19 Mar, 2019
3 commits
-
This board uses Micron N25Q256A SPI flash. Enable SPI_FLASH_BAR to allow
us to access the whole chip.Signed-off-by: Chris Packham
Cc: Vignesh R
Signed-off-by: Stefan Roese -
Set CONFIG_SYS_MALLOC_F_LEN to match the rest of the mvebu boards. The
default of 0x400 is not enough when booting from SPI.Signed-off-by: Chris Packham
Signed-off-by: Stefan Roese -
Enable the mvpp2 network driver for the Armada 8K SoC.
Enable the Marvell PHY driver for the on-board 1512 PHY.
Signed-off-by: Baruch Siach
Reviewed-by: Stefan Roese
Signed-off-by: Stefan Roese
14 Mar, 2019
1 commit
13 Mar, 2019
11 commits
-
This patch supports enabling MTD, and the corresponding CMD_MTD
along with enabling the MXS NAND Controller with device tree
support.Signed-off-by: Adam Ford
-
Enable watchdog and bootcounter support on imx6qdl board
Signed-off-by: Shyam Saini
-
Currently the command "saveenv" is not available.
The CONFIG_ENV_IS_IN_MMC symbol has been converted to Kconfig,
so fix the problem by moving it to the defconfig.Signed-off-by: Fabio Estevam
Reviewed-by: Peng Fan -
Signed-off-by: Tim Harvey
-
There is no ethaddr assigned to each board, so we need to use random
value in order to use network.Signed-off-by: Marcin Niestroj
-
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove USB code that is on longer
executed after enabling CONFIG_DM_USB. Enable CONFIG_PINCTRL, so we
can get rid of ethernet pin configuration.Signed-off-by: Marcin Niestroj
-
Convert to use DM_PMIC for the PFUZE3000. Since this PMIC is
under an I2C bus, conver to DM_I2C as well.Also, since I2C is not used in SPL, remove CONFIG_SPL_I2C_SUPPORT
to avoid build warnings.Signed-off-by: Fabio Estevam
Acked-by: Otavio Salvador -
Convert to CONFIG_DM_GPIO.
Also, DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation, so do as requested.Signed-off-by: Fabio Estevam
Acked-by: Otavio Salvador -
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam
Acked-by: Otavio Salvador -
Select CONFIG_OF_CONTROL and the appropriate device tree files
in preparation for converting to driver model.Signed-off-by: Fabio Estevam
Acked-by: Otavio Salvador -
The Ethernet controller is not able to initialise correctly without the
pinctrl driver.This config setting was enabled in the initial version of this file,
but was removed by a savedefconfig resync because the parameter did not
actually exist at that point.Fixes: 1bac199e8c87 ("configs: Resync with savedefconfig")
Signed-off-by: Chris Spencer
Reviewed-by: Fabio Estevam
12 Mar, 2019
1 commit
-
This commit enables support for I2C S3C424X0 driver.
Signed-off-by: Anand Moon
Acked-by: Lukasz Majewski
Signed-off-by: Minkyu Kang
11 Mar, 2019
3 commits
-
- ACPI changes and fixes to Intel Tangier/Edison
- i8254 beeper fixes -
Use the i8254 sound driver to support creating simple beeps.
Signed-off-by: Bin Meng
Reviewed-by: Simon Glass -
Printing the "Type" of board requires proper detection of revision which
can happen only late because regulators are needed.Signed-off-by: Krzysztof Kozlowski
Tested-by: Anand Moon
Signed-off-by: Minkyu Kang
10 Mar, 2019
1 commit
-
Enable DM_SPI and DM_SPI_FLASH in U-Boot on H2 Stout, M2W Porter and E3 Silk.
Signed-off-by: Marek Vasut
Cc: Nobuhiro Iwamatsu
05 Mar, 2019
1 commit
-
First set of u-boot-atmel fixes for 2019.04 cycle
04 Mar, 2019
3 commits
-
SPL_GENERATE_ATMEL_PMECC_HEADER will generate a header for the SPL for NAND
information. The initial stage 1 bootloader will use this header in case the
NAND flash doesn't support commands to retrieve sector size, etc.
However this header is bad for different boot media, like MMC or SPI.
In case SD_BOOT or SPI_BOOT is used, remove the config for this.Signed-off-by: Eugen Hristev
-
This was already set for 'sama5d27_som1_ek_mmc_defconfig' (first SD
card, full size). Without this option set, the MAC address is not read
from the I²C EEPROM at boot, and remains unset:U-Boot 2019.01 (Jan 01 2019 - 00:00:00 +0000)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
DRAM: 128 MiB
MMC: sdio-host@a0000000: 0, sdio-host@b0000000: 1
Loading Environment from FAT... OK
In: serial
Out: serial
Err: serial
Net:
Error: ethernet@f8008000 address not set.
eth-1: ethernet@f8008000
Hit any key to stop autoboot: 0Signed-off-by: Alexander Dahl
-
Re-organize defconfig and enabled PPA for secure boot
Signed-off-by: Prabhakar Kushwaha
03 Mar, 2019
2 commits
-
EFI applications need bounce buffers to work properly on these
platforms.Signed-off-by: Mian Yousaf Kaukab
Reviewed-by: Prabhakar Kushwaha -
EFI applications need bounce buffers to work properly on these
platforms.Signed-off-by: Mian Yousaf Kaukab
Reviewed-by: Prabhakar Kushwaha
01 Mar, 2019
2 commits
-
- Gen2/Gen3 fixes for warnings and sdhi
-
- Various Bananapi fixes
27 Feb, 2019
1 commit
-
This patch adds SiFive FU540 board support. For now, only
SiFive serial, SiFive PRCI, and Cadance MACB drivers are
only enabled. The SiFive FU540 defconfig by default builds
U-Boot for S-Mode because U-Boot on SiFive FU540 will run
in S-Mode as payload of BBL or OpenSBI.Signed-off-by: Atish Patra
Signed-off-by: Anup Patel
Reviewed-by: Alexander Graf
Reviewed-by: Lukas Auer
Reviewed-by: Bin Meng
25 Feb, 2019
2 commits
-
Convert R-Car Gen2 from OF_EMBED to OF_SEPARATE, thus getting
rid of one of the deprecation warnings.Signed-off-by: Marek Vasut
Cc: Nobuhiro Iwamatsu -
Synchronize Gen3 defconfigs in wake of the Kconfig option changes.
Signed-off-by: Marek Vasut
Cc: Nobuhiro Iwamatsu
23 Feb, 2019
1 commit
-
This is the same migration path as commit b6251db8c3f0 ("Kconfig:
Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND").I also moved the description in README to the Kconfig help.
I ripped off the sentence about 'LWMON' since it is gone already.I only let my boards migrate, leaving the rest to platform maintainers.
Signed-off-by: Masahiro Yamada
22 Feb, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
21 Feb, 2019
6 commits
-
- Add support for sound.
Albeit the big changeset, changes are pretty limited to x86 only and a
few new sound drivers used by x86 so I think it would be good to have
this in the next release. -
- Support of NXP's LX2160RDB and LX2160QDS platform
- Enable SATA DM model for NXP's ARM SoCs -
Migrate TEGRA_KEYBOARD from headers to Kconfig, only the seaboard uses it but we
drop CONFIG_KEYBOARD as the driver doesn't use the legacy drv_keyboard_init.Signed-off-by: Peter Robinson
Cc: Tom Warren
Cc: Stephen Warren
Signed-off-by: Tom Warren -
Migrate USB_EHCI_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson
Cc: Tom Warren
Cc: Stephen Warren
Cc: Marek Vasut
Cc: Marcel Ziswiler
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach
Cc: Stefan Agner
Cc: Alban Bedel
Cc: Allen Martin
Signed-off-by: Tom Warren -
Migrate SYS_I2C_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson
Cc: Tom Warren
Cc: Stephen Warren
Cc: Heiko Schocher
Cc: Marcel Ziswiler
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach
Cc: Stefan Agner
Cc: Alban Bedel
Cc: Allen Martin
Signed-off-by: Tom Warren
20 Feb, 2019
1 commit
-
Enable sound on samus using the broadwell I2S and an RT5677 audio codec.
Reviewed-by: Bin Meng
Signed-off-by: Simon Glass
