15 Oct, 2010
3 commits
-
Instead of hand-rolling our own, just use the generic ones instead.
Signed-off-by: Paul Mundt
-
This ties in the 2KiB of FPGA SRAM in to the generic SRAM pool.
Signed-off-by: Paul Mundt
-
This sets up a generic SRAM pool for CPUs and platform code to insert
their otherwise unused memories into. A simple alloc/free interface is
provided (lifed from avr32) for generic code.This only applies to tiny SRAMs that are otherwise unmanaged, and does
not take in to account the more complex SRAMs sitting behind transfer
engines, or that employ an I/D split.Signed-off-by: Paul Mundt
14 Oct, 2010
4 commits
-
The SDK7786 FPGA has secondary control over the PCIe clocks, specifically
relating to the slots and oscillator. This ties the FPGA clocks in to the
clock framework and balances the refcounting similar to how the primary
on-chip clocks are managed. While the on-chip clocks are per-port, the
FPGA clock enable/disable is global for the entire block.Signed-off-by: Paul Mundt
-
SDK7786 supports connecting either slot3 or 4 to the same PCIe port by
way of FPGA muxing. By default the vertical slot 3 on the baseboard is
enabled, so this adds in a command line option for forcibly enabling the
slot 4 edge connector.If nothing has been specified on the command line, we fall back to
reading the resistor values for card presence to figure out where to
route the port to.Signed-off-by: Paul Mundt
-
This first converts the PMB locking over to raw spinlocks, and secondly
fixes up a nested locking issue that was triggering lockdep early on:swapper/0 is trying to acquire lock:
(&pmbe->lock){......}, at: [] pmb_init+0xf4/0x4dcbut task is already holding lock:
(&pmbe->lock){......}, at: [] pmb_init+0xc6/0x4dcother info that might help us debug this:
1 lock held by swapper/0:
#0: (&pmbe->lock){......}, at: [] pmb_init+0xc6/0x4dcSigned-off-by: Paul Mundt
-
The sdk7786 FPGA supports a number of user settable input switches that
are otherwise unused. This wires up a dummy gpio chip for the switch bank
to simply expose them to userspace.Signed-off-by: Paul Mundt
13 Oct, 2010
6 commits
-
Signed-off-by: Paul Mundt
-
Remove "name" and "id" from drivers/sh/ struct clk.
The struct clk members "name" and "id" are not used
now when matching is done through clkdev.Signed-off-by: Magnus Damm
Signed-off-by: Paul Mundt -
Without this fix the LCDC driver will try to free
framebuffer memory even though the allocation failed.Signed-off-by: Magnus Damm
Signed-off-by: Paul Mundt -
Presently this is uninitialized in the architecture code, so it's
artificlally capped to the default initialization value. Set it up at
registration time.Signed-off-by: Paul Mundt
-
The PMCAT location has conveniently moved on newer SH-X3 parts, special
case this for now with a note. This will probably want to be redone in a
less visually offensive way when/if more information becomes available.Signed-off-by: Paul Mundt
-
This plugs in the alignment and emulation fault reporting for perf sw
events.Signed-off-by: Paul Mundt
11 Oct, 2010
1 commit
-
Checks for (irq < 0) and (ilsel < 0) didn't make sense since they were
unsigned. Made them signed.Signed-off-by: Vasiliy Kulikov
Signed-off-by: Paul Mundt
07 Oct, 2010
1 commit
-
SH-3 lacks an MMUCR_TI definition for global TLB flushes. As SH-3 parts
lack a split TLB, the same global flush behaviour is accomplished
through the flush bit, which just happens to be the same as on SH-4.This fixes up the build for all SH-3 MMU parts.
Signed-off-by: Paul Mundt
06 Oct, 2010
4 commits
-
Signed-off-by: Nobuhiro Iwamatsu
Signed-off-by: Paul Mundt -
The spinlock in traps_64.c is used without initialization.
This fixes it by declaring DEFINE_SPINLOCK() and makes the spinlock static
variable.Signed-off-by: Akinobu Mita
Cc: Paul Mundt
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt -
The balancing stubs obviously need to be static inline..
Signed-off-by: Paul Mundt
-
The Kconfig and Makefile were overlooked, add those in now to improve
odds of building.Signed-off-by: Paul Mundt
05 Oct, 2010
5 commits
-
SH7786 is the big user for subgroup splitting, mostly for the PCIe block,
but those will follow later. For now we simply split up SCIF1, as used by
the serial console on SDK7786 and others.Signed-off-by: Paul Mundt
-
This splits up the sh intc core in to something more vaguely resembling
a subsystem. Most of the functionality was alread fairly well
compartmentalized, and there were only a handful of interdependencies
that needed to be resolved in the process.This also serves as future-proofing for the genirq and sparseirq rework,
which will make some of the split out functionality wholly generic,
allowing things to be killed off in place with minimal migration pain.Signed-off-by: Paul Mundt
-
If lookups happen while the radix node still points to a subgroup
mapping, an IRQ hasn't yet been made available for the specified id, so
error out accordingly. Once the slot is replaced with an IRQ mapping and
the tag is discarded, lookup can commence as normal.Signed-off-by: Paul Mundt
-
Many interrupts that share a single mask source but are on different
hardware vectors will have an associated register tied to an INTEVT that
denotes the precise cause for the interrupt exception being triggered.This introduces the concept of IRQ subgroups in the intc core, where
a virtual IRQ map is constructed for each of the pre-defined cause bits,
and a higher level chained handler takes control of the parent INTEVT.
This enables CPUs with heavily muxed IRQ vectors (especially across
disjoint blocks) to break things out in to a series of managed chained
handlers while being able to dynamically lookup and adopt the IRQs
created for them.This is largely an opt-in interface, requiring CPUs to manually submit
IRQs for subgroup splitting, in addition to providing identifiers in
their enum maps that can be used for lazy lookup via the radix tree.Signed-off-by: Paul Mundt
-
This implements a scheme roughly analogous to the PowerPC virtual to
hardware IRQ mapping, which we use for IRQ to per-controller ID mapping.
This makes it possible for drivers to use the IDs directly for lookup
instead of hardcoding the vector.The main motivation for this work is as a building block for dynamically
allocating virtual IRQs for demuxing INTC events sharing a single INTEVT
in addition to a common masking source.Signed-off-by: Paul Mundt
04 Oct, 2010
7 commits
-
The gpiolib debugfs entry takes a hammer approach and iterates over all
of the potential GPIOs, regardless of their type. The SH PFC code on the
other hand contains a variable mismash of input/output/function types
spread out sparsely, leading to situations where the debug code can
trigger an out of range enum for the type. Since we already have an error
path for out of range enums, we can just hand that up to the higher level
instead of the current BUG() behaviour.Signed-off-by: Paul Mundt
-
The gpio sysfs support needs to get at these later, so drop the
__initdata annotations.Signed-off-by: Paul Mundt
-
Presently the pinmux code is a one-way thing, but there's nothing
preventing an unregistration if no one has grabbed any of the pins.
This will permit us to save a bit of memory on systems that require pin
demux for certain peripherals in the case where registration of those
peripherals fails, or they are otherwise not attached to the system.Signed-off-by: Paul Mundt
-
At the moment ILSEL blows up with a BUG when aliased sets are handed in,
but as the enable call is able to hand back errors we opt for that path
instead. None of the ILSEL peripherals are vital to the board's
operation, so trapping a BUG is a bit excessive.Signed-off-by: Paul Mundt
-
This adds gpio-keys mappings for the button matrix on the baseboard,
now that we have support for the pin controller.Signed-off-by: Paul Mundt
-
This adds trivial support for the GPIOs implemented through the baseboard
CPLD, used for driving the button matrix.Signed-off-by: Paul Mundt
-
We'll be adding more headers for this board, so move this over to its own
directory.Signed-off-by: Paul Mundt
03 Oct, 2010
1 commit
-
As non-PFC chips are added that may support IRQs, pass through to the
generic helper instead of triggering the WARN_ON().Signed-off-by: Paul Mundt
02 Oct, 2010
4 commits
-
Some controllers will need to be initialized lazily due to pinmux
constraints, while others may simply have no need to be brought online if
there are no backing devices for them attached. In this case it's still
necessary to be able to reserve their hardware vector map before dynamic
IRQs get a hold of them.Signed-off-by: Paul Mundt
-
The SH-X3 proto CPU has all of the external IRQ and IRL pins muxed, make
sure that we're able to grab them before attempting to register their
respective IRQ controllers.Signed-off-by: Paul Mundt
-
This adds in support for GPIO/pinmux on the SH-X3 proto CPUs. This will
subsequently be used by the x3proto board.Signed-off-by: Paul Mundt
-
This adds in hardware IRQ auto-distribution support for SH-X3 proto CPUs,
following the SH7786 support.Signed-off-by: Paul Mundt
01 Oct, 2010
2 commits
-
This shuffles some of the shared bits out of the 7786 code and in to a
shared SH-X3 support file. Presently just for userimask, but also a good
place for the IRQ balancing wrappers.Signed-off-by: Paul Mundt
-
Rewrite the SH-X3 proto CPU clock framework for clkdev.
Signed-off-by: Paul Mundt
30 Sep, 2010
2 commits
-
Update the SH kernel to keep SR.BL set until the VBR
register has been initialized. Useful to allow boot
of the kernel even though exceptions are pending.Without this patch there is a window of time when
exceptions such as NMI are enabled but no exception
handlers are installed.This patch modifies both the zImage loader and the
actual kernel to boot with BL=1, but the zImage
loader is modfied in such a way that the init_sr
value is unchanged to not break the zImage loader
provided by kexec.Tested on sh7724 Ecovec and on the SH4AL-DSP core
included in sh7372.Signed-off-by: Magnus Damm
Signed-off-by: Paul Mundt -
kfree() in clkdev_drop() function should actually be called with an address of
a struct clk_lookup_alloc object, and not struct clk_lookup, as presently done.
This just happens to work, because "struct clk_lookup cl" is the first
member in struct clk_lookup_alloc.Signed-off-by: Guennadi Liakhovetski
Signed-off-by: Paul Mundt
