Blame view
board/freescale/mpc8349itx/README
5.62 KB
7a78f148d mpc83xx: Add supp... |
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 |
Freescale MPC8349E-mITX and MPC8349E-mITX-GP Boards --------------------------------------------------- 1. Board Description The MPC8349E-mITX and MPC8349E-mITX-GP are reference boards featuring the Freescale MPC8349E processor in a Mini-ITX form factor. The MPC8349E-mITX-GP is an MPC8349E-mITX with the following differences: A) One 8MB on-board flash EEPROM chip, instead of two. B) No SATA controller C) No Compact Flash slot D) No Mini-PCI slot E) No Vitesse 7385 5-port Ethernet switch F) No 4-port USB Type-A interface 2. Board Switches and Jumpers |
53677ef18 Big white-space c... |
19 |
2.0 Descriptions for all of the board jumpers can be found in the User |
7a78f148d mpc83xx: Add supp... |
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 |
Guide. Of particular interest to U-Boot developers is jumper J22: Pos. Name Default Description ----------------------------------------------------------------------- A LGPL0 ON (0) HRCW source, bit 0 B LGPL1 ON (0) HRCW source, bit 1 C LGPL3 ON (0) HRCW source, bit 2 D LGPL5 OFF (1) PCI_SYNC_OUT frequency E BOOT1 ON (0) Flash EEPROM boot device F PCI_M66EN ON (0) PCI 66MHz enable G I2C-WP ON (0) I2C EEPROM write protection H F_WP OFF (1) Flash EEPROM write protection Jumper J22.E is only for the ITX, and it decides the configuration of the flash chips. If J22.E is ON (i.e. jumpered), then flash chip U4 is located at address FE000000 and flash chip U7 is at FE800000. If J22.E is OFF, then U7 is at FE000000 and U4 is at FE800000. For U-Boot development, J22.E can be used to switch back-and-forth between two U-Boot images. 3. Memory Map 3.1. The memory map should look pretty much like this: 0x0000_0000 - 0x0FFF_FFFF DDR SDRAM (256 MB) 0x8000_0000 - 0x9FFF_FFFF PCI1 memory space (512 MB) 0xA000_0000 - 0xBFFF_FFFF PCI2 memory space (512 MB) 0xE000_0000 - 0xEFFF_FFFF IMMR (1 MB) 0xE200_0000 - 0xE2FF_FFFF PCI1 I/O space (16 MB) 0xE300_0000 - 0xE3FF_FFFF PCI2 I/O space (16 MB) 0xF000_0000 - 0xF000_FFFF Compact Flash (ITX only) 0xF001_0000 - 0xF001_FFFF Local bus expansion slot 0xF800_0000 - 0xF801_FFFF Vitesse 7385 Parallel Interface (ITX only) 0xFE00_0000 - 0xFE7F_FFFF First 8MB bank of Flash memory 0xFE80_0000 - 0xFEFF_FFFF Second 8MB bank of Flash memory (ITX only) 3.2 Flash EEPROM layout. On the ITX, jumper J22.E is used to determine which flash chips are at which address. When J22.E is switched, addresses from FE000000 to FE7FFFFF are swapped with addresses from FE800000 to FEFFFFFF. On the ITX, at the normal boot address (aka HIGHBOOT): FE00_0000 HRCW FE70_0000 Alternative U-Boot image FE80_0000 Alternative HRCW FEF0_0000 U-Boot image FEFF_FFFF End of flash On the ITX, at the low boot address (LOWBOOT) FE00_0000 HRCW and U-Boot image FE04_0000 U-Boot environment variables FE80_0000 Alternative HRCW and U-Boot image FEFF_FFFF End of flash On the ITX-GP, the only option is LOWBOOT and there is only one chip FE00_0000 HRCW and U-Boot image FE04_0000 U-Boot environment variables F7FF_FFFF End of flash 4. Definitions 4.1 Explanation of NEW definitions in: include/configs/MPC8349ITX.h |
0f8986049 83xx: Replace CON... |
89 |
CONFIG_MPC83xx MPC83xx family |
53677ef18 Big white-space c... |
90 |
CONFIG_MPC8349 MPC8349 specific |
7a78f148d mpc83xx: Add supp... |
91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 |
CONFIG_MPC8349ITX MPC8349E-mITX CONFIG_MPC8349ITXGP MPC8349E-mITX-GP 5. Compilation Assuming you're using BASH shell: export CROSS_COMPILE=your-cross-compile-prefix cd u-boot make distclean make MPC8349ITX_config or: make MPC8349ITXGP_config or: make MPC8349ITX_LOWBOOT_config make 6. Downloading and Flashing Images 6.1 Download via tftp: tftp $loadaddr <uboot> where "<uboot>" is the path and filename, on the TFTP server, of the U-Boot image. 6.1 Reflash U-Boot Image using U-Boot setenv uboot <uboot> run tftpflash where "<uboot>" is the path and filename, on the TFTP server, of the U-Boot image. 6.2 Using the HRCW to switch between two different U-Boot images on the ITX Because the ITX has 16MB of flash, it is possible to keep two U-Boot images in flash, and use the HRCW to specify which one is to be used when the board boots. This trick is especially effective with a hardware debugger that can override the HRCW, such as the BDI-2000. When the BMS bit in the HRCW is 0, the ITX will boot the U-Boot image at address FE000000. When the BMS bit is 1, the ITX will boot the image at address FEF00000. Therefore, just put a U-Boot image at both FE000000 and FEF00000 and change the BMS bit whenever you want to boot the other image. Step-by-step instructions: 1) Build an ITX image to be loaded at FEF00000 make distclean make MPC8349ITX_config make 2) Take the u-boot.bin image and flash it at FEF00000. tftp $loadaddr u-boot.bin protect off all erase FEF00000 +$filesize cp.b $loadaddr FEF00000 $filesize 3) Build an ITX image to be loaded at FE000000 make distclean make MPC8349ITX_LOWBOOT_config make 4) Take the u-boot.bin image and flash it at FE000000. tftp $loadaddr u-boot.bin protect off FE000000 +$filesize erase FE000000 +$filesize cp.b $loadaddr FE000000 $filesize The HRCW in flash is currently set to boot the image at FE000000. If you have a hardware debugger, configure it to set the HRCW to B460A000 04040000 if you want to boot the image at FEF00000, or set it to B060A000 04040000 if you want to boot the image at FE000000. To change the HRCW in flash to boot the image at FEF00000, use these U-Boot commands: cp.b FE000000 1000 10000 ; copy 1st flash sector to 1000 mw.b 1020 b4 8 ; modify BMS bit protect off FE000000 +10000 erase FE000000 +10000 cp.b 1000 FE000000 10000 7. Notes 1) The console baudrate for MPC8349EITX is 115200bps. |