06 May, 2015
3 commits
-
Signed-off-by: Tom Rini
-
Without this, when CONFIG_ENV_VARS_UBOOT_CONFIG is active we get
a compile time error when doing 'make env'.
In file included from tools/env/fw_env.c:117:0:
include/env_default.h:110:11: error: expected ‘}’ before ‘CONFIG_SYS_ARCH’When building U-Boot this is included indirectly by the compiler switch
-include
/home/trdx/git.toradex.com/u-boot-2014.10-toradex/include/linux/kconfig.hSigned-off-by: Max Krummenacher
Signed-off-by: Marcel Ziswiler
05 May, 2015
37 commits
-
By removing this default build target, the "u-boot.kwb" target is not
automatically generated. This fixes a temporary build error when using
out-of-tree builds, as buildman does per default (reported by Simon).When the full SPL support is added for these targets with the DDR training
code, the "u-boot-spl.kwb" image will be generated automatically.Users providing a special bin_hdr binary (binary.0) file can always add
this binary file and generate the full firmware image by issuing the
"make u-boot.kwb" command directly.Signed-off-by: Stefan Roese
Cc: Simon Glass
Cc: Prafulla Wadaskar
Cc: Luka Perkov -
The macro to select the I2C address for ECC bus-width detection
was defined incorrectly for the Marvell DB-MV784MP-GP board. This
patch changes the macro to the correct value to fix this issue.Signed-off-by: Stefan Roese
-
This patch adds support for the Marvell DB-88F6820-GP Armada A38x
evaluation board.Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)Please note that this board support right now only supports the
main U-Boot. Without the bin_hdr integration (DDR training etc). This
will be added in a few days / weeks to complete this board port. But
till then this U-Boot version can be run on the target via the
original Marvell U-Boot via this command:tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000
Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
This solves some RX problems that have been seen, when using the
mvneta ethernet driver. The cache needs to be reset into a "clean"
state before using it.Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
This enables the usage of the "preboot" environment variable on Marvell
boards.Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
We are not using the coherency feature in U-Boot at all. So lets remove
this configuration from the mbus driver.Signed-off-by: Stefan Roese
Cc: Thomas Petazzoni
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach
Acked-by: Joe Hershberger -
This patch adds support for the Marvell Armada 38x SoC family.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)Tested on Marvell DB-88F6820-GP evaluation board.
Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
This define is used by the DDR training code for Armada XP. With the
upcoming addition of Armada 38x support, lets only define it for
Armada XP in this common header.Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
MAX_MVNETA_DEVS is not used anywhere in U-Boot. So lets remove it.
Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
Since these files will be used for other MVEBU SoC's, lets reflect this
in the headers marcos as well.Signed-off-by: Stefan Roese
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.Signed-off-by: Stefan Roese
Cc: Masahiro Yamada
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
Move arch/arm/include/asm/arch-armada-xp/*
-> arch/arm/mach-mvebu/include/mach/*Additionally the SYS_SOC is renamed from "armada-xp" to "mvebu". With this
change all these files can better be shared with other, newer Mavell
MVEBU SoC's. Like the upcoming Armada 38x support.Signed-off-by: Stefan Roese
Cc: Masahiro Yamada
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
Move arch/arm/cpu/armv7armada-xp/* -> arch/arm/mach-mvebu/*
Since this platform will be extended to support other Marvell SoC's as
well, lets rename it directly to mvebu.This will be used by the upcoming Armada 38x suport (A38x).
Signed-off-by: Stefan Roese
Cc: Masahiro Yamada
Tested-by: Kevin Smith
Tested-by: Dirk Eibach -
The get_timer_us() function is something which is no longer
existing in case we use generic timer framework, so replace
it with get_timer().Signed-off-by: Marek Vasut
Cc: Stephen Warren
Cc: Tyler Baker -
If the mmc device is non-removable (as indicated by the device tree), set
the flag so that users of the device know.Signed-off-by: Simon Glass
Reviewed-by: Joe Hershberger -
We need to clear the allocated memory explicitly as the included
struct sdhci_host has function pointers. Those are compared to NULL to
test if this (optional) feature is supported. Leaving them undefined let
u-boot jump to arbitrary memory.Signed-off-by: Alexander Stein
-
Freescale eMMC44 adapter card uses Micron N2M400FDB311A3CF eMMC
memory. According to the silicon datasheet, secure erase timeout
is 600ms. So increase erase timeout value from 250ms to 600ms.Signed-off-by: Yangbo Lu
Cc: York Sun -
Timeout interrupt also work for response busy command(R1b) like
cmd38/cmd6. So need to set it accordingly. Current code only
set timeout for data command.Signed-off-by: Kevin Liu
Signed-off-by: Rob Herring
Cc: Pantelis Antoniou -
High capacity support is not a host capability, but a device capability
that is queried via the OCR. The flag in the operating conditions
request argument can just be set unconditionally. This matches the Linux
implementation.[panto] Hand merged and renumbering MMC_MODE_DDR_52MHz.
Signed-off-by: Rob Herring
Signed-off-by: Pantelis Antoniou
Cc: Pantelis Antoniou -
Starting part of device initialization sets the init_in_progress flag
only if the MMC card did not yet come to ready state and needs to continue
polling. If the card is SD or if the MMC card became ready quickly,
the flag is not set and (if using pre-initialization) the starting
phase will be re-executed from mmc_init function.Set the init_in_progress flag in all non-error cases. Also, move flags
setting statements around so that the flags are not set in error paths.
Also, IN_PROGRESS return status becomes unnecessary, so get rid of it.Signed-off-by: Andrew Gabbasov
-
The polling loops in sd_send_op_cond and mmc_complete_op_cond functions
check the ready flag state at the end of the loop, that is after executing
a delay inside the loop, which, in case of exiting with no error,
is not needed. Also, one of these loops, as well as the loop
in mmc_send_status, have the delay just before exiting on timeout
conditions.Restructure all these loops to check the respective conditions before making
a delay for the next loop pass, and to appropriately exit without the delay.Signed-off-by: Andrew Gabbasov
-
Some MMC cards come to ready state quite quickly, so that the respective
flag appears to be set in mmc_send_op_cond already. In this case trying
to continue polling the card with CMD1 in mmc_complete_op_cond is incorrect
and may lead to unpredictable results. So check the flag before polling
and skip it appropriately.Signed-off-by: Andrew Gabbasov
-
The previous change to use 'ocr' structure field for storing send_op_cond
command response also stopped using command response directly
outside of mmc_send_op_cond_iter(). Now it becomes possible to use
command structure in mmc_send_op_cond_iter() locally, removing a necessity
to pass it as an argument from the caller.Signed-off-by: Andrew Gabbasov
-
The 'op_cond_response' field in mmc structure contains the response
from the last SEND_OP_COND MMC command while making iterational
polling of the card. Later it is copied to 'ocr' field, designed
to contain the OCR register value, which is actually the same
response from the same command. So, these fields have actually
the same data, just in different time periods. It's easier to use
the same 'ocr' field in both cases at once, without temporary using
of the 'op_cond_response' field.Signed-off-by: Andrew Gabbasov
-
The version flag constant name used in IS_MMC macro is incorrect/undefined.
Signed-off-by: Andrew Gabbasov
-
New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/Signed-off-by: Michael Durrant
Signed-off-by: Oleksandr G Zhadan
[York Sun: remove patman tags from commit message]
Reviewed-by: York Sun -
To replicate:
1. add to include/configs/p1_p2_rdb_pc.h "#define CONFIG_CMD_GPIO"
2. run `make P1020RDB-PC_defconfig`
3. run CROSS_COMPILE=powerpc-linux- makeand you will get:
common/built-in.o: In function `do_gpio':
u-boot/common/cmd_gpio.c:186: undefined reference to `gpio_request'
u-boot/common/cmd_gpio.c:194: undefined reference to `gpio_direction_input'
u-boot/common/cmd_gpio.c:195: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:200: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:203: undefined reference to `gpio_direction_output'
u-boot/common/cmd_gpio.c:209: undefined reference to `gpio_freeSigned-off-by: Michael Durrant
Signed-off-by: Oleksandr G Zhadan
Reviewed-by: York Sun -
1. board/freescale/t4qds/t4_rcw.cfg
1.8GHz support is requested as default frequency, so update the rcw.2. remove un-used configs
configs/T4160QDS_SPIFLASH_defconfig
configs/T4240QDS_SPIFLASH_defconfig
SPI boot is not available on T4QDS, so the configs should be removed.3. board/freescale/t4qds/MAINTAINERS
Updated MAINTAINERS accordingly.Signed-off-by: Shaohui Xie
[York Sun: revise subject]
Reviewed-by: York Sun -
T2080RDB RevC uses new SODIMM 1867MT/s instead of previous 1600MT/s.
So update RCW to support new DDR frequency 1867MT/s by default.
Reserve the old 1600MT/s in comment for users in needed.Signed-off-by: Shengzhou Liu
Reviewed-by: York Sun -
Enable eSDHC peripheral clock support. u-boot and linux will
use SD clock generated by peripheral clock instead of platform
clock.Signed-off-by: Yangbo Lu
Cc: York Sun
Cc: Pantelis Antoniou
Reviewed-by: York Sun
