23 Jun, 2011
1 commit
22 Jun, 2011
2 commits
-
When the connection is ready we should set the connection
to CONNECTED so userspace can use it.Signed-off-by: Vinicius Costa Gomes
Signed-off-by: Gustavo F. Padovan -
Conflicts:
net/bluetooth/l2cap_core.c
21 Jun, 2011
18 commits
-
These are a potential source of confusion, as most C code treats all
non-zero values as true.Signed-off-by: Mike McCormack
Acked-by: Larry Finger
Signed-off-by: John W. Linville -
rtl_ps_set_rf_state's protect_or_not parameter is not set to
true anywhere, except for commented out code.It enables some legacy locking code, which is no longer used,
so delete the parameter and the old locking code.Signed-off-by: Mike McCormack
Acked-by: Larry Finger
Signed-off-by: John W. Linville -
offchan_deley should be offchan_delay
Signed-off-by: Mike McCormack
Acked-by: Larry Finger
Signed-off-by: John W. Linville -
Function managing IRQs is needed for external drivers like b43.
On the other side we do not expect writing any hosts drivers outside of
bcma, so this is safe to do not export functions related to this.Signed-off-by: Rafał Miłecki
Signed-off-by: John W. Linville -
Signed-off-by: Pavel Roskin
Signed-off-by: John W. Linville -
Nothing else is freeing it, and this mirrors the error handling path
already in ath5k_init_softc.https://bugzilla.kernel.org/show_bug.cgi?id=37592
Signed-off-by: John W. Linville
Reported-by: Tsyvarev Andrey -
Signed-off-by: Rafał Miłecki
Signed-off-by: John W. Linville -
Signed-off-by: Rafał Miłecki
Signed-off-by: John W. Linville -
checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Cc: kmuthusa@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan
Signed-off-by: John W. Linville -
when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHzSigned-off-by: Mohammed Shafi Shajakhan
Signed-off-by: John W. Linville -
Cancel all relevant timers/works before suspending (wowlan).
This patch handles the following warning:
WARNING: at net/mac80211/util.c:565 queueing ieee80211 work while going to suspend
Backtrace:
[] (ieee80211_can_queue_work+0x0/0x4c [mac80211])
[] (ieee80211_queue_work+0x0/0x30 [mac80211])
[] (ieee80211_sta_timer+0x0/0x3c [mac80211])
[] (run_timer_softirq+0x0/0x220)
[] (__do_softirq+0x0/0x130)
[] (irq_exit+0x0/0xb4)
[] (ipi_timer+0x0/0x4c)
[] (do_local_timer+0x0/0x88)
[] (cpu_idle+0x0/0xe0)
[] (rest_init+0x0/0xe0)
[] (start_kernel+0x0/0x314)Signed-off-by: Eliad Peller
Signed-off-by: John W. Linville -
We already have access to the chan, we don't have to access the
socket to get its imtu.Signed-off-by: Vinicius Costa Gomes
Signed-off-by: Gustavo F. Padovan -
We should not try to do any other type of configuration for
LE links when they become ready.Signed-off-by: Vinicius Costa Gomes
Signed-off-by: Gustavo F. Padovan -
…t/iwlwifi/iwlwifi-2.6
-
core.h references ieee80211_ops but doesn't include mac80211.h, which issues
a warning once mac80211-compat.h is taken into use.Acked-by: Larry Finger
Signed-off-by: Kalle Valo
Signed-off-by: John W. Linville -
zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.Signed-off-by: Kalle Valo
Signed-off-by: John W. Linville -
The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.Signed-off-by: Kalle Valo
Signed-off-by: John W. Linville -
The hacks break once mac80211-compat.h is taken into use. Fix it by adding
an ifdef check.Signed-off-by: Kalle Valo
Signed-off-by: John W. Linville
18 Jun, 2011
19 commits
-
Remove unused and incorrect EEPROM define
Signed-off-by: Wey-Yi Guy
-
Same operation needed by multiple devices, move to single function.
Signed-off-by: Wey-Yi Guy
-
Code alignment, no functional changes.
Signed-off-by: Wey-Yi Guy
-
Add offset define for subsystem id in EEPROM
Signed-off-by: Wey-Yi Guy
-
Add power_level module parameter to set the default power save level.
Power save level has range from 1 - 5, default power save level is 1.Signed-off-by: Wey-Yi Guy
-
Add power_save module parameter to enable power management if needed
Default power management is disabled.Signed-off-by: Wey-Yi Guy
-
Since the irq number is just an unsigned int, store it inside iwl_bus
instead of calling the get_irq ops every time it is needed.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Since there is no protection around SYNC host command mechanism, at least WARN
when collision happens between two SYNC host comamnds. I am not sure there is a
real issue (beyond the HCMD_ACTIVE flag maintenance) with having two SYNC host
commands at the same time, but at least now, we will know about it.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
All pci related stuff is in iwl-pci.c.
Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
In order to remove a few more dereference to priv->pdev that will be killed
[Asoon, there is now a method to get the IRQ number.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
The PCI_REVISION_ID is read and printed in iwl_pci_probe anyway using pr_info
Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Continue to popule the PCI layer and the iwl_bus_ops with the power related
stuff.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Get a pointer to the struct device during probe and get the rid of all the PCI
specific DMA wrappers.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Since we have now a PCI layer, all the init and deinit code that is PCI
related should move to there.Also move the IO functions: read8/read32/write32. They need hw_base which
is killed from priv.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
Bus specific layer must know how to return the struct device* of the device.
Implement that as a callback of iwl_bus_ops and use that callback instead of
using the priv->pdev pointer which is meant to disappear soon.Since the struct device * is needed in hot path, iwl_bus holds a pointer to it
instead of calling get_dev all the time.Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy -
iwl_bus will represent a bus, and iwl_bus_ops all the operations that can be
done on this bus.
For the moment only set_prv_data is implemented. More to come...Signed-off-by: Emmanuel Grumbach
Signed-off-by: Wey-Yi Guy
