spi-bfin5xx.c 40.1 KB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701 702 703 704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999 1000 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060 1061 1062 1063 1064 1065 1066 1067 1068 1069 1070 1071 1072 1073 1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 1126 1127 1128 1129 1130 1131 1132 1133 1134 1135 1136 1137 1138 1139 1140 1141 1142 1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1211 1212 1213 1214 1215 1216 1217 1218 1219 1220 1221 1222 1223 1224 1225 1226 1227 1228 1229 1230 1231 1232 1233 1234 1235 1236 1237 1238 1239 1240 1241 1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 1252 1253 1254 1255 1256 1257 1258 1259 1260 1261 1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 1272 1273 1274 1275 1276 1277 1278 1279 1280 1281 1282 1283 1284 1285 1286 1287 1288 1289 1290 1291 1292 1293 1294 1295 1296 1297 1298 1299 1300 1301 1302 1303 1304 1305 1306 1307 1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339 1340 1341 1342 1343 1344 1345 1346 1347 1348 1349 1350 1351 1352 1353 1354 1355 1356 1357 1358 1359 1360 1361 1362 1363 1364 1365 1366 1367 1368 1369 1370 1371 1372 1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 1389 1390 1391 1392 1393 1394 1395 1396 1397 1398 1399 1400 1401 1402 1403 1404 1405 1406 1407 1408 1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440 1441 1442 1443 1444 1445 1446 1447 1448 1449 1450 1451 1452 1453 1454 1455 1456 1457 1458 1459 1460 1461 1462 1463 1464 1465 1466 1467 1468 1469 1470 1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482
/*
 * Blackfin On-Chip SPI Driver
 *
 * Copyright 2004-2010 Analog Devices Inc.
 *
 * Enter bugs at http://blackfin.uclinux.org/
 *
 * Licensed under the GPL-2 or later.
 */

#include <linux/init.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/slab.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/irq.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/spi/spi.h>
#include <linux/workqueue.h>

#include <asm/dma.h>
#include <asm/portmux.h>
#include <asm/bfin5xx_spi.h>
#include <asm/cacheflush.h>

#define DRV_NAME	"bfin-spi"
#define DRV_AUTHOR	"Bryan Wu, Luke Yang"
#define DRV_DESC	"Blackfin on-chip SPI Controller Driver"
#define DRV_VERSION	"1.0"

MODULE_AUTHOR(DRV_AUTHOR);
MODULE_DESCRIPTION(DRV_DESC);
MODULE_LICENSE("GPL");

#define START_STATE	((void *)0)
#define RUNNING_STATE	((void *)1)
#define DONE_STATE	((void *)2)
#define ERROR_STATE	((void *)-1)

struct bfin_spi_master_data;

struct bfin_spi_transfer_ops {
	void (*write) (struct bfin_spi_master_data *);
	void (*read) (struct bfin_spi_master_data *);
	void (*duplex) (struct bfin_spi_master_data *);
};

struct bfin_spi_master_data {
	/* Driver model hookup */
	struct platform_device *pdev;

	/* SPI framework hookup */
	struct spi_master *master;

	/* Regs base of SPI controller */
	struct bfin_spi_regs __iomem *regs;

	/* Pin request list */
	u16 *pin_req;

	/* BFIN hookup */
	struct bfin5xx_spi_master *master_info;

	/* Driver message queue */
	struct workqueue_struct *workqueue;
	struct work_struct pump_messages;
	spinlock_t lock;
	struct list_head queue;
	int busy;
	bool running;

	/* Message Transfer pump */
	struct tasklet_struct pump_transfers;

	/* Current message transfer state info */
	struct spi_message *cur_msg;
	struct spi_transfer *cur_transfer;
	struct bfin_spi_slave_data *cur_chip;
	size_t len_in_bytes;
	size_t len;
	void *tx;
	void *tx_end;
	void *rx;
	void *rx_end;

	/* DMA stuffs */
	int dma_channel;
	int dma_mapped;
	int dma_requested;
	dma_addr_t rx_dma;
	dma_addr_t tx_dma;

	int irq_requested;
	int spi_irq;

	size_t rx_map_len;
	size_t tx_map_len;
	u8 n_bytes;
	u16 ctrl_reg;
	u16 flag_reg;

	int cs_change;
	const struct bfin_spi_transfer_ops *ops;
};

struct bfin_spi_slave_data {
	u16 ctl_reg;
	u16 baud;
	u16 flag;

	u8 chip_select_num;
	u8 enable_dma;
	u16 cs_chg_udelay;	/* Some devices require > 255usec delay */
	u32 cs_gpio;
	u16 idle_tx_val;
	u8 pio_interrupt;	/* use spi data irq */
	const struct bfin_spi_transfer_ops *ops;
};

static void bfin_spi_enable(struct bfin_spi_master_data *drv_data)
{
	bfin_write_or(&drv_data->regs->ctl, BIT_CTL_ENABLE);
}

static void bfin_spi_disable(struct bfin_spi_master_data *drv_data)
{
	bfin_write_and(&drv_data->regs->ctl, ~BIT_CTL_ENABLE);
}

/* Caculate the SPI_BAUD register value based on input HZ */
static u16 hz_to_spi_baud(u32 speed_hz)
{
	u_long sclk = get_sclk();
	u16 spi_baud = (sclk / (2 * speed_hz));

	if ((sclk % (2 * speed_hz)) > 0)
		spi_baud++;

	if (spi_baud < MIN_SPI_BAUD_VAL)
		spi_baud = MIN_SPI_BAUD_VAL;

	return spi_baud;
}

static int bfin_spi_flush(struct bfin_spi_master_data *drv_data)
{
	unsigned long limit = loops_per_jiffy << 1;

	/* wait for stop and clear stat */
	while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_SPIF) && --limit)
		cpu_relax();

	bfin_write(&drv_data->regs->stat, BIT_STAT_CLR);

	return limit;
}

/* Chip select operation functions for cs_change flag */
static void bfin_spi_cs_active(struct bfin_spi_master_data *drv_data, struct bfin_spi_slave_data *chip)
{
	if (likely(chip->chip_select_num < MAX_CTRL_CS))
		bfin_write_and(&drv_data->regs->flg, ~chip->flag);
	else
		gpio_set_value(chip->cs_gpio, 0);
}

static void bfin_spi_cs_deactive(struct bfin_spi_master_data *drv_data,
                                 struct bfin_spi_slave_data *chip)
{
	if (likely(chip->chip_select_num < MAX_CTRL_CS))
		bfin_write_or(&drv_data->regs->flg, chip->flag);
	else
		gpio_set_value(chip->cs_gpio, 1);

	/* Move delay here for consistency */
	if (chip->cs_chg_udelay)
		udelay(chip->cs_chg_udelay);
}

/* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
static inline void bfin_spi_cs_enable(struct bfin_spi_master_data *drv_data,
                                      struct bfin_spi_slave_data *chip)
{
	if (chip->chip_select_num < MAX_CTRL_CS)
		bfin_write_or(&drv_data->regs->flg, chip->flag >> 8);
}

static inline void bfin_spi_cs_disable(struct bfin_spi_master_data *drv_data,
                                       struct bfin_spi_slave_data *chip)
{
	if (chip->chip_select_num < MAX_CTRL_CS)
		bfin_write_and(&drv_data->regs->flg, ~(chip->flag >> 8));
}

/* stop controller and re-config current chip*/
static void bfin_spi_restore_state(struct bfin_spi_master_data *drv_data)
{
	struct bfin_spi_slave_data *chip = drv_data->cur_chip;

	/* Clear status and disable clock */
	bfin_write(&drv_data->regs->stat, BIT_STAT_CLR);
	bfin_spi_disable(drv_data);
	dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n");

	SSYNC();

	/* Load the registers */
	bfin_write(&drv_data->regs->ctl, chip->ctl_reg);
	bfin_write(&drv_data->regs->baud, chip->baud);

	bfin_spi_enable(drv_data);
	bfin_spi_cs_active(drv_data, chip);
}

/* used to kick off transfer in rx mode and read unwanted RX data */
static inline void bfin_spi_dummy_read(struct bfin_spi_master_data *drv_data)
{
	(void) bfin_read(&drv_data->regs->rdbr);
}

static void bfin_spi_u8_writer(struct bfin_spi_master_data *drv_data)
{
	/* clear RXS (we check for RXS inside the loop) */
	bfin_spi_dummy_read(drv_data);

	while (drv_data->tx < drv_data->tx_end) {
		bfin_write(&drv_data->regs->tdbr, (*(u8 *) (drv_data->tx++)));
		/* wait until transfer finished.
		   checking SPIF or TXS may not guarantee transfer completion */
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
			cpu_relax();
		/* discard RX data and clear RXS */
		bfin_spi_dummy_read(drv_data);
	}
}

static void bfin_spi_u8_reader(struct bfin_spi_master_data *drv_data)
{
	u16 tx_val = drv_data->cur_chip->idle_tx_val;

	/* discard old RX data and clear RXS */
	bfin_spi_dummy_read(drv_data);

	while (drv_data->rx < drv_data->rx_end) {
		bfin_write(&drv_data->regs->tdbr, tx_val);
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
			cpu_relax();
		*(u8 *) (drv_data->rx++) = bfin_read(&drv_data->regs->rdbr);
	}
}

static void bfin_spi_u8_duplex(struct bfin_spi_master_data *drv_data)
{
	/* discard old RX data and clear RXS */
	bfin_spi_dummy_read(drv_data);

	while (drv_data->rx < drv_data->rx_end) {
		bfin_write(&drv_data->regs->tdbr, (*(u8 *) (drv_data->tx++)));
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
			cpu_relax();
		*(u8 *) (drv_data->rx++) = bfin_read(&drv_data->regs->rdbr);
	}
}

static const struct bfin_spi_transfer_ops bfin_bfin_spi_transfer_ops_u8 = {
	.write  = bfin_spi_u8_writer,
	.read   = bfin_spi_u8_reader,
	.duplex = bfin_spi_u8_duplex,
};

static void bfin_spi_u16_writer(struct bfin_spi_master_data *drv_data)
{
	/* clear RXS (we check for RXS inside the loop) */
	bfin_spi_dummy_read(drv_data);

	while (drv_data->tx < drv_data->tx_end) {
		bfin_write(&drv_data->regs->tdbr, (*(u16 *) (drv_data->tx)));
		drv_data->tx += 2;
		/* wait until transfer finished.
		   checking SPIF or TXS may not guarantee transfer completion */
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
			cpu_relax();
		/* discard RX data and clear RXS */
		bfin_spi_dummy_read(drv_data);
	}
}

static void bfin_spi_u16_reader(struct bfin_spi_master_data *drv_data)
{
	u16 tx_val = drv_data->cur_chip->idle_tx_val;

	/* discard old RX data and clear RXS */
	bfin_spi_dummy_read(drv_data);

	while (drv_data->rx < drv_data->rx_end) {
		bfin_write(&drv_data->regs->tdbr, tx_val);
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
			cpu_relax();
		*(u16 *) (drv_data->rx) = bfin_read(&drv_data->regs->rdbr);
		drv_data->rx += 2;
	}
}

static void bfin_spi_u16_duplex(struct bfin_spi_master_data *drv_data)
{
	/* discard old RX data and clear RXS */
	bfin_spi_dummy_read(drv_data);

	while (drv_data->rx < drv_data->rx_end) {
		bfin_write(&drv_data->regs->tdbr, (*(u16 *) (drv_data->tx)));
		drv_data->tx += 2;
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
			cpu_relax();
		*(u16 *) (drv_data->rx) = bfin_read(&drv_data->regs->rdbr);
		drv_data->rx += 2;
	}
}

static const struct bfin_spi_transfer_ops bfin_bfin_spi_transfer_ops_u16 = {
	.write  = bfin_spi_u16_writer,
	.read   = bfin_spi_u16_reader,
	.duplex = bfin_spi_u16_duplex,
};

/* test if there is more transfer to be done */
static void *bfin_spi_next_transfer(struct bfin_spi_master_data *drv_data)
{
	struct spi_message *msg = drv_data->cur_msg;
	struct spi_transfer *trans = drv_data->cur_transfer;

	/* Move to next transfer */
	if (trans->transfer_list.next != &msg->transfers) {
		drv_data->cur_transfer =
		    list_entry(trans->transfer_list.next,
			       struct spi_transfer, transfer_list);
		return RUNNING_STATE;
	} else
		return DONE_STATE;
}

/*
 * caller already set message->status;
 * dma and pio irqs are blocked give finished message back
 */
static void bfin_spi_giveback(struct bfin_spi_master_data *drv_data)
{
	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
	struct spi_transfer *last_transfer;
	unsigned long flags;
	struct spi_message *msg;

	spin_lock_irqsave(&drv_data->lock, flags);
	msg = drv_data->cur_msg;
	drv_data->cur_msg = NULL;
	drv_data->cur_transfer = NULL;
	drv_data->cur_chip = NULL;
	queue_work(drv_data->workqueue, &drv_data->pump_messages);
	spin_unlock_irqrestore(&drv_data->lock, flags);

	last_transfer = list_entry(msg->transfers.prev,
				   struct spi_transfer, transfer_list);

	msg->state = NULL;

	if (!drv_data->cs_change)
		bfin_spi_cs_deactive(drv_data, chip);

	/* Not stop spi in autobuffer mode */
	if (drv_data->tx_dma != 0xFFFF)
		bfin_spi_disable(drv_data);

	if (msg->complete)
		msg->complete(msg->context);
}

/* spi data irq handler */
static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
{
	struct bfin_spi_master_data *drv_data = dev_id;
	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
	struct spi_message *msg = drv_data->cur_msg;
	int n_bytes = drv_data->n_bytes;
	int loop = 0;

	/* wait until transfer finished. */
	while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_RXS))
		cpu_relax();

	if ((drv_data->tx && drv_data->tx >= drv_data->tx_end) ||
		(drv_data->rx && drv_data->rx >= (drv_data->rx_end - n_bytes))) {
		/* last read */
		if (drv_data->rx) {
			dev_dbg(&drv_data->pdev->dev, "last read\n");
			if (!(n_bytes % 2)) {
				u16 *buf = (u16 *)drv_data->rx;
				for (loop = 0; loop < n_bytes / 2; loop++)
					*buf++ = bfin_read(&drv_data->regs->rdbr);
			} else {
				u8 *buf = (u8 *)drv_data->rx;
				for (loop = 0; loop < n_bytes; loop++)
					*buf++ = bfin_read(&drv_data->regs->rdbr);
			}
			drv_data->rx += n_bytes;
		}

		msg->actual_length += drv_data->len_in_bytes;
		if (drv_data->cs_change)
			bfin_spi_cs_deactive(drv_data, chip);
		/* Move to next transfer */
		msg->state = bfin_spi_next_transfer(drv_data);

		disable_irq_nosync(drv_data->spi_irq);

		/* Schedule transfer tasklet */
		tasklet_schedule(&drv_data->pump_transfers);
		return IRQ_HANDLED;
	}

	if (drv_data->rx && drv_data->tx) {
		/* duplex */
		dev_dbg(&drv_data->pdev->dev, "duplex: write_TDBR\n");
		if (!(n_bytes % 2)) {
			u16 *buf = (u16 *)drv_data->rx;
			u16 *buf2 = (u16 *)drv_data->tx;
			for (loop = 0; loop < n_bytes / 2; loop++) {
				*buf++ = bfin_read(&drv_data->regs->rdbr);
				bfin_write(&drv_data->regs->tdbr, *buf2++);
			}
		} else {
			u8 *buf = (u8 *)drv_data->rx;
			u8 *buf2 = (u8 *)drv_data->tx;
			for (loop = 0; loop < n_bytes; loop++) {
				*buf++ = bfin_read(&drv_data->regs->rdbr);
				bfin_write(&drv_data->regs->tdbr, *buf2++);
			}
		}
	} else if (drv_data->rx) {
		/* read */
		dev_dbg(&drv_data->pdev->dev, "read: write_TDBR\n");
		if (!(n_bytes % 2)) {
			u16 *buf = (u16 *)drv_data->rx;
			for (loop = 0; loop < n_bytes / 2; loop++) {
				*buf++ = bfin_read(&drv_data->regs->rdbr);
				bfin_write(&drv_data->regs->tdbr, chip->idle_tx_val);
			}
		} else {
			u8 *buf = (u8 *)drv_data->rx;
			for (loop = 0; loop < n_bytes; loop++) {
				*buf++ = bfin_read(&drv_data->regs->rdbr);
				bfin_write(&drv_data->regs->tdbr, chip->idle_tx_val);
			}
		}
	} else if (drv_data->tx) {
		/* write */
		dev_dbg(&drv_data->pdev->dev, "write: write_TDBR\n");
		if (!(n_bytes % 2)) {
			u16 *buf = (u16 *)drv_data->tx;
			for (loop = 0; loop < n_bytes / 2; loop++) {
				bfin_read(&drv_data->regs->rdbr);
				bfin_write(&drv_data->regs->tdbr, *buf++);
			}
		} else {
			u8 *buf = (u8 *)drv_data->tx;
			for (loop = 0; loop < n_bytes; loop++) {
				bfin_read(&drv_data->regs->rdbr);
				bfin_write(&drv_data->regs->tdbr, *buf++);
			}
		}
	}

	if (drv_data->tx)
		drv_data->tx += n_bytes;
	if (drv_data->rx)
		drv_data->rx += n_bytes;

	return IRQ_HANDLED;
}

static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
{
	struct bfin_spi_master_data *drv_data = dev_id;
	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
	struct spi_message *msg = drv_data->cur_msg;
	unsigned long timeout;
	unsigned short dmastat = get_dma_curr_irqstat(drv_data->dma_channel);
	u16 spistat = bfin_read(&drv_data->regs->stat);

	dev_dbg(&drv_data->pdev->dev,
		"in dma_irq_handler dmastat:0x%x spistat:0x%x\n",
		dmastat, spistat);

	if (drv_data->rx != NULL) {
		u16 cr = bfin_read(&drv_data->regs->ctl);
		/* discard old RX data and clear RXS */
		bfin_spi_dummy_read(drv_data);
		bfin_write(&drv_data->regs->ctl, cr & ~BIT_CTL_ENABLE); /* Disable SPI */
		bfin_write(&drv_data->regs->ctl, cr & ~BIT_CTL_TIMOD); /* Restore State */
		bfin_write(&drv_data->regs->stat, BIT_STAT_CLR); /* Clear Status */
	}

	clear_dma_irqstat(drv_data->dma_channel);

	/*
	 * wait for the last transaction shifted out.  HRM states:
	 * at this point there may still be data in the SPI DMA FIFO waiting
	 * to be transmitted ... software needs to poll TXS in the SPI_STAT
	 * register until it goes low for 2 successive reads
	 */
	if (drv_data->tx != NULL) {
		while ((bfin_read(&drv_data->regs->stat) & BIT_STAT_TXS) ||
		       (bfin_read(&drv_data->regs->stat) & BIT_STAT_TXS))
			cpu_relax();
	}

	dev_dbg(&drv_data->pdev->dev,
		"in dma_irq_handler dmastat:0x%x spistat:0x%x\n",
		dmastat, bfin_read(&drv_data->regs->stat));

	timeout = jiffies + HZ;
	while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_SPIF))
		if (!time_before(jiffies, timeout)) {
			dev_warn(&drv_data->pdev->dev, "timeout waiting for SPIF\n");
			break;
		} else
			cpu_relax();

	if ((dmastat & DMA_ERR) && (spistat & BIT_STAT_RBSY)) {
		msg->state = ERROR_STATE;
		dev_err(&drv_data->pdev->dev, "dma receive: fifo/buffer overflow\n");
	} else {
		msg->actual_length += drv_data->len_in_bytes;

		if (drv_data->cs_change)
			bfin_spi_cs_deactive(drv_data, chip);

		/* Move to next transfer */
		msg->state = bfin_spi_next_transfer(drv_data);
	}

	/* Schedule transfer tasklet */
	tasklet_schedule(&drv_data->pump_transfers);

	/* free the irq handler before next transfer */
	dev_dbg(&drv_data->pdev->dev,
		"disable dma channel irq%d\n",
		drv_data->dma_channel);
	dma_disable_irq_nosync(drv_data->dma_channel);

	return IRQ_HANDLED;
}

static void bfin_spi_pump_transfers(unsigned long data)
{
	struct bfin_spi_master_data *drv_data = (struct bfin_spi_master_data *)data;
	struct spi_message *message = NULL;
	struct spi_transfer *transfer = NULL;
	struct spi_transfer *previous = NULL;
	struct bfin_spi_slave_data *chip = NULL;
	unsigned int bits_per_word;
	u16 cr, cr_width, dma_width, dma_config;
	u32 tranf_success = 1;
	u8 full_duplex = 0;

	/* Get current state information */
	message = drv_data->cur_msg;
	transfer = drv_data->cur_transfer;
	chip = drv_data->cur_chip;

	/*
	 * if msg is error or done, report it back using complete() callback
	 */

	 /* Handle for abort */
	if (message->state == ERROR_STATE) {
		dev_dbg(&drv_data->pdev->dev, "transfer: we've hit an error\n");
		message->status = -EIO;
		bfin_spi_giveback(drv_data);
		return;
	}

	/* Handle end of message */
	if (message->state == DONE_STATE) {
		dev_dbg(&drv_data->pdev->dev, "transfer: all done!\n");
		message->status = 0;
		bfin_spi_flush(drv_data);
		bfin_spi_giveback(drv_data);
		return;
	}

	/* Delay if requested at end of transfer */
	if (message->state == RUNNING_STATE) {
		dev_dbg(&drv_data->pdev->dev, "transfer: still running ...\n");
		previous = list_entry(transfer->transfer_list.prev,
				      struct spi_transfer, transfer_list);
		if (previous->delay_usecs)
			udelay(previous->delay_usecs);
	}

	/* Flush any existing transfers that may be sitting in the hardware */
	if (bfin_spi_flush(drv_data) == 0) {
		dev_err(&drv_data->pdev->dev, "pump_transfers: flush failed\n");
		message->status = -EIO;
		bfin_spi_giveback(drv_data);
		return;
	}

	if (transfer->len == 0) {
		/* Move to next transfer of this msg */
		message->state = bfin_spi_next_transfer(drv_data);
		/* Schedule next transfer tasklet */
		tasklet_schedule(&drv_data->pump_transfers);
		return;
	}

	if (transfer->tx_buf != NULL) {
		drv_data->tx = (void *)transfer->tx_buf;
		drv_data->tx_end = drv_data->tx + transfer->len;
		dev_dbg(&drv_data->pdev->dev, "tx_buf is %p, tx_end is %p\n",
			transfer->tx_buf, drv_data->tx_end);
	} else {
		drv_data->tx = NULL;
	}

	if (transfer->rx_buf != NULL) {
		full_duplex = transfer->tx_buf != NULL;
		drv_data->rx = transfer->rx_buf;
		drv_data->rx_end = drv_data->rx + transfer->len;
		dev_dbg(&drv_data->pdev->dev, "rx_buf is %p, rx_end is %p\n",
			transfer->rx_buf, drv_data->rx_end);
	} else {
		drv_data->rx = NULL;
	}

	drv_data->rx_dma = transfer->rx_dma;
	drv_data->tx_dma = transfer->tx_dma;
	drv_data->len_in_bytes = transfer->len;
	drv_data->cs_change = transfer->cs_change;

	/* Bits per word setup */
	bits_per_word = transfer->bits_per_word;
	if (bits_per_word == 16) {
		drv_data->n_bytes = bits_per_word/8;
		drv_data->len = (transfer->len) >> 1;
		cr_width = BIT_CTL_WORDSIZE;
		drv_data->ops = &bfin_bfin_spi_transfer_ops_u16;
	} else if (bits_per_word == 8) {
		drv_data->n_bytes = bits_per_word/8;
		drv_data->len = transfer->len;
		cr_width = 0;
		drv_data->ops = &bfin_bfin_spi_transfer_ops_u8;
	}
	cr = bfin_read(&drv_data->regs->ctl) & ~(BIT_CTL_TIMOD | BIT_CTL_WORDSIZE);
	cr |= cr_width;
	bfin_write(&drv_data->regs->ctl, cr);

	dev_dbg(&drv_data->pdev->dev,
		"transfer: drv_data->ops is %p, chip->ops is %p, u8_ops is %p\n",
		drv_data->ops, chip->ops, &bfin_bfin_spi_transfer_ops_u8);

	message->state = RUNNING_STATE;
	dma_config = 0;

	/* Speed setup (surely valid because already checked) */
	if (transfer->speed_hz)
		bfin_write(&drv_data->regs->baud, hz_to_spi_baud(transfer->speed_hz));
	else
		bfin_write(&drv_data->regs->baud, chip->baud);

	bfin_write(&drv_data->regs->stat, BIT_STAT_CLR);
	bfin_spi_cs_active(drv_data, chip);

	dev_dbg(&drv_data->pdev->dev,
		"now pumping a transfer: width is %d, len is %d\n",
		cr_width, transfer->len);

	/*
	 * Try to map dma buffer and do a dma transfer.  If successful use,
	 * different way to r/w according to the enable_dma settings and if
	 * we are not doing a full duplex transfer (since the hardware does
	 * not support full duplex DMA transfers).
	 */
	if (!full_duplex && drv_data->cur_chip->enable_dma
				&& drv_data->len > 6) {

		unsigned long dma_start_addr, flags;

		disable_dma(drv_data->dma_channel);
		clear_dma_irqstat(drv_data->dma_channel);

		/* config dma channel */
		dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n");
		set_dma_x_count(drv_data->dma_channel, drv_data->len);
		if (cr_width == BIT_CTL_WORDSIZE) {
			set_dma_x_modify(drv_data->dma_channel, 2);
			dma_width = WDSIZE_16;
		} else {
			set_dma_x_modify(drv_data->dma_channel, 1);
			dma_width = WDSIZE_8;
		}

		/* poll for SPI completion before start */
		while (!(bfin_read(&drv_data->regs->stat) & BIT_STAT_SPIF))
			cpu_relax();

		/* dirty hack for autobuffer DMA mode */
		if (drv_data->tx_dma == 0xFFFF) {
			dev_dbg(&drv_data->pdev->dev,
				"doing autobuffer DMA out.\n");

			/* no irq in autobuffer mode */
			dma_config =
			    (DMAFLOW_AUTO | RESTART | dma_width | DI_EN);
			set_dma_config(drv_data->dma_channel, dma_config);
			set_dma_start_addr(drv_data->dma_channel,
					(unsigned long)drv_data->tx);
			enable_dma(drv_data->dma_channel);

			/* start SPI transfer */
			bfin_write(&drv_data->regs->ctl, cr | BIT_CTL_TIMOD_DMA_TX);

			/* just return here, there can only be one transfer
			 * in this mode
			 */
			message->status = 0;
			bfin_spi_giveback(drv_data);
			return;
		}

		/* In dma mode, rx or tx must be NULL in one transfer */
		dma_config = (RESTART | dma_width | DI_EN);
		if (drv_data->rx != NULL) {
			/* set transfer mode, and enable SPI */
			dev_dbg(&drv_data->pdev->dev, "doing DMA in to %p (size %zx)\n",
				drv_data->rx, drv_data->len_in_bytes);

			/* invalidate caches, if needed */
			if (bfin_addr_dcacheable((unsigned long) drv_data->rx))
				invalidate_dcache_range((unsigned long) drv_data->rx,
							(unsigned long) (drv_data->rx +
							drv_data->len_in_bytes));

			dma_config |= WNR;
			dma_start_addr = (unsigned long)drv_data->rx;
			cr |= BIT_CTL_TIMOD_DMA_RX | BIT_CTL_SENDOPT;

		} else if (drv_data->tx != NULL) {
			dev_dbg(&drv_data->pdev->dev, "doing DMA out.\n");

			/* flush caches, if needed */
			if (bfin_addr_dcacheable((unsigned long) drv_data->tx))
				flush_dcache_range((unsigned long) drv_data->tx,
						(unsigned long) (drv_data->tx +
						drv_data->len_in_bytes));

			dma_start_addr = (unsigned long)drv_data->tx;
			cr |= BIT_CTL_TIMOD_DMA_TX;

		} else
			BUG();

		/* oh man, here there be monsters ... and i dont mean the
		 * fluffy cute ones from pixar, i mean the kind that'll eat
		 * your data, kick your dog, and love it all.  do *not* try
		 * and change these lines unless you (1) heavily test DMA
		 * with SPI flashes on a loaded system (e.g. ping floods),
		 * (2) know just how broken the DMA engine interaction with
		 * the SPI peripheral is, and (3) have someone else to blame
		 * when you screw it all up anyways.
		 */
		set_dma_start_addr(drv_data->dma_channel, dma_start_addr);
		set_dma_config(drv_data->dma_channel, dma_config);
		local_irq_save(flags);
		SSYNC();
		bfin_write(&drv_data->regs->ctl, cr);
		enable_dma(drv_data->dma_channel);
		dma_enable_irq(drv_data->dma_channel);
		local_irq_restore(flags);

		return;
	}

	/*
	 * We always use SPI_WRITE mode (transfer starts with TDBR write).
	 * SPI_READ mode (transfer starts with RDBR read) seems to have
	 * problems with setting up the output value in TDBR prior to the
	 * start of the transfer.
	 */
	bfin_write(&drv_data->regs->ctl, cr | BIT_CTL_TXMOD);

	if (chip->pio_interrupt) {
		/* SPI irq should have been disabled by now */

		/* discard old RX data and clear RXS */
		bfin_spi_dummy_read(drv_data);

		/* start transfer */
		if (drv_data->tx == NULL)
			bfin_write(&drv_data->regs->tdbr, chip->idle_tx_val);
		else {
			int loop;
			if (bits_per_word == 16) {
				u16 *buf = (u16 *)drv_data->tx;
				for (loop = 0; loop < bits_per_word / 16;
						loop++) {
					bfin_write(&drv_data->regs->tdbr, *buf++);
				}
			} else if (bits_per_word == 8) {
				u8 *buf = (u8 *)drv_data->tx;
				for (loop = 0; loop < bits_per_word / 8; loop++)
					bfin_write(&drv_data->regs->tdbr, *buf++);
			}

			drv_data->tx += drv_data->n_bytes;
		}

		/* once TDBR is empty, interrupt is triggered */
		enable_irq(drv_data->spi_irq);
		return;
	}

	/* IO mode */
	dev_dbg(&drv_data->pdev->dev, "doing IO transfer\n");

	if (full_duplex) {
		/* full duplex mode */
		BUG_ON((drv_data->tx_end - drv_data->tx) !=
		       (drv_data->rx_end - drv_data->rx));
		dev_dbg(&drv_data->pdev->dev,
			"IO duplex: cr is 0x%x\n", cr);

		drv_data->ops->duplex(drv_data);

		if (drv_data->tx != drv_data->tx_end)
			tranf_success = 0;
	} else if (drv_data->tx != NULL) {
		/* write only half duplex */
		dev_dbg(&drv_data->pdev->dev,
			"IO write: cr is 0x%x\n", cr);

		drv_data->ops->write(drv_data);

		if (drv_data->tx != drv_data->tx_end)
			tranf_success = 0;
	} else if (drv_data->rx != NULL) {
		/* read only half duplex */
		dev_dbg(&drv_data->pdev->dev,
			"IO read: cr is 0x%x\n", cr);

		drv_data->ops->read(drv_data);
		if (drv_data->rx != drv_data->rx_end)
			tranf_success = 0;
	}

	if (!tranf_success) {
		dev_dbg(&drv_data->pdev->dev,
			"IO write error!\n");
		message->state = ERROR_STATE;
	} else {
		/* Update total byte transferred */
		message->actual_length += drv_data->len_in_bytes;
		/* Move to next transfer of this msg */
		message->state = bfin_spi_next_transfer(drv_data);
		if (drv_data->cs_change && message->state != DONE_STATE) {
			bfin_spi_flush(drv_data);
			bfin_spi_cs_deactive(drv_data, chip);
		}
	}

	/* Schedule next transfer tasklet */
	tasklet_schedule(&drv_data->pump_transfers);
}

/* pop a msg from queue and kick off real transfer */
static void bfin_spi_pump_messages(struct work_struct *work)
{
	struct bfin_spi_master_data *drv_data;
	unsigned long flags;

	drv_data = container_of(work, struct bfin_spi_master_data, pump_messages);

	/* Lock queue and check for queue work */
	spin_lock_irqsave(&drv_data->lock, flags);
	if (list_empty(&drv_data->queue) || !drv_data->running) {
		/* pumper kicked off but no work to do */
		drv_data->busy = 0;
		spin_unlock_irqrestore(&drv_data->lock, flags);
		return;
	}

	/* Make sure we are not already running a message */
	if (drv_data->cur_msg) {
		spin_unlock_irqrestore(&drv_data->lock, flags);
		return;
	}

	/* Extract head of queue */
	drv_data->cur_msg = list_entry(drv_data->queue.next,
				       struct spi_message, queue);

	/* Setup the SSP using the per chip configuration */
	drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
	bfin_spi_restore_state(drv_data);

	list_del_init(&drv_data->cur_msg->queue);

	/* Initial message state */
	drv_data->cur_msg->state = START_STATE;
	drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
					    struct spi_transfer, transfer_list);

	dev_dbg(&drv_data->pdev->dev,
		"got a message to pump, state is set to: baud "
		"%d, flag 0x%x, ctl 0x%x\n",
		drv_data->cur_chip->baud, drv_data->cur_chip->flag,
		drv_data->cur_chip->ctl_reg);

	dev_dbg(&drv_data->pdev->dev,
		"the first transfer len is %d\n",
		drv_data->cur_transfer->len);

	/* Mark as busy and launch transfers */
	tasklet_schedule(&drv_data->pump_transfers);

	drv_data->busy = 1;
	spin_unlock_irqrestore(&drv_data->lock, flags);
}

/*
 * got a msg to transfer, queue it in drv_data->queue.
 * And kick off message pumper
 */
static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
{
	struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
	unsigned long flags;

	spin_lock_irqsave(&drv_data->lock, flags);

	if (!drv_data->running) {
		spin_unlock_irqrestore(&drv_data->lock, flags);
		return -ESHUTDOWN;
	}

	msg->actual_length = 0;
	msg->status = -EINPROGRESS;
	msg->state = START_STATE;

	dev_dbg(&spi->dev, "adding an msg in transfer() \n");
	list_add_tail(&msg->queue, &drv_data->queue);

	if (drv_data->running && !drv_data->busy)
		queue_work(drv_data->workqueue, &drv_data->pump_messages);

	spin_unlock_irqrestore(&drv_data->lock, flags);

	return 0;
}

#define MAX_SPI_SSEL	7

static const u16 ssel[][MAX_SPI_SSEL] = {
	{P_SPI0_SSEL1, P_SPI0_SSEL2, P_SPI0_SSEL3,
	P_SPI0_SSEL4, P_SPI0_SSEL5,
	P_SPI0_SSEL6, P_SPI0_SSEL7},

	{P_SPI1_SSEL1, P_SPI1_SSEL2, P_SPI1_SSEL3,
	P_SPI1_SSEL4, P_SPI1_SSEL5,
	P_SPI1_SSEL6, P_SPI1_SSEL7},

	{P_SPI2_SSEL1, P_SPI2_SSEL2, P_SPI2_SSEL3,
	P_SPI2_SSEL4, P_SPI2_SSEL5,
	P_SPI2_SSEL6, P_SPI2_SSEL7},
};

/* setup for devices (may be called multiple times -- not just first setup) */
static int bfin_spi_setup(struct spi_device *spi)
{
	struct bfin5xx_spi_chip *chip_info;
	struct bfin_spi_slave_data *chip = NULL;
	struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
	u16 bfin_ctl_reg;
	int ret = -EINVAL;

	/* Only alloc (or use chip_info) on first setup */
	chip_info = NULL;
	chip = spi_get_ctldata(spi);
	if (chip == NULL) {
		chip = kzalloc(sizeof(*chip), GFP_KERNEL);
		if (!chip) {
			dev_err(&spi->dev, "cannot allocate chip data\n");
			ret = -ENOMEM;
			goto error;
		}

		chip->enable_dma = 0;
		chip_info = spi->controller_data;
	}

	/* Let people set non-standard bits directly */
	bfin_ctl_reg = BIT_CTL_OPENDRAIN | BIT_CTL_EMISO |
		BIT_CTL_PSSE | BIT_CTL_GM | BIT_CTL_SZ;

	/* chip_info isn't always needed */
	if (chip_info) {
		/* Make sure people stop trying to set fields via ctl_reg
		 * when they should actually be using common SPI framework.
		 * Currently we let through: WOM EMISO PSSE GM SZ.
		 * Not sure if a user actually needs/uses any of these,
		 * but let's assume (for now) they do.
		 */
		if (chip_info->ctl_reg & ~bfin_ctl_reg) {
			dev_err(&spi->dev,
				"do not set bits in ctl_reg that the SPI framework manages\n");
			goto error;
		}
		chip->enable_dma = chip_info->enable_dma != 0
		    && drv_data->master_info->enable_dma;
		chip->ctl_reg = chip_info->ctl_reg;
		chip->cs_chg_udelay = chip_info->cs_chg_udelay;
		chip->idle_tx_val = chip_info->idle_tx_val;
		chip->pio_interrupt = chip_info->pio_interrupt;
	} else {
		/* force a default base state */
		chip->ctl_reg &= bfin_ctl_reg;
	}

	/* translate common spi framework into our register */
	if (spi->mode & ~(SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST)) {
		dev_err(&spi->dev, "unsupported spi modes detected\n");
		goto error;
	}
	if (spi->mode & SPI_CPOL)
		chip->ctl_reg |= BIT_CTL_CPOL;
	if (spi->mode & SPI_CPHA)
		chip->ctl_reg |= BIT_CTL_CPHA;
	if (spi->mode & SPI_LSB_FIRST)
		chip->ctl_reg |= BIT_CTL_LSBF;
	/* we dont support running in slave mode (yet?) */
	chip->ctl_reg |= BIT_CTL_MASTER;

	/*
	 * Notice: for blackfin, the speed_hz is the value of register
	 * SPI_BAUD, not the real baudrate
	 */
	chip->baud = hz_to_spi_baud(spi->max_speed_hz);
	chip->chip_select_num = spi->chip_select;
	if (chip->chip_select_num < MAX_CTRL_CS) {
		if (!(spi->mode & SPI_CPHA))
			dev_warn(&spi->dev,
				"Warning: SPI CPHA not set: Slave Select not under software control!\n"
				"See Documentation/blackfin/bfin-spi-notes.txt\n");

		chip->flag = (1 << spi->chip_select) << 8;
	} else
		chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;

	if (chip->enable_dma && chip->pio_interrupt) {
		dev_err(&spi->dev,
			"enable_dma is set, do not set pio_interrupt\n");
		goto error;
	}
	/*
	 * if any one SPI chip is registered and wants DMA, request the
	 * DMA channel for it
	 */
	if (chip->enable_dma && !drv_data->dma_requested) {
		/* register dma irq handler */
		ret = request_dma(drv_data->dma_channel, "BFIN_SPI_DMA");
		if (ret) {
			dev_err(&spi->dev,
				"Unable to request BlackFin SPI DMA channel\n");
			goto error;
		}
		drv_data->dma_requested = 1;

		ret = set_dma_callback(drv_data->dma_channel,
			bfin_spi_dma_irq_handler, drv_data);
		if (ret) {
			dev_err(&spi->dev, "Unable to set dma callback\n");
			goto error;
		}
		dma_disable_irq(drv_data->dma_channel);
	}

	if (chip->pio_interrupt && !drv_data->irq_requested) {
		ret = request_irq(drv_data->spi_irq, bfin_spi_pio_irq_handler,
			0, "BFIN_SPI", drv_data);
		if (ret) {
			dev_err(&spi->dev, "Unable to register spi IRQ\n");
			goto error;
		}
		drv_data->irq_requested = 1;
		/* we use write mode, spi irq has to be disabled here */
		disable_irq(drv_data->spi_irq);
	}

	if (chip->chip_select_num >= MAX_CTRL_CS) {
		/* Only request on first setup */
		if (spi_get_ctldata(spi) == NULL) {
			ret = gpio_request(chip->cs_gpio, spi->modalias);
			if (ret) {
				dev_err(&spi->dev, "gpio_request() error\n");
				goto pin_error;
			}
			gpio_direction_output(chip->cs_gpio, 1);
		}
	}

	dev_dbg(&spi->dev, "setup spi chip %s, width is %d, dma is %d\n",
			spi->modalias, spi->bits_per_word, chip->enable_dma);
	dev_dbg(&spi->dev, "ctl_reg is 0x%x, flag_reg is 0x%x\n",
			chip->ctl_reg, chip->flag);

	spi_set_ctldata(spi, chip);

	dev_dbg(&spi->dev, "chip select number is %d\n", chip->chip_select_num);
	if (chip->chip_select_num < MAX_CTRL_CS) {
		ret = peripheral_request(ssel[spi->master->bus_num]
		                         [chip->chip_select_num-1], spi->modalias);
		if (ret) {
			dev_err(&spi->dev, "peripheral_request() error\n");
			goto pin_error;
		}
	}

	bfin_spi_cs_enable(drv_data, chip);
	bfin_spi_cs_deactive(drv_data, chip);

	return 0;

 pin_error:
	if (chip->chip_select_num >= MAX_CTRL_CS)
		gpio_free(chip->cs_gpio);
	else
		peripheral_free(ssel[spi->master->bus_num]
			[chip->chip_select_num - 1]);
 error:
	if (chip) {
		if (drv_data->dma_requested)
			free_dma(drv_data->dma_channel);
		drv_data->dma_requested = 0;

		kfree(chip);
		/* prevent free 'chip' twice */
		spi_set_ctldata(spi, NULL);
	}

	return ret;
}

/*
 * callback for spi framework.
 * clean driver specific data
 */
static void bfin_spi_cleanup(struct spi_device *spi)
{
	struct bfin_spi_slave_data *chip = spi_get_ctldata(spi);
	struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);

	if (!chip)
		return;

	if (chip->chip_select_num < MAX_CTRL_CS) {
		peripheral_free(ssel[spi->master->bus_num]
					[chip->chip_select_num-1]);
		bfin_spi_cs_disable(drv_data, chip);
	} else
		gpio_free(chip->cs_gpio);

	kfree(chip);
	/* prevent free 'chip' twice */
	spi_set_ctldata(spi, NULL);
}

static int bfin_spi_init_queue(struct bfin_spi_master_data *drv_data)
{
	INIT_LIST_HEAD(&drv_data->queue);
	spin_lock_init(&drv_data->lock);

	drv_data->running = false;
	drv_data->busy = 0;

	/* init transfer tasklet */
	tasklet_init(&drv_data->pump_transfers,
		     bfin_spi_pump_transfers, (unsigned long)drv_data);

	/* init messages workqueue */
	INIT_WORK(&drv_data->pump_messages, bfin_spi_pump_messages);
	drv_data->workqueue = create_singlethread_workqueue(
				dev_name(drv_data->master->dev.parent));
	if (drv_data->workqueue == NULL)
		return -EBUSY;

	return 0;
}

static int bfin_spi_start_queue(struct bfin_spi_master_data *drv_data)
{
	unsigned long flags;

	spin_lock_irqsave(&drv_data->lock, flags);

	if (drv_data->running || drv_data->busy) {
		spin_unlock_irqrestore(&drv_data->lock, flags);
		return -EBUSY;
	}

	drv_data->running = true;
	drv_data->cur_msg = NULL;
	drv_data->cur_transfer = NULL;
	drv_data->cur_chip = NULL;
	spin_unlock_irqrestore(&drv_data->lock, flags);

	queue_work(drv_data->workqueue, &drv_data->pump_messages);

	return 0;
}

static int bfin_spi_stop_queue(struct bfin_spi_master_data *drv_data)
{
	unsigned long flags;
	unsigned limit = 500;
	int status = 0;

	spin_lock_irqsave(&drv_data->lock, flags);

	/*
	 * This is a bit lame, but is optimized for the common execution path.
	 * A wait_queue on the drv_data->busy could be used, but then the common
	 * execution path (pump_messages) would be required to call wake_up or
	 * friends on every SPI message. Do this instead
	 */
	drv_data->running = false;
	while ((!list_empty(&drv_data->queue) || drv_data->busy) && limit--) {
		spin_unlock_irqrestore(&drv_data->lock, flags);
		msleep(10);
		spin_lock_irqsave(&drv_data->lock, flags);
	}

	if (!list_empty(&drv_data->queue) || drv_data->busy)
		status = -EBUSY;

	spin_unlock_irqrestore(&drv_data->lock, flags);

	return status;
}

static int bfin_spi_destroy_queue(struct bfin_spi_master_data *drv_data)
{
	int status;

	status = bfin_spi_stop_queue(drv_data);
	if (status != 0)
		return status;

	destroy_workqueue(drv_data->workqueue);

	return 0;
}

static int bfin_spi_probe(struct platform_device *pdev)
{
	struct device *dev = &pdev->dev;
	struct bfin5xx_spi_master *platform_info;
	struct spi_master *master;
	struct bfin_spi_master_data *drv_data;
	struct resource *res;
	int status = 0;

	platform_info = dev_get_platdata(dev);

	/* Allocate master with space for drv_data */
	master = spi_alloc_master(dev, sizeof(*drv_data));
	if (!master) {
		dev_err(&pdev->dev, "can not alloc spi_master\n");
		return -ENOMEM;
	}

	drv_data = spi_master_get_devdata(master);
	drv_data->master = master;
	drv_data->master_info = platform_info;
	drv_data->pdev = pdev;
	drv_data->pin_req = platform_info->pin_req;

	/* the spi->mode bits supported by this driver: */
	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST;
	master->bits_per_word_mask = SPI_BPW_MASK(8) | SPI_BPW_MASK(16);
	master->bus_num = pdev->id;
	master->num_chipselect = platform_info->num_chipselect;
	master->cleanup = bfin_spi_cleanup;
	master->setup = bfin_spi_setup;
	master->transfer = bfin_spi_transfer;

	/* Find and map our resources */
	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (res == NULL) {
		dev_err(dev, "Cannot get IORESOURCE_MEM\n");
		status = -ENOENT;
		goto out_error_get_res;
	}

	drv_data->regs = ioremap(res->start, resource_size(res));
	if (drv_data->regs == NULL) {
		dev_err(dev, "Cannot map IO\n");
		status = -ENXIO;
		goto out_error_ioremap;
	}

	res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
	if (res == NULL) {
		dev_err(dev, "No DMA channel specified\n");
		status = -ENOENT;
		goto out_error_free_io;
	}
	drv_data->dma_channel = res->start;

	drv_data->spi_irq = platform_get_irq(pdev, 0);
	if (drv_data->spi_irq < 0) {
		dev_err(dev, "No spi pio irq specified\n");
		status = -ENOENT;
		goto out_error_free_io;
	}

	/* Initial and start queue */
	status = bfin_spi_init_queue(drv_data);
	if (status != 0) {
		dev_err(dev, "problem initializing queue\n");
		goto out_error_queue_alloc;
	}

	status = bfin_spi_start_queue(drv_data);
	if (status != 0) {
		dev_err(dev, "problem starting queue\n");
		goto out_error_queue_alloc;
	}

	status = peripheral_request_list(drv_data->pin_req, DRV_NAME);
	if (status != 0) {
		dev_err(&pdev->dev, ": Requesting Peripherals failed\n");
		goto out_error_queue_alloc;
	}

	/* Reset SPI registers. If these registers were used by the boot loader,
	 * the sky may fall on your head if you enable the dma controller.
	 */
	bfin_write(&drv_data->regs->ctl, BIT_CTL_CPHA | BIT_CTL_MASTER);
	bfin_write(&drv_data->regs->flg, 0xFF00);

	/* Register with the SPI framework */
	platform_set_drvdata(pdev, drv_data);
	status = spi_register_master(master);
	if (status != 0) {
		dev_err(dev, "problem registering spi master\n");
		goto out_error_queue_alloc;
	}

	dev_info(dev, "%s, Version %s, regs@%p, dma channel@%d\n",
		DRV_DESC, DRV_VERSION, drv_data->regs,
		drv_data->dma_channel);
	return status;

out_error_queue_alloc:
	bfin_spi_destroy_queue(drv_data);
out_error_free_io:
	iounmap(drv_data->regs);
out_error_ioremap:
out_error_get_res:
	spi_master_put(master);

	return status;
}

/* stop hardware and remove the driver */
static int bfin_spi_remove(struct platform_device *pdev)
{
	struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
	int status = 0;

	if (!drv_data)
		return 0;

	/* Remove the queue */
	status = bfin_spi_destroy_queue(drv_data);
	if (status != 0)
		return status;

	/* Disable the SSP at the peripheral and SOC level */
	bfin_spi_disable(drv_data);

	/* Release DMA */
	if (drv_data->master_info->enable_dma) {
		if (dma_channel_active(drv_data->dma_channel))
			free_dma(drv_data->dma_channel);
	}

	if (drv_data->irq_requested) {
		free_irq(drv_data->spi_irq, drv_data);
		drv_data->irq_requested = 0;
	}

	/* Disconnect from the SPI framework */
	spi_unregister_master(drv_data->master);

	peripheral_free_list(drv_data->pin_req);

	return 0;
}

#ifdef CONFIG_PM_SLEEP
static int bfin_spi_suspend(struct device *dev)
{
	struct bfin_spi_master_data *drv_data = dev_get_drvdata(dev);
	int status = 0;

	status = bfin_spi_stop_queue(drv_data);
	if (status != 0)
		return status;

	drv_data->ctrl_reg = bfin_read(&drv_data->regs->ctl);
	drv_data->flag_reg = bfin_read(&drv_data->regs->flg);

	/*
	 * reset SPI_CTL and SPI_FLG registers
	 */
	bfin_write(&drv_data->regs->ctl, BIT_CTL_CPHA | BIT_CTL_MASTER);
	bfin_write(&drv_data->regs->flg, 0xFF00);

	return 0;
}

static int bfin_spi_resume(struct device *dev)
{
	struct bfin_spi_master_data *drv_data = dev_get_drvdata(dev);
	int status = 0;

	bfin_write(&drv_data->regs->ctl, drv_data->ctrl_reg);
	bfin_write(&drv_data->regs->flg, drv_data->flag_reg);

	/* Start the queue running */
	status = bfin_spi_start_queue(drv_data);
	if (status != 0) {
		dev_err(dev, "problem starting queue (%d)\n", status);
		return status;
	}

	return 0;
}

static SIMPLE_DEV_PM_OPS(bfin_spi_pm_ops, bfin_spi_suspend, bfin_spi_resume);

#define BFIN_SPI_PM_OPS		(&bfin_spi_pm_ops)
#else
#define BFIN_SPI_PM_OPS		NULL
#endif

MODULE_ALIAS("platform:bfin-spi");
static struct platform_driver bfin_spi_driver = {
	.driver	= {
		.name	= DRV_NAME,
		.owner	= THIS_MODULE,
		.pm	= BFIN_SPI_PM_OPS,
	},
	.probe		= bfin_spi_probe,
	.remove		= bfin_spi_remove,
};

static int __init bfin_spi_init(void)
{
	return platform_driver_register(&bfin_spi_driver);
}
subsys_initcall(bfin_spi_init);

static void __exit bfin_spi_exit(void)
{
	platform_driver_unregister(&bfin_spi_driver);
}
module_exit(bfin_spi_exit);