fdomain.c 55.8 KB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 1491 1492 1493 1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506 1507 1508 1509 1510 1511 1512 1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561 1562 1563 1564 1565 1566 1567 1568 1569 1570 1571 1572 1573 1574 1575 1576 1577 1578 1579 1580 1581 1582 1583 1584 1585 1586 1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599 1600 1601 1602 1603 1604 1605 1606 1607 1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626 1627 1628 1629 1630 1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641 1642 1643 1644 1645 1646 1647 1648 1649 1650 1651 1652 1653 1654 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693 1694 1695 1696 1697 1698 1699 1700 1701 1702 1703 1704 1705 1706 1707 1708 1709 1710 1711 1712 1713 1714 1715 1716 1717 1718 1719 1720 1721 1722 1723 1724 1725 1726 1727 1728 1729 1730 1731 1732 1733 1734 1735 1736 1737 1738 1739 1740 1741 1742 1743 1744 1745 1746 1747 1748 1749 1750 1751 1752 1753 1754 1755 1756 1757 1758 1759 1760 1761 1762 1763 1764 1765 1766 1767 1768 1769 1770 1771 1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783
/* fdomain.c -- Future Domain TMC-16x0 SCSI driver
 * Created: Sun May  3 18:53:19 1992 by faith@cs.unc.edu
 * Revised: Mon Dec 28 21:59:02 1998 by faith@acm.org
 * Author: Rickard E. Faith, faith@cs.unc.edu
 * Copyright 1992-1996, 1998 Rickard E. Faith (faith@acm.org)
 * Shared IRQ supported added 7/7/2001  Alan Cox <alan@lxorguk.ukuu.org.uk>

 * This program is free software; you can redistribute it and/or modify it
 * under the terms of the GNU General Public License as published by the
 * Free Software Foundation; either version 2, or (at your option) any
 * later version.

 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.

 * You should have received a copy of the GNU General Public License along
 * with this program; if not, write to the Free Software Foundation, Inc.,
 * 675 Mass Ave, Cambridge, MA 02139, USA.

 **************************************************************************

 SUMMARY:

 Future Domain BIOS versions supported for autodetect:
    2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61
 Chips are supported:
    TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70
 Boards supported:
    Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX
    Future Domain TMC-3260 (PCI)
    Quantum ISA-200S, ISA-250MG
    Adaptec AHA-2920A (PCI) [BUT *NOT* AHA-2920C -- use aic7xxx instead]
    IBM ?
 LILO/INSMOD command-line options:
    fdomain=<PORT_BASE>,<IRQ>[,<ADAPTER_ID>]


    
 NOTE:

 The Adaptec AHA-2920C has an Adaptec AIC-7850 chip on it.
 Use the aic7xxx driver for this board.
       
 The Adaptec AHA-2920A has a Future Domain chip on it, so this is the right
 driver for that card.  Unfortunately, the boxes will probably just say
 "2920", so you'll have to look on the card for a Future Domain logo, or a
 letter after the 2920.

 
 
 THANKS:

 Thanks to Adaptec for providing PCI boards for testing.  This finally
 enabled me to test the PCI detection and correct it for PCI boards that do
 not have a BIOS at a standard ISA location.  For PCI boards, LILO/INSMOD
 command-line options should no longer be needed.  --RF 18Nov98


 
 DESCRIPTION:
 
 This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680
 TMC-1650/1670, and TMC-3260 SCSI host adapters.  The 1650 and 1670 have a
 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin
 high-density external connector.  The 1670 and 1680 have floppy disk
 controllers built in.  The TMC-3260 is a PCI bus card.

 Future Domain's older boards are based on the TMC-1800 chip, and this
 driver was originally written for a TMC-1680 board with the TMC-1800 chip.
 More recently, boards are being produced with the TMC-18C50 and TMC-18C30
 chips.  The latest and greatest board may not work with this driver.  If
 you have to patch this driver so that it will recognize your board's BIOS
 signature, then the driver may fail to function after the board is
 detected.

 Please note that the drive ordering that Future Domain implemented in BIOS
 versions 3.4 and 3.5 is the opposite of the order (currently) used by the
 rest of the SCSI industry.  If you have BIOS version 3.4 or 3.5, and have
 more than one drive, then the drive ordering will be the reverse of that
 which you see under DOS.  For example, under DOS SCSI ID 0 will be D: and
 SCSI ID 1 will be C: (the boot device).  Under Linux, SCSI ID 0 will be
 /dev/sda and SCSI ID 1 will be /dev/sdb.  The Linux ordering is consistent
 with that provided by all the other SCSI drivers for Linux.  If you want
 this changed, you will probably have to patch the higher level SCSI code.
 If you do so, please send me patches that are protected by #ifdefs.

 If you have a TMC-8xx or TMC-9xx board, then this is not the driver for
 your board.  Please refer to the Seagate driver for more information and
 possible support.

 
 
 HISTORY:

 Linux       Driver      Driver
 Version     Version     Date         Support/Notes

             0.0          3 May 1992  V2.0 BIOS; 1800 chip
 0.97        1.9         28 Jul 1992
 0.98.6      3.1         27 Nov 1992
 0.99        3.2          9 Dec 1992

 0.99.3      3.3         10 Jan 1993  V3.0 BIOS
 0.99.5      3.5         18 Feb 1993
 0.99.10     3.6         15 May 1993  V3.2 BIOS; 18C50 chip
 0.99.11     3.17         3 Jul 1993  (now under RCS)
 0.99.12     3.18        13 Aug 1993
 0.99.14     5.6         31 Oct 1993  (reselection code removed)

 0.99.15     5.9         23 Jan 1994  V3.4 BIOS (preliminary)
 1.0.8/1.1.1 5.15         1 Apr 1994  V3.4 BIOS; 18C30 chip (preliminary)
 1.0.9/1.1.3 5.16         7 Apr 1994  V3.4 BIOS; 18C30 chip
 1.1.38      5.18        30 Jul 1994  36C70 chip (PCI version of 18C30)
 1.1.62      5.20         2 Nov 1994  V3.5 BIOS
 1.1.73      5.22         7 Dec 1994  Quantum ISA-200S board; V2.0 BIOS

 1.1.82      5.26        14 Jan 1995  V3.5 BIOS; TMC-1610M/MER/MEX board
 1.2.10      5.28         5 Jun 1995  Quantum ISA-250MG board; V2.0, V2.01 BIOS
 1.3.4       5.31        23 Jun 1995  PCI BIOS-32 detection (preliminary)
 1.3.7       5.33         4 Jul 1995  PCI BIOS-32 detection
 1.3.28      5.36        17 Sep 1995  V3.61 BIOS; LILO command-line support
 1.3.34      5.39        12 Oct 1995  V3.60 BIOS; /proc
 1.3.72      5.39         8 Feb 1996  Adaptec AHA-2920 board
 1.3.85      5.41         4 Apr 1996
 2.0.12      5.44         8 Aug 1996  Use ID 7 for all PCI cards
 2.1.1       5.45         2 Oct 1996  Update ROM accesses for 2.1.x
 2.1.97      5.46	 23 Apr 1998  Rewritten PCI detection routines [mj]
 2.1.11x     5.47	  9 Aug 1998  Touched for 8 SCSI disk majors support
             5.48        18 Nov 1998  BIOS no longer needed for PCI detection
 2.2.0       5.50        28 Dec 1998  Support insmod parameters
 

 REFERENCES USED:

 "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation,
 1990.

 "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain
 Corporation, January 1992.

 "LXT SCSI Products: Specifications and OEM Technical Manual (Revision
 B/September 1991)", Maxtor Corporation, 1991.

 "7213S product Manual (Revision P3)", Maxtor Corporation, 1992.

 "Draft Proposed American National Standard: Small Computer System
 Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109,
 revision 10h, October 17, 1991)

 Private communications, Drew Eckhardt (drew@cs.colorado.edu) and Eric
 Youngdale (ericy@cais.com), 1992.

 Private communication, Tuong Le (Future Domain Engineering department),
 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and
 TMC-18C30 detection.)

 Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page
 60 (2.39: Disk Partition Table Layout).

 "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page
 6-1.


 
 NOTES ON REFERENCES:

 The Maxtor manuals were free.  Maxtor telephone technical support is
 great!

 The Future Domain manuals were $25 and $35.  They document the chip, not
 the TMC-16x0 boards, so some information I had to guess at.  In 1992,
 Future Domain sold DOS BIOS source for $250 and the UN*X driver source was
 $750, but these required a non-disclosure agreement, so even if I could
 have afforded them, they would *not* have been useful for writing this
 publicly distributable driver.  Future Domain technical support has
 provided some information on the phone and have sent a few useful FAXs.
 They have been much more helpful since they started to recognize that the
 word "Linux" refers to an operating system :-).

 

 ALPHA TESTERS:

 There are many other alpha testers that come and go as the driver
 develops.  The people listed here were most helpful in times of greatest
 need (mostly early on -- I've probably left out a few worthy people in
 more recent times):

 Todd Carrico (todd@wutc.wustl.edu), Dan Poirier (poirier@cs.unc.edu ), Ken
 Corey (kenc@sol.acs.unt.edu), C. de Bruin (bruin@bruin@sterbbs.nl), Sakari
 Aaltonen (sakaria@vipunen.hit.fi), John Rice (rice@xanth.cs.odu.edu), Brad
 Yearwood (brad@optilink.com), and Ray Toy (toy@soho.crd.ge.com).

 Special thanks to Tien-Wan Yang (twyang@cs.uh.edu), who graciously lent me
 his 18C50-based card for debugging.  He is the sole reason that this
 driver works with the 18C50 chip.

 Thanks to Dave Newman (dnewman@crl.com) for providing initial patches for
 the version 3.4 BIOS.

 Thanks to James T. McKinley (mckinley@msupa.pa.msu.edu) for providing
 patches that support the TMC-3260, a PCI bus card with the 36C70 chip.
 The 36C70 chip appears to be "completely compatible" with the 18C30 chip.

 Thanks to Eric Kasten (tigger@petroglyph.cl.msu.edu) for providing the
 patch for the version 3.5 BIOS.

 Thanks for Stephen Henson (shenson@nyx10.cs.du.edu) for providing the
 patch for the Quantum ISA-200S SCSI adapter.
 
 Thanks to Adam Bowen for the signature to the 1610M/MER/MEX scsi cards, to
 Martin Andrews (andrewm@ccfadm.eeg.ccf.org) for the signature to some
 random TMC-1680 repackaged by IBM; and to Mintak Ng (mintak@panix.com) for
 the version 3.61 BIOS signature.

 Thanks for Mark Singer (elf@netcom.com) and Richard Simpson
 (rsimpson@ewrcsdra.demon.co.uk) for more Quantum signatures and detective
 work on the Quantum RAM layout.

 Special thanks to James T. McKinley (mckinley@msupa.pa.msu.edu) for
 providing patches for proper PCI BIOS32-mediated detection of the TMC-3260
 card (a PCI bus card with the 36C70 chip).  Please send James PCI-related
 bug reports.

 Thanks to Tom Cavin (tec@usa1.com) for preliminary command-line option
 patches.

 New PCI detection code written by Martin Mares <mj@atrey.karlin.mff.cuni.cz>

 Insmod parameter code based on patches from Daniel Graham
 <graham@balance.uoregon.edu>. 
 
 All of the alpha testers deserve much thanks.



 NOTES ON USER DEFINABLE OPTIONS:

 DEBUG: This turns on the printing of various debug information.

 ENABLE_PARITY: This turns on SCSI parity checking.  With the current
 driver, all attached devices must support SCSI parity.  If none of your
 devices support parity, then you can probably get the driver to work by
 turning this option off.  I have no way of testing this, however, and it
 would appear that no one ever uses this option.

 FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the
 18C30 chip have a 2k cache).  When this many 512 byte blocks are filled by
 the SCSI device, an interrupt will be raised.  Therefore, this could be as
 low as 0, or as high as 16.  Note, however, that values which are too high
 or too low seem to prevent any interrupts from occurring, and thereby lock
 up the machine.  I have found that 2 is a good number, but throughput may
 be increased by changing this value to values which are close to 2.
 Please let me know if you try any different values.

 RESELECTION: This is no longer an option, since I gave up trying to
 implement it in version 4.x of this driver.  It did not improve
 performance at all and made the driver unstable (because I never found one
 of the two race conditions which were introduced by the multiple
 outstanding command code).  The instability seems a very high price to pay
 just so that you don't have to wait for the tape to rewind.  If you want
 this feature implemented, send me patches.  I'll be happy to send a copy
 of my (broken) driver to anyone who would like to see a copy.

 **************************************************************************/

#include <linux/module.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/blkdev.h>
#include <linux/spinlock.h>
#include <linux/errno.h>
#include <linux/string.h>
#include <linux/ioport.h>
#include <linux/proc_fs.h>
#include <linux/pci.h>
#include <linux/stat.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/slab.h>
#include <scsi/scsicam.h>


#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_ioctl.h>
#include "fdomain.h"

#ifndef PCMCIA
MODULE_AUTHOR("Rickard E. Faith");
MODULE_DESCRIPTION("Future domain SCSI driver");
MODULE_LICENSE("GPL");
#endif

  
#define VERSION          "$Revision: 5.51 $"

/* START OF USER DEFINABLE OPTIONS */

#define DEBUG            0	/* Enable debugging output */
#define ENABLE_PARITY    1	/* Enable SCSI Parity */
#define FIFO_COUNT       2	/* Number of 512 byte blocks before INTR */

/* END OF USER DEFINABLE OPTIONS */

#if DEBUG
#define EVERY_ACCESS     0	/* Write a line on every scsi access */
#define ERRORS_ONLY      1	/* Only write a line if there is an error */
#define DEBUG_DETECT     0	/* Debug fdomain_16x0_detect() */
#define DEBUG_MESSAGES   1	/* Debug MESSAGE IN phase */
#define DEBUG_ABORT      1	/* Debug abort() routine */
#define DEBUG_RESET      1	/* Debug reset() routine */
#define DEBUG_RACE       1      /* Debug interrupt-driven race condition */
#else
#define EVERY_ACCESS     0	/* LEAVE THESE ALONE--CHANGE THE ONES ABOVE */
#define ERRORS_ONLY      0
#define DEBUG_DETECT     0
#define DEBUG_MESSAGES   0
#define DEBUG_ABORT      0
#define DEBUG_RESET      0
#define DEBUG_RACE       0
#endif

/* Errors are reported on the line, so we don't need to report them again */
#if EVERY_ACCESS
#undef ERRORS_ONLY
#define ERRORS_ONLY      0
#endif

#if ENABLE_PARITY
#define PARITY_MASK      0x08
#else
#define PARITY_MASK      0x00
#endif

enum chip_type {
   unknown          = 0x00,
   tmc1800          = 0x01,
   tmc18c50         = 0x02,
   tmc18c30         = 0x03,
};

enum {
   in_arbitration   = 0x02,
   in_selection     = 0x04,
   in_other         = 0x08,
   disconnect       = 0x10,
   aborted          = 0x20,
   sent_ident       = 0x40,
};

enum in_port_type {
   Read_SCSI_Data   =  0,
   SCSI_Status      =  1,
   TMC_Status       =  2,
   FIFO_Status      =  3,	/* tmc18c50/tmc18c30 only */
   Interrupt_Cond   =  4,	/* tmc18c50/tmc18c30 only */
   LSB_ID_Code      =  5,
   MSB_ID_Code      =  6,
   Read_Loopback    =  7,
   SCSI_Data_NoACK  =  8,
   Interrupt_Status =  9,
   Configuration1   = 10,
   Configuration2   = 11,	/* tmc18c50/tmc18c30 only */
   Read_FIFO        = 12,
   FIFO_Data_Count  = 14
};

enum out_port_type {
   Write_SCSI_Data  =  0,
   SCSI_Cntl        =  1,
   Interrupt_Cntl   =  2,
   SCSI_Mode_Cntl   =  3,
   TMC_Cntl         =  4,
   Memory_Cntl      =  5,	/* tmc18c50/tmc18c30 only */
   Write_Loopback   =  7,
   IO_Control       = 11,	/* tmc18c30 only */
   Write_FIFO       = 12
};

/* .bss will zero all the static variables below */
static int               port_base;
static unsigned long     bios_base;
static void __iomem *    bios_mem;
static int               bios_major;
static int               bios_minor;
static int               PCI_bus;
#ifdef CONFIG_PCI
static struct pci_dev	*PCI_dev;
#endif
static int               Quantum;	/* Quantum board variant */
static int               interrupt_level;
static volatile int      in_command;
static struct scsi_cmnd  *current_SC;
static enum chip_type    chip              = unknown;
static int               adapter_mask;
static int               this_id;
static int               setup_called;

#if DEBUG_RACE
static volatile int      in_interrupt_flag;
#endif

static int               FIFO_Size = 0x2000; /* 8k FIFO for
						pre-tmc18c30 chips */

static irqreturn_t       do_fdomain_16x0_intr( int irq, void *dev_id );
/* Allow insmod parameters to be like LILO parameters.  For example:
   insmod fdomain fdomain=0x140,11 */
static char * fdomain = NULL;
module_param(fdomain, charp, 0);

#ifndef PCMCIA

static unsigned long addresses[] = {
   0xc8000,
   0xca000,
   0xce000,
   0xde000,
   0xcc000,		/* Extra addresses for PCI boards */
   0xd0000,
   0xe0000,
};
#define ADDRESS_COUNT ARRAY_SIZE(addresses)

static unsigned short ports[] = { 0x140, 0x150, 0x160, 0x170 };
#define PORT_COUNT ARRAY_SIZE(ports)

static unsigned short ints[] = { 3, 5, 10, 11, 12, 14, 15, 0 };

#endif /* !PCMCIA */

/*

  READ THIS BEFORE YOU ADD A SIGNATURE!

  READING THIS SHORT NOTE CAN SAVE YOU LOTS OF TIME!

  READ EVERY WORD, ESPECIALLY THE WORD *NOT*

  This driver works *ONLY* for Future Domain cards using the TMC-1800,
  TMC-18C50, or TMC-18C30 chip.  This includes models TMC-1650, 1660, 1670,
  and 1680.  These are all 16-bit cards.

  The following BIOS signature signatures are for boards which do *NOT*
  work with this driver (these TMC-8xx and TMC-9xx boards may work with the
  Seagate driver):

  FUTURE DOMAIN CORP. (C) 1986-1988 V4.0I 03/16/88
  FUTURE DOMAIN CORP. (C) 1986-1989 V5.0C2/14/89
  FUTURE DOMAIN CORP. (C) 1986-1989 V6.0A7/28/89
  FUTURE DOMAIN CORP. (C) 1986-1990 V6.0105/31/90
  FUTURE DOMAIN CORP. (C) 1986-1990 V6.0209/18/90
  FUTURE DOMAIN CORP. (C) 1986-1990 V7.009/18/90
  FUTURE DOMAIN CORP. (C) 1992 V8.00.004/02/92

  (The cards which do *NOT* work are all 8-bit cards -- although some of
  them have a 16-bit form-factor, the upper 8-bits are used only for IRQs
  and are *NOT* used for data.  You can tell the difference by following
  the tracings on the circuit board -- if only the IRQ lines are involved,
  you have a "8-bit" card, and should *NOT* use this driver.)

*/

#ifndef PCMCIA

static struct signature {
   const char *signature;
   int  sig_offset;
   int  sig_length;
   int  major_bios_version;
   int  minor_bios_version;
   int  flag; /* 1 == PCI_bus, 2 == ISA_200S, 3 == ISA_250MG, 4 == ISA_200S */
} signatures[] = {
   /*          1         2         3         4         5         6 */
   /* 123456789012345678901234567890123456789012345678901234567890 */
   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.07/28/89",  5, 50,  2,  0, 0 },
   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V1.07/28/89",  5, 50,  2,  0, 0 },
   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.07/28/89", 72, 50,  2,  0, 2 },
   { "FUTURE DOMAIN CORP. (C) 1986-1990 1800-V2.0",        73, 43,  2,  0, 3 },
   { "FUTURE DOMAIN CORP. (C) 1991 1800-V2.0.",            72, 39,  2,  0, 4 },
   { "FUTURE DOMAIN CORP. (C) 1992 V3.00.004/02/92",        5, 44,  3,  0, 0 },
   { "FUTURE DOMAIN TMC-18XX (C) 1993 V3.203/12/93",        5, 44,  3,  2, 0 },
   { "IBM F1 P2 BIOS v1.0104/29/93",                        5, 28,  3, -1, 0 },
   { "Future Domain Corp. V1.0008/18/93",                   5, 33,  3,  4, 0 },
   { "Future Domain Corp. V1.0008/18/93",                  26, 33,  3,  4, 1 },
   { "Adaptec AHA-2920 PCI-SCSI Card",                     42, 31,  3, -1, 1 },
   { "IBM F1 P264/32",                                      5, 14,  3, -1, 1 },
				/* This next signature may not be a 3.5 bios */
   { "Future Domain Corp. V2.0108/18/93",                   5, 33,  3,  5, 0 },
   { "FUTURE DOMAIN CORP.  V3.5008/18/93",                  5, 34,  3,  5, 0 },
   { "FUTURE DOMAIN 18c30/18c50/1800 (C) 1994 V3.5",        5, 44,  3,  5, 0 },
   { "FUTURE DOMAIN CORP.  V3.6008/18/93",                  5, 34,  3,  6, 0 },
   { "FUTURE DOMAIN CORP.  V3.6108/18/93",                  5, 34,  3,  6, 0 },
   { "FUTURE DOMAIN TMC-18XX",                              5, 22, -1, -1, 0 },

   /* READ NOTICE ABOVE *BEFORE* YOU WASTE YOUR TIME ADDING A SIGNATURE
    Also, fix the disk geometry code for your signature and send your
    changes for faith@cs.unc.edu.  Above all, do *NOT* change any old
    signatures!

    Note that the last line will match a "generic" 18XX bios.  Because
    Future Domain has changed the host SCSI ID and/or the location of the
    geometry information in the on-board RAM area for each of the first
    three BIOS's, it is still important to enter a fully qualified
    signature in the table for any new BIOS's (after the host SCSI ID and
    geometry location are verified). */
};

#define SIGNATURE_COUNT ARRAY_SIZE(signatures)

#endif /* !PCMCIA */

static void print_banner( struct Scsi_Host *shpnt )
{
   if (!shpnt) return;		/* This won't ever happen */

   if (bios_major < 0 && bios_minor < 0) {
      printk(KERN_INFO "scsi%d: <fdomain> No BIOS; using scsi id %d\n",
	      shpnt->host_no, shpnt->this_id);
   } else {
      printk(KERN_INFO "scsi%d: <fdomain> BIOS version ", shpnt->host_no);

      if (bios_major >= 0) printk("%d.", bios_major);
      else                 printk("?.");

      if (bios_minor >= 0) printk("%d", bios_minor);
      else                 printk("?.");

      printk( " at 0x%lx using scsi id %d\n",
	      bios_base, shpnt->this_id );
   }

				/* If this driver works for later FD PCI
				   boards, we will have to modify banner
				   for additional PCI cards, but for now if
				   it's PCI it's a TMC-3260 - JTM */
   printk(KERN_INFO "scsi%d: <fdomain> %s chip at 0x%x irq ",
	   shpnt->host_no,
	   chip == tmc1800 ? "TMC-1800" : (chip == tmc18c50 ? "TMC-18C50" : (chip == tmc18c30 ? (PCI_bus ? "TMC-36C70 (PCI bus)" : "TMC-18C30") : "Unknown")),
	   port_base);

   if (interrupt_level)
   	printk("%d", interrupt_level);
   else
        printk("<none>");

   printk( "\n" );
}

int fdomain_setup(char *str)
{
	int ints[4];

	(void)get_options(str, ARRAY_SIZE(ints), ints);

	if (setup_called++ || ints[0] < 2 || ints[0] > 3) {
		printk(KERN_INFO "scsi: <fdomain> Usage: fdomain=<PORT_BASE>,<IRQ>[,<ADAPTER_ID>]\n");
		printk(KERN_ERR "scsi: <fdomain> Bad LILO/INSMOD parameters?\n");
		return 0;
	}

	port_base       = ints[0] >= 1 ? ints[1] : 0;
	interrupt_level = ints[0] >= 2 ? ints[2] : 0;
	this_id         = ints[0] >= 3 ? ints[3] : 0;
   
	bios_major = bios_minor = -1; /* Use geometry for BIOS version >= 3.4 */
	++setup_called;
	return 1;
}

__setup("fdomain=", fdomain_setup);


static void do_pause(unsigned amount)	/* Pause for amount*10 milliseconds */
{
	mdelay(10*amount);
}

static inline void fdomain_make_bus_idle( void )
{
   outb(0, port_base + SCSI_Cntl);
   outb(0, port_base + SCSI_Mode_Cntl);
   if (chip == tmc18c50 || chip == tmc18c30)
	 outb(0x21 | PARITY_MASK, port_base + TMC_Cntl); /* Clear forced intr. */
   else
	 outb(0x01 | PARITY_MASK, port_base + TMC_Cntl);
}

static int fdomain_is_valid_port( int port )
{
#if DEBUG_DETECT 
   printk( " (%x%x),",
	   inb( port + MSB_ID_Code ), inb( port + LSB_ID_Code ) );
#endif

   /* The MCA ID is a unique id for each MCA compatible board.  We
      are using ISA boards, but Future Domain provides the MCA ID
      anyway.  We can use this ID to ensure that this is a Future
      Domain TMC-1660/TMC-1680.
    */

   if (inb( port + LSB_ID_Code ) != 0xe9) { /* test for 0x6127 id */
      if (inb( port + LSB_ID_Code ) != 0x27) return 0;
      if (inb( port + MSB_ID_Code ) != 0x61) return 0;
      chip = tmc1800;
   } else {				    /* test for 0xe960 id */
      if (inb( port + MSB_ID_Code ) != 0x60) return 0;
      chip = tmc18c50;

				/* Try to toggle 32-bit mode.  This only
				   works on an 18c30 chip.  (User reports
				   say this works, so we should switch to
				   it in the near future.) */

      outb( 0x80, port + IO_Control );
      if ((inb( port + Configuration2 ) & 0x80) == 0x80) {
	 outb( 0x00, port + IO_Control );
	 if ((inb( port + Configuration2 ) & 0x80) == 0x00) {
	    chip = tmc18c30;
	    FIFO_Size = 0x800;	/* 2k FIFO */
	 }
      }
				/* If that failed, we are an 18c50. */
   }

   return 1;
}

static int fdomain_test_loopback( void )
{
   int i;
   int result;

   for (i = 0; i < 255; i++) {
      outb( i, port_base + Write_Loopback );
      result = inb( port_base + Read_Loopback );
      if (i != result)
	    return 1;
   }
   return 0;
}

#ifndef PCMCIA

/* fdomain_get_irq assumes that we have a valid MCA ID for a
   TMC-1660/TMC-1680 Future Domain board.  Now, check to be sure the
   bios_base matches these ports.  If someone was unlucky enough to have
   purchased more than one Future Domain board, then they will have to
   modify this code, as we only detect one board here.  [The one with the
   lowest bios_base.]

   Note that this routine is only used for systems without a PCI BIOS32
   (e.g., ISA bus).  For PCI bus systems, this routine will likely fail
   unless one of the IRQs listed in the ints array is used by the board.
   Sometimes it is possible to use the computer's BIOS setup screen to
   configure a PCI system so that one of these IRQs will be used by the
   Future Domain card. */

static int fdomain_get_irq( int base )
{
   int options = inb(base + Configuration1);

#if DEBUG_DETECT
   printk("scsi: <fdomain> Options = %x\n", options);
#endif
 
   /* Check for board with lowest bios_base --
      this isn't valid for the 18c30 or for
      boards on the PCI bus, so just assume we
      have the right board. */

   if (chip != tmc18c30 && !PCI_bus && addresses[(options & 0xc0) >> 6 ] != bios_base)
   	return 0;
   return ints[(options & 0x0e) >> 1];
}

static int fdomain_isa_detect( int *irq, int *iobase )
{
   int i, j;
   int base = 0xdeadbeef;
   int flag = 0;

#if DEBUG_DETECT
   printk( "scsi: <fdomain> fdomain_isa_detect:" );
#endif

   for (i = 0; i < ADDRESS_COUNT; i++) {
      void __iomem *p = ioremap(addresses[i], 0x2000);
      if (!p)
	continue;
#if DEBUG_DETECT
      printk( " %lx(%lx),", addresses[i], bios_base );
#endif
      for (j = 0; j < SIGNATURE_COUNT; j++) {
	 if (check_signature(p + signatures[j].sig_offset,
			     signatures[j].signature,
			     signatures[j].sig_length )) {
	    bios_major = signatures[j].major_bios_version;
	    bios_minor = signatures[j].minor_bios_version;
	    PCI_bus    = (signatures[j].flag == 1);
	    Quantum    = (signatures[j].flag > 1) ? signatures[j].flag : 0;
	    bios_base  = addresses[i];
	    bios_mem   = p;
	    goto found;
	 }
      }
      iounmap(p);
   }
 
found:
   if (bios_major == 2) {
      /* The TMC-1660/TMC-1680 has a RAM area just after the BIOS ROM.
	 Assuming the ROM is enabled (otherwise we wouldn't have been
	 able to read the ROM signature :-), then the ROM sets up the
	 RAM area with some magic numbers, such as a list of port
	 base addresses and a list of the disk "geometry" reported to
	 DOS (this geometry has nothing to do with physical geometry).
       */

      switch (Quantum) {
      case 2:			/* ISA_200S */
      case 3:			/* ISA_250MG */
	 base = readb(bios_mem + 0x1fa2) + (readb(bios_mem + 0x1fa3) << 8);
	 break;
      case 4:			/* ISA_200S (another one) */
	 base = readb(bios_mem + 0x1fa3) + (readb(bios_mem + 0x1fa4) << 8);
	 break;
      default:
	 base = readb(bios_mem + 0x1fcc) + (readb(bios_mem + 0x1fcd) << 8);
	 break;
      }
   
#if DEBUG_DETECT
      printk( " %x,", base );
#endif

      for (i = 0; i < PORT_COUNT; i++) {
	if (base == ports[i]) {
		if (!request_region(base, 0x10, "fdomain"))
			break;
		if (!fdomain_is_valid_port(base)) {
			release_region(base, 0x10);
			break;
		}
		*irq    = fdomain_get_irq( base );
		*iobase = base;
		return 1;
	}
      }

      /* This is a bad sign.  It usually means that someone patched the
	 BIOS signature list (the signatures variable) to contain a BIOS
	 signature for a board *OTHER THAN* the TMC-1660/TMC-1680. */
      
#if DEBUG_DETECT
      printk( " RAM FAILED, " );
#endif
   }

   /* Anyway, the alternative to finding the address in the RAM is to just
      search through every possible port address for one that is attached
      to the Future Domain card.  Don't panic, though, about reading all
      these random port addresses -- there are rumors that the Future
      Domain BIOS does something very similar.

      Do not, however, check ports which the kernel knows are being used by
      another driver. */

   for (i = 0; i < PORT_COUNT; i++) {
      base = ports[i];
      if (!request_region(base, 0x10, "fdomain")) {
#if DEBUG_DETECT
	 printk( " (%x inuse),", base );
#endif
	 continue;
      }
#if DEBUG_DETECT
      printk( " %x,", base );
#endif
      flag = fdomain_is_valid_port(base);
      if (flag)
	break;
      release_region(base, 0x10);
   }

#if DEBUG_DETECT
   if (flag) printk( " SUCCESS\n" );
   else      printk( " FAILURE\n" );
#endif

   if (!flag) return 0;		/* iobase not found */

   *irq    = fdomain_get_irq( base );
   *iobase = base;

   return 1;			/* success */
}

#else /* PCMCIA */

static int fdomain_isa_detect( int *irq, int *iobase )
{
	if (irq)
		*irq = 0;
	if (iobase)
		*iobase = 0;
	return 0;
}

#endif /* !PCMCIA */


/* PCI detection function: int fdomain_pci_bios_detect(int* irq, int*
   iobase) This function gets the Interrupt Level and I/O base address from
   the PCI configuration registers. */

#ifdef CONFIG_PCI
static int fdomain_pci_bios_detect( int *irq, int *iobase, struct pci_dev **ret_pdev )
{
   unsigned int     pci_irq;                /* PCI interrupt line */
   unsigned long    pci_base;               /* PCI I/O base address */
   struct pci_dev   *pdev = NULL;

#if DEBUG_DETECT
   /* Tell how to print a list of the known PCI devices from bios32 and
      list vendor and device IDs being used if in debug mode.  */
      
   printk( "scsi: <fdomain> INFO: use lspci -v to see list of PCI devices\n" );
   printk( "scsi: <fdomain> TMC-3260 detect:"
	   " Using Vendor ID: 0x%x and Device ID: 0x%x\n",
	   PCI_VENDOR_ID_FD, 
	   PCI_DEVICE_ID_FD_36C70 );
#endif 

   if ((pdev = pci_get_device(PCI_VENDOR_ID_FD, PCI_DEVICE_ID_FD_36C70, pdev)) == NULL)
		return 0;
   if (pci_enable_device(pdev))
   	goto fail;
       
#if DEBUG_DETECT
   printk( "scsi: <fdomain> TMC-3260 detect:"
	   " PCI bus %u, device %u, function %u\n",
	   pdev->bus->number,
	   PCI_SLOT(pdev->devfn),
	   PCI_FUNC(pdev->devfn));
#endif

   /* We now have the appropriate device function for the FD board so we
      just read the PCI config info from the registers.  */

   pci_base = pci_resource_start(pdev, 0);
   pci_irq = pdev->irq;

   if (!request_region( pci_base, 0x10, "fdomain" ))
   	goto fail;

   /* Now we have the I/O base address and interrupt from the PCI
      configuration registers. */

   *irq    = pci_irq;
   *iobase = pci_base;
   *ret_pdev = pdev;

#if DEBUG_DETECT
   printk( "scsi: <fdomain> TMC-3260 detect:"
	   " IRQ = %d, I/O base = 0x%x [0x%lx]\n", *irq, *iobase, pci_base );
#endif

   if (!fdomain_is_valid_port(pci_base)) {
      printk(KERN_ERR "scsi: <fdomain> PCI card detected, but driver not loaded (invalid port)\n" );
      release_region(pci_base, 0x10);
      goto fail;
   }

				/* Fill in a few global variables.  Ugh. */
   bios_major = bios_minor = -1;
   PCI_bus    = 1;
   PCI_dev    = pdev;
   Quantum    = 0;
   bios_base  = 0;
   
   return 1;
fail:
   pci_dev_put(pdev);
   return 0;
}

#endif

struct Scsi_Host *__fdomain_16x0_detect(struct scsi_host_template *tpnt )
{
   int              retcode;
   struct Scsi_Host *shpnt;
   struct pci_dev *pdev = NULL;

   if (setup_called) {
#if DEBUG_DETECT
      printk( "scsi: <fdomain> No BIOS, using port_base = 0x%x, irq = %d\n",
	      port_base, interrupt_level );
#endif
      if (!request_region(port_base, 0x10, "fdomain")) {
	 printk( "scsi: <fdomain> port 0x%x is busy\n", port_base );
	 printk( "scsi: <fdomain> Bad LILO/INSMOD parameters?\n" );
	 return NULL;
      }
      if (!fdomain_is_valid_port( port_base )) {
	 printk( "scsi: <fdomain> Cannot locate chip at port base 0x%x\n",
		 port_base );
	 printk( "scsi: <fdomain> Bad LILO/INSMOD parameters?\n" );
	 release_region(port_base, 0x10);
	 return NULL;
      }
   } else {
      int flag = 0;

#ifdef CONFIG_PCI
				/* Try PCI detection first */
      flag = fdomain_pci_bios_detect( &interrupt_level, &port_base, &pdev );
#endif
      if (!flag) {
				/* Then try ISA bus detection */
	 flag = fdomain_isa_detect( &interrupt_level, &port_base );

	 if (!flag) {
	    printk( "scsi: <fdomain> Detection failed (no card)\n" );
	    return NULL;
	 }
      }
   }

   fdomain_16x0_bus_reset(NULL);

   if (fdomain_test_loopback()) {
      printk(KERN_ERR  "scsi: <fdomain> Detection failed (loopback test failed at port base 0x%x)\n", port_base);
      if (setup_called) {
	 printk(KERN_ERR "scsi: <fdomain> Bad LILO/INSMOD parameters?\n");
      }
      goto fail;
   }

   if (this_id) {
      tpnt->this_id = (this_id & 0x07);
      adapter_mask  = (1 << tpnt->this_id);
   } else {
      if (PCI_bus || (bios_major == 3 && bios_minor >= 2) || bios_major < 0) {
	 tpnt->this_id = 7;
	 adapter_mask  = 0x80;
      } else {
	 tpnt->this_id = 6;
	 adapter_mask  = 0x40;
      }
   }

/* Print out a banner here in case we can't
   get resources.  */

   shpnt = scsi_register( tpnt, 0 );
   if(shpnt == NULL) {
	release_region(port_base, 0x10);
   	return NULL;
   }
   shpnt->irq = interrupt_level;
   shpnt->io_port = port_base;
   shpnt->n_io_port = 0x10;
   print_banner( shpnt );

   /* Log IRQ with kernel */   
   if (!interrupt_level) {
      printk(KERN_ERR "scsi: <fdomain> Card Detected, but driver not loaded (no IRQ)\n" );
      goto fail;
   } else {
      /* Register the IRQ with the kernel */

      retcode = request_irq( interrupt_level,
			     do_fdomain_16x0_intr, pdev?IRQF_SHARED:0, "fdomain", shpnt);

      if (retcode < 0) {
	 if (retcode == -EINVAL) {
	    printk(KERN_ERR "scsi: <fdomain> IRQ %d is bad!\n", interrupt_level );
	    printk(KERN_ERR "                This shouldn't happen!\n" );
	    printk(KERN_ERR "                Send mail to faith@acm.org\n" );
	 } else if (retcode == -EBUSY) {
	    printk(KERN_ERR "scsi: <fdomain> IRQ %d is already in use!\n", interrupt_level );
	    printk(KERN_ERR "                Please use another IRQ!\n" );
	 } else {
	    printk(KERN_ERR "scsi: <fdomain> Error getting IRQ %d\n", interrupt_level );
	    printk(KERN_ERR "                This shouldn't happen!\n" );
	    printk(KERN_ERR "                Send mail to faith@acm.org\n" );
	 }
	 printk(KERN_ERR "scsi: <fdomain> Detected, but driver not loaded (IRQ)\n" );
	 goto fail;
      }
   }
   return shpnt;
fail:
   pci_dev_put(pdev);
   release_region(port_base, 0x10);
   return NULL;
}

static int fdomain_16x0_detect(struct scsi_host_template *tpnt)
{
	if (fdomain)
		fdomain_setup(fdomain);
	return (__fdomain_16x0_detect(tpnt) != NULL);
}

static const char *fdomain_16x0_info( struct Scsi_Host *ignore )
{
   static char buffer[128];
   char        *pt;
   
   strcpy( buffer, "Future Domain 16-bit SCSI Driver Version" );
   if (strchr( VERSION, ':')) { /* Assume VERSION is an RCS Revision string */
      strcat( buffer, strchr( VERSION, ':' ) + 1 );
      pt = strrchr( buffer, '$') - 1;
      if (!pt)  		/* Stripped RCS Revision string? */
	    pt = buffer + strlen( buffer ) - 1;
      if (*pt != ' ')
	    ++pt;
      *pt = '\0';
   } else {			/* Assume VERSION is a number */
      strcat( buffer, " " VERSION );
   }
      
   return buffer;
}

#if 0
static int fdomain_arbitrate( void )
{
   int           status = 0;
   unsigned long timeout;

#if EVERY_ACCESS
   printk( "fdomain_arbitrate()\n" );
#endif
   
   outb(0x00, port_base + SCSI_Cntl);              /* Disable data drivers */
   outb(adapter_mask, port_base + SCSI_Data_NoACK); /* Set our id bit */
   outb(0x04 | PARITY_MASK, port_base + TMC_Cntl); /* Start arbitration */

   timeout = 500;
   do {
      status = inb(port_base + TMC_Status);        /* Read adapter status */
      if (status & 0x02)		      /* Arbitration complete */
	    return 0;
      mdelay(1);			/* Wait one millisecond */
   } while (--timeout);

   /* Make bus idle */
   fdomain_make_bus_idle();

#if EVERY_ACCESS
   printk( "Arbitration failed, status = %x\n", status );
#endif
#if ERRORS_ONLY
   printk( "scsi: <fdomain> Arbitration failed, status = %x\n", status );
#endif
   return 1;
}
#endif

static int fdomain_select( int target )
{
   int           status;
   unsigned long timeout;
#if ERRORS_ONLY
   static int    flag = 0;
#endif

   outb(0x82, port_base + SCSI_Cntl); /* Bus Enable + Select */
   outb(adapter_mask | (1 << target), port_base + SCSI_Data_NoACK);

   /* Stop arbitration and enable parity */
   outb(PARITY_MASK, port_base + TMC_Cntl); 

   timeout = 350;			/* 350 msec */

   do {
      status = inb(port_base + SCSI_Status); /* Read adapter status */
      if (status & 1) {			/* Busy asserted */
	 /* Enable SCSI Bus (on error, should make bus idle with 0) */
	 outb(0x80, port_base + SCSI_Cntl);
	 return 0;
      }
      mdelay(1);			/* wait one msec */
   } while (--timeout);
   /* Make bus idle */
   fdomain_make_bus_idle();
#if EVERY_ACCESS
   if (!target) printk( "Selection failed\n" );
#endif
#if ERRORS_ONLY
   if (!target) {
      if (!flag) /* Skip first failure for all chips. */
	    ++flag;
      else
	    printk( "scsi: <fdomain> Selection failed\n" );
   }
#endif
   return 1;
}

static void my_done(int error)
{
   if (in_command) {
      in_command = 0;
      outb(0x00, port_base + Interrupt_Cntl);
      fdomain_make_bus_idle();
      current_SC->result = error;
      if (current_SC->scsi_done)
	    current_SC->scsi_done( current_SC );
      else panic( "scsi: <fdomain> current_SC->scsi_done() == NULL" );
   } else {
      panic( "scsi: <fdomain> my_done() called outside of command\n" );
   }
#if DEBUG_RACE
   in_interrupt_flag = 0;
#endif
}

static irqreturn_t do_fdomain_16x0_intr(int irq, void *dev_id)
{
   unsigned long flags;
   int      status;
   int      done = 0;
   unsigned data_count;

				/* The fdomain_16x0_intr is only called via
				   the interrupt handler.  The goal of the
				   sti() here is to allow other
				   interruptions while this routine is
				   running. */

   /* Check for other IRQ sources */
   if ((inb(port_base + TMC_Status) & 0x01) == 0)
   	return IRQ_NONE;

   /* It is our IRQ */   	
   outb(0x00, port_base + Interrupt_Cntl);

   /* We usually have one spurious interrupt after each command.  Ignore it. */
   if (!in_command || !current_SC) {	/* Spurious interrupt */
#if EVERY_ACCESS
      printk( "Spurious interrupt, in_command = %d, current_SC = %x\n",
	      in_command, current_SC );
#endif
      return IRQ_NONE;
   }

   /* Abort calls my_done, so we do nothing here. */
   if (current_SC->SCp.phase & aborted) {
#if DEBUG_ABORT
      printk( "scsi: <fdomain> Interrupt after abort, ignoring\n" );
#endif
      /*
      return IRQ_HANDLED; */
   }

#if DEBUG_RACE
   ++in_interrupt_flag;
#endif

   if (current_SC->SCp.phase & in_arbitration) {
      status = inb(port_base + TMC_Status);        /* Read adapter status */
      if (!(status & 0x02)) {
#if EVERY_ACCESS
	 printk( " AFAIL " );
#endif
         spin_lock_irqsave(current_SC->device->host->host_lock, flags);
	 my_done( DID_BUS_BUSY << 16 );
         spin_unlock_irqrestore(current_SC->device->host->host_lock, flags);
	 return IRQ_HANDLED;
      }
      current_SC->SCp.phase = in_selection;
      
      outb(0x40 | FIFO_COUNT, port_base + Interrupt_Cntl);

      outb(0x82, port_base + SCSI_Cntl); /* Bus Enable + Select */
      outb(adapter_mask | (1 << scmd_id(current_SC)), port_base + SCSI_Data_NoACK);
      
      /* Stop arbitration and enable parity */
      outb(0x10 | PARITY_MASK, port_base + TMC_Cntl);
#if DEBUG_RACE
      in_interrupt_flag = 0;
#endif
      return IRQ_HANDLED;
   } else if (current_SC->SCp.phase & in_selection) {
      status = inb(port_base + SCSI_Status);
      if (!(status & 0x01)) {
	 /* Try again, for slow devices */
	 if (fdomain_select( scmd_id(current_SC) )) {
#if EVERY_ACCESS
	    printk( " SFAIL " );
#endif
            spin_lock_irqsave(current_SC->device->host->host_lock, flags);
	    my_done( DID_NO_CONNECT << 16 );
            spin_unlock_irqrestore(current_SC->device->host->host_lock, flags);
	    return IRQ_HANDLED;
	 } else {
#if EVERY_ACCESS
	    printk( " AltSel " );
#endif
	    /* Stop arbitration and enable parity */
	    outb(0x10 | PARITY_MASK, port_base + TMC_Cntl);
	 }
      }
      current_SC->SCp.phase = in_other;
      outb(0x90 | FIFO_COUNT, port_base + Interrupt_Cntl);
      outb(0x80, port_base + SCSI_Cntl);
#if DEBUG_RACE
      in_interrupt_flag = 0;
#endif
      return IRQ_HANDLED;
   }
   
   /* current_SC->SCp.phase == in_other: this is the body of the routine */
   
   status = inb(port_base + SCSI_Status);
   
   if (status & 0x10) {	/* REQ */
      
      switch (status & 0x0e) {
       
      case 0x08:		/* COMMAND OUT */
	 outb(current_SC->cmnd[current_SC->SCp.sent_command++],
	      port_base + Write_SCSI_Data);
#if EVERY_ACCESS
	 printk( "CMD = %x,",
		 current_SC->cmnd[ current_SC->SCp.sent_command - 1] );
#endif
	 break;
      case 0x00:		/* DATA OUT -- tmc18c50/tmc18c30 only */
	 if (chip != tmc1800 && !current_SC->SCp.have_data_in) {
	    current_SC->SCp.have_data_in = -1;
	    outb(0xd0 | PARITY_MASK, port_base + TMC_Cntl);
	 }
	 break;
      case 0x04:		/* DATA IN -- tmc18c50/tmc18c30 only */
	 if (chip != tmc1800 && !current_SC->SCp.have_data_in) {
	    current_SC->SCp.have_data_in = 1;
	    outb(0x90 | PARITY_MASK, port_base + TMC_Cntl);
	 }
	 break;
      case 0x0c:		/* STATUS IN */
	 current_SC->SCp.Status = inb(port_base + Read_SCSI_Data);
#if EVERY_ACCESS
	 printk( "Status = %x, ", current_SC->SCp.Status );
#endif
#if ERRORS_ONLY
	 if (current_SC->SCp.Status
	     && current_SC->SCp.Status != 2
	     && current_SC->SCp.Status != 8) {
	    printk( "scsi: <fdomain> target = %d, command = %x, status = %x\n",
		    current_SC->device->id,
		    current_SC->cmnd[0],
		    current_SC->SCp.Status );
	 }
#endif
	       break;
      case 0x0a:		/* MESSAGE OUT */
	 outb(MESSAGE_REJECT, port_base + Write_SCSI_Data); /* Reject */
	 break;
      case 0x0e:		/* MESSAGE IN */
	 current_SC->SCp.Message = inb(port_base + Read_SCSI_Data);
#if EVERY_ACCESS
	 printk( "Message = %x, ", current_SC->SCp.Message );
#endif
	 if (!current_SC->SCp.Message) ++done;
#if DEBUG_MESSAGES || EVERY_ACCESS
	 if (current_SC->SCp.Message) {
	    printk( "scsi: <fdomain> message = %x\n",
		    current_SC->SCp.Message );
	 }
#endif
	 break;
      }
   }

   if (chip == tmc1800 && !current_SC->SCp.have_data_in
       && (current_SC->SCp.sent_command >= current_SC->cmd_len)) {
      
      if(current_SC->sc_data_direction == DMA_TO_DEVICE)
      {
	 current_SC->SCp.have_data_in = -1;
	 outb(0xd0 | PARITY_MASK, port_base + TMC_Cntl);
      }
      else
      {
	 current_SC->SCp.have_data_in = 1;
	 outb(0x90 | PARITY_MASK, port_base + TMC_Cntl);
      }
   }

   if (current_SC->SCp.have_data_in == -1) { /* DATA OUT */
      while ((data_count = FIFO_Size - inw(port_base + FIFO_Data_Count)) > 512) {
#if EVERY_ACCESS
	 printk( "DC=%d, ", data_count ) ;
#endif
	 if (data_count > current_SC->SCp.this_residual)
	       data_count = current_SC->SCp.this_residual;
	 if (data_count > 0) {
#if EVERY_ACCESS
	    printk( "%d OUT, ", data_count );
#endif
	    if (data_count == 1) {
	       outb(*current_SC->SCp.ptr++, port_base + Write_FIFO);
	       --current_SC->SCp.this_residual;
	    } else {
	       data_count >>= 1;
	       outsw(port_base + Write_FIFO, current_SC->SCp.ptr, data_count);
	       current_SC->SCp.ptr += 2 * data_count;
	       current_SC->SCp.this_residual -= 2 * data_count;
	    }
	 }
	 if (!current_SC->SCp.this_residual) {
	    if (current_SC->SCp.buffers_residual) {
	       --current_SC->SCp.buffers_residual;
	       ++current_SC->SCp.buffer;
	       current_SC->SCp.ptr = sg_virt(current_SC->SCp.buffer);
	       current_SC->SCp.this_residual = current_SC->SCp.buffer->length;
	    } else
		  break;
	 }
      }
   }
   
   if (current_SC->SCp.have_data_in == 1) { /* DATA IN */
      while ((data_count = inw(port_base + FIFO_Data_Count)) > 0) {
#if EVERY_ACCESS
	 printk( "DC=%d, ", data_count );
#endif
	 if (data_count > current_SC->SCp.this_residual)
	       data_count = current_SC->SCp.this_residual;
	 if (data_count) {
#if EVERY_ACCESS
	    printk( "%d IN, ", data_count );
#endif
	    if (data_count == 1) {
	       *current_SC->SCp.ptr++ = inb(port_base + Read_FIFO);
	       --current_SC->SCp.this_residual;
	    } else {
	       data_count >>= 1; /* Number of words */
	       insw(port_base + Read_FIFO, current_SC->SCp.ptr, data_count);
	       current_SC->SCp.ptr += 2 * data_count;
	       current_SC->SCp.this_residual -= 2 * data_count;
	    }
	 }
	 if (!current_SC->SCp.this_residual
	     && current_SC->SCp.buffers_residual) {
	    --current_SC->SCp.buffers_residual;
	    ++current_SC->SCp.buffer;
	    current_SC->SCp.ptr = sg_virt(current_SC->SCp.buffer);
	    current_SC->SCp.this_residual = current_SC->SCp.buffer->length;
	 }
      }
   }
   
   if (done) {
#if EVERY_ACCESS
      printk( " ** IN DONE %d ** ", current_SC->SCp.have_data_in );
#endif

#if ERRORS_ONLY
      if (current_SC->cmnd[0] == REQUEST_SENSE && !current_SC->SCp.Status) {
	      char *buf = scsi_sglist(current_SC);
	 if ((unsigned char)(*(buf + 2)) & 0x0f) {
	    unsigned char key;
	    unsigned char code;
	    unsigned char qualifier;

	    key = (unsigned char)(*(buf + 2)) & 0x0f;
	    code = (unsigned char)(*(buf + 12));
	    qualifier = (unsigned char)(*(buf + 13));

	    if (key != UNIT_ATTENTION
		&& !(key == NOT_READY
		     && code == 0x04
		     && (!qualifier || qualifier == 0x02 || qualifier == 0x01))
		&& !(key == ILLEGAL_REQUEST && (code == 0x25
						|| code == 0x24
						|| !code)))
		  
		  printk( "scsi: <fdomain> REQUEST SENSE"
			  " Key = %x, Code = %x, Qualifier = %x\n",
			  key, code, qualifier );
	 }
      }
#endif
#if EVERY_ACCESS
      printk( "BEFORE MY_DONE. . ." );
#endif
      spin_lock_irqsave(current_SC->device->host->host_lock, flags);
      my_done( (current_SC->SCp.Status & 0xff)
	       | ((current_SC->SCp.Message & 0xff) << 8) | (DID_OK << 16) );
      spin_unlock_irqrestore(current_SC->device->host->host_lock, flags);
#if EVERY_ACCESS
      printk( "RETURNING.\n" );
#endif
      
   } else {
      if (current_SC->SCp.phase & disconnect) {
	 outb(0xd0 | FIFO_COUNT, port_base + Interrupt_Cntl);
	 outb(0x00, port_base + SCSI_Cntl);
      } else {
	 outb(0x90 | FIFO_COUNT, port_base + Interrupt_Cntl);
      }
   }
#if DEBUG_RACE
   in_interrupt_flag = 0;
#endif
   return IRQ_HANDLED;
}

static int fdomain_16x0_queue_lck(struct scsi_cmnd *SCpnt,
		void (*done)(struct scsi_cmnd *))
{
   if (in_command) {
      panic( "scsi: <fdomain> fdomain_16x0_queue() NOT REENTRANT!\n" );
   }
#if EVERY_ACCESS
   printk( "queue: target = %d cmnd = 0x%02x pieces = %d size = %u\n",
	   SCpnt->target,
	   *(unsigned char *)SCpnt->cmnd,
	   scsi_sg_count(SCpnt),
	   scsi_bufflen(SCpnt));
#endif

   fdomain_make_bus_idle();

   current_SC            = SCpnt; /* Save this for the done function */
   current_SC->scsi_done = done;

   /* Initialize static data */

   if (scsi_sg_count(current_SC)) {
	   current_SC->SCp.buffer = scsi_sglist(current_SC);
	   current_SC->SCp.ptr = sg_virt(current_SC->SCp.buffer);
	   current_SC->SCp.this_residual    = current_SC->SCp.buffer->length;
	   current_SC->SCp.buffers_residual = scsi_sg_count(current_SC) - 1;
   } else {
	   current_SC->SCp.ptr              = NULL;
	   current_SC->SCp.this_residual    = 0;
	   current_SC->SCp.buffer           = NULL;
	   current_SC->SCp.buffers_residual = 0;
   }

   current_SC->SCp.Status              = 0;
   current_SC->SCp.Message             = 0;
   current_SC->SCp.have_data_in        = 0;
   current_SC->SCp.sent_command        = 0;
   current_SC->SCp.phase               = in_arbitration;

   /* Start arbitration */
   outb(0x00, port_base + Interrupt_Cntl);
   outb(0x00, port_base + SCSI_Cntl);              /* Disable data drivers */
   outb(adapter_mask, port_base + SCSI_Data_NoACK); /* Set our id bit */
   ++in_command;
   outb(0x20, port_base + Interrupt_Cntl);
   outb(0x14 | PARITY_MASK, port_base + TMC_Cntl); /* Start arbitration */

   return 0;
}

static DEF_SCSI_QCMD(fdomain_16x0_queue)

#if DEBUG_ABORT
static void print_info(struct scsi_cmnd *SCpnt)
{
   unsigned int imr;
   unsigned int irr;
   unsigned int isr;

   if (!SCpnt || !SCpnt->device || !SCpnt->device->host) {
      printk(KERN_WARNING "scsi: <fdomain> Cannot provide detailed information\n");
      return;
   }
   
   printk(KERN_INFO "%s\n", fdomain_16x0_info( SCpnt->device->host ) );
   print_banner(SCpnt->device->host);
   switch (SCpnt->SCp.phase) {
   case in_arbitration: printk("arbitration"); break;
   case in_selection:   printk("selection");   break;
   case in_other:       printk("other");       break;
   default:             printk("unknown");     break;
   }

   printk( " (%d), target = %d cmnd = 0x%02x pieces = %d size = %u\n",
	   SCpnt->SCp.phase,
	   SCpnt->device->id,
	   *(unsigned char *)SCpnt->cmnd,
	   scsi_sg_count(SCpnt),
	   scsi_bufflen(SCpnt));
   printk( "sent_command = %d, have_data_in = %d, timeout = %d\n",
	   SCpnt->SCp.sent_command,
	   SCpnt->SCp.have_data_in,
	   SCpnt->timeout );
#if DEBUG_RACE
   printk( "in_interrupt_flag = %d\n", in_interrupt_flag );
#endif

   imr = (inb( 0x0a1 ) << 8) + inb( 0x21 );
   outb( 0x0a, 0xa0 );
   irr = inb( 0xa0 ) << 8;
   outb( 0x0a, 0x20 );
   irr += inb( 0x20 );
   outb( 0x0b, 0xa0 );
   isr = inb( 0xa0 ) << 8;
   outb( 0x0b, 0x20 );
   isr += inb( 0x20 );

				/* Print out interesting information */
   printk( "IMR = 0x%04x", imr );
   if (imr & (1 << interrupt_level))
	 printk( " (masked)" );
   printk( ", IRR = 0x%04x, ISR = 0x%04x\n", irr, isr );

   printk( "SCSI Status      = 0x%02x\n", inb(port_base + SCSI_Status));
   printk( "TMC Status       = 0x%02x", inb(port_base + TMC_Status));
   if (inb((port_base + TMC_Status) & 1))
	 printk( " (interrupt)" );
   printk( "\n" );
   printk("Interrupt Status = 0x%02x", inb(port_base + Interrupt_Status));
   if (inb(port_base + Interrupt_Status) & 0x08)
	 printk( " (enabled)" );
   printk( "\n" );
   if (chip == tmc18c50 || chip == tmc18c30) {
      printk("FIFO Status      = 0x%02x\n", inb(port_base + FIFO_Status));
      printk( "Int. Condition   = 0x%02x\n",
	      inb( port_base + Interrupt_Cond ) );
   }
   printk( "Configuration 1  = 0x%02x\n", inb( port_base + Configuration1 ) );
   if (chip == tmc18c50 || chip == tmc18c30)
	 printk( "Configuration 2  = 0x%02x\n",
		 inb( port_base + Configuration2 ) );
}
#endif

static int fdomain_16x0_abort(struct scsi_cmnd *SCpnt)
{
#if EVERY_ACCESS || ERRORS_ONLY || DEBUG_ABORT
   printk( "scsi: <fdomain> abort " );
#endif

   if (!in_command) {
#if EVERY_ACCESS || ERRORS_ONLY
      printk( " (not in command)\n" );
#endif
      return FAILED;
   } else printk( "\n" );

#if DEBUG_ABORT
   print_info( SCpnt );
#endif

   fdomain_make_bus_idle();
   current_SC->SCp.phase |= aborted;
   current_SC->result = DID_ABORT << 16;
   
   /* Aborts are not done well. . . */
   my_done(DID_ABORT << 16);
   return SUCCESS;
}

int fdomain_16x0_bus_reset(struct scsi_cmnd *SCpnt)
{
   unsigned long flags;

   local_irq_save(flags);

   outb(1, port_base + SCSI_Cntl);
   do_pause( 2 );
   outb(0, port_base + SCSI_Cntl);
   do_pause( 115 );
   outb(0, port_base + SCSI_Mode_Cntl);
   outb(PARITY_MASK, port_base + TMC_Cntl);

   local_irq_restore(flags);
   return SUCCESS;
}

static int fdomain_16x0_biosparam(struct scsi_device *sdev,
		struct block_device *bdev,
		sector_t capacity, int *info_array)
{
   int              drive;
   int		    size      = capacity;
   unsigned long    offset;
   struct drive_info {
      unsigned short cylinders;
      unsigned char  heads;
      unsigned char  sectors;
   } i;
   
   /* NOTES:
      The RAM area starts at 0x1f00 from the bios_base address.

      For BIOS Version 2.0:
      
      The drive parameter table seems to start at 0x1f30.
      The first byte's purpose is not known.
      Next is the cylinder, head, and sector information.
      The last 4 bytes appear to be the drive's size in sectors.
      The other bytes in the drive parameter table are unknown.
      If anyone figures them out, please send me mail, and I will
      update these notes.

      Tape drives do not get placed in this table.

      There is another table at 0x1fea:
      If the byte is 0x01, then the SCSI ID is not in use.
      If the byte is 0x18 or 0x48, then the SCSI ID is in use,
      although tapes don't seem to be in this table.  I haven't
      seen any other numbers (in a limited sample).

      0x1f2d is a drive count (i.e., not including tapes)

      The table at 0x1fcc are I/O ports addresses for the various
      operations.  I calculate these by hand in this driver code.

      
      
      For the ISA-200S version of BIOS Version 2.0:

      The drive parameter table starts at 0x1f33.

      WARNING: Assume that the table entry is 25 bytes long.  Someone needs
      to check this for the Quantum ISA-200S card.

      
      
      For BIOS Version 3.2:

      The drive parameter table starts at 0x1f70.  Each entry is
      0x0a bytes long.  Heads are one less than we need to report.
    */

   if (MAJOR(bdev->bd_dev) != SCSI_DISK0_MAJOR) {
      printk("scsi: <fdomain> fdomain_16x0_biosparam: too many disks");
      return 0;
   }
   drive = MINOR(bdev->bd_dev) >> 4;

   if (bios_major == 2) {
      switch (Quantum) {
      case 2:			/* ISA_200S */
				/* The value of 25 has never been verified.
				   It should probably be 15. */
	 offset = 0x1f33 + drive * 25;
	 break;
      case 3:			/* ISA_250MG */
	 offset = 0x1f36 + drive * 15;
	 break;
      case 4:			/* ISA_200S (another one) */
	 offset = 0x1f34 + drive * 15;
	 break;
      default:
	 offset = 0x1f31 + drive * 25;
	 break;
      }
      memcpy_fromio( &i, bios_mem + offset, sizeof( struct drive_info ) );
      info_array[0] = i.heads;
      info_array[1] = i.sectors;
      info_array[2] = i.cylinders;
   } else if (bios_major == 3
	      && bios_minor >= 0
	      && bios_minor < 4) { /* 3.0 and 3.2 BIOS */
      memcpy_fromio( &i, bios_mem + 0x1f71 + drive * 10,
		     sizeof( struct drive_info ) );
      info_array[0] = i.heads + 1;
      info_array[1] = i.sectors;
      info_array[2] = i.cylinders;
   } else {			/* 3.4 BIOS (and up?) */
      /* This algorithm was provided by Future Domain (much thanks!). */
      unsigned char *p = scsi_bios_ptable(bdev);

      if (p && p[65] == 0xaa && p[64] == 0x55 /* Partition table valid */
	  && p[4]) {			    /* Partition type */

	 /* The partition table layout is as follows:

	    Start: 0x1b3h
	    Offset: 0 = partition status
		    1 = starting head
		    2 = starting sector and cylinder (word, encoded)
		    4 = partition type
		    5 = ending head
		    6 = ending sector and cylinder (word, encoded)
		    8 = starting absolute sector (double word)
		    c = number of sectors (double word)
	    Signature: 0x1fe = 0x55aa

	    So, this algorithm assumes:
	    1) the first partition table is in use,
	    2) the data in the first entry is correct, and
	    3) partitions never divide cylinders

	    Note that (1) may be FALSE for NetBSD (and other BSD flavors),
	    as well as for Linux.  Note also, that Linux doesn't pay any
	    attention to the fields that are used by this algorithm -- it
	    only uses the absolute sector data.  Recent versions of Linux's
	    fdisk(1) will fill this data in correctly, and forthcoming
	    versions will check for consistency.

	    Checking for a non-zero partition type is not part of the
	    Future Domain algorithm, but it seemed to be a reasonable thing
	    to do, especially in the Linux and BSD worlds. */

	 info_array[0] = p[5] + 1;	    /* heads */
	 info_array[1] = p[6] & 0x3f;	    /* sectors */
      } else {

 	 /* Note that this new method guarantees that there will always be
	    less than 1024 cylinders on a platter.  This is good for drives
	    up to approximately 7.85GB (where 1GB = 1024 * 1024 kB). */

	 if ((unsigned int)size >= 0x7e0000U) {
	    info_array[0] = 0xff; /* heads   = 255 */
	    info_array[1] = 0x3f; /* sectors =  63 */
	 } else if ((unsigned int)size >= 0x200000U) {
	    info_array[0] = 0x80; /* heads   = 128 */
	    info_array[1] = 0x3f; /* sectors =  63 */
	 } else {
	    info_array[0] = 0x40; /* heads   =  64 */
	    info_array[1] = 0x20; /* sectors =  32 */
	 }
      }
				/* For both methods, compute the cylinders */
      info_array[2] = (unsigned int)size / (info_array[0] * info_array[1] );
      kfree(p);
   }
   
   return 0;
}

static int fdomain_16x0_release(struct Scsi_Host *shpnt)
{
	if (shpnt->irq)
		free_irq(shpnt->irq, shpnt);
	if (shpnt->io_port && shpnt->n_io_port)
		release_region(shpnt->io_port, shpnt->n_io_port);
	if (PCI_bus)
		pci_dev_put(PCI_dev);
	return 0;
}

struct scsi_host_template fdomain_driver_template = {
	.module			= THIS_MODULE,
	.name			= "fdomain",
	.proc_name		= "fdomain",
	.detect			= fdomain_16x0_detect,
	.info			= fdomain_16x0_info,
	.queuecommand		= fdomain_16x0_queue,
	.eh_abort_handler	= fdomain_16x0_abort,
	.eh_bus_reset_handler	= fdomain_16x0_bus_reset,
	.bios_param		= fdomain_16x0_biosparam,
	.release		= fdomain_16x0_release,
	.can_queue		= 1,
	.this_id		= 6,
	.sg_tablesize		= 64,
	.use_clustering		= DISABLE_CLUSTERING,
};

#ifndef PCMCIA
#ifdef CONFIG_PCI

static struct pci_device_id fdomain_pci_tbl[] = {
	{ PCI_VENDOR_ID_FD, PCI_DEVICE_ID_FD_36C70,
	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0UL },
	{ }
};
MODULE_DEVICE_TABLE(pci, fdomain_pci_tbl);
#endif
#define driver_template fdomain_driver_template
#include "scsi_module.c"

#endif