// SPDX-License-Identifier: GPL-2.0-or-later

  /*
  **	DINO manager
  **
  **	(c) Copyright 1999 Red Hat Software
  **	(c) Copyright 1999 SuSE GmbH
  **	(c) Copyright 1999,2000 Hewlett-Packard Company
  **	(c) Copyright 2000 Grant Grundler

  **	(c) Copyright 2006-2019 Helge Deller

  **

  **
  **	This module provides access to Dino PCI bus (config/IOport spaces)
  **	and helps manage Dino IRQ lines.
  **
  **	Dino interrupt handling is a bit complicated.
  **	Dino always writes to the broadcast EIR via irr0 for now.
  **	(BIG WARNING: using broadcast EIR is a really bad thing for SMP!)
  **	Only one processor interrupt is used for the 11 IRQ line 
  **	inputs to dino.
  **
  **	The different between Built-in Dino and Card-Mode
  **	dino is in chip initialization and pci device initialization.
  **
  **	Linux drivers can only use Card-Mode Dino if pci devices I/O port
  **	BARs are configured and used by the driver. Programming MMIO address 
  **	requires substantial knowledge of available Host I/O address ranges
  **	is currently not supported.  Port/Config accessor functions are the
  **	same. "BIOS" differences are handled within the existing routines.
  */
  
  /*	Changes :
  **	2001-06-14 : Clement Moyroud (moyroudc@esiee.fr)
  **		- added support for the integrated RS232. 	
  */
  
  /*
  ** TODO: create a virtual address for each Dino HPA.
  **       GSC code might be able to do this since IODC data tells us
  **       how many pages are used. PCI subsystem could (must?) do this
  **       for PCI drivers devices which implement/use MMIO registers.
  */

  #include <linux/delay.h>
  #include <linux/types.h>
  #include <linux/kernel.h>
  #include <linux/pci.h>
  #include <linux/init.h>
  #include <linux/ioport.h>
  #include <linux/slab.h>
  #include <linux/interrupt.h>	/* for struct irqaction */
  #include <linux/spinlock.h>	/* for spinlock_t and prototypes */
  
  #include <asm/pdc.h>
  #include <asm/page.h>

  #include <asm/io.h>
  #include <asm/hardware.h>
  
  #include "gsc.h"

  #include "iommu.h"

  
  #undef DINO_DEBUG
  
  #ifdef DINO_DEBUG
  #define DBG(x...) printk(x)
  #else
  #define DBG(x...)
  #endif
  
  /*
  ** Config accessor functions only pass in the 8-bit bus number
  ** and not the 8-bit "PCI Segment" number. Each Dino will be
  ** assigned a PCI bus number based on "when" it's discovered.
  **
  ** The "secondary" bus number is set to this before calling
  ** pci_scan_bus(). If any PPB's are present, the scan will
  ** discover them and update the "secondary" and "subordinate"
  ** fields in Dino's pci_bus structure.
  **
  ** Changes in the configuration *will* result in a different
  ** bus number for each dino.
  */

  #define is_card_dino(id)	((id)->hw_type == HPHW_A_DMA)
  #define is_cujo(id)		((id)->hversion == 0x682)

  
  #define DINO_IAR0		0x004
  #define DINO_IODC_ADDR		0x008
  #define DINO_IODC_DATA_0	0x008
  #define DINO_IODC_DATA_1	0x008
  #define DINO_IRR0		0x00C
  #define DINO_IAR1		0x010
  #define DINO_IRR1		0x014
  #define DINO_IMR		0x018
  #define DINO_IPR		0x01C
  #define DINO_TOC_ADDR		0x020
  #define DINO_ICR		0x024
  #define DINO_ILR		0x028
  #define DINO_IO_COMMAND		0x030
  #define DINO_IO_STATUS		0x034
  #define DINO_IO_CONTROL		0x038
  #define DINO_IO_GSC_ERR_RESP	0x040
  #define DINO_IO_ERR_INFO	0x044
  #define DINO_IO_PCI_ERR_RESP	0x048
  #define DINO_IO_FBB_EN		0x05c
  #define DINO_IO_ADDR_EN		0x060
  #define DINO_PCI_ADDR		0x064
  #define DINO_CONFIG_DATA	0x068
  #define DINO_IO_DATA		0x06c
  #define DINO_MEM_DATA		0x070	/* Dino 3.x only */
  #define DINO_GSC2X_CONFIG	0x7b4
  #define DINO_GMASK		0x800
  #define DINO_PAMR		0x804
  #define DINO_PAPR		0x808
  #define DINO_DAMODE		0x80c
  #define DINO_PCICMD		0x810
  #define DINO_PCISTS		0x814
  #define DINO_MLTIM		0x81c
  #define DINO_BRDG_FEAT		0x820
  #define DINO_PCIROR		0x824
  #define DINO_PCIWOR		0x828
  #define DINO_TLTIM		0x830
  
  #define DINO_IRQS 11		/* bits 0-10 are architected */
  #define DINO_IRR_MASK	0x5ff	/* only 10 bits are implemented */

  #define DINO_LOCAL_IRQS (DINO_IRQS+1)

  
  #define DINO_MASK_IRQ(x)	(1<<(x))
  
  #define PCIINTA   0x001
  #define PCIINTB   0x002
  #define PCIINTC   0x004
  #define PCIINTD   0x008
  #define PCIINTE   0x010
  #define PCIINTF   0x020
  #define GSCEXTINT 0x040
  /* #define xxx       0x080 - bit 7 is "default" */
  /* #define xxx    0x100 - bit 8 not used */
  /* #define xxx    0x200 - bit 9 not used */
  #define RS232INT  0x400
  
  struct dino_device
  {
  	struct pci_hba_data	hba;	/* 'C' inheritance - must be first */
  	spinlock_t		dinosaur_pen;
  	unsigned long		txn_addr; /* EIR addr to generate interrupt */ 
  	u32			txn_data; /* EIR data assign to each dino */ 
  	u32 			imr;	  /* IRQ's which are enabled */ 

  	int			global_irq[DINO_LOCAL_IRQS]; /* map IMR bit to global irq */

  #ifdef DINO_DEBUG
  	unsigned int		dino_irr0; /* save most recent IRQ line stat */
  #endif
  };

  static inline struct dino_device *DINO_DEV(struct pci_hba_data *hba)
  {
  	return container_of(hba, struct dino_device, hba);
  }

  /* Check if PCI device is behind a Card-mode Dino. */
  static int pci_dev_is_behind_card_dino(struct pci_dev *dev)
  {
  	struct dino_device *dino_dev;
  
  	dino_dev = DINO_DEV(parisc_walk_tree(dev->bus->bridge));
  	return is_card_dino(&dino_dev->hba.dev->id);
  }

  /*
   * Dino Configuration Space Accessor Functions
   */
  
  #define DINO_CFG_TOK(bus,dfn,pos) ((u32) ((bus)<<16 | (dfn)<<8 | (pos)))
  
  /*
   * keep the current highest bus count to assist in allocating busses.  This
   * tries to keep a global bus count total so that when we discover an 
   * entirely new bus, it can be given a unique bus number.
   */
  static int dino_current_bus = 0;
  
  static int dino_cfg_read(struct pci_bus *bus, unsigned int devfn, int where,
  		int size, u32 *val)
  {
  	struct dino_device *d = DINO_DEV(parisc_walk_tree(bus->bridge));

  	u32 local_bus = (bus->parent == NULL) ? 0 : bus->busn_res.start;

  	u32 v = DINO_CFG_TOK(local_bus, devfn, where & ~3);
  	void __iomem *base_addr = d->hba.base_addr;
  	unsigned long flags;

  	DBG("%s: %p, %d, %d, %d
  ", __func__, base_addr, devfn, where,

  									size);

  	spin_lock_irqsave(&d->dinosaur_pen, flags);
  
  	/* tell HW which CFG address */
  	__raw_writel(v, base_addr + DINO_PCI_ADDR);
  
  	/* generate cfg read cycle */
  	if (size == 1) {
  		*val = readb(base_addr + DINO_CONFIG_DATA + (where & 3));
  	} else if (size == 2) {
  		*val = readw(base_addr + DINO_CONFIG_DATA + (where & 2));
  	} else if (size == 4) {
  		*val = readl(base_addr + DINO_CONFIG_DATA);
  	}
  
  	spin_unlock_irqrestore(&d->dinosaur_pen, flags);
  	return 0;
  }
  
  /*
   * Dino address stepping "feature":
   * When address stepping, Dino attempts to drive the bus one cycle too soon
   * even though the type of cycle (config vs. MMIO) might be different. 
   * The read of Ven/Prod ID is harmless and avoids Dino's address stepping.
   */
  static int dino_cfg_write(struct pci_bus *bus, unsigned int devfn, int where,
  	int size, u32 val)
  {
  	struct dino_device *d = DINO_DEV(parisc_walk_tree(bus->bridge));

  	u32 local_bus = (bus->parent == NULL) ? 0 : bus->busn_res.start;

  	u32 v = DINO_CFG_TOK(local_bus, devfn, where & ~3);
  	void __iomem *base_addr = d->hba.base_addr;
  	unsigned long flags;

  	DBG("%s: %p, %d, %d, %d
  ", __func__, base_addr, devfn, where,

  									size);

  	spin_lock_irqsave(&d->dinosaur_pen, flags);
  
  	/* avoid address stepping feature */
  	__raw_writel(v & 0xffffff00, base_addr + DINO_PCI_ADDR);
  	__raw_readl(base_addr + DINO_CONFIG_DATA);
  
  	/* tell HW which CFG address */
  	__raw_writel(v, base_addr + DINO_PCI_ADDR);
  	/* generate cfg read cycle */
  	if (size == 1) {
  		writeb(val, base_addr + DINO_CONFIG_DATA + (where & 3));
  	} else if (size == 2) {
  		writew(val, base_addr + DINO_CONFIG_DATA + (where & 2));
  	} else if (size == 4) {
  		writel(val, base_addr + DINO_CONFIG_DATA);
  	}
  
  	spin_unlock_irqrestore(&d->dinosaur_pen, flags);
  	return 0;
  }
  
  static struct pci_ops dino_cfg_ops = {
  	.read =		dino_cfg_read,
  	.write =	dino_cfg_write,
  };
  
  
  /*
   * Dino "I/O Port" Space Accessor Functions
   *
   * Many PCI devices don't require use of I/O port space (eg Tulip,
   * NCR720) since they export the same registers to both MMIO and
   * I/O port space.  Performance is going to stink if drivers use
   * I/O port instead of MMIO.
   */
  
  #define DINO_PORT_IN(type, size, mask) \
  static u##size dino_in##size (struct pci_hba_data *d, u16 addr) \
  { \
  	u##size v; \
  	unsigned long flags; \
  	spin_lock_irqsave(&(DINO_DEV(d)->dinosaur_pen), flags); \
  	/* tell HW which IO Port address */ \
  	__raw_writel((u32) addr, d->base_addr + DINO_PCI_ADDR); \
  	/* generate I/O PORT read cycle */ \
  	v = read##type(d->base_addr+DINO_IO_DATA+(addr&mask)); \
  	spin_unlock_irqrestore(&(DINO_DEV(d)->dinosaur_pen), flags); \
  	return v; \
  }
  
  DINO_PORT_IN(b,  8, 3)
  DINO_PORT_IN(w, 16, 2)
  DINO_PORT_IN(l, 32, 0)
  
  #define DINO_PORT_OUT(type, size, mask) \
  static void dino_out##size (struct pci_hba_data *d, u16 addr, u##size val) \
  { \
  	unsigned long flags; \
  	spin_lock_irqsave(&(DINO_DEV(d)->dinosaur_pen), flags); \
  	/* tell HW which IO port address */ \
  	__raw_writel((u32) addr, d->base_addr + DINO_PCI_ADDR); \
  	/* generate cfg write cycle */ \
  	write##type(val, d->base_addr+DINO_IO_DATA+(addr&mask)); \
  	spin_unlock_irqrestore(&(DINO_DEV(d)->dinosaur_pen), flags); \
  }
  
  DINO_PORT_OUT(b,  8, 3)
  DINO_PORT_OUT(w, 16, 2)
  DINO_PORT_OUT(l, 32, 0)

  static struct pci_port_ops dino_port_ops = {

  	.inb	= dino_in8,
  	.inw	= dino_in16,
  	.inl	= dino_in32,
  	.outb	= dino_out8,
  	.outw	= dino_out16,
  	.outl	= dino_out32
  };

  static void dino_mask_irq(struct irq_data *d)

  {

  	struct dino_device *dino_dev = irq_data_get_irq_chip_data(d);
  	int local_irq = gsc_find_local_irq(d->irq, dino_dev->global_irq, DINO_LOCAL_IRQS);

  	DBG(KERN_WARNING "%s(0x%px, %d)
  ", __func__, dino_dev, d->irq);

  
  	/* Clear the matching bit in the IMR register */
  	dino_dev->imr &= ~(DINO_MASK_IRQ(local_irq));
  	__raw_writel(dino_dev->imr, dino_dev->hba.base_addr+DINO_IMR);
  }

  static void dino_unmask_irq(struct irq_data *d)

  {

  	struct dino_device *dino_dev = irq_data_get_irq_chip_data(d);
  	int local_irq = gsc_find_local_irq(d->irq, dino_dev->global_irq, DINO_LOCAL_IRQS);

  	u32 tmp;

  	DBG(KERN_WARNING "%s(0x%px, %d)
  ", __func__, dino_dev, d->irq);

  
  	/*
  	** clear pending IRQ bits
  	**
  	** This does NOT change ILR state!
  	** See comment below for ILR usage.
  	*/
  	__raw_readl(dino_dev->hba.base_addr+DINO_IPR);
  
  	/* set the matching bit in the IMR register */
  	dino_dev->imr |= DINO_MASK_IRQ(local_irq);	/* used in dino_isr() */
  	__raw_writel( dino_dev->imr, dino_dev->hba.base_addr+DINO_IMR);
  
  	/* Emulate "Level Triggered" Interrupt
  	** Basically, a driver is blowing it if the IRQ line is asserted
  	** while the IRQ is disabled.  But tulip.c seems to do that....
  	** Give 'em a kluge award and a nice round of applause!
  	**
  	** The gsc_write will generate an interrupt which invokes dino_isr().
  	** dino_isr() will read IPR and find nothing. But then catch this
  	** when it also checks ILR.
  	*/
  	tmp = __raw_readl(dino_dev->hba.base_addr+DINO_ILR);
  	if (tmp & DINO_MASK_IRQ(local_irq)) {
  		DBG(KERN_WARNING "%s(): IRQ asserted! (ILR 0x%x)
  ",

  				__func__, tmp);

  		gsc_writel(dino_dev->txn_data, dino_dev->txn_addr);
  	}
  }

  static struct irq_chip dino_interrupt_type = {

  	.name		= "GSC-PCI",
  	.irq_unmask	= dino_unmask_irq,
  	.irq_mask	= dino_mask_irq,

  };
  
  
  /*
   * Handle a Processor interrupt generated by Dino.
   *
   * ilr_loop counter is a kluge to prevent a "stuck" IRQ line from
   * wedging the CPU. Could be removed or made optional at some point.
   */

  static irqreturn_t dino_isr(int irq, void *intr_dev)

  {
  	struct dino_device *dino_dev = intr_dev;
  	u32 mask;
  	int ilr_loop = 100;
  
  	/* read and acknowledge pending interrupts */
  #ifdef DINO_DEBUG
  	dino_dev->dino_irr0 =
  #endif
  	mask = __raw_readl(dino_dev->hba.base_addr+DINO_IRR0) & DINO_IRR_MASK;
  
  	if (mask == 0)
  		return IRQ_NONE;
  
  ilr_again:
  	do {
  		int local_irq = __ffs(mask);
  		int irq = dino_dev->global_irq[local_irq];
  		DBG(KERN_DEBUG "%s(%d, %p) mask 0x%x
  ",

  			__func__, irq, intr_dev, mask);

  		generic_handle_irq(irq);

  		mask &= ~DINO_MASK_IRQ(local_irq);

  	} while (mask);
  
  	/* Support for level triggered IRQ lines.
  	** 
  	** Dropping this support would make this routine *much* faster.
  	** But since PCI requires level triggered IRQ line to share lines...
  	** device drivers may assume lines are level triggered (and not
  	** edge triggered like EISA/ISA can be).
  	*/
  	mask = __raw_readl(dino_dev->hba.base_addr+DINO_ILR) & dino_dev->imr;
  	if (mask) {
  		if (--ilr_loop > 0)
  			goto ilr_again;

  		pr_warn_ratelimited("Dino 0x%px: stuck interrupt %d
  ",

  		       dino_dev->hba.base_addr, mask);

  	}
  	return IRQ_HANDLED;
  }
  
  static void dino_assign_irq(struct dino_device *dino, int local_irq, int *irqp)
  {
  	int irq = gsc_assign_irq(&dino_interrupt_type, dino);
  	if (irq == NO_IRQ)
  		return;
  
  	*irqp = irq;
  	dino->global_irq[local_irq] = irq;
  }
  
  static void dino_choose_irq(struct parisc_device *dev, void *ctrl)
  {
  	int irq;
  	struct dino_device *dino = ctrl;
  
  	switch (dev->id.sversion) {
  		case 0x00084:	irq =  8; break; /* PS/2 */
  		case 0x0008c:	irq = 10; break; /* RS232 */
  		case 0x00096:	irq =  8; break; /* PS/2 */
  		default:	return;		 /* Unknown */
  	}
  
  	dino_assign_irq(dino, irq, &dev->irq);
  }

  
  /*
   * Cirrus 6832 Cardbus reports wrong irq on RDI Tadpole PARISC Laptop (deller@gmx.de)
   * (the irqs are off-by-one, not sure yet if this is a cirrus, dino-hardware or dino-driver problem...)
   */

  static void quirk_cirrus_cardbus(struct pci_dev *dev)

  {
  	u8 new_irq = dev->irq - 1;
  	printk(KERN_INFO "PCI: Cirrus Cardbus IRQ fixup for %s, from %d to %d
  ",
  			pci_name(dev), dev->irq, new_irq);
  	dev->irq = new_irq;
  }
  DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_CIRRUS, PCI_DEVICE_ID_CIRRUS_6832, quirk_cirrus_cardbus );

  #ifdef CONFIG_TULIP
  static void pci_fixup_tulip(struct pci_dev *dev)
  {
  	if (!pci_dev_is_behind_card_dino(dev))
  		return;
  	if (!(pci_resource_flags(dev, 1) & IORESOURCE_MEM))
  		return;
  	pr_warn("%s: HP HSC-PCI Cards with card-mode Dino not yet supported.
  ",
  		pci_name(dev));
  	/* Disable this card by zeroing the PCI resources */
  	memset(&dev->resource[0], 0, sizeof(dev->resource[0]));
  	memset(&dev->resource[1], 0, sizeof(dev->resource[1]));
  }
  DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_DEC, PCI_ANY_ID, pci_fixup_tulip);
  #endif /* CONFIG_TULIP */

  static void __init
  dino_bios_init(void)
  {
  	DBG("dino_bios_init
  ");
  }
  
  /*
   * dino_card_setup - Set up the memory space for a Dino in card mode.
   * @bus: the bus under this dino
   *
   * Claim an 8MB chunk of unused IO space and call the generic PCI routines
   * to set up the addresses of the devices on this bus.
   */
  #define _8MB 0x00800000UL
  static void __init
  dino_card_setup(struct pci_bus *bus, void __iomem *base_addr)
  {
  	int i;
  	struct dino_device *dino_dev = DINO_DEV(parisc_walk_tree(bus->bridge));
  	struct resource *res;
  	char name[128];
  	int size;
  
  	res = &dino_dev->hba.lmmio_space;
  	res->flags = IORESOURCE_MEM;
  	size = scnprintf(name, sizeof(name), "Dino LMMIO (%s)", 

  			 dev_name(bus->bridge));

  	res->name = kmalloc(size+1, GFP_KERNEL);
  	if(res->name)
  		strcpy((char *)res->name, name);
  	else
  		res->name = dino_dev->hba.lmmio_space.name;
  	
  
  	if (ccio_allocate_resource(dino_dev->hba.dev, res, _8MB,
  				F_EXTEND(0xf0000000UL) | _8MB,
  				F_EXTEND(0xffffffffUL) &~ _8MB, _8MB) < 0) {

  		struct pci_dev *dev, *tmp;

  
  		printk(KERN_ERR "Dino: cannot attach bus %s
  ",

  		       dev_name(bus->bridge));

  		/* kill the bus, we can't do anything with it */

  		list_for_each_entry_safe(dev, tmp, &bus->devices, bus_list) {

  			list_del(&dev->bus_list);
  		}
  			
  		return;
  	}
  	bus->resource[1] = res;
  	bus->resource[0] = &(dino_dev->hba.io_space);
  
  	/* Now tell dino what range it has */
  	for (i = 1; i < 31; i++) {
  		if (res->start == F_EXTEND(0xf0000000UL | (i * _8MB)))
  			break;
  	}

  	DBG("DINO GSC WRITE i=%d, start=%lx, dino addr = %p
  ",

  	    i, res->start, base_addr + DINO_IO_ADDR_EN);
  	__raw_writel(1 << i, base_addr + DINO_IO_ADDR_EN);
  }
  
  static void __init
  dino_card_fixup(struct pci_dev *dev)
  {
  	u32 irq_pin;
  
  	/*
  	** REVISIT: card-mode PCI-PCI expansion chassis do exist.
  	**         Not sure they were ever productized.
  	**         Die here since we'll die later in dino_inb() anyway.
  	*/
  	if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
  		panic("Card-Mode Dino: PCI-PCI Bridge not supported
  ");
  	}
  
  	/*
  	** Set Latency Timer to 0xff (not a shared bus)
  	** Set CACHELINE_SIZE.
  	*/
  	dino_cfg_write(dev->bus, dev->devfn, 
  		       PCI_CACHE_LINE_SIZE, 2, 0xff00 | L1_CACHE_BYTES/4); 
  
  	/*
  	** Program INT_LINE for card-mode devices.
  	** The cards are hardwired according to this algorithm.
  	** And it doesn't matter if PPB's are present or not since
  	** the IRQ lines bypass the PPB.
  	**
  	** "-1" converts INTA-D (1-4) to PCIINTA-D (0-3) range.
  	** The additional "-1" adjusts for skewing the IRQ<->slot.
  	*/
  	dino_cfg_read(dev->bus, dev->devfn, PCI_INTERRUPT_PIN, 1, &irq_pin); 

  	dev->irq = pci_swizzle_interrupt_pin(dev, irq_pin) - 1;

  
  	/* Shouldn't really need to do this but it's in case someone tries
  	** to bypass PCI services and look at the card themselves.
  	*/
  	dino_cfg_write(dev->bus, dev->devfn, PCI_INTERRUPT_LINE, 1, dev->irq); 
  }
  
  /* The alignment contraints for PCI bridges under dino */
  #define DINO_BRIDGE_ALIGN 0x100000
  
  
  static void __init
  dino_fixup_bus(struct pci_bus *bus)
  {

          struct pci_dev *dev;
          struct dino_device *dino_dev = DINO_DEV(parisc_walk_tree(bus->bridge));

  	DBG(KERN_WARNING "%s(0x%px) bus %d platform_data 0x%px
  ",

  	    __func__, bus, bus->busn_res.start,

  	    bus->bridge->platform_data);
  
  	/* Firmware doesn't set up card-mode dino, so we have to */
  	if (is_card_dino(&dino_dev->hba.dev->id)) {
  		dino_card_setup(bus, dino_dev->hba.base_addr);

  	} else if (bus->parent) {

  		int i;

  		pci_read_bridge_bases(bus);

  		for(i = PCI_BRIDGE_RESOURCES; i < PCI_NUM_RESOURCES; i++) {
  			if((bus->self->resource[i].flags & 
  			    (IORESOURCE_IO | IORESOURCE_MEM)) == 0)
  				continue;
  			
  			if(bus->self->resource[i].flags & IORESOURCE_MEM) {
  				/* There's a quirk to alignment of
  				 * bridge memory resources: the start
  				 * is the alignment and start-end is
  				 * the size.  However, firmware will
  				 * have assigned start and end, so we
  				 * need to take this into account */
  				bus->self->resource[i].end = bus->self->resource[i].end - bus->self->resource[i].start + DINO_BRIDGE_ALIGN;
  				bus->self->resource[i].start = DINO_BRIDGE_ALIGN;
  				
  			}
  					

  			DBG("DEBUG %s assigning %d [%pR]
  ",

  			    dev_name(&bus->self->dev), i,

  			    &bus->self->resource[i]);

  			WARN_ON(pci_assign_resource(bus->self, i));

  			DBG("DEBUG %s after assign %d [%pR]
  ",

  			    dev_name(&bus->self->dev), i,

  			    &bus->self->resource[i]);

  		}
  	}

  	list_for_each_entry(dev, &bus->devices, bus_list) {

  		if (is_card_dino(&dino_dev->hba.dev->id))
  			dino_card_fixup(dev);
  
  		/*
  		** P2PB's only have 2 BARs, no IRQs.
  		** I'd like to just ignore them for now.
  		*/

  		if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI)  {
  			pcibios_init_bridge(dev);

  			continue;

  		}

  		/* null out the ROM resource if there is one (we don't
  		 * care about an expansion rom on parisc, since it
  		 * usually contains (x86) bios code) */
  		dev->resource[PCI_ROM_RESOURCE].flags = 0;
  				
  		if(dev->irq == 255) {
  
  #define DINO_FIX_UNASSIGNED_INTERRUPTS
  #ifdef DINO_FIX_UNASSIGNED_INTERRUPTS
  
  			/* This code tries to assign an unassigned
  			 * interrupt.  Leave it disabled unless you
  			 * *really* know what you're doing since the
  			 * pin<->interrupt line mapping varies by bus
  			 * and machine */
  
  			u32 irq_pin;
  			
  			dino_cfg_read(dev->bus, dev->devfn, 
  				      PCI_INTERRUPT_PIN, 1, &irq_pin);

  			irq_pin = pci_swizzle_interrupt_pin(dev, irq_pin) - 1;

  			printk(KERN_WARNING "Device %s has undefined IRQ, "
  					"setting to %d
  ", pci_name(dev), irq_pin);
  			dino_cfg_write(dev->bus, dev->devfn, 
  				       PCI_INTERRUPT_LINE, 1, irq_pin);
  			dino_assign_irq(dino_dev, irq_pin, &dev->irq);
  #else
  			dev->irq = 65535;
  			printk(KERN_WARNING "Device %s has unassigned IRQ
  ", pci_name(dev));
  #endif
  		} else {

  			/* Adjust INT_LINE for that busses region */
  			dino_assign_irq(dino_dev, dev->irq, &dev->irq);
  		}
  	}
  }

  static struct pci_bios_ops dino_bios_ops = {

  	.init		= dino_bios_init,
  	.fixup_bus	= dino_fixup_bus
  };
  
  
  /*
   *	Initialise a DINO controller chip
   */
  static void __init
  dino_card_init(struct dino_device *dino_dev)
  {
  	u32 brdg_feat = 0x00784e05;

  	unsigned long status;
  
  	status = __raw_readl(dino_dev->hba.base_addr+DINO_IO_STATUS);
  	if (status & 0x0000ff80) {
  		__raw_writel(0x00000005,
  				dino_dev->hba.base_addr+DINO_IO_COMMAND);
  		udelay(1);
  	}

  
  	__raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_GMASK);
  	__raw_writel(0x00000001, dino_dev->hba.base_addr+DINO_IO_FBB_EN);
  	__raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_ICR);
  
  #if 1
  /* REVISIT - should be a runtime check (eg if (CPU_IS_PCX_L) ...) */
  	/*
  	** PCX-L processors don't support XQL like Dino wants it.
  	** PCX-L2 ignore XQL signal and it doesn't matter.
  	*/
  	brdg_feat &= ~0x4;	/* UXQL */
  #endif
  	__raw_writel( brdg_feat, dino_dev->hba.base_addr+DINO_BRDG_FEAT);
  
  	/*
  	** Don't enable address decoding until we know which I/O range
  	** currently is available from the host. Only affects MMIO
  	** and not I/O port space.
  	*/
  	__raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_IO_ADDR_EN);
  
  	__raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_DAMODE);
  	__raw_writel(0x00222222, dino_dev->hba.base_addr+DINO_PCIROR);
  	__raw_writel(0x00222222, dino_dev->hba.base_addr+DINO_PCIWOR);
  
  	__raw_writel(0x00000040, dino_dev->hba.base_addr+DINO_MLTIM);
  	__raw_writel(0x00000080, dino_dev->hba.base_addr+DINO_IO_CONTROL);
  	__raw_writel(0x0000008c, dino_dev->hba.base_addr+DINO_TLTIM);
  
  	/* Disable PAMR before writing PAPR */
  	__raw_writel(0x0000007e, dino_dev->hba.base_addr+DINO_PAMR);
  	__raw_writel(0x0000007f, dino_dev->hba.base_addr+DINO_PAPR);
  	__raw_writel(0x00000000, dino_dev->hba.base_addr+DINO_PAMR);
  
  	/*
  	** Dino ERS encourages enabling FBB (0x6f).
  	** We can't until we know *all* devices below us can support it.
  	** (Something in device configuration header tells us).
  	*/
  	__raw_writel(0x0000004f, dino_dev->hba.base_addr+DINO_PCICMD);
  
  	/* Somewhere, the PCI spec says give devices 1 second
  	** to recover from the #RESET being de-asserted.
  	** Experience shows most devices only need 10ms.
  	** This short-cut speeds up booting significantly.
  	*/
  	mdelay(pci_post_reset_delay);
  }
  
  static int __init
  dino_bridge_init(struct dino_device *dino_dev, const char *name)
  {
  	unsigned long io_addr;
  	int result, i, count=0;
  	struct resource *res, *prevres = NULL;
  	/*
  	 * Decoding IO_ADDR_EN only works for Built-in Dino
  	 * since PDC has already initialized this.
  	 */
  
  	io_addr = __raw_readl(dino_dev->hba.base_addr + DINO_IO_ADDR_EN);
  	if (io_addr == 0) {
  		printk(KERN_WARNING "%s: No PCI devices enabled.
  ", name);
  		return -ENODEV;
  	}
  
  	res = &dino_dev->hba.lmmio_space;
  	for (i = 0; i < 32; i++) {
  		unsigned long start, end;
  
  		if((io_addr & (1 << i)) == 0)
  			continue;

  		start = F_EXTEND(0xf0000000UL) | (i << 23);

  		end = start + 8 * 1024 * 1024 - 1;
  
  		DBG("DINO RANGE %d is at 0x%lx-0x%lx
  ", count,
  		    start, end);
  
  		if(prevres && prevres->end + 1 == start) {
  			prevres->end = end;
  		} else {
  			if(count >= DINO_MAX_LMMIO_RESOURCES) {
  				printk(KERN_ERR "%s is out of resource windows for range %d (0x%lx-0x%lx)
  ", name, count, start, end);
  				break;
  			}
  			prevres = res;
  			res->start = start;
  			res->end = end;
  			res->flags = IORESOURCE_MEM;
  			res->name = kmalloc(64, GFP_KERNEL);
  			if(res->name)
  				snprintf((char *)res->name, 64, "%s LMMIO %d",
  					 name, count);
  			res++;
  			count++;
  		}
  	}
  
  	res = &dino_dev->hba.lmmio_space;
  
  	for(i = 0; i < DINO_MAX_LMMIO_RESOURCES; i++) {
  		if(res[i].flags == 0)
  			break;
  
  		result = ccio_request_resource(dino_dev->hba.dev, &res[i]);
  		if (result < 0) {

  			printk(KERN_ERR "%s: failed to claim PCI Bus address "

  			       "space %d (%pR)!
  ", name, i, &res[i]);

  			return result;
  		}
  	}
  	return 0;
  }
  
  static int __init dino_common_init(struct parisc_device *dev,
  		struct dino_device *dino_dev, const char *name)
  {
  	int status;
  	u32 eim;
  	struct gsc_irq gsc_irq;
  	struct resource *res;
  
  	pcibios_register_hba(&dino_dev->hba);
  
  	pci_bios = &dino_bios_ops;   /* used by pci_scan_bus() */
  	pci_port = &dino_port_ops;
  
  	/*
  	** Note: SMP systems can make use of IRR1/IAR1 registers
  	**   But it won't buy much performance except in very
  	**   specific applications/configurations. Note Dino
  	**   still only has 11 IRQ input lines - just map some of them
  	**   to a different processor.
  	*/
  	dev->irq = gsc_alloc_irq(&gsc_irq);
  	dino_dev->txn_addr = gsc_irq.txn_addr;
  	dino_dev->txn_data = gsc_irq.txn_data;
  	eim = ((u32) gsc_irq.txn_addr) | gsc_irq.txn_data;
  
  	/* 
  	** Dino needs a PA "IRQ" to get a processor's attention.
  	** arch/parisc/kernel/irq.c returns an EIRR bit.
  	*/
  	if (dev->irq < 0) {
  		printk(KERN_WARNING "%s: gsc_alloc_irq() failed
  ", name);
  		return 1;
  	}
  
  	status = request_irq(dev->irq, dino_isr, 0, name, dino_dev);
  	if (status) {
  		printk(KERN_WARNING "%s: request_irq() failed with %d
  ", 
  			name, status);
  		return 1;
  	}
  
  	/* Support the serial port which is sometimes attached on built-in
  	 * Dino / Cujo chips.
  	 */
  
  	gsc_fixup_irqs(dev, dino_dev, dino_choose_irq);
  
  	/*
  	** This enables DINO to generate interrupts when it sees
  	** any of its inputs *change*. Just asserting an IRQ
  	** before it's enabled (ie unmasked) isn't good enough.
  	*/
  	__raw_writel(eim, dino_dev->hba.base_addr+DINO_IAR0);
  
  	/*
  	** Some platforms don't clear Dino's IRR0 register at boot time.
  	** Reading will clear it now.
  	*/
  	__raw_readl(dino_dev->hba.base_addr+DINO_IRR0);
  
  	/* allocate I/O Port resource region */
  	res = &dino_dev->hba.io_space;

  	if (!is_cujo(&dev->id)) {

  		res->name = "Dino I/O Port";
  	} else {
  		res->name = "Cujo I/O Port";
  	}
  	res->start = HBA_PORT_BASE(dino_dev->hba.hba_num);
  	res->end = res->start + (HBA_PORT_SPACE_SIZE - 1);
  	res->flags = IORESOURCE_IO; /* do not mark it busy ! */
  	if (request_resource(&ioport_resource, res) < 0) {
  		printk(KERN_ERR "%s: request I/O Port region failed "

  		       "0x%lx/%lx (hpa 0x%px)
  ",

  		       name, (unsigned long)res->start, (unsigned long)res->end,
  		       dino_dev->hba.base_addr);

  		return 1;
  	}
  
  	return 0;
  }
  
  #define CUJO_RAVEN_ADDR		F_EXTEND(0xf1000000UL)
  #define CUJO_FIREHAWK_ADDR	F_EXTEND(0xf1604000UL)
  #define CUJO_RAVEN_BADPAGE	0x01003000UL
  #define CUJO_FIREHAWK_BADPAGE	0x01607000UL

  static const char dino_vers[][4] = {

  	"2.0",
  	"2.1",
  	"3.0",
  	"3.1"
  };

  static const char cujo_vers[][4] = {

  	"1.0",
  	"2.0"
  };
  
  void ccio_cujo20_fixup(struct parisc_device *dev, u32 iovp);
  
  /*
  ** Determine if dino should claim this chip (return 0) or not (return 1).
  ** If so, initialize the chip appropriately (card-mode vs bridge mode).
  ** Much of the initialization is common though.
  */

  static int __init dino_probe(struct parisc_device *dev)

  {
  	struct dino_device *dino_dev;	// Dino specific control struct
  	const char *version = "unknown";
  	char *name;
  	int is_cujo = 0;

  	LIST_HEAD(resources);

  	struct pci_bus *bus;

  	unsigned long hpa = dev->hpa.start;

  	int max;

  	name = "Dino";
  	if (is_card_dino(&dev->id)) {
  		version = "3.x (card mode)";
  	} else {

  		if (!is_cujo(&dev->id)) {

  			if (dev->id.hversion_rev < 4) {
  				version = dino_vers[dev->id.hversion_rev];
  			}
  		} else {
  			name = "Cujo";
  			is_cujo = 1;
  			if (dev->id.hversion_rev < 2) {
  				version = cujo_vers[dev->id.hversion_rev];
  			}
  		}
  	}

  	printk("%s version %s found at 0x%lx
  ", name, version, hpa);

  	if (!request_mem_region(hpa, PAGE_SIZE, name)) {

  		printk(KERN_ERR "DINO: Hey! Someone took my MMIO space (0x%lx)!
  ",

  			hpa);

  		return 1;
  	}
  
  	/* Check for bugs */
  	if (is_cujo && dev->id.hversion_rev == 1) {
  #ifdef CONFIG_IOMMU_CCIO
  		printk(KERN_WARNING "Enabling Cujo 2.0 bug workaround
  ");

  		if (hpa == (unsigned long)CUJO_RAVEN_ADDR) {

  			ccio_cujo20_fixup(dev, CUJO_RAVEN_BADPAGE);

  		} else if (hpa == (unsigned long)CUJO_FIREHAWK_ADDR) {

  			ccio_cujo20_fixup(dev, CUJO_FIREHAWK_BADPAGE);
  		} else {

  			printk("Don't recognise Cujo at address 0x%lx, not enabling workaround
  ", hpa);

  		}
  #endif
  	} else if (!is_cujo && !is_card_dino(&dev->id) &&
  			dev->id.hversion_rev < 3) {
  		printk(KERN_WARNING
  "The GSCtoPCI (Dino hrev %d) bus converter found may exhibit
  "
  "data corruption.  See Service Note Numbers: A4190A-01, A4191A-01.
  "
  "Systems shipped after Aug 20, 1997 will not exhibit this problem.
  "
  "Models affected: C180, C160, C160L, B160L, and B132L workstations.
  
  ",
  			dev->id.hversion_rev);
  /* REVISIT: why are C200/C240 listed in the README table but not
  **   "Models affected"? Could be an omission in the original literature.
  */
  	}

  	dino_dev = kzalloc(sizeof(struct dino_device), GFP_KERNEL);

  	if (!dino_dev) {
  		printk("dino_init_chip - couldn't alloc dino_device
  ");
  		return 1;
  	}

  	dino_dev->hba.dev = dev;

  	dino_dev->hba.base_addr = ioremap(hpa, 4096);

  	dino_dev->hba.lmmio_space_offset = PCI_F_EXTEND;

  	spin_lock_init(&dino_dev->dinosaur_pen);
  	dino_dev->hba.iommu = ccio_get_iommu(dev);
  
  	if (is_card_dino(&dev->id)) {
  		dino_card_init(dino_dev);
  	} else {
  		dino_bridge_init(dino_dev, name);
  	}
  
  	if (dino_common_init(dev, dino_dev, name))
  		return 1;
  
  	dev->dev.platform_data = dino_dev;

  	pci_add_resource_offset(&resources, &dino_dev->hba.io_space,
  				HBA_PORT_BASE(dino_dev->hba.hba_num));

  	if (dino_dev->hba.lmmio_space.flags)

  		pci_add_resource_offset(&resources, &dino_dev->hba.lmmio_space,
  					dino_dev->hba.lmmio_space_offset);

  	if (dino_dev->hba.elmmio_space.flags)

  		pci_add_resource_offset(&resources, &dino_dev->hba.elmmio_space,
  					dino_dev->hba.lmmio_space_offset);

  	if (dino_dev->hba.gmmio_space.flags)
  		pci_add_resource(&resources, &dino_dev->hba.gmmio_space);

  	dino_dev->hba.bus_num.start = dino_current_bus;
  	dino_dev->hba.bus_num.end = 255;
  	dino_dev->hba.bus_num.flags = IORESOURCE_BUS;
  	pci_add_resource(&resources, &dino_dev->hba.bus_num);

  	/*
  	** It's not used to avoid chicken/egg problems
  	** with configuration accessor functions.
  	*/

  	dino_dev->hba.hba_bus = bus = pci_create_root_bus(&dev->dev,
  			 dino_current_bus, &dino_cfg_ops, NULL, &resources);

  	if (!bus) {

  		printk(KERN_ERR "ERROR: failed to scan PCI bus on %s (duplicate bus number %d?)
  ",

  		       dev_name(&dev->dev), dino_current_bus);

  		pci_free_resource_list(&resources);

  		/* increment the bus number in case of duplicates */
  		dino_current_bus++;

  		return 0;

  	}

  	max = pci_scan_child_bus(bus);
  	pci_bus_update_busn_res_end(bus, max);

  
  	/* This code *depends* on scanning being single threaded
  	 * if it isn't, this global bus number count will fail
  	 */

  	dino_current_bus = max + 1;

  	pci_bus_assign_resources(bus);
  	pci_bus_add_devices(bus);

  	return 0;
  }
  
  /*
   * Normally, we would just test sversion.  But the Elroy PCI adapter has
   * the same sversion as Dino, so we have to check hversion as well.
   * Unfortunately, the J2240 PDC reports the wrong hversion for the first
   * Dino, so we have to test for Dino, Cujo and Dino-in-a-J2240.
   * For card-mode Dino, most machines report an sversion of 9D.  But 715
   * and 725 firmware misreport it as 0x08080 for no adequately explained
   * reason.
   */

  static const struct parisc_device_id dino_tbl[] __initconst = {

  	{ HPHW_A_DMA, HVERSION_REV_ANY_ID, 0x004, 0x0009D },/* Card-mode Dino */
  	{ HPHW_A_DMA, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x08080 }, /* XXX */
  	{ HPHW_BRIDGE, HVERSION_REV_ANY_ID, 0x680, 0xa }, /* Bridge-mode Dino */
  	{ HPHW_BRIDGE, HVERSION_REV_ANY_ID, 0x682, 0xa }, /* Bridge-mode Cujo */
  	{ HPHW_BRIDGE, HVERSION_REV_ANY_ID, 0x05d, 0xa }, /* Dino in a J2240 */
  	{ 0, }
  };

  static struct parisc_driver dino_driver __refdata = {

  	.name =		"dino",

  	.id_table =	dino_tbl,

  	.probe =	dino_probe,

  };
  
  /*
   * One time initialization to let the world know Dino is here.
   * This is the only routine which is NOT static.
   * Must be called exactly once before pci_init().
   */
  int __init dino_init(void)
  {
  	register_parisc_driver(&dino_driver);
  	return 0;
  }