Blame view
doc/README.mpc85xx
5.87 KB
d41ce506b
Initial Release, ...
|
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 |
External Debug Support
----------------------
Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some
restrictions on external debugging (JTAG). In particular, for the debugger to
be able to receive control after a single step or breakpoint:
- MSR[DE] must be set
- A valid opcode must be fetchable, through the MMU, from the debug
exception vector (IVPR + IVOR15).
To maximize the time during which this requirement is met, U-Boot sets MSR[DE]
immediately on entry and keeps it set. It also uses a temporary TLB to keep a
mapping to a valid opcode at the debug exception vector, even if we normally
don't support exception vectors being used that early, and that's not the area
where U-Boot currently executes from.
Note that there may still be some small windows where debugging will not work,
such as in between updating IVPR and IVOR15.
Config Switches:
----------------
Please refer README section "MPC85xx External Debug Support"
Major Config Switches during various boot Modes
----------------------------------------------
NOR boot
!defined(CONFIG_SYS_RAMBOOT) && !defined(CONFIG_SPL)
NOR boot Secure
!defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT)
RAMBOOT(SD, SPI & NAND boot)
defined(CONFIG_SYS_RAMBOOT)
RAMBOOT Secure (SD, SPI & NAND)
defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SECURE_BOOT)
NAND SPL BOOT
defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_NAND_SPL)
TLB Entries during u-boot execution
-----------------------------------
Note: Sequence number is in order of execution
A) defined(CONFIG_SYS_RAMBOOT) i.e. SD, SPI, NAND RAMBOOT & NAND_SPL boot
1) TLB entry to overcome e500 v1/v2 debug restriction
Location : Label "_start_e500"
TLB Entry : CONFIG_SYS_PPC_E500_DEBUG_TLB
EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_MONITOR_BASE
Properties : 256K, AS0, I, IPROT
2) TLB entry for working in AS1
Location : Label "create_init_ram_area"
TLB Entry : 15
EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_MONITOR_BASE
Properties : 1M, AS1, I, G, IPROT
3) TLB entry for the stack during AS1
Location : Lable "create_init_ram_area"
TLB Entry : 14
EPN -->RPN : CONFIG_SYS_INIT_RAM_ADDR --> CONFIG_SYS_INIT_RAM_ADDR
Properties : 16K, AS1, IPROT
4) TLB entry for CCSRBAR during AS1 execution
Location : cpu_init_early_f
TLB Entry : 13
EPN -->RPN : CONFIG_SYS_CCSRBAR --> CONFIG_SYS_CCSRBAR
Properties : 1M, AS1, I, G
5) Invalidate unproctected TLB Entries
Location : cpu_init_early_f
Invalidated: 13
6) Create TLB entries as per boards/freescale/<board>/tlb.c
Location : cpu_init_early_f --> init_tlbs()
Properties : ..., AS0, ...
Please note It can overwrites previous TLB Entries.
7) Disable TLB Entries of AS1
Location : cpu_init_f --> disable_tlb()
Disable : 15, 14
8) Update Flash's TLB entry
Location : Board_init_r
TLB entry : Search from TLB entries
EPN -->RPN : CONFIG_SYS_FLASH_BASE --> CONFIG_SYS_FLASH_BASE_PHYS
Properties : Board specific size, AS0, I, G, IPROT
B) !defined(CONFIG_SYS_RAMBOOT) i.e. NOR boot
1) TLB entry to overcome e500 v1/v2 debug restriction
Location : Label "_start_e500"
TLB Entry : CONFIG_SYS_PPC_E500_DEBUG_TLB
#if defined(CONFIG_SECURE_BOOT)
EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_PBI_FLASH_WINDOW
Properties : 1M, AS1, I, G, IPROT
#else
EPN -->RPN : CONFIG_SYS_MONITOR_BASE & 0xffc00000 --> 0xffc00000
Properties : 4M, AS0, I, G, IPROT
#endif
2) TLB entry for working in AS1
Location : Label "create_init_ram_area"
TLB Entry : 15
#if defined(CONFIG_SECURE_BOOT)
EPN -->RPN : CONFIG_SYS_MONITOR_BASE --> CONFIG_SYS_PBI_FLASH_WINDOW
Properties : 1M, AS1, I, G, IPROT
#else
EPN -->RPN : CONFIG_SYS_MONITOR_BASE & 0xffc00000 --> 0xffc00000
Properties : 4M, AS1, I, G, IPROT
#endif
3) TLB entry for the stack during AS1
Location : Lable "create_init_ram_area"
TLB Entry : 14
EPN -->RPN : CONFIG_SYS_INIT_RAM_ADDR --> CONFIG_SYS_INIT_RAM_ADDR
Properties : 16K, AS1, IPROT
4) TLB entry for CCSRBAR during AS1 execution
Location : cpu_init_early_f
TLB Entry : 13
EPN -->RPN : CONFIG_SYS_CCSRBAR --> CONFIG_SYS_CCSRBAR
Properties : 1M, AS1, I, G
5) TLB entry for Errata workaround CONFIG_SYS_FSL_ERRATUM_IFC_A003399
Location : cpu_init_early_f
TLB Entry : 9
EPN -->RPN : SRAM_BASE_ADDR --> SRAM_BASE_ADDR
Properties : 1M, AS1, I
6) CONFIG_SYS_FSL_ERRATUM_IFC_A003399 Adjust flash's phys addr
Location : cpu_init_early_f --> setup_ifc
TLB Entry : Get Flash TLB
EPN -->RPN : Adjusted flash_phys --> Adjusted flash_phys
Properties : 4M, AS1, I, G, IPROT
7) CONFIG_SYS_FSL_ERRATUM_IFC_A003399: E500 v1,v2 debug restriction
Location : cpu_init_early_f --> setup_ifc
TLB Entry : CONFIG_SYS_PPC_E500_DEBUG_TLB
EPN -->RPN : Adjusted flash_phys --> Adjusted flash_phys
Properties : 4M, AS0, I, G, IPROT
8) Invalidate unproctected TLB Entries
Location : cpu_init_early_f
Invalidated: 13, 9
9) Create TLB entries as per boards/freescale/<board>/tlb.c
Location : cpu_init_early_f --> init_tlbs()
Properties : ..., AS0, ...
Note: It can overwrites previous TLB Entries
10) Disable TLB Entries of AS1
Location : cpu_init_f --> disable_tlb()
Disable : 15, 14
11) Create DDR's TLB entriy
Location : Board_init_f -> dram_init
TLB entry : Search free TLB entry
12) Update Flash's TLB entry
Location : Board_init_r
TLB entry : Search from TLB entries
EPN -->RPN : CONFIG_SYS_FLASH_BASE --> CONFIG_SYS_FLASH_BASE_PHYS
Properties : Board specific size, AS0, I, G, IPROT
|