14 Jun, 2007
3 commits
-
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: move input-polldev to drivers/input
Input: i8042 - add ULI EV4873 to noloop list
Input: i8042 - add ASUS P65UP5 to the noloop list
Input: usbtouchscreen - fix fallout caused by move from drivers/usb -
Somehow the code to read the read-only switch of SD cards got lost
in the reorganisation.Signed-off-by: Pierre Ossman
-
Ignoring OMAP_MMC_STAT_CARD_ERR, treating it as if the command
completed correctly.Signed-off-by: Ragner Magalhaes
Signed-off-by: Carlos Eduardo Aguiar
Signed-off-by: Pierre Ossman
13 Jun, 2007
13 commits
-
To work around deficiences in Kconfig that allows to "select"
a symbol without automatically selecting all dependencies for
that symbol move input-polldev from drivers/input/misc to
drivers/input thus removing extra dependency on CONFIG_INPUT_MISC.Signed-off-by: Dmitry Torokhov
-
…inville/wireless-2.6 into upstream-fixes
-
…e/wireless-2.6 into upstream-fixes
-
Update myri10ge driver version to 1.3.1-1.248.
Signed-off-by: Brice Goglin
Signed-off-by: Jeff Garzik -
Since Myri-10G boards may also run in Myrinet mode instead of Ethernet,
add a message when we detect that the link partner is not running in the
right mode.Signed-off-by: Brice Goglin
Signed-off-by: Jeff Garzik -
Limit the number of recoveries from a NIC hw watchdog reset to 1 by default.
It enables detection of defective NICs immediately since these memory parity
errors are expected to happen very rarely (less than once per century*NIC).Signed-off-by: Brice Goglin
Signed-off-by: Jeff Garzik -
NetXen: Fix incorrect link status even with switch turned OFF.
NetXen driver failed to accurately indicate when a link is up or down.
This was encountered during failover testing, when the first port
indicated that the link was up even when the 10G switch it was assigned
to in the Bladecenter was turned off completely.Signed-off by: Wen Xiong
Signed-off by: Mithlesh ThukralSigned-off-by: Jeff Garzik
-
This reverts commit d52df4a35af569071fda3f4eb08e47cc7023f094.
This patch attempted to fix e100 for non-cache coherent memory
architectures by using the cb style code that eepro100 had and using
the EL and s bits from the RFD list. Unfortunately the hardware
doesn't work exactly like this and therefore this patch actually
breaks e100. Reverting the change brings it back to the previously
known good state for 2.6.22. The pending rewrite in progress to this
code can then be safely merged later.Signed-off-by: Auke Kok
Signed-off-by: Jeff Garzik -
With firmware 5.220.11.p5, this allows to specify the anycast addresses the
device will listen to.The anycast address range is C0:27:C0:27:C0:XX where XX goes from 00 to 1F (or
0 to 31 in dec). The value to write on anycast_mask will specify which
addresses the device listens to. Bits in a 32 bit int are numbered from 0
(least significative bit) to 31. A specific address ending in YY will be
listened to if bit YY in the value is set to one.Examples:
0x00000000 : do not listen to any anycast address
0xFFFFFFFF : listen to every anycast address from :00 to :1F
0x00000013 : listen to anycast addresses :00, :01 and :04Signed-off-by: Luis Carlos Cobo
Signed-off-by: John W. Linville -
Found by Luis; got broken during module split.
Signed-off-by: Dan Williams
Signed-off-by: John W. Linville -
This avoids channel mismatch between driver and firmware in case we change
channel while associated to an AP.Signed-off-by: Luis Carlos Cobo Rus
Signed-off-by: John W. Linville -
Signed-off-by: Luis Carlos Cobo Rus
Signed-off-by: John W. Linville
12 Jun, 2007
24 commits
-
The box does not implement AUX LOOP command properly and so we
can't test for AUX IRQ delivery so blacklist it via DMI and
assume that AUX port is present.Signed-off-by: Dmitry Torokhov
-
This board does not raise AUX IRQ in response to AUX LOOP command
which interferes with our test for proper AUX IRQ wiring. Put it
in the blacklist and assume mouse is present.Signed-off-by: Dmitry Torokhov
-
During the move from drivers/usb/input into drivers/input/touchscreen
Kconfig variables were shuffled a bit to use a new namespace
(CONFIG_TOUCHSCREEN) while usbtouchscreen was still using old ones.Also noticed by Robert P. J. Day
Signed-off-by: Ondrej Zary
Signed-off-by: Daniel Ritz
Signed-off-by: Dmitry Torokhov -
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure RQ allocation is always valid
RDMA/cma: Fix initialization of next_port
IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
mlx4_core: Don't set MTT address in dMPT entries with PA set
mlx4_core: Check firmware command interface revision
IB/mthca, mlx4_core: Fix typo in comment
mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
mlx4_core: Initialize ctx_list and ctx_lock earlier
mlx4_core: Fix CQ context layout -
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] intel_agp: Add support for G33, Q33 and Q35 chipsets
[AGPGART] intel_agp: add support for 945GME
[AGPGART] intel_agp: add support for 965GME/GLE
[AGPGART] intel_agp: use table for device probe
[AGPGART] intel_agp: cleanup intel private data -
* 'linus-plus-plus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: limit post SRST nsect/lbal wait to ~100ms
libata: force PIO on IOMEGA ZIP 250 ATAPI
libata passthru: update cached device paramters
libata passthru: always enforce correct DEV bit
libata passthru: map UDMA protocols
libata passthru: support PIO multi commands
libata passthru: update protocol numbers
libata: Correct abuse of language
libata-core/sff: Fix multiple assumptions about DMA
ahci: Add MCP73/MCP77 support to AHCI driver
libata: fix hw_sata_spd_limit initialization
libata: print device model and firmware revision for ATAPI devices
libata: fix probe time irq printouts
libata: disable NCQ for HITACHI HTS541680J9SA00/SB21C7EP
remove unused variable in pata_isapnp -
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (5751): Ivtv: fix ia64 printk format warnings.
V4L/DVB (5761): Fix broken b2c2 dependency on non x86 architectures
V4L/DVB (5673): Fix audio stuttering for saa711x/ivtv when in radio mode.
V4L/DVB (5736): Add V4L2_FBUF_CAP/FLAG_LOCAL/GLOBAL_INV_ALPHA
V4L/DVB (5732): Add ivtv CROPCAP support and fix ivtv S_CROP for video output.
V4L/DVB (5730): Remove unused V4L2_CAP_VIDEO_OUTPUT_POS
V4L/DVB (5720): Usbvision: fix urb allocation and submits
V4L/DVB (5716): Tda10086,tda826x: fix tuning, STR/SNR values
V4L/DVB (5675): Move big PIO accesses from the interrupt handler to a workhandler
V4L/DVB (5699): Cinergyt2: fix file release handler
V4L/DVB (5700): Saa7111: fix picture settings cache bug
V4L/DVB (5702): Fix Kconfig items to avoid linkedition errors -
* master.kernel.org:/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: Add the MCP73/77 support to PATA driver
Add the PATA controller device ID to pci_ids.h for MCP73/MCP77.
hpt366: disallow Ultra133 for HPT374
ide: generic IDE PCI driver, add another device exception
ide: HPA detect from resume
it821x: RAID mode fixes
serverworks: fix CSB6 tuning logic
serverworks: remove crappy code -
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
mmc: don't call switch on old cards
mmc: fix broken if clause
au1xmmc: Replace C code with call to ARRAY_SIZE() macro.
mmc-atmel: remove linux/mmc/protocol.h dependencies -
Kill mixed case function names from scan.c/scan.h.
Signed-off-by: Dan Williams
Signed-off-by: John W. Linville -
Unused.
Signed-off-by: Dan Williams
Signed-off-by: John W. Linville -
Replace WLAN_802_11_SSID with direct 'ssid' and 'ssid_len' members
like ieee80211. In the process, remove private libertas_escape_essid
and depend on the ieee80211 implementation of escape_essid instead.Signed-off-by: Dan Williams
Signed-off-by: John W. Linville -
Signed-off-by: Dan Williams
Signed-off-by: John W. Linville -
Byte-swapping length fields and then passing them to memcpy() considered
harmful.Signed-off-by: David Woodhouse
Signed-off-by: John W. Linville -
Signed-off-by: David Woodhouse
Signed-off-by: John W. Linville -
Now we finally get connectivity. For a while, before something else dies...
Signed-off-by: David Woodhouse
Signed-off-by: John W. Linville -
Now it at least manages to load the firmware.
Signed-off-by: David Woodhouse
Signed-off-by: John W. Linville -
Signed-off-by: David Woodhouse
Signed-off-by: John W. Linville -
Fix various issues reported by sparse.
Signed-off-by: Dan Williams
Signed-off-by: John W. Linville -
Signed-off-by: David Woodhouse
Signed-off-by: John W. Linville -
Signed-off-by: Luis Carlos Cobo Rus
Signed-off-by: John W. Linville -
Separate wireless handlers of mshX and ethX. ethX remains as before.
For mshX, it has been disabled set/get essid, wap and set mode. Get mode always
returns "Repeater" and by now we use the Nickname to show if the mesh is active
("Mesh") or not (empty). The rest remains as before.Signed-off-by: Luis Carlos Cobo Rus
Signed-off-by: John W. Linville -
Signed-off-by: Luis Carlos Cobo Rus
Signed-off-by: John W. Linville -
Fix some wording and blinding table command options, clarify argument list for
fwt_add and fwt_list, simplify fwt_list_routeSigned-off-by: Luis Carlos Cobo Rus
Signed-off-by: John W. Linville
