pata_serverworks.c 13.1 KB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493
// SPDX-License-Identifier: GPL-2.0-only
/*
 * pata_serverworks.c 	- Serverworks PATA for new ATA layer
 *			  (C) 2005 Red Hat Inc
 *			  (C) 2010 Bartlomiej Zolnierkiewicz
 *
 * based upon
 *
 * serverworks.c
 *
 * Copyright (C) 1998-2000 Michel Aubry
 * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
 * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
 * Portions copyright (c) 2001 Sun Microsystems
 *
 *
 * RCC/ServerWorks IDE driver for Linux
 *
 *   OSB4: `Open South Bridge' IDE Interface (fn 1)
 *         supports UDMA mode 2 (33 MB/s)
 *
 *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
 *         all revisions support UDMA mode 4 (66 MB/s)
 *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
 *
 *         *** The CSB5 does not provide ANY register ***
 *         *** to detect 80-conductor cable presence. ***
 *
 *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
 *
 * Documentation:
 *	Available under NDA only. Errata info very hard to get.
 */

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME "pata_serverworks"
#define DRV_VERSION "0.4.3"

#define SVWKS_CSB5_REVISION_NEW	0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
#define SVWKS_CSB6_REVISION	0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */

/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
 * can overrun their FIFOs when used with the CSB5 */

static const char *csb_bad_ata100[] = {
	"ST320011A",
	"ST340016A",
	"ST360021A",
	"ST380021A",
	NULL
};

/**
 *	oem_cable	-	Dell/Sun serverworks cable detection
 *	@ap: ATA port to do cable detect
 *
 *	Dell PowerEdge and Sun Cobalt 'Alpine' hide the 40/80 pin select
 *	for their interfaces in the top two bits of the subsystem ID.
 */

static int oem_cable(struct ata_port *ap)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
		return ATA_CBL_PATA80;
	return ATA_CBL_PATA40;
}

struct sv_cable_table {
	int device;
	int subvendor;
	int (*cable_detect)(struct ata_port *ap);
};

static struct sv_cable_table cable_detect[] = {
	{ PCI_DEVICE_ID_SERVERWORKS_CSB5IDE,   PCI_VENDOR_ID_DELL, oem_cable },
	{ PCI_DEVICE_ID_SERVERWORKS_CSB6IDE,   PCI_VENDOR_ID_DELL, oem_cable },
	{ PCI_DEVICE_ID_SERVERWORKS_CSB5IDE,   PCI_VENDOR_ID_SUN,  oem_cable },
	{ PCI_DEVICE_ID_SERVERWORKS_OSB4IDE,   PCI_ANY_ID, ata_cable_40wire  },
	{ PCI_DEVICE_ID_SERVERWORKS_CSB5IDE,   PCI_ANY_ID, ata_cable_unknown },
	{ PCI_DEVICE_ID_SERVERWORKS_CSB6IDE,   PCI_ANY_ID, ata_cable_unknown },
	{ PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2,  PCI_ANY_ID, ata_cable_unknown },
	{ PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, ata_cable_unknown },
	{ }
};

/**
 *	serverworks_cable_detect	-	cable detection
 *	@ap: ATA port
 *
 *	Perform cable detection according to the device and subvendor
 *	identifications
 */

static int serverworks_cable_detect(struct ata_port *ap)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	struct sv_cable_table *cb = cable_detect;

	while(cb->device) {
		if (cb->device == pdev->device &&
		    (cb->subvendor == pdev->subsystem_vendor ||
		      cb->subvendor == PCI_ANY_ID)) {
			return cb->cable_detect(ap);
		}
		cb++;
	}

	BUG();
	return -1;	/* kill compiler warning */
}

/**
 *	serverworks_is_csb	-	Check for CSB or OSB
 *	@pdev: PCI device to check
 *
 *	Returns true if the device being checked is known to be a CSB
 *	series device.
 */

static u8 serverworks_is_csb(struct pci_dev *pdev)
{
	switch (pdev->device) {
		case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
		case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
		case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
		case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
			return 1;
		default:
			break;
	}
	return 0;
}

/**
 *	serverworks_osb4_filter	-	mode selection filter
 *	@adev: ATA device
 *	@mask: Mask of proposed modes
 *
 *	Filter the offered modes for the device to apply controller
 *	specific rules. OSB4 requires no UDMA for disks due to a FIFO
 *	bug we hit.
 */

static unsigned long serverworks_osb4_filter(struct ata_device *adev, unsigned long mask)
{
	if (adev->class == ATA_DEV_ATA)
		mask &= ~ATA_MASK_UDMA;
	return mask;
}


/**
 *	serverworks_csb_filter	-	mode selection filter
 *	@adev: ATA device
 *	@mask: Mask of proposed modes
 *
 *	Check the blacklist and disable UDMA5 if matched
 */

static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned long mask)
{
	const char *p;
	char model_num[ATA_ID_PROD_LEN + 1];
	int i;

	/* Disk, UDMA */
	if (adev->class != ATA_DEV_ATA)
		return mask;

	/* Actually do need to check */
	ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num));

	for (i = 0; (p = csb_bad_ata100[i]) != NULL; i++) {
		if (!strcmp(p, model_num))
			mask &= ~(0xE0 << ATA_SHIFT_UDMA);
	}
	return mask;
}

/**
 *	serverworks_set_piomode	-	set initial PIO mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Program the OSB4/CSB5 timing registers for PIO. The PIO register
 *	load is done as a simple lookup.
 */
static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
	int offset = 1 + 2 * ap->port_no - adev->devno;
	int devbits = (2 * ap->port_no + adev->devno) * 4;
	u16 csb5_pio;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	int pio = adev->pio_mode - XFER_PIO_0;

	pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]);

	/* The OSB4 just requires the timing but the CSB series want the
	   mode number as well */
	if (serverworks_is_csb(pdev)) {
		pci_read_config_word(pdev, 0x4A, &csb5_pio);
		csb5_pio &= ~(0x0F << devbits);
		pci_write_config_word(pdev, 0x4A, csb5_pio | (pio << devbits));
	}
}

/**
 *	serverworks_set_dmamode	-	set initial DMA mode data
 *	@ap: ATA interface
 *	@adev: ATA device
 *
 *	Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5
 *	chipset. The MWDMA mode values are pulled from a lookup table
 *	while the chipset uses mode number for UDMA.
 */

static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
	static const u8 dma_mode[] = { 0x77, 0x21, 0x20 };
	int offset = 1 + 2 * ap->port_no - adev->devno;
	int devbits = 2 * ap->port_no + adev->devno;
	u8 ultra;
	u8 ultra_cfg;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	pci_read_config_byte(pdev, 0x54, &ultra_cfg);
	pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra);
	ultra &= ~(0x0F << (adev->devno * 4));

	if (adev->dma_mode >= XFER_UDMA_0) {
		pci_write_config_byte(pdev, 0x44 + offset,  0x20);

		ultra |= (adev->dma_mode - XFER_UDMA_0)
					<< (adev->devno * 4);
		ultra_cfg |=  (1 << devbits);
	} else {
		pci_write_config_byte(pdev, 0x44 + offset,
			dma_mode[adev->dma_mode - XFER_MW_DMA_0]);
		ultra_cfg &= ~(1 << devbits);
	}
	pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra);
	pci_write_config_byte(pdev, 0x54, ultra_cfg);
}

static struct scsi_host_template serverworks_osb4_sht = {
	ATA_BMDMA_SHT(DRV_NAME),
	.sg_tablesize	= LIBATA_DUMB_MAX_PRD,
};

static struct scsi_host_template serverworks_csb_sht = {
	ATA_BMDMA_SHT(DRV_NAME),
};

static struct ata_port_operations serverworks_osb4_port_ops = {
	.inherits	= &ata_bmdma_port_ops,
	.qc_prep	= ata_bmdma_dumb_qc_prep,
	.cable_detect	= serverworks_cable_detect,
	.mode_filter	= serverworks_osb4_filter,
	.set_piomode	= serverworks_set_piomode,
	.set_dmamode	= serverworks_set_dmamode,
};

static struct ata_port_operations serverworks_csb_port_ops = {
	.inherits	= &serverworks_osb4_port_ops,
	.qc_prep	= ata_bmdma_qc_prep,
	.mode_filter	= serverworks_csb_filter,
};

static int serverworks_fixup_osb4(struct pci_dev *pdev)
{
	u32 reg;
	struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
		  PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
	if (isa_dev) {
		pci_read_config_dword(isa_dev, 0x64, &reg);
		reg &= ~0x00002000; /* disable 600ns interrupt mask */
		if (!(reg & 0x00004000))
			printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n");
		reg |=  0x00004000; /* enable UDMA/33 support */
		pci_write_config_dword(isa_dev, 0x64, reg);
		pci_dev_put(isa_dev);
		return 0;
	}
	printk(KERN_WARNING DRV_NAME ": Unable to find bridge.\n");
	return -ENODEV;
}

static int serverworks_fixup_csb(struct pci_dev *pdev)
{
	u8 btr;

	/* Third Channel Test */
	if (!(PCI_FUNC(pdev->devfn) & 1)) {
		struct pci_dev * findev = NULL;
		u32 reg4c = 0;
		findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
			PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
		if (findev) {
			pci_read_config_dword(findev, 0x4C, &reg4c);
			reg4c &= ~0x000007FF;
			reg4c |=  0x00000040;
			reg4c |=  0x00000020;
			pci_write_config_dword(findev, 0x4C, reg4c);
			pci_dev_put(findev);
		}
	} else {
		struct pci_dev * findev = NULL;
		u8 reg41 = 0;

		findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
				PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
		if (findev) {
			pci_read_config_byte(findev, 0x41, &reg41);
			reg41 &= ~0x40;
			pci_write_config_byte(findev, 0x41, reg41);
			pci_dev_put(findev);
		}
	}
	/* setup the UDMA Control register
	 *
	 * 1. clear bit 6 to enable DMA
	 * 2. enable DMA modes with bits 0-1
	 * 	00 : legacy
	 * 	01 : udma2
	 * 	10 : udma2/udma4
	 * 	11 : udma2/udma4/udma5
	 */
	pci_read_config_byte(pdev, 0x5A, &btr);
	btr &= ~0x40;
	if (!(PCI_FUNC(pdev->devfn) & 1))
		btr |= 0x2;
	else
		btr |= (pdev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
	pci_write_config_byte(pdev, 0x5A, btr);

	return btr;
}

static void serverworks_fixup_ht1000(struct pci_dev *pdev)
{
	u8 btr;
	/* Setup HT1000 SouthBridge Controller - Single Channel Only */
	pci_read_config_byte(pdev, 0x5A, &btr);
	btr &= ~0x40;
	btr |= 0x3;
	pci_write_config_byte(pdev, 0x5A, btr);
}

static int serverworks_fixup(struct pci_dev *pdev)
{
	int rc = 0;

	/* Force master latency timer to 64 PCI clocks */
	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);

	switch (pdev->device) {
	case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
		rc = serverworks_fixup_osb4(pdev);
		break;
	case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
		ata_pci_bmdma_clear_simplex(pdev);
		/* fall through */
	case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
	case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
		rc = serverworks_fixup_csb(pdev);
		break;
	case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
		serverworks_fixup_ht1000(pdev);
		break;
	}

	return rc;
}

static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
	static const struct ata_port_info info[4] = {
		{ /* OSB4 */
			.flags = ATA_FLAG_SLAVE_POSS,
			.pio_mask = ATA_PIO4,
			.mwdma_mask = ATA_MWDMA2,
			.udma_mask = ATA_UDMA2,
			.port_ops = &serverworks_osb4_port_ops
		}, { /* OSB4 no UDMA */
			.flags = ATA_FLAG_SLAVE_POSS,
			.pio_mask = ATA_PIO4,
			.mwdma_mask = ATA_MWDMA2,
			/* No UDMA */
			.port_ops = &serverworks_osb4_port_ops
		}, { /* CSB5 */
			.flags = ATA_FLAG_SLAVE_POSS,
			.pio_mask = ATA_PIO4,
			.mwdma_mask = ATA_MWDMA2,
			.udma_mask = ATA_UDMA4,
			.port_ops = &serverworks_csb_port_ops
		}, { /* CSB5 - later revisions*/
			.flags = ATA_FLAG_SLAVE_POSS,
			.pio_mask = ATA_PIO4,
			.mwdma_mask = ATA_MWDMA2,
			.udma_mask = ATA_UDMA5,
			.port_ops = &serverworks_csb_port_ops
		}
	};
	const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
	struct scsi_host_template *sht = &serverworks_csb_sht;
	int rc;

	rc = pcim_enable_device(pdev);
	if (rc)
		return rc;

	rc = serverworks_fixup(pdev);

	/* OSB4 : South Bridge and IDE */
	if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
		/* Select non UDMA capable OSB4 if we can't do fixups */
		if (rc < 0)
			ppi[0] = &info[1];
		sht = &serverworks_osb4_sht;
	}
	/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
	else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
		 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
		 (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {

		 /* If the returned btr is the newer revision then
		    select the right info block */
		 if (rc == 3)
		 	ppi[0] = &info[3];

		/* Is this the 3rd channel CSB6 IDE ? */
		if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
			ppi[1] = &ata_dummy_port_info;
	}

	return ata_pci_bmdma_init_one(pdev, ppi, sht, NULL, 0);
}

#ifdef CONFIG_PM_SLEEP
static int serverworks_reinit_one(struct pci_dev *pdev)
{
	struct ata_host *host = pci_get_drvdata(pdev);
	int rc;

	rc = ata_pci_device_do_resume(pdev);
	if (rc)
		return rc;

	(void)serverworks_fixup(pdev);

	ata_host_resume(host);
	return 0;
}
#endif

static const struct pci_device_id serverworks[] = {
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},

	{ },
};

static struct pci_driver serverworks_pci_driver = {
	.name 		= DRV_NAME,
	.id_table	= serverworks,
	.probe 		= serverworks_init_one,
	.remove		= ata_pci_remove_one,
#ifdef CONFIG_PM_SLEEP
	.suspend	= ata_pci_device_suspend,
	.resume		= serverworks_reinit_one,
#endif
};

module_pci_driver(serverworks_pci_driver);

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, serverworks);
MODULE_VERSION(DRV_VERSION);