PCI Error Recovery
                         ------------------

                          February 2, 2006
  
                   Current document maintainer:
               Linas Vepstas <linas@austin.ibm.com>
  
  
  Many PCI bus controllers are able to detect a variety of hardware
  PCI errors on the bus, such as parity errors on the data and address
  busses, as well as SERR and PERR errors.  Some of the more advanced
  chipsets are able to deal with these errors; these include PCI-E chipsets,
  and the PCI-host bridges found on IBM Power4 and Power5-based pSeries
  boxes. A typical action taken is to disconnect the affected device,
  halting all I/O to it.  The goal of a disconnection is to avoid system
  corruption; for example, to halt system memory corruption due to DMA's
  to "wild" addresses. Typically, a reconnection mechanism is also
  offered, so that the affected PCI device(s) are reset and put back
  into working condition. The reset phase requires coordination
  between the affected device drivers and the PCI controller chip.
  This document describes a generic API for notifying device drivers
  of a bus disconnection, and then performing error recovery.
  This API is currently implemented in the 2.6.16 and later kernels.
  
  Reporting and recovery is performed in several steps. First, when
  a PCI hardware error has resulted in a bus disconnect, that event
  is reported as soon as possible to all affected device drivers,
  including multiple instances of a device driver on multi-function
  cards. This allows device drivers to avoid deadlocking in spinloops,
  waiting for some i/o-space register to change, when it never will.
  It also gives the drivers a chance to defer incoming I/O as
  needed.
  
  Next, recovery is performed in several stages. Most of the complexity
  is forced by the need to handle multi-function devices, that is,
  devices that have multiple device drivers associated with them.
  In the first stage, each driver is allowed to indicate what type
  of reset it desires, the choices being a simple re-enabling of I/O
  or requesting a hard reset (a full electrical #RST of the PCI card).
  If any driver requests a full reset, that is what will be done.
  
  After a full reset and/or a re-enabling of I/O, all drivers are
  again notified, so that they may then perform any device setup/config
  that may be required.  After these have all completed, a final
  "resume normal operations" event is sent out.
  
  The biggest reason for choosing a kernel-based implementation rather
  than a user-space implementation was the need to deal with bus
  disconnects of PCI devices attached to storage media, and, in particular,
  disconnects from devices holding the root file system.  If the root
  file system is disconnected, a user-space mechanism would have to go
  through a large number of contortions to complete recovery. Almost all
  of the current Linux file systems are not tolerant of disconnection
  from/reconnection to their underlying block device. By contrast,
  bus errors are easy to manage in the device driver. Indeed, most
  device drivers already handle very similar recovery procedures;
  for example, the SCSI-generic layer already provides significant
  mechanisms for dealing with SCSI bus errors and SCSI bus resets.
  
  
  Detailed Design
  ---------------
  Design and implementation details below, based on a chain of
  public email discussions with Ben Herrenschmidt, circa 5 April 2005.

  
  The error recovery API support is exposed to the driver in the form of
  a structure of function pointers pointed to by a new field in struct

  pci_driver. A driver that fails to provide the structure is "non-aware",
  and the actual recovery steps taken are platform dependent.  The
  arch/powerpc implementation will simulate a PCI hotplug remove/add.

  
  This structure has the form:

  struct pci_error_handlers
  {

  	int (*error_detected)(struct pci_dev *dev, enum pci_channel_state);

  	int (*mmio_enabled)(struct pci_dev *dev);

  	int (*link_reset)(struct pci_dev *dev);
  	int (*slot_reset)(struct pci_dev *dev);

  	void (*resume)(struct pci_dev *dev);

  };

  The possible channel states are:
  enum pci_channel_state {
  	pci_channel_io_normal,  /* I/O channel is in normal state */
  	pci_channel_io_frozen,  /* I/O to channel is blocked */
  	pci_channel_io_perm_failure, /* PCI card is dead */
  };
  
  Possible return values are:
  enum pci_ers_result {
  	PCI_ERS_RESULT_NONE,        /* no result/none/not supported in device driver */
  	PCI_ERS_RESULT_CAN_RECOVER, /* Device driver can recover without slot reset */
  	PCI_ERS_RESULT_NEED_RESET,  /* Device driver wants slot to be reset. */
  	PCI_ERS_RESULT_DISCONNECT,  /* Device has completely failed, is unrecoverable */
  	PCI_ERS_RESULT_RECOVERED,   /* Device driver is fully recovered and operational */
  };
  
  A driver does not have to implement all of these callbacks; however,
  if it implements any, it must implement error_detected(). If a callback
  is not implemented, the corresponding feature is considered unsupported.
  For example, if mmio_enabled() and resume() aren't there, then it
  is assumed that the driver is not doing any direct recovery and requires

  a reset. If link_reset() is not implemented, the card is assumed as

  not care about link resets. Typically a driver will want to know about
  a slot_reset().
  
  The actual steps taken by a platform to recover from a PCI error
  event will be platform-dependent, but will follow the general
  sequence described below.
  
  STEP 0: Error Event
  -------------------
  PCI bus error is detect by the PCI hardware.  On powerpc, the slot
  is isolated, in that all I/O is blocked: all reads return 0xffffffff,
  all writes are ignored.
  
  
  STEP 1: Notification
  --------------------
  Platform calls the error_detected() callback on every instance of
  every driver affected by the error.
  
  At this point, the device might not be accessible anymore, depending on
  the platform (the slot will be isolated on powerpc). The driver may
  already have "noticed" the error because of a failing I/O, but this
  is the proper "synchronization point", that is, it gives the driver
  a chance to cleanup, waiting for pending stuff (timers, whatever, etc...)
  to complete; it can take semaphores, schedule, etc... everything but
  touch the device. Within this function and after it returns, the driver

  shouldn't do any new IOs. Called in task context. This is sort of a
  "quiesce" point. See note about interrupts at the end of this doc.

  All drivers participating in this system must implement this call.
  The driver must return one of the following result codes:
  		- PCI_ERS_RESULT_CAN_RECOVER:
  		  Driver returns this if it thinks it might be able to recover

  		  the HW by just banging IOs or if it wants to be given

  		  a chance to extract some diagnostic information (see
  		  mmio_enable, below).
  		- PCI_ERS_RESULT_NEED_RESET:
  		  Driver returns this if it can't recover without a hard
  		  slot reset.
  		- PCI_ERS_RESULT_DISCONNECT:
  		  Driver returns this if it doesn't want to recover at all.
  
  The next step taken will depend on the result codes returned by the
  drivers.
  
  If all drivers on the segment/slot return PCI_ERS_RESULT_CAN_RECOVER,
  then the platform should re-enable IOs on the slot (or do nothing in
  particular, if the platform doesn't isolate slots), and recovery
  proceeds to STEP 2 (MMIO Enable).
  
  If any driver requested a slot reset (by returning PCI_ERS_RESULT_NEED_RESET),
  then recovery proceeds to STEP 4 (Slot Reset).
  
  If the platform is unable to recover the slot, the next step
  is STEP 6 (Permanent Failure).
  
  >>> The current powerpc implementation assumes that a device driver will
  >>> *not* schedule or semaphore in this routine; the current powerpc

  >>> implementation uses one kernel thread to notify all devices;

  >>> thus, if one device sleeps/schedules, all devices are affected.

  >>> Doing better requires complex multi-threaded logic in the error
  >>> recovery implementation (e.g. waiting for all notification threads
  >>> to "join" before proceeding with recovery.)  This seems excessively
  >>> complex and not worth implementing.

  >>> The current powerpc implementation doesn't much care if the device
  >>> attempts I/O at this point, or not.  I/O's will fail, returning

  >>> a value of 0xff on read, and writes will be dropped. If the device
  >>> driver attempts more than 10K I/O's to a frozen adapter, it will
  >>> assume that the device driver has gone into an infinite loop, and

  >>> it will panic the kernel. There doesn't seem to be any other

  >>> way of stopping a device driver that insists on spinning on I/O.

  STEP 2: MMIO Enabled
  -------------------
  The platform re-enables MMIO to the device (but typically not the
  DMA), and then calls the mmio_enabled() callback on all affected
  device drivers.

  This is the "early recovery" call. IOs are allowed again, but DMA is

  not (hrm... to be discussed, I prefer not), with some restrictions. This
  is NOT a callback for the driver to start operations again, only to
  peek/poke at the device, extract diagnostic information, if any, and
  eventually do things like trigger a device local reset or some such,

  but not restart operations. This is callback is made if all drivers on
  a segment agree that they can try to recover and if no automatic link reset
  was performed by the HW. If the platform can't just re-enable IOs without
  a slot reset or a link reset, it wont call this callback, and instead
  will have gone directly to STEP 3 (Link Reset) or STEP 4 (Slot Reset)
  
  >>> The following is proposed; no platform implements this yet:
  >>> Proposal: All I/O's should be done _synchronously_ from within
  >>> this callback, errors triggered by them will be returned via
  >>> the normal pci_check_whatever() API, no new error_detected()
  >>> callback will be issued due to an error happening here. However,
  >>> such an error might cause IOs to be re-blocked for the whole
  >>> segment, and thus invalidate the recovery that other devices
  >>> on the same segment might have done, forcing the whole segment
  >>> into one of the next states, that is, link reset or slot reset.
  
  The driver should return one of the following result codes:
  		- PCI_ERS_RESULT_RECOVERED

  		  Driver returns this if it thinks the device is fully

  		  functional and thinks it is ready to start

  		  normal driver operations again. There is no
  		  guarantee that the driver will actually be
  		  allowed to proceed, as another driver on the
  		  same segment might have failed and thus triggered a
  		  slot reset on platforms that support it.

  		- PCI_ERS_RESULT_NEED_RESET

  		  Driver returns this if it thinks the device is not
  		  recoverable in it's current state and it needs a slot
  		  reset to proceed.

  		- PCI_ERS_RESULT_DISCONNECT

  		  Same as above. Total failure, no recovery even after
  		  reset driver dead. (To be defined more precisely)

  The next step taken depends on the results returned by the drivers.
  If all drivers returned PCI_ERS_RESULT_RECOVERED, then the platform
  proceeds to either STEP3 (Link Reset) or to STEP 5 (Resume Operations).
  
  If any driver returned PCI_ERS_RESULT_NEED_RESET, then the platform
  proceeds to STEP 4 (Slot Reset)

  >>> The current powerpc implementation does not implement this callback.

  
  STEP 3: Link Reset
  ------------------
  The platform resets the link, and then calls the link_reset() callback
  on all affected device drivers.  This is a PCI-Express specific state
  and is done whenever a non-fatal error has been detected that can be
  "solved" by resetting the link. This call informs the driver of the
  reset and the driver should check to see if the device appears to be
  in working condition.
  
  The driver is not supposed to restart normal driver I/O operations
  at this point.  It should limit itself to "probing" the device to
  check it's recoverability status. If all is right, then the platform
  will call resume() once all drivers have ack'd link_reset().

  
  	Result codes:

  		(identical to STEP 3 (MMIO Enabled)
  
  The platform then proceeds to either STEP 4 (Slot Reset) or STEP 5
  (Resume Operations).
  
  >>> The current powerpc implementation does not implement this callback.
  
  
  STEP 4: Slot Reset
  ------------------
  The platform performs a soft or hard reset of the device, and then
  calls the slot_reset() callback.
  
  A soft reset consists of asserting the adapter #RST line and then
  restoring the PCI BAR's and PCI configuration header to a state
  that is equivalent to what it would be after a fresh system
  power-on followed by power-on BIOS/system firmware initialization.
  If the platform supports PCI hotplug, then the reset might be
  performed by toggling the slot electrical power off/on.

  It is important for the platform to restore the PCI config space
  to the "fresh poweron" state, rather than the "last state". After
  a slot reset, the device driver will almost always use its standard
  device initialization routines, and an unusual config space setup
  may result in hung devices, kernel panics, or silent data corruption.

  This call gives drivers the chance to re-initialize the hardware
  (re-download firmware, etc.).  At this point, the driver may assume
  that he card is in a fresh state and is fully functional. In
  particular, interrupt generation should work normally.

  Drivers should not yet restart normal I/O processing operations
  at this point.  If all device drivers report success on this
  callback, the platform will call resume() to complete the sequence,
  and let the driver restart normal I/O processing.

  
  A driver can still return a critical failure for this function if
  it can't get the device operational after reset.  If the platform

  previously tried a soft reset, it might now try a hard reset (power

  cycle) and then call slot_reset() again.  It the device still can't
  be recovered, there is nothing more that can be done;  the platform
  will typically report a "permanent failure" in such a case.  The
  device will be considered "dead" in this case.

  Drivers for multi-function cards will need to coordinate among
  themselves as to which driver instance will perform any "one-shot"
  or global device initialization. For example, the Symbios sym53cxx2
  driver performs device init only from PCI function 0:

  +       if (PCI_FUNC(pdev->devfn) == 0)
  +               sym_reset_scsi_bus(np, 0);

  	Result codes:
  		- PCI_ERS_RESULT_DISCONNECT
  		Same as above.

  Platform proceeds either to STEP 5 (Resume Operations) or STEP 6 (Permanent
  Failure).
  
  >>> The current powerpc implementation does not currently try a
  >>> power-cycle reset if the driver returned PCI_ERS_RESULT_DISCONNECT.
  >>> However, it probably should.
  
  
  STEP 5: Resume Operations
  -------------------------
  The platform will call the resume() callback on all affected device
  drivers if all drivers on the segment have returned
  PCI_ERS_RESULT_RECOVERED from one of the 3 previous callbacks.
  The goal of this callback is to tell the driver to restart activity,
  that everything is back and running. This callback does not return
  a result code.
  
  At this point, if a new error happens, the platform will restart
  a new error recovery sequence.
  
  STEP 6: Permanent Failure
  -------------------------
  A "permanent failure" has occurred, and the platform cannot recover
  the device.  The platform will call error_detected() with a
  pci_channel_state value of pci_channel_io_perm_failure.
  
  The device driver should, at this point, assume the worst. It should
  cancel all pending I/O, refuse all new I/O, returning -EIO to
  higher layers. The device driver should then clean up all of its
  memory and remove itself from kernel operations, much as it would
  during system shutdown.
  
  The platform will typically notify the system operator of the
  permanent failure in some way.  If the device is hotplug-capable,
  the operator will probably want to remove and replace the device.
  Note, however, not all failures are truly "permanent". Some are
  caused by over-heating, some by a poorly seated card. Many
  PCI error events are caused by software bugs, e.g. DMA's to
  wild addresses or bogus split transactions due to programming
  errors. See the discussion in powerpc/eeh-pci-error-recovery.txt
  for additional detail on real-life experience of the causes of
  software errors.
  
  
  Conclusion; General Remarks
  ---------------------------
  The way those callbacks are called is platform policy. A platform with
  no slot reset capability may want to just "ignore" drivers that can't

  recover (disconnect them) and try to let other cards on the same segment
  recover. Keep in mind that in most real life cases, though, there will
  be only one driver per segment.

  Now, a note about interrupts. If you get an interrupt and your

  device is dead or has been isolated, there is a problem :)

  The current policy is to turn this into a platform policy.
  That is, the recovery API only requires that:

  
   - There is no guarantee that interrupt delivery can proceed from any
  device on the segment starting from the error detection and until the

  resume callback is sent, at which point interrupts are expected to be

  fully operational.

   - There is no guarantee that interrupt delivery is stopped, that is,
  a driver that gets an interrupt after detecting an error, or that detects
  an error within the interrupt handler such that it prevents proper

  ack'ing of the interrupt (and thus removal of the source) should just

  return IRQ_NOTHANDLED. It's up to the platform to deal with that
  condition, typically by masking the IRQ source during the duration of

  the error handling. It is expected that the platform "knows" which
  interrupts are routed to error-management capable slots and can deal

  with temporarily disabling that IRQ number during error processing (this

  isn't terribly complex). That means some IRQ latency for other devices
  sharing the interrupt, but there is simply no other way. High end
  platforms aren't supposed to share interrupts between many devices
  anyway :)

  >>> Implementation details for the powerpc platform are discussed in
  >>> the file Documentation/powerpc/eeh-pci-error-recovery.txt
  
  >>> As of this writing, there are six device drivers with patches
  >>> implementing error recovery. Not all of these patches are in
  >>> mainline yet. These may be used as "examples":
  >>>
  >>> drivers/scsi/ipr.c
  >>> drivers/scsi/sym53cxx_2
  >>> drivers/next/e100.c
  >>> drivers/net/e1000
  >>> drivers/net/ixgb
  >>> drivers/net/s2io.c
  
  The End
  -------