15 Feb, 2007
5 commits
-
This patch enables the L220 on the RealView/EB MPCore platform.
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
The kernel originally supported revB only. This patch enables revC by
default and adds a config option for building the kernel for the revB
platform. Since the SCU base address was hard-coded in the proc-v6.S
file (and only valid for RealView/EB revB), this patch also adds a
more generic support for defining the SCU information.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
MPCore platform
This patch adds the registration of the secondary GIC on the
baseboard, together with the IRQ chaining setup.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
The current implementation only assumes one GIC to be present in the
system. However, there are platforms with more than one cascaded interrupt
controllers (RealView/EB MPCore for example).Signed-off-by: Catalin Marinas
Signed-off-by: Russell King
12 Feb, 2007
1 commit
-
This patch adds the support for the L210/L220 (outer) cache
controller. The cache range operations are done by index/way since L2
cache controller only accepts physical addresses.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King
09 Feb, 2007
1 commit
-
Other platforms other than SMP may have an outer cache. For these, we
also need to mark the page table walks outer cacheable. Since marking
the walks always outer cacheable apparantly has no side effects, we
might as well always mark them so.However, we continue to only mark PTWs shared if we have SMP enabled.
Signed-off-by: Russell King
08 Feb, 2007
9 commits
-
In consistent_sync(), start + size can end up pointing one byte
beyond the end of the direct RAM mapping. We shouldn't BUG() when
this happens.Signed-off-by: Lennert Buytenhek
Signed-off-by: Russell King -
The DMA cache handling functions take virtual addresses, but in the
form of unsigned long arguments. This leads to a little confusion
about what exactly they take. So, convert them to take const void *
instead.Signed-off-by: Russell King
-
The outer cache can be L2 as on RealView/EB MPCore platform or even L3
or further on ARMv7 cores. This patch adds the generic support for
flushing the outer cache in the DMA operations.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
Memory allocated by the coherent memory allocators will be marked
uncacheable, which means it's pointless calling consistent_sync()
to perform cache maintainence on this memory; it's just a waste of
CPU cycles.Moreover, with the (subsequent) merge of outer cache support, it
actually breaks things to call consistent_sync() on anything but
direct-mapped memory.Signed-off-by: Russell King
-
According to ARM ARM, changes to the CP15 registers are only
guaranteed to be visible after an Instruction Synchronization Barrier
(ISB). This patch adds the ISB at the end of set_cr and
set_copro_access functions and also moves them further down in the
file, below the isb macro definition.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
The architecture specification states that TLB operations are
guaranteed to be complete only after the execution of a DSB (Data
Synchronisation Barrier, former Data Write Barrier or Drain Write
Buffer). The branch target cache invalidation is also needed. The ISB
(Instruction Synchronisation Barrier, formerly Prefetch Flush) is
needed unless there will be a return from exception before the
corresponding mapping is used (i.e. user mappings).Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
On newer architectures (ARMv6, ARMv7), the depth of the prefetch and
branch prediction is implementation defined and there is a small risk
of wrong ASID tagging when changing TTBR0 before setting the new
context id. The recommended solution is to set a reserved ASID during
TTBR changing. This patch reserves ASID 0.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
The ARM Architecture Reference Manual specifies that a prefetch flush
is needed after changing the DACR register (chapter B2.7.6).Signed-off-by: Catalin Marinas
Signed-off-by: Russell King -
There are three barriers - ISB, DMB and DSB for different
scenarious. This patch adds their definitions in the system.h file.Signed-off-by: Catalin Marinas
Signed-off-by: Russell King
07 Feb, 2007
9 commits
-
bad_mode() currently prints the mode which caused the exception, and
then causes an oops dump to be printed which again displays this
information (since the CPSR in the struct pt_regs is correct.) This
leads to processor_modes[] being shared between traps.c and process.c
with a local declaration of it.We can clean this up by moving processor_modes[] to process.c and
removing the duplication, resulting in processor_modes[] becoming
static.Signed-off-by: Russell King
-
Contec Micro9 (H/M/L) boards based on Cirrus Logic ep93xx (ep9315/ep9307/ep9302).
Signed-off-by: Manfred Gruber
Signed-off-by: Lennert Buytenhek
Signed-off-by: Russell King -
This patch adds the platform resources required to support the
ixp4xx-pata-cf libata driver on Avila Gateworks boards.Signed-off-by: Alessandro Zummo
Signed-off-by: Michael-Luke Jones
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King -
This patch adds support for the Gateworks Avila Network Platform in
a separate set of setup files to the IXDP425. This is necessary now
that a driver for the Avila CF card slot is available. It also adds
support for a minor variant on the Avila board known as the Loft,
which has a different number of maximum PCI devices.Signed-off-by: Michael-Luke Jones
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King -
This patch removes references to the Gateworks Avila Network
Platform in the ixdp425 setup code. Avila setup should occur
separately now that a CF ATA device driver is available.Signed-off-by: Michael-Luke Jones
Signed-off-by: Deepak Saxena
Signed-off-by: Russell King -
csum_fold doesn't need two assembly instructions to perform its task,
it can simply add the high and low parts together by rotating by 16
bits, and the carry into the upper-16 bits will automatically happen.Also, since csum_tcpudp_magic() is just csum_tcpudp_nofold + csum_fold,
use those two functions to achieve this. Also note that there is a
csum_fold() at the end of ip_fast_csum() as well, so use the real
csum_fold() there as well.Boot tested on Versatile.
Signed-off-by: Russell King
-
Add the glue for ARM11 SMP oprofile support, which also supports the
performance monitor in the coherency unit.Signed-off-by: Russell King
-
Add oprofile glue for ARM11 (ARMv6) oprofile support. This
connects the ARM11 core profiling support to the oprofile code
for uniprocessor configurations.Signed-off-by: Russell King
-
Add basic support for the ARM11 profiling hardware. This is shared
between the ARM11 UP and ARM11 SMP oprofile support code.Signed-off-by: Russell King
05 Feb, 2007
2 commits
-
When calling into the EFI firmware, the parameters need to be passed on
the stack. The recent change to use -mregparm=3 breaks x86 EFI support.
This patch is needed to allow the new Intel-based Macs to suspend to ram
(efi.get_time is called during the suspend phase).Signed-off-by: Frederic Riss
Signed-off-by: Linus Torvalds
04 Feb, 2007
9 commits
-
That code doesn't do what its author apparently thought it would do...
Signed-off-by: Al Viro
Signed-off-by: Linus Torvalds -
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] sd: udev accessing an uninitialized scsi_disk field results in a crash
[SCSI] st: A MTIOCTOP/MTWEOF within the early warning will cause the file number to be incorrect
[SCSI] qla4xxx: bug fixes
[SCSI] Fix scsi_add_device() for async scanning -
x86-64 is missing these:
Signed-off-by: Jeff Garzik
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds -
The SN Altix platform does not conform to the IOSAPIC IRQ routing model.
Add code in acpi_unregister_gsi() to check if (acpi_irq_model ==
ACPI_IRQ_MODEL_PLATFORM) and return.Due to an oversight, this code was not added previously when
similar code was added to acpi_register_gsi().http://marc.theaimsgroup.com/?l=linux-acpi&m=116680983430121&w=2
Signed-off-by: John Keller
Acked-by: Len Brown
Cc: "Luck, Tony"
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds -
Andrew Vasquez is reporting as-iosched oopses and a 65% throughput
slowdown due to the recent special-casing of direct-io against
blockdevs. We don't know why either of these things are occurring.The patch minimally reverts us back to the 2.6.19 code for a 2.6.20
release.Cc: Andrew Vasquez
Cc: Ken Chen
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds -
We went and named them __NR_sys_foo instead of __NR_foo.
It may be too late to change this, but we can at least add the proper names
now.Signed-off-by: Mike Frysinger
Cc: Richard Henderson
Cc: Ivan Kokshaysky
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds -
smc911x_phy_configure's error handling unconditionally unlocks the
spinlock even if it wasn't locked. Patch fixes it.Signed-off-by: Peter Korsgaard
Cc: Jeff Garzik
Cc:
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds -
This patch fixes up ia64 kexec support for HP rx2620 hardware. It does
this by skipping migration of already disabled irqs. This is most likely a
problem on other ia64 platforms as well, but I've only been able to
reproduce it on one machine so far.The full story is that handle_bad_irq() gets invoked before starting the
new kernel without this patch. This seems to happen when fixup_irqs()
calls generic_handle_irq() on already migrated (and disabled) irqs. So by
avoiding migration of disabled irqs we stay away of handle_bad_irq().The code has been tested on three different ia64 machines, all with good
results. It is possible to trigger the same bug by offlining a processor
using echo 0 > /sys/devices/system/cpu/cpuX/online.More detailed information is available in the following mail thread:
http://lists.osdl.org/pipermail/fastboot/2007-January/thread.html#5774Signed-off-by: Magnus Damm
Acked-by: Simon Horman
Acked-by: Zou, Nanhai
Acked-by: Jay Lan
Acked-by: "Luck, Tony"
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds -
An AIO bug was reported that sleeping function is being called in softirq
context:BUG: warning at kernel/mutex.c:132/__mutex_lock_common()
Call Trace:
[] __mutex_lock_slowpath+0x640/0x6c0
[] mutex_lock+0x20/0x40
[] flush_workqueue+0xb0/0x1a0
[] __put_ioctx+0xc0/0x240
[] aio_complete+0x2f0/0x420
[] finished_one_bio+0x200/0x2a0
[] dio_bio_complete+0x1c0/0x200
[] dio_bio_end_aio+0x60/0x80
[] bio_endio+0x110/0x1c0
[] __end_that_request_first+0x180/0xba0
[] end_that_request_chunk+0x30/0x60
[] scsi_end_request+0x50/0x300 [scsi_mod]
[] scsi_io_completion+0x200/0x8a0 [scsi_mod]
[] sd_rw_intr+0x330/0x860 [sd_mod]
[] scsi_finish_command+0x100/0x1c0 [scsi_mod]
[] scsi_softirq_done+0x230/0x300 [scsi_mod]
[] blk_done_softirq+0x160/0x1c0
[] __do_softirq+0x200/0x240
[] do_softirq+0x70/0xc0See report: http://marc.theaimsgroup.com/?l=linux-kernel&m=116599593200888&w=2
flush_workqueue() is not allowed to be called in the softirq context.
However, aio_complete() called from I/O interrupt can potentially call
put_ioctx with last ref count on ioctx and triggers bug. It is simply
incorrect to perform ioctx freeing from aio_complete.The bug is trigger-able from a race between io_destroy() and aio_complete().
A possible scenario:cpu0 cpu1
io_destroy aio_complete
wait_for_all_aios { __aio_put_req
... ctx->reqs_active--;
if (!ctx->reqs_active)
return;
}
...
put_ioctx(ioctx)put_ioctx(ctx);
__put_ioctx
bam! Bug trigger!The real problem is that the condition check of ctx->reqs_active in
wait_for_all_aios() is incorrect that access to reqs_active is not
being properly protected by spin lock.This patch adds that protective spin lock, and at the same time removes
all duplicate ref counting for each kiocb as reqs_active is already used
as a ref count for each active ioctx. This also ensures that buggy call
to flush_workqueue() in softirq context is eliminated.Signed-off-by: "Ken Chen"
Cc: Zach Brown
Cc: Suparna Bhattacharya
Cc: Benjamin LaHaise
Cc: Badari Pulavarty
Cc:
Acked-by: Jeff Moyer
Signed-off-by: Andrew Morton
Signed-off-by: Linus Torvalds
03 Feb, 2007
4 commits
-
Fix this by letting NF_CONNTRACK_H323 depend on (IPV6 || IPV6=n).
Signed-off-by: Adrian Bunk
Signed-off-by: David S. Miller -
CC net/netfilter/nf_conntrack_netlink.o
net/netfilter/nf_conntrack_netlink.c: In function 'ctnetlink_conntrack_event':
net/netfilter/nf_conntrack_netlink.c:392: error: 'struct nf_conn' has no member named 'mark'
make[3]: *** [net/netfilter/nf_conntrack_netlink.o] Error 1Signed-off-by: Patrick McHardy
Signed-off-by: David S. Miller -
sd_probe() calls class_device_add() even before initializing the
sdkp->device variable. class_device_add() eventually results in the user mode
udev program to be called. udev program can read the the allow_restart
attribute of the newly created scsi device. This is resulting in a crash as
the show function for allow_restart (i.e sd_show_allow_restart) returns the
attribute value by reading the sdkp->device->allow_restart variable. As the
sdkp->device is not initialized before calling the user mode hotplug helper,
this results in a crash.
The patch below solves it by calling class_device_add() only after the
necessary fields in the scsi_disk structure are initialized properly.Signed-off-by: Nagendra Singh Tomar
Signed-off-by: James Bottomley -
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Initialize nbytes for internal sg commands
libata: Fix ata_busy_wait() kernel docs
pata_via: Correct missing comments
pata_atiixp: propogate cable detection hack from drivers/ide to the new driver
ahci/pata_jmicron: fix JMicron quirk
