05 Feb, 2009
3 commits
-
This patch adds ALSA support for the AC97 controller found on Atmel
AVR32 devices.Tested on ATSTK1006 + ATSTK1000 with a development board with a AC97
codec.Signed-off-by: Hans-Christian Egtvedt
Signed-off-by: Takashi Iwai -
This patch adds ALSA support for the Audio Bistream DAC found on Atmel
AVR32 devices. The ABDAC is an Atmel IP which might show up on AT91
devices in the future, hence making a generic driver which can be
utilized by AT91 arch if needed.Datasheet describing the ABDAC peripheral is available in the AT32AP7000
datasheet, http://www.atmel.com/dyn/products/datasheets.asp?family_id=682Tested on ATSTK1006 + ATSTK1000 with a class D amplifier stage.
Signed-off-by: Hans-Christian Egtvedt
Signed-off-by: Takashi Iwai
29 Jan, 2009
3 commits
-
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Fix handling of _PAGE_COHERENT in BAT setup code
powerpc/pseries: Correct VIO bus accounting problem in CMO env.
powerpc: More printing warning fixes for the l64 to ll64 conversion
powerpc: Remove arch/ppc cruft from Kconfig
powerpc: Printing fix for l64 to ll64 conversion: phyp_dump.c
powerpc/embedded6xx: Update defconfigs
powerpc/8xx: Update defconfigs
powerpc/86xx: Update defconfigs
powerpc/83xx: Update defconfigs
powerpc/85xx: Update defconfigs
powerpc/mpc8313erdb: fix kernel panic because mdio device is not probed
powerpc/4xx: Update multi-board PowerPC 4xx defconfigs
powerpc/44x: Update PowerPC 44x defconfigs
powerpc/40x: Update PowerPC 40x defconfigs
powerpc/85xx: Fix typo in mpc8572ds dts
powerpc/44x: Warp patches for the new NDFC driver
powerpc/4xx: DTS: Add Add'l SDRAM0 Compatible and Interrupt Info -
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: fix 5329 ColdFire periphal addressing
uclinux: add process name to allocation error message
m68knommu: correct the mii calculations for 532x ColdFire FEC
m68knommu: add ColdFire M532x to the FEC configuration options
m68knommu: fix syscall restarting
m68knommu: remove the obsolete and long unused comempci chip support
m68knommu: remove the no longer used PCI support option
m68knommu: remove obsolete and unused eLIA board
m68knommu: set NO_DMA
m68knommu: fix cache flushing for the 527x ColdFire processors
m68knommu: fix ColdFire 5272 serial baud rates in mcf.c
m68knommu: use one exist from execption
28 Jan, 2009
34 commits
-
Commit d7b1956fed33d30c4815e848fd7a143722916868 ("DMI: Introduce
dmi_first_match to make the interface more flexible") introduced compile
errors like the following when !CONFIG_DMIdrivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a castWe just need a dummy version of dmi_first_match() to fix this all up.
Signed-off-by: Kumar Gala
Signed-off-by: Linus Torvalds -
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.Signed-off-by: Eric Anholt
Requested-by: Linus Torvalds
Acked-by: Dave Airlie
Signed-off-by: Linus Torvalds -
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.Signed-off-by: Gerhard Pircher
Signed-off-by: Benjamin Herrenschmidt -
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.Signed-off-by: Robert Jennings
Signed-off-by: Benjamin Herrenschmidt -
These are all powerpc specific drivers.
res.start in fsl_elbc_nand.c needs to be cast since it may be either 32
or 64 bit. Thanks to Scott Wood for noticing.Signed-off-by: Stephen Rothwell
Acked-by: Arnd Bergmann call_edac bits in particular
Acked-by: Olof Johansson pasemi_nand peices
Acked-by: Scott Wood fsl_elbc fixes
Signed-off-by: Benjamin Herrenschmidt -
Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer
Acked-by: Kumar Gala
Signed-off-by: Benjamin Herrenschmidt -
Signed-off-by: Stephen Rothwell
Signed-off-by: Benjamin Herrenschmidt -
Manual merge of:
arch/powerpc/configs/44x/warp_defconfig -
Given just how hard it is to find the code that uses MAY_APPEND
it's probably not a big surprise that this went unnoticed for so
long. The Smack rules loading code is incorrectly setting the
MAY_READ bit when MAY_APPEND is requested.Signed-off-by: Casey Schaufler
Reviewed-by: James Morris
Signed-off-by: Linus Torvalds -
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
... -
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.Signed-off-by: Anton Vorontsov
Signed-off-by: Greg Kroah-Hartman -
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.Signed-off-by: Alex Cheng
Signed-off-by: Greg Kroah-Hartman -
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.Based on a patch written by Martijn Hijdra
Signed-off-by: Phil Dibowitz
Cc: Martijn Hijdra
Signed-off-by: Greg Kroah-Hartman -
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor .
Signed-off-by: Phil Dibowitz
Signed-off-by: Greg Kroah-Hartman -
! has a higher precedence than &
Signed-off-by: Roel Kluin
Acked-by: David Brownell
Signed-off-by: Greg Kroah-Hartman -
This adds a new device id
Signed-off-by: Oliver Neukum
Signed-off-by: Greg Kroah-Hartman -
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox
Acked-by: Oliver Neukum
Signed-off-by: Greg Kroah-Hartman -
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.Signed-off-by: Marcel Sebek
Acked-by: Domenico Riccio
Signed-off-by: Greg Kroah-Hartman -
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.Signed-off-by: Phil Dibowitz
Signed-off-by: Greg Kroah-Hartman -
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.Signed-off-by: Jean-Baptiste Onofre
Signed-off-by: Phil Dibowitz
Signed-off-by: Greg Kroah-Hartman -
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.Signed-off-by: Pete Zaitcev
Cc: stable
Signed-off-by: Greg Kroah-Hartman -
Reported by Randy Dunlap from a warning on the v2.6.29 merge window.
Signed-off-by: Inaky Perez-Gonzalez
Cc: David Vrabel
Cc: Randy Dunlap
Signed-off-by: Greg Kroah-Hartman -
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson
Signed-off-by: Greg Kroah-Hartman -
This patch adds the vendor and product ID for the Alti-2 Neptune 3
(http://www.alti-2.com) which uses the FTDI chip.Signed-off-by: Robie Basak
Signed-off-by: Greg Kroah-Hartman -
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K
Signed-off-by: Greg Kroah-Hartman -
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips
Signed-off-by: Greg Kroah-Hartman -
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.Signed-off-by: stephen ware
Signed-off-by: Greg Kroah-Hartman -
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.Signed-off-by: Andrew Lunn,
Acked-by: Oliver Neukum
Signed-off-by: Greg Kroah-Hartman -
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.From: James A. Treacy
Signed-off-by: Greg Kroah-Hartman -
… whole 2 bytes of w_index
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> -
Signed-off-by: Bryan Wu
Acked-by: David Brownell
Signed-off-by: Greg Kroah-Hartman -
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies. This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.Signed-off-by: David Brownell
Signed-off-by: Greg Kroah-Hartman -
Initializes the actual_len field to 0 before every DMA transaction.
Signed-off-by: Swaminathan S
Acked-by: Felipe Balbi
Signed-off-by: David Brownell
Signed-off-by: Greg Kroah-Hartman
