\0" \
  	"fdt_addr=0x43000000\0"			\
  	"fdt_high=0xffffffffffffffff\0"		\
  	"boot_fdt=try\0" \
  	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
  	"initrd_addr=0x43800000\0"		\
  	"initrd_high=0xffffffffffffffff\0" \
  	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
  	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
  	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
  	"mmcautodetect=yes\0" \
  	"mmcargs=setenv bootargs ${jh_clk} console=${console} root=${mmcroot}\0 " \
  	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
  	"bootscript=echo Running bootscript from mmc ...; " \
  		"source\0" \
  	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
  	"mmcboot=echo Booting from mmc ...; " \
  		"run mmcargs; " \
  		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
  			"if run loadfdt; then " \
  				"booti ${loadaddr} - ${fdt_addr}; " \
  			"else " \
  				"echo WARN: Cannot load the DT; " \
  			"fi; " \
  		"else " \
  			"echo wait for boot; " \
  		"fi;\0" \
  	"netargs=setenv bootargs ${jh_clk} console=${console} " \
  		"root=/dev/nfs " \
  		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
  	"netboot=echo Booting from net ...; " \
  		"run netargs;  " \
  		"if test ${ip_dyn} = yes; then " \
  			"setenv get_cmd dhcp; " \
  		"else " \
  			"setenv get_cmd tftp; " \
  		"fi; " \
  		"${get_cmd} ${loadaddr} ${image}; " \
  		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
  			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
  				"booti ${loadaddr} - ${fdt_addr}; " \
  			"else " \
  				"echo WARN: Cannot load the DT; " \
  			"fi; " \
  		"else " \
  			"booti; " \
  		"fi;\0"
  
  #define CONFIG_BOOTCOMMAND \
  	   "mmc dev ${mmcdev}; if mmc rescan; then " \
  		   "if run loadbootscript; then " \
  			   "run bootscript; " \
  		   "else " \
  			   "if run loadimage; then " \
  				   "run mmcboot; " \
  			   "else run netboot; " \
  			   "fi; " \
  		   "fi; " \
  	   "else booti ${loadaddr} - ${fdt_addr}; fi"
  #endif
  
  /* Link Definitions */
  #define CONFIG_LOADADDR			0x40480000
  
  #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
  
  #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
  #define CONFIG_SYS_INIT_RAM_SIZE        0x80000
  #define CONFIG_SYS_INIT_SP_OFFSET \
          (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
  #define CONFIG_SYS_INIT_SP_ADDR \
          (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
  
  #define CONFIG_ENV_OVERWRITE
  #if defined(CONFIG_ENV_IS_IN_MMC)
  #define CONFIG_ENV_OFFSET               (64 * SZ_64K)
  #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
  #define CONFIG_ENV_OFFSET		(4 * 1024 * 1024)
  #define CONFIG_ENV_SECT_SIZE		(64 * 1024)
  #define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
  #define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
  #define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
  #define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
  #elif defined(CONFIG_ENV_IS_IN_NAND)
  #define CONFIG_ENV_OFFSET       (60 << 20)
  #endif
  #define CONFIG_ENV_SIZE			0x1000
  #define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC2 */
  #define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */
  
  /* Size of malloc() pool */
  #define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2*1024) + (16*1024)) * 1024)
  
  #define CONFIG_SYS_SDRAM_BASE           0x40000000
  #define PHYS_SDRAM                      0x40000000
  #define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */
  #define CONFIG_NR_DRAM_BANKS		1
  
  #define CONFIG_SYS_MEMTEST_START    PHYS_SDRAM
  #define CONFIG_SYS_MEMTEST_END      (CONFIG_SYS_MEMTEST_START + (PHYS_SDRAM_SIZE >> 1))
  
  #define CONFIG_BAUDRATE			115200
  
  #define CONFIG_MXC_UART
  #define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
  
  /* Monitor Command Prompt */
  #undef CONFIG_SYS_PROMPT
  #define CONFIG_SYS_PROMPT		"u-boot=> "
  #define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
  #define CONFIG_SYS_CBSIZE              2048
  #define CONFIG_SYS_MAXARGS             64
  #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
  #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
  					sizeof(CONFIG_SYS_PROMPT) + 16)
  
  #define CONFIG_IMX_BOOTAUX
  
  /* USDHC */
  #define CONFIG_CMD_MMC
  #define CONFIG_FSL_ESDHC
  #define CONFIG_FSL_USDHC
  
  #ifdef CONFIG_TARGET_IMX8MM_DDR4_EVK
  #define CONFIG_SYS_FSL_USDHC_NUM	1
  #else
  #define CONFIG_SYS_FSL_USDHC_NUM	2
  #endif
  #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  
  #define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
  #define CONFIG_SYS_MMC_IMG_LOAD_PART	1
  
  #ifdef CONFIG_FSL_FSPI
  #define CONFIG_SF_DEFAULT_BUS		0
  #define CONFIG_SF_DEFAULT_CS		0
  #define CONFIG_SF_DEFAULT_SPEED	40000000
  #define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
  #define FSL_FSPI_FLASH_SIZE		SZ_32M
  #define FSL_FSPI_FLASH_NUM		1
  #define FSPI0_BASE_ADDR			0x30bb0000
  #define FSPI0_AMBA_BASE			0x0
  #define	CONFIG_SPI_FLASH_BAR
  #define CONFIG_FSPI_QUAD_SUPPORT
  
  #define CONFIG_SYS_FSL_FSPI_AHB
  #endif
  
  /* Enable SPI */
  #ifndef CONFIG_NAND_MXS
  #ifndef CONFIG_FSL_FSPI
  #ifdef CONFIG_CMD_SF
  #define CONFIG_SPI_FLASH
  #define CONFIG_SPI_FLASH_STMICRO
  #define CONFIG_MXC_SPI
  #define CONFIG_SF_DEFAULT_BUS  0
  #define CONFIG_SF_DEFAULT_SPEED 20000000
  #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
  #endif
  #endif
  #endif
  
  #ifdef CONFIG_CMD_NAND
  #define CONFIG_NAND_MXS
  #define CONFIG_CMD_NAND_TRIMFFS
  
  /* NAND stuff */
  #define CONFIG_SYS_MAX_NAND_DEVICE     1
  #define CONFIG_SYS_NAND_BASE           0x20000000
  #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  #define CONFIG_SYS_NAND_ONFI_DETECTION
  
  /* DMA stuff, needed for GPMI/MXS NAND support */
  #define CONFIG_APBH_DMA
  #define CONFIG_APBH_DMA_BURST
  #define CONFIG_APBH_DMA_BURST8
  
  #ifdef CONFIG_CMD_UBI
  #define CONFIG_MTD_PARTITIONS
  #define CONFIG_MTD_DEVICE
  #endif
  #endif /* CONFIG_CMD_NAND */
  
  
  #define CONFIG_MXC_GPIO
  
  #define CONFIG_MXC_OCOTP
  #define CONFIG_CMD_FUSE
  
  #ifndef CONFIG_DM_I2C
  #define CONFIG_SYS_I2C
  #endif
  #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
  #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
  #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
  #define CONFIG_SYS_I2C_SPEED		100000
  
  /* USB configs */
  #ifndef CONFIG_SPL_BUILD
  #define CONFIG_CMD_USB
  #define CONFIG_USB_STORAGE
  #define CONFIG_USBD_HS
  
  #define CONFIG_CMD_USB_MASS_STORAGE
  #define CONFIG_USB_GADGET_MASS_STORAGE
  #define CONFIG_USB_FUNCTION_MASS_STORAGE
  
  #endif
  
  #define CONFIG_USB_GADGET_DUALSPEED
  #define CONFIG_USB_GADGET_VBUS_DRAW 2
  
  #define CONFIG_CI_UDC
  
  #define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)
  #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
  
  #ifdef CONFIG_VIDEO
  #define CONFIG_VIDEO_MXS
  #define CONFIG_VIDEO_LOGO
  #define CONFIG_SPLASH_SCREEN
  #define CONFIG_SPLASH_SCREEN_ALIGN
  #define CONFIG_CMD_BMP
  #define CONFIG_BMP_16BPP
  #define CONFIG_VIDEO_BMP_RLE8
  #define CONFIG_VIDEO_BMP_LOGO
  #define CONFIG_IMX_VIDEO_SKIP
  #define CONFIG_RM67191
  #endif
  
  #define CONFIG_OF_SYSTEM_SETUP
  
  #if defined(CONFIG_ANDROID_SUPPORT)
  #include "imx8mm_evk_android.h"
  #endif
  #endif