25 Mar, 2009
1 commit
-
No functional changes in this patch.
Signed-off-by: Erik Inge Bolsø
Signed-off-by: Jeff Garzik
26 Feb, 2009
1 commit
-
With 32bit PIO we can use the posted write buffers, but only for 32bit I/O
cycles. This means we must disable the FIFO for ATAPI where a final 16bit
cycle may occur.Rework the FIFO logic so that we disable the FIFO then selectively
re-enable it when we set the timings on AMD devices. Also fix a case
where we scribbled on PCI config 0x41 of Nvidia chips when we shouldn't.Signed-off-by: Alan Cox
Signed-off-by: Andrew Morton
Signed-off-by: Jeff Garzik
09 Jan, 2009
1 commit
-
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllersSigned-off-by: Alan Cox
Signed-off-by: Jeff Garzik
28 Oct, 2008
1 commit
-
Signed-off-by: Jeff Garzik
20 May, 2008
1 commit
-
Use the kernel-provided clamp_val() macro.
FIT was always applied to a member of struct ata_timing (unsigned short)
and two constants. clamp_val will not cast to short anymore.Signed-off-by: Harvey Harrison
Cc: Jeff Garzik
Cc: Tejun Heo
Signed-off-by: Andrew Morton
Signed-off-by: Jeff Garzik
18 Apr, 2008
7 commits
-
SFF functions have confusing names. Some have sff prefix, some have
bmdma, some std, some pci and some none. Unify the naming by...* SFF functions which are common to both BMDMA and non-BMDMA are
prefixed with ata_sff_.* SFF functions which are specific to BMDMA are prefixed with
ata_bmdma_.* SFF functions which are specific to PCI but apply to both BMDMA and
non-BMDMA are prefixed with ata_pci_sff_.* SFF functions which are specific to PCI and BMDMA are prefixed with
ata_pci_bmdma_.* Drop generic prefixes from LLD specific routines. For example,
bfin_std_dev_select -> bfin_dev_select.The following renames are noteworthy.
ata_qc_issue_prot() -> ata_sff_qc_issue()
ata_pci_default_filter() -> ata_bmdma_mode_filter()
ata_dev_try_classify() -> ata_sff_dev_classify()This rename is in preparation of separating SFF support out of libata
core layer. This patch strictly renames functions and doesn't
introduce any behavior difference.Signed-off-by: Tejun Heo
-
Current code is essentially choosing between dividing by 1 or
dividing by two, make the conditions a little more obvious.As a bonus, removes a sparse error:
drivers/ata/pata_amd.c:59:11: warning: symbol '__x' shadows an earlier one
drivers/ata/pata_amd.c:59:11: originally declared hereSigned-off-by: Harvey Harrison
Cc: Alan Cox
Signed-off-by: Andrew Morton
Signed-off-by: Jeff Garzik -
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data. In addition, port_info and host don't correspond
to each other 1-to-1. Currently, the first non-NULL
port_info->private_data is used.This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead. LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data. LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.Signed-off-by: Tejun Heo
Cc: Alan Cox -
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht. Other initialization functions take the same information
as arguments. This causes confusion and duplicate unused entries in
structures.Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly. All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.Signed-off-by: Tejun Heo
-
libata lets low level drivers build ata_port_operations table and
register it with libata core layer. This allows low level drivers
high level of flexibility but also burdens them with lots of
boilerplate entries.This becomes worse for drivers which support related similar
controllers which differ slightly. They share most of the operations
except for a few. However, the driver still needs to list all
operations for each variant. This results in large number of
duplicate entries, which is not only inefficient but also error-prone
as it becomes very difficult to tell what the actual differences are.This duplicate boilerplates all over the low level drivers also make
updating the core layer exteremely difficult and error-prone. When
compounded with multi-branched development model, it ends up
accumulating inconsistencies over time. Some of those inconsistencies
cause immediate problems and fixed. Others just remain there dormant
making maintenance increasingly difficult.To rectify the problem, this patch implements ata_port_operations
inheritance. To allow LLDs to easily re-use their own ops tables
overriding only specific methods, this patch implements poor man's
class inheritance. An ops table has ->inherits field which can be set
to any ops table as long as it doesn't create a loop. When the host
is started, the inheritance chain is followed and any operation which
isn't specified is taken from the nearest ancestor which has it
specified. This operation is called finalization and done only once
per an ops table and the LLD doesn't have to do anything special about
it other than making the ops table non-const such that libata can
update it.libata provides four base ops tables lower drivers can inherit from -
base, sata, pmp, sff and bmdma. To avoid overriding these ops
accidentaly, these ops are declared const and LLDs should always
inherit these instead of using them directly.After finalization, all the ops table are identical before and after
the patch except for setting .irq_handler to ata_interrupt in drivers
which didn't use to. The .irq_handler doesn't have any actual effect
and the field will soon be removed by later patch.* sata_sx4 is still using old style EH and currently doesn't take
advantage of ops inheritance.Signed-off-by: Tejun Heo
-
libata lets low level drivers build scsi_host_template and register it
to the SCSI layer. This allows low level drivers high level of
flexibility but also burdens them with lots of boilerplate entries.This patch implements SHT initializers which can be used to initialize
all the boilerplate entries in a sht. Three variants of them are
implemented - BASE, BMDMA and NCQ - for different types of drivers.
Note that entries can be overriden by putting individual initializers
after the helper macro.All sht tables are identical before and after this patch.
Signed-off-by: Tejun Heo
-
PCI device should be powered up or powered up before its PCI regsiters
are accessed. Although PCI configuration register access is allowed
in D3hot, PCI device is free to reset its status when transiting from
D3hot to D0 causing configuration data to change.Many libata SFF drivers which use ata_pci_init_one() read and update
configuration registers before calling ata_pci_init_one() which
enables the PCI device. Also, in resume paths, some drivers access
registers without resuming the PCI device.This patch adds a call to pcim_enable_device() in init path if
register is accessed before calling ata_pci_init_one() and make resume
paths first resume PCI devices, access PCI configuration regiters then
resume ATA host.While at it...
* cmd640 was strange in that it set ->resume even when CONFIG_PM is
not. This is by-product of minimal build fix. Updated.* In cs5530, Don't BUG() on reinit failure. Just whine and fail
resume.Signed-off-by: Tejun Heo
16 Feb, 2008
1 commit
-
drop return statement.
drivers/ata/pata_amd.c:149:2: warning: returning void-valued expressionCommit ce54d1616302117fa98513ae916bb3333e1c02ea pata_amd: update mode selection for NV PATAs
added the initializer for nv_mode_filter but missed deleting the previously
set mode_filterdrivers/ata/pata_amd.c:509:3: warning: Initializer entry defined twice
drivers/ata/pata_amd.c:521:3: also defined here
drivers/ata/pata_amd.c:544:3: warning: Initializer entry defined twice
drivers/ata/pata_amd.c:556:3: also defined hereSigned-off-by: Harvey Harrison
Signed-off-by: Jeff Garzik
12 Feb, 2008
1 commit
-
This has confused a few people so fix it
Signed-off-by: Alan Cox
Signed-off-by: Jeff Garzik
23 Jan, 2008
2 commits
-
Cable detection on NV PATA hosts isn't implemented and the CBLID-
cable isn't wired according to the sepc either, so both host-side and
generic drive-side cable detections are broken. Till now,
nv_cable_detect() relied on peeking BIOS and ACPI configurations to
upgrade to 80C but this often results in misdetection of 40C cable as
80C. Also, the original implementation was broken in that by the time
BIOS configuration is read it has already been cleared by programming
PIO0 during reset.This patch reimplements NV mode selection such that...
* BIOS configuration value is stored during driver attach and restored
on detach.* Cable type is fixed to ATA_CBL_PATA_IGN and mode selection is soley
done by nv_mode_filter() which peeks both BIOS and ACPI
configurations and filter accordingly.Signed-off-by: Tejun Heo
Cc: Alan Cox
Signed-off-by: Jeff Garzik -
Reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask() and
while at it relocate the function below ata_acpi_gtm_xfermask().New ata_acpi_cbl_80wire() implementation takes @gtm, in both pata_via
and pata_amd, use the initial GTM value. Both are trying to peek
initial BIOS configuration, so using initial caching value makes
sense. This fixes ACPI part of cable detection in pata_amd which
previously always returned 0 because configuring PIO0 during reset
clears DMA configuration.Signed-off-by: Tejun Heo
Cc: Alan Cox
Signed-off-by: Jeff Garzik
05 Dec, 2007
1 commit
-
* Don't program UDMA timings when programming PIO or MWDMA modes.
This has also a nice side-effect of fixing regression added by commit
681c80b5d96076f447e8101ac4325c82d8dce508 ("libata: correct handling of
SRST reset sequences") (->set_piomode method for PIO0 is called before
->cable_detect method which checks UDMA timings to get the cable type).* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz
Tested-by: "Thomas Lindroth"
Acked-by: Alan Cox
Cc: Tejun Heo
Signed-off-by: Andrew Morton
Signed-off-by: Bartlomiej Zolnierkiewicz
Signed-off-by: Jeff Garzik
13 Oct, 2007
5 commits
-
This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.Signed-off-by: Alan Cox
Signed-off-by: Jeff Garzik -
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().Signed-off-by: Jeff Garzik
-
We can make use of this on the pata_amd driver as many Nvidia devices
don't have reliable cable detect.Signed-off-by: Alan Cox
Signed-off-by: Jeff Garzik -
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()Signed-off-by: Jeff Garzik
-
Make reset methods and related functions deal with ata_link instead of
ata_port.* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functionsThis patch introduces no behavior change.
Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik
31 Aug, 2007
1 commit
-
Bump the versions for drivers that were modified, but had not already
had a version number bump.Signed-off-by: Jeff Garzik
12 Jul, 2007
1 commit
-
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok
Acked-by: Dave Jones
Signed-off-by: Greg Kroah-Hartman
10 Jul, 2007
2 commits
-
The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.Note that pata_it8213 mask differed from the comment. Added a FIXME there.
Signed-off-by: Jeff Garzik
-
This flag only has meaning in old-EH drivers, and these drivers have
already been converted to the new EH. Remove.Signed-off-by: Jeff Garzik
21 Jun, 2007
1 commit
-
Add the MCP73/MCP77 support to PATA driver.
The patch base on kernel 2.6.22-rc4Signed-off-by: Peer Chen
Signed-off-by: Jeff Garzik
12 May, 2007
2 commits
-
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller. This never became actually
necessary and the related code always has been subtly broken one way
or the other. Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases. Exotic
cases can simply dealt within LLDs as necessary.This patch removes port_mask handling in SFF init helpers. SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore. All information is carried via port_info. n_ports argument
is dropped and always two ports are allocated. LLD can tell SFF to
skip certain port by marking it dummy. Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic. The following changes
are made...* ata_pci_init_native_host() and ata_init_legacy_host() both now try
to initialized whatever they can and mark failed ports dummy. They
return 0 if any port is successfully initialized.* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
take n_ports argument. All info should be specified via port_info
array. Always two ports are allocated.* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.
* port_info handling in all LLDs are standardized - all port_info
arrays are const stack variable named ppi. Unless the second port
is different from the first, its port_info is specified as NULL
(tells libata that it's identical to the last non-NULL port_info).* pata_hpt37x/hpt3x2n: don't modify static variable directly. Make an
on-stack copy instead as ata_piix does.* pata_uli: It has 4 ports instead of 2. Don't use
ata_pci_prepare_native_host(). Allocate the host explicitly and use
init helpers. It's simple enough.Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik -
Reimplement suspend/resume support using sdev->manage_start_stop.
* Device suspend/resume is now SCSI layer's responsibility and the
code is simplified a lot.* DPM is dropped. This also simplifies code a lot. Suspend/resume
status is port-wide now.* ata_scsi_device_suspend/resume() and ata_dev_ready() removed.
* Resume now has to wait for disk to spin up before proceeding. I
couldn't find easy way out as libata is in EH waiting for the
disk to be ready and sd is waiting for EH to complete to issue
START_STOP.* sdev->manage_start_stop is set to 1 in ata_scsi_slave_config().
This fixes spindown on shutdown and suspend-to-disk.Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik
01 May, 2007
1 commit
-
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.* Spin up waiting is to be removed and not converted to honor
deadline.* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik
29 Apr, 2007
2 commits
-
This is added by added by cff63dfceb52c564fe1ba5394d50ab7d599a11b9
- pata: cable methods.Signed-off-by: Tejun Heo
Cc: Alan Cox
Signed-off-by: Jeff Garzik -
Versus upstream as requested
Last of the trivial switches to cable_detect methods.
Signed-off-by: Alan Cox
Signed-off-by: Jeff Garzik
03 Mar, 2007
1 commit
-
Add missing #ifdef CONFIG_PM conditionals around all PM related parts
in libata LLDs.Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik
26 Feb, 2007
1 commit
-
Bump versions based on changes submitted during 2.6.21 merge window.
Signed-off-by: Jeff Garzik
25 Feb, 2007
1 commit
-
80c test mask is at bits 18 and 19 of EIDE Controller Configuration
not 22 and 23. Fix it.Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik
10 Feb, 2007
3 commits
-
This patch is against each libata driver.
Two IRQ calls are added in ata_port_operations.
- irq_on() is used to enable interrupts.
- irq_ack() is used to acknowledge a device interrupt.In most drivers, ata_irq_on() and ata_irq_ack() are used for
irq_on and irq_ack respectively.In some drivers (ex: ahci, sata_sil24) which cannot use them
as is, ata_dummy_irq_on() and ata_dummy_irq_ack() are used.Signed-off-by: Kou Ishizaki
Signed-off-by: Akira Iguchi
Signed-off-by: Jeff Garzik -
Convert libata core layer and LLDs to use iomap.
* managed iomap is used. Pointer to pcim_iomap_table() is cached at
host->iomap and used through out LLDs. This basically replaces
host->mmio_base.* if possible, pcim_iomap_regions() is used
Most iomap operation conversions are taken from Jeff Garzik
's iomap branch.Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik -
Update libata LLDs to use devres. Core layer is already converted to
support managed LLDs. This patch simplifies initialization and fixes
many resource related bugs in init failure and detach path. For
example, all converted drivers now handle ata_device_add() failure
gracefully without excessive resource rollback code.As most resources are released automatically on driver detach, many
drivers don't need or can do with much simpler ->{port|host}_stop().
In general, stop callbacks are need iff port or host needs to be given
commands to shut it down. Note that freezing is enough in many cases
and ports are automatically frozen before being detached.Signed-off-by: Tejun Heo
Signed-off-by: Jeff Garzik
03 Dec, 2006
1 commit
-
sht->max_sectors is overrided unconditionally in ->slave_configure.
There's no reason to set it to any value.Signed-off-by: Tejun Heo
02 Dec, 2006
1 commit
-
Early AMD chips require FIFO and/or simplex flag clearing work on resume
from RAM. Most devices need no helpSigned-off-by: Alan Cox
Signed-off-by: Jeff Garzik