22 Feb, 2013
1 commit
-
Pull ARM SoC-specific updates from Arnd Bergmann:
"This is a larger set of new functionality for the existing SoC
families, including:- vt8500 gains support for new CPU cores, notably the Cortex-A9 based
wm8850- prima2 gains support for the "marco" SoC family, its SMP based
cousin- tegra gains support for the new Tegra4 (Tegra114) family
- socfpga now supports a newer version of the hardware including SMP
- i.mx31 and bcm2835 are now using DT probing for their clocks
- lots of updates for sh-mobile
- OMAP updates for clocks, power management and USB
- i.mx6q and tegra now support cpuidle
- kirkwood now supports PCIe hot plugging
- tegra clock support is updated
- tegra USB PHY probing gets implemented diffently"
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (148 commits)
ARM: prima2: remove duplicate v7_invalidate_l1
ARM: shmobile: r8a7779: Correct TMU clock support again
ARM: prima2: fix __init section for cpu hotplug
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 3/3)
ARM: OMAP: Consolidate OMAP USB-HS platform data (part 1/3)
arm: socfpga: Add SMP support for actual socfpga harware
arm: Add v7_invalidate_l1 to cache-v7.S
arm: socfpga: Add entries to enable make dtbs socfpga
arm: socfpga: Add new device tree source for actual socfpga HW
ARM: tegra: sort Kconfig selects for Tegra114
ARM: tegra: enable ARCH_REQUIRE_GPIOLIB for Tegra114
ARM: tegra: Fix build error w/ ARCH_TEGRA_114_SOC w/o ARCH_TEGRA_3x_SOC
ARM: tegra: Fix build error for gic update
ARM: tegra: remove empty tegra_smp_init_cpus()
ARM: shmobile: Register ARM architected timer
ARM: MARCO: fix the build issue due to gic-vic-to-irqchip move
ARM: shmobile: r8a7779: Correct TMU clock support
ARM: mxs_defconfig: Select CONFIG_DEVTMPFS_MOUNT
ARM: mxs: decrease mxs_clockevent_device.min_delta_ns to 2 clock cycles
ARM: mxs: use apbx bus clock to drive the timers on timrotv2
...
26 Jan, 2013
1 commit
-
Remove now-obsolete code from arch/arm/mach-omap2/omap_device.c. This
mostly consists of removing the first attempt at device PM latency
handling. This was never really used, has been replaced by the common
dev_pm_qos code, and needs to go away as part of the DT conversion.
Also, the early platform_device creation code has been removed, as it
appears to be unused.Signed-off-by: Paul Walmsley
Cc: Kevin Hilman
12 Jan, 2013
1 commit
-
This way the initcalls don't run on other SoCs on multiplatform
kernels. Otherwise we'll get something like this when booting
on vexpress:omap_hwmod: _ensure_mpu_hwmod_is_setup: MPU initiator hwmod mpu not yet registered
...
WARNING: at arch/arm/mach-omap2/pm.c:82 _init_omap_device+0x74/0x94()
_init_omap_device: could not find omap_hwmod for mpu
...
omap-dma-engine omap-dma-engine: OMAP DMA engine driver
...Tested-by: Ezequiel Garcia
Signed-off-by: Tony Lindgren
19 Oct, 2012
2 commits
-
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.Acked-by: Laurent Pinchart
Cc: Mauro Carvalho Chehab
Cc: Timo Kokkonen
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren -
Let's make omap_hwmod local to mach-omap2 for
ARM common zImage support.Signed-off-by: Tony Lindgren
18 Oct, 2012
1 commit
-
Let's make omap_device local to mach-omap2 for
ARM common zImage support.Signed-off-by: Tony Lindgren
02 Oct, 2012
1 commit
-
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
13 Sep, 2012
2 commits
-
…git/pjw/omap-pending into cleanup-makefile-sparse
smatch and string-wrapping cleanups for the OMAP subarch code.
These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.Basic build, boot, and PM logs are available here:
http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/
-
This way we can remove includes of plat/gpio.h which won't work
with the single zImage support.Note that we also remove the cpu_class_is_omap2() check
in gpio-omap.c as the drivers should not call it as we need to
make it local to arch/arm/mach-omap2 for single zImage support.While at it, arrange the related includes in the standard way.
Cc: Grant Likely
Cc: linux-mtd@lists.infradead.org
Cc: alsa-devel@alsa-project.org
Acked-by: Linus Walleij
Signed-off-by: Tony Lindgren
12 Sep, 2012
1 commit
-
Resolve the following warnings from smatch:
arch/arm/mach-omap2/gpmc.c:282 gpmc_cs_set_timings() info: why not propagate 'div' from gpmc_cs_calc_divider() instead of -1?
arch/arm/mach-omap2/serial.c:328 omap_serial_init_port() error: 'pdev' dereferencing possible ERR_PTR()
arch/arm/mach-omap2/timer.c:213 omap2_gp_clockevent_init() Error invalid range 4096 to -1
arch/arm/mach-omap2/gpio.c:63 omap2_gpio_dev_init() warn: possible memory leak of 'pdata'
arch/arm/mach-omap2/omap_hwmod.c:1478 _assert_hardreset() warn: assigning -22 to unsigned variable 'ret'
arch/arm/mach-omap2/omap_hwmod.c:1487 _assert_hardreset() warn: 4294963201 is more than 255 (max '(ret)' can be) so this is always the same.
arch/arm/mach-omap2/omap_hwmod.c:1545 _read_hardreset() warn: assigning -22 to unsigned variable 'ret'
arch/arm/mach-omap2/omap_hwmod.c:1554 _read_hardreset() warn: 4294963201 is more than 255 (max '(ret)' can be) so this is always the same.
arch/arm/mach-omap2/dpll3xxx.c:629 omap3_clkoutx2_recalc() error: we previously assumed 'pclk' could be null (see line 627)
arch/arm/mach-omap2/board-n8x0.c:422 n8x0_mmc_late_init() Error invalid range 14 to 13
arch/arm/mach-omap1/leds-h2p2-debug.c:71 h2p2_dbg_leds_event() error: potentially derefencing uninitialized 'fpga'.
arch/arm/plat-omap/mux.c:79 omap_cfg_reg() Error invalid range 4096 to -1Thanks to Tony Lindgren for pointing out that BUG()
can be disabled. The changes in the first version that removed the
subsequent return() after BUG() states have been dropped.Signed-off-by: Paul Walmsley
Cc: Tony Lindgren
11 Sep, 2012
1 commit
-
pdata and pdata->regs have been allocated in this function and
should be freed before leaving it, and in the other error handling
cases too.spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)Signed-off-by: Wei Yongjun
Acked-by: Kevin Hilman
Signed-off-by: Tony Lindgren
25 May, 2012
1 commit
-
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...Conflicts:
drivers/gpio/gpio-samsung.c
23 May, 2012
1 commit
-
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
12 May, 2012
2 commits
-
Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.Cc: Kevin Hilman
Cc: Tony Lindgren
Cc: Santosh Shilimkar
Cc: Cousson, Benoit
Cc: Grant Likely
Signed-off-by: Tarun Kanti DebBarma
Reviewed-by: Santosh Shilimkar
Tested-by: Govindraj.R
Signed-off-by: Kevin Hilman -
This cleanup got missed while implementing following:
25db711 gpio/omap: Fix IRQ handling for SPARSE_IRQ
384ebe1 gpio/omap: Add DT support to GPIO driverCc: Kevin Hilman
Cc: Tony Lindgren
Cc: Santosh Shilimkar
Cc: Cousson, Benoit
Cc: Grant Likely
Signed-off-by: Tarun Kanti DebBarma
Reviewed-by: Santosh Shilimkar
Tested-by: Govindraj.R
Signed-off-by: Kevin Hilman
18 Apr, 2012
1 commit
-
Resolve some warnings identified by cppcheck in arch/arm/mach-omap2:
[arch/arm/mach-omap2/usb-tusb6010.c:129]: (style) Checking if unsigned variable 'tmp' is less than zero.
[arch/arm/mach-omap2/prm_common.c:241]: (error) Possible null pointer dereference: irq_setup - otherwise it is redundant to check if irq_setup is null at line 247
[arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'per_clkdm' is assigned a value that is never used
[arch/arm/mach-omap2/pm34xx.c:790]: (style) Variable 'core_clkdm' is assigned a value that is never used
[arch/arm/mach-omap2/pm24xx.c:185]: (style) Variable 'only_idle' is assigned a value that is never used
[arch/arm/mach-omap2/mux.c:254]: (error) Possible null pointer dereference: mux
[arch/arm/mach-omap2/mux.c:258]: (error) Possible null pointer dereference: mux
[arch/arm/mach-omap2/gpmc-onenand.c:178]: (style) Variable 'tick_ns' is assigned a value that is never used
[arch/arm/mach-omap2/gpio.c:56]: (error) Possible null pointer dereference: pdata - otherwise it is redundant to check if pdata is null at line 57
[arch/arm/mach-omap2/devices.c:45]: (style) Variable 'l' is assigned a value that is never used
[arch/arm/mach-omap2/board-omap3evm.c:641] -> [arch/arm/mach-omap2/board-omap3evm.c:639]: (style) Found duplicate branches for if and else.
[arch/arm/mach-omap2/am35xx-emac.c:95]: (style) Variable 'regval' is assigned a value that is never used
[arch/arm/mach-omap2/devices.c:74]: (style) Variable 'l' is assigned a value that is never used
[arch/arm/mach-omap2/pm34xx.c:277]: (style) Variable 'per_prev_state' is assigned a value that is never used
[arch/arm/plat-omap/dmtimer.c:352]: (error) Possible null pointer dereference: timer - otherwise it is redundant to check if timer is null at line 354
[arch/arm/plat-omap/omap_device.c:478]: (style) Variable 'c' is assigned a value that is never used
[arch/arm/plat-omap/usb.c:42]: (style) Variable 'status' is assigned a value that is never used
[arch/arm/mach-omap1/clock.c:197]: (style) Variable 'dpll1_rate' is assigned a value that is never used
[arch/arm/mach-omap1/lcd_dma.c:60]: (style) struct or union member 'lcd_dma_info::size' is never used
[arch/arm/mach-omap1/pm.c:572]: (style) Variable 'entry' is assigned a value that is never usedSome of them are pretty good catches, such as gpio.c:56 and
usb-tusb6010.c:129.Thanks to Jarkko Nikula for some comments on the sscanf() warnings.
It seems that the kernel sscanf() ignores the field width anyway for the
%d format, so those changes have been dropped from this second version.Thanks to Daniel Marjamäki for pointing
out that a variable was unnecessarily marked static in the
board-omap3evm.c change.Signed-off-by: Paul Walmsley
Cc: Felipe Balbi
Cc: Tony Lindgren
Cc: Kevin Hilman
Cc: Peter Ujfalusi
Cc: Jarkko Nikula
Cc: Charulatha Varadarajan
Cc: Daniel Marjamäki
Cc: Tarun Kanti DebBarma
Reviewed-by: Charulatha Varadarajan # for gpio.c
16 Apr, 2012
1 commit
-
* omap/dt-missed-3.4:
arm/dts: OMAP3: Add mmc controller nodes and board data
arm/dts: OMAP4: Add mmc controller nodes and board data
arm/dts: twl: Pass regulator data from dt
arm/dts: omap4-sdp: Add ks8851 ethernet SPI device
arm/dts: OMAP3: Add SPI controller nodes
arm/dts: OMAP4: Add SPI controller nodes
arm/dts: OMAP3: Add gpio nodes
arm/dts: OMAP4: Add gpio nodes
ARM: OMAP2+: board-generic: Remove i2c static init
arm/dts: omap3-beagle: Add twl4030 and i2c EEPROM
arm/dts: omap4-sdp: Add twl6030, i2c3 and i2c4 devices
arm/dts: omap4-panda: Add twl6030 and i2c EEPROM
arm/dts: twl4030: Add DTS file for twl4030 PM + Audio IC
arm/dts: twl6030: Add DTS file for twl6030 PMIC
12 Mar, 2012
1 commit
-
Add the 6 GPIOs controller nodes present in OMAP4.
Remove gpio static device initialisation if DT is populated.
Signed-off-by: Benoit Cousson
Cc: Grant Likely
11 Mar, 2012
1 commit
-
…d/linux-omap into next/cleanup
* 'cleanup-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: PM: share some suspend-related functions across OMAP2, 3, 4
ARM: OMAP2+: omap_device: call all suspend, resume callbacks when OMAP_DEVICE_NO_IDLE_ON_SUSPEND is set
ARM: OMAP: omap_device: remove omap_device_parent
ARM: OMAP2+: PM debug: fix the use of debugfs_create_* API
ARM: OMAP2+: PM: share clkdms_setup() across OMAP2, 3, 4
ARM: OMAP2+: PM: clean up omap_set_pwrdm_state()
ARM: OMAP3: PM: remove superfluous calls to pwrdm_clear_all_prev_pwrst()
ARM: OMAP: convert omap_device_build() and callers to __init
ARM: OMAP2+: Mark omap_hsmmc_init and omap_mux related functions as __init
ARM: OMAP2+: Split omap2_hsmmc_init() to properly support I2C GPIO pins
ARM: OMAP: omap_device: Expose omap_device_{alloc, delete, register}
ARM: OMAP: Fix build error when mmc_omap is built as module
ARM: OMAP: Fix kernel panic with HSMMC when twl4030_gpio is a module
25 Feb, 2012
1 commit
-
Building omap_devices should only be done at init time, and since
omap_device_build() is using early_platform calls which are also
__init, this ensures that omap_device isn't trying to use functions
that disappear.Signed-off-by: Kevin Hilman
Signed-off-by: Tony Lindgren
06 Feb, 2012
10 commits
-
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.Signed-off-by: Charulatha V
Signed-off-by: Tarun Kanti DebBarma
Reviewed-by: Santosh Shilimkar
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.Signed-off-by: Charulatha V
Signed-off-by: Tarun Kanti DebBarma
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.Signed-off-by: Tarun Kanti DebBarma
Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.Signed-off-by: Tarun Kanti DebBarma
Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.Signed-off-by: Tarun Kanti DebBarma
Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.Signed-off-by: Charulatha V
Signed-off-by: Tarun Kanti DebBarma
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman -
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.Signed-off-by: Charulatha V
Reviewed-by: Santosh Shilimkar
Acked-by: Tony Lindgren
Reviewed-by: Kevin Hilman
Signed-off-by: Kevin Hilman
05 Oct, 2011
1 commit
-
Remove all these duplicated structures since a default one is now
available.Signed-off-by: Benoit Cousson
Signed-off-by: Kevin Hilman
16 Sep, 2011
2 commits
-
Public omap_device functions need to take platform_device pointers,
conversion to omap_device pointers is done internal to the omap_device
layer.Signed-off-by: Kevin Hilman
-
All of the device init and device driver interaction with omap_device
is done using platform_device pointers. To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.Cc: Paul Walmsley
Signed-off-by: Kevin Hilman
23 Jul, 2011
1 commit
-
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
13 Jul, 2011
1 commit
-
Until these drivers are runtime PM converted, their device power
states are managed by calling custom driver hooks late in the
idle/suspend path. Therefore, do not let the suspend/resume core code
automatically idle these devices since they will be managed manually
by the OMAP PM core very late in the idle/suspend path.Signed-off-by: Kevin Hilman
Signed-off-by: Rafael J. Wysocki
17 Jun, 2011
5 commits
-
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.Thanks to Charulatha V for finding/fixing a few -1s
that were missed in the original patch.Signed-off-by: Kevin Hilman
-
Use register offsets passed in from pdata for accessing debounce registers.
Signed-off-by: Kevin Hilman
-
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.Signed-off-by: Kevin Hilman
-
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman
-
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.Signed-off-by: Kevin Hilman