01 Apr, 2020
20 commits
-
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commandsMMC host:
- mmci:
* Add support for sdmmc variant revision 2.0
- mmci_sdmmc:
* Improve support for busyend detection
* Fixup support for signal voltage switch
* Add support for tuning with delay block
- mtk-sd:
* Fix another SDIO irq issue
- sdhci:
* Disable native card detect when GPIO based type exist
- sdhci:
* Add option to defer request completion
- sdhci_am654:
* Add support to set a tap value per speed mode
- sdhci-esdhc-imx:
* Add support for i.MX8MM based variant
* Fixup support for standard tuning on i.MX8 usdhc
* Optimize for strobe/clock dll settings
* Fixup support for system and runtime suspend/resume
- sdhci-iproc:
* Update regulator/bus-voltage management for bcm2711
- sdhci-msm:
* Prevent clock gating with PWRSAVE_DLL on broken variants
* Fix management of CQE during SDHCI reset
- sdhci-of-arasan:
* Add support for auto tuning on ZynqMP based platforms
- sdhci-omap:
* Add support for system suspend/resume
- sdhci-sprd:
* Add support for HW busy detection
* Enable support host software queue
- sdhci-tegra:
* Add support for HW busy detection
- tmio/renesas_sdhi:
* Enforce retune after runtime suspend
- renesas_sdhi:
* Use manual tap correction for HS400 on some variants
* Add support for manual correction of tap values for tunings"* tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: cavium-octeon: remove nonsense variable coercion
mmc: mediatek: fix SDIO irq issue
mmc: mmci_sdmmc: Fix clear busyd0end irq flag
dt-bindings: mmc: Fix node name in an example
mmc: core: Re-work the code for eMMC sanitize
mmc: sdhci: use FIELD_GET for preset value bit masks
mmc: sdhci-of-at91: Display clock changes for debug purpose only
mmc: sdhci: iproc: Add custom set_power() callback for bcm2711
mmc: sdhci: am654: Use sdhci_set_power_and_voltage()
mmc: sdhci: at91: Use sdhci_set_power_and_voltage()
mmc: sdhci: milbeaut: Use sdhci_set_power_and_voltage()
mmc: sdhci: arasan: Use sdhci_set_power_and_voltage()
mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()
mmc: vub300: Use scnprintf() for avoiding potential buffer overflow
dt-bindings: mmc: synopsys-dw-mshc: fix clock-freq-min-max in example
sdhci: tegra: Enable MMC_CAP_WAIT_WHILE_BUSY host capability
sdhci: tegra: Implement Tegra specific set_timeout callback
mmc: sdhci-omap: Add Support for Suspend/Resume
mmc: renesas_sdhi: simplify execute_tuning
mmc: renesas_sdhi: Use BITS_PER_LONG helper
... -
Pull Kbuild updates from Masahiro Yamada:
"Build system:- add CONFIG_UNUSED_KSYMS_WHITELIST, which will be useful to define a
fixed set of export symbols for Generic Kernel Image (GKI)- allow to run 'make dt_binding_check' without .config
- use full schema for checking DT examples in *.yaml files
- make modpost fail for missing MODULE_IMPORT_NS(), which makes more
sense because we know the produced modules are never loadable- Remove unused 'AS' variable
Kconfig:
- sanitize DEFCONFIG_LIST, and remove ARCH_DEFCONFIG from Kconfig
files- relax the 'imply' behavior so that symbols implied by 'y' can
become 'm'- make 'imply' obey 'depends on' in order to make 'imply' really weak
Misc:
- add documentation on building the kernel with Clang/LLVM
- revive __HAVE_ARCH_STRLEN for 32bit sparc to use optimized strlen()
- fix warning from deb-pkg builds when CONFIG_DEBUG_INFO=n
- various script and Makefile cleanups"
* tag 'kbuild-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
Makefile: Update kselftest help information
kbuild: deb-pkg: fix warning when CONFIG_DEBUG_INFO is unset
kbuild: add outputmakefile to no-dot-config-targets
kbuild: remove AS variable
net: wan: wanxl: refactor the firmware rebuild rule
net: wan: wanxl: use $(M68KCC) instead of $(M68KAS) for rebuilding firmware
net: wan: wanxl: use allow to pass CROSS_COMPILE_M68k for rebuilding firmware
kbuild: add comment about grouped target
kbuild: add -Wall to KBUILD_HOSTCXXFLAGS
kconfig: remove unused variable in qconf.cc
sparc: revive __HAVE_ARCH_STRLEN for 32bit sparc
kbuild: refactor Makefile.dtbinst more
kbuild: compute the dtbs_install destination more simply
Makefile: disallow data races on gcc-10 as well
kconfig: make 'imply' obey the direct dependency
kconfig: allow symbols implied by y to become m
net: drop_monitor: use IS_REACHABLE() to guard net_dm_hw_report()
modpost: return error if module is missing ns imports and MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS=n
modpost: rework and consolidate logging interface
kbuild: allow to run dt_binding_check without kernel configuration
... -
Pull security subsystem updates from James Morris:
"Two minor updates for the core security subsystem:- kernel-doc warning fixes from Randy Dunlap
- header cleanup from YueHaibing"
* 'next-general' of git://git.kernel.org:/pub/scm/linux/kernel/git/jmorris/linux-security:
security: remove duplicated include from security.h
security: : fix all kernel-doc warnings -
Pull SELinux updates from Paul Moore:
"We've got twenty SELinux patches for the v5.7 merge window, the
highlights are below:- Deprecate setting /sys/fs/selinux/checkreqprot to 1.
This flag was originally created to deal with legacy userspace and
the READ_IMPLIES_EXEC personality flag. We changed the default from
1 to 0 back in Linux v4.4 and now we are taking the next step of
deprecating it, at some point in the future we will take the final
step of rejecting 1.- Allow kernfs symlinks to inherit the SELinux label of the parent
directory. In order to preserve backwards compatibility this is
protected by the genfs_seclabel_symlinks SELinux policy capability.- Optimize how we store filename transitions in the kernel, resulting
in some significant improvements to policy load times.- Do a better job calculating our internal hash table sizes which
resulted in additional policy load improvements and likely general
SELinux performance improvements as well.- Remove the unused initial SIDs (labels) and improve how we handle
initial SIDs.- Enable per-file labeling for the bpf filesystem.
- Ensure that we properly label NFS v4.2 filesystems to avoid a
temporary unlabeled condition.- Add some missing XFS quota command types to the SELinux quota
access controls.- Fix a problem where we were not updating the seq_file position
index correctly in selinuxfs.- We consolidate some duplicated code into helper functions.
- A number of list to array conversions.
- Update Stephen Smalley's email address in MAINTAINERS"
* tag 'selinux-pr-20200330' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: clean up indentation issue with assignment statement
NFS: Ensure security label is set for root inode
MAINTAINERS: Update my email address
selinux: avtab_init() and cond_policydb_init() return void
selinux: clean up error path in policydb_init()
selinux: remove unused initial SIDs and improve handling
selinux: reduce the use of hard-coded hash sizes
selinux: Add xfs quota command types
selinux: optimize storage of filename transitions
selinux: factor out loop body from filename_trans_read()
security: selinux: allow per-file labeling for bpffs
selinux: generalize evaluate_cond_node()
selinux: convert cond_expr to array
selinux: convert cond_av_list to array
selinux: convert cond_list to array
selinux: sel_avc_get_stat_idx should increase position index
selinux: allow kernfs symlinks to inherit parent directory context
selinux: simplify evaluate_cond_node()
Documentation,selinux: deprecate setting checkreqprot to 1
selinux: move status variables out of selinux_ss -
Pull audit updates from Paul Moore:
"We've got two audit patches for the v5.7 merge window with a stellar
14 lines changed between the two patches. The patch descriptions are
far more lengthy than the patches themselves, which is a very good
thing for patches this size IMHO. The patches pass our test suites and
a quick summary is below:- Stop logging inode information when updating an audit file watch.
Since we are not changing the inode, or the fact that we are
watching the associated file, the inode information is just noise
that we can do without.- Fix a problem where mandatory audit records were missing their
accompanying audit records (e.g. SYSCALL records were missing).The missing records often meant that we didn't have the necessary
context to understand what was going on when the event occurred"* tag 'audit-pr-20200330' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: trigger accompanying records when no rules present
audit: CONFIG_CHANGE don't log internal bookkeeping as an event -
Pull cifs updates from Steve French:
"First part of cifs/smb3 changes for merge window (others are still
being tested). Various RDMA (smbdirect) fixes, addition of SMB3.1.1
POSIX support in readdir, 3 fixes for stable, and a fix for flock.Summary:
New feature:
- SMB3.1.1 POSIX support in readdirFixes:
- various RDMA (smbdirect) fixes
- fix for flock
- fallocate fix
- some improved mount warnings
- two timestamp related fixes
- reconnect fix
- three fixes for stable"* tag '5.7-rc-smb3-fixes-part1' of git://git.samba.org/sfrench/cifs-2.6: (28 commits)
cifs: update internal module version number
cifs: Allocate encryption header through kmalloc
cifs: smbd: Check and extend sender credits in interrupt context
cifs: smbd: Calculate the correct maximum packet size for segmented SMBDirect send/receive
smb3: use SMB2_SIGNATURE_SIZE define
CIFS: Fix bug which the return value by asynchronous read is error
CIFS: check new file size when extending file by fallocate
SMB3: Minor cleanup of protocol definitions
SMB3: Additional compression structures
SMB3: Add new compression flags
cifs: smb2pdu.h: Replace zero-length array with flexible-array member
cifs: clear PF_MEMALLOC before exiting demultiplex thread
cifs: cifspdu.h: Replace zero-length array with flexible-array member
CIFS: Warn less noisily on default mount
fs/cifs: fix gcc warning in sid_to_id
cifs: allow unlock flock and OFD lock across fork
cifs: do d_move in rename
cifs: add SMB2_open() arg to return POSIX data
cifs: plumb smb2 POSIX dir enumeration
cifs: add smb2 POSIX info level
... -
Pull gfs2 updates from Bob Peterson:
"We've got a lot of patches (39) for this merge window. Most of these
patches are related to corruption that occurs when journals are
replayed. For example:1. A node fails while writing to the file system.
2. Other nodes use the metadata that was once used by the failed
node.
3. When the node returns to the cluster, its journal is replayed, but
the older metadata blocks overwrite the changes from step 2.Summary:
- Fixed the recovery sequence to prevent corruption during journal
replay.- Many bug fixes found during recovery testing.
- New improved file system withdraw sequence.
- Fixed how resource group buffers are managed.
- Fixed how metadata revokes are tracked and written.
- Improve processing of IO errors hit by daemons like logd and
quotad.- Improved error checking in metadata writes.
- Fixed how qadata quota data structures are managed"
* tag 'gfs2-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2: (39 commits)
gfs2: Fix oversight in gfs2_ail1_flush
gfs2: change from write to read lock for sd_log_flush_lock in journal replay
gfs2: instrumentation wrt ail1 stuck
gfs2: don't lock sd_log_flush_lock in try_rgrp_unlink
gfs2: Remove unnecessary gfs2_qa_{get,put} pairs
gfs2: Split gfs2_rsqa_delete into gfs2_rs_delete and gfs2_qa_put
gfs2: Change inode qa_data to allow multiple users
gfs2: eliminate gfs2_rsqa_alloc in favor of gfs2_qa_alloc
gfs2: Switch to list_{first,last}_entry
gfs2: Clean up inode initialization and teardown
gfs2: Additional information when gfs2_ail1_flush withdraws
gfs2: leaf_dealloc needs to allocate one more revoke
gfs2: allow journal replay to hold sd_log_flush_lock
gfs2: don't allow releasepage to free bd still used for revokes
gfs2: flesh out delayed withdraw for gfs2_log_flush
gfs2: Do proper error checking for go_sync family of glops functions
gfs2: Don't demote a glock until its revokes are written
gfs2: drain the ail2 list after io errors
gfs2: Withdraw in gfs2_ail1_flush if write_cache_pages fails
gfs2: Do log_flush in gfs2_ail_empty_gl even if ail list is empty
... -
Pull btrfs updates from David Sterba:
"A number of core changes that make things work better in general, code
is simpler and cleaner.Core changes:
- per-inode file extent tree, for in memory tracking of contiguous
extent ranges to make sure i_size adjustments are accurate- tree root structures are protected by reference counts, replacing
SRCU that did not cover some cases- leak detector for tree root structures
- per-transaction pinned extent tracking
- buffer heads are replaced by bios for super block access
- speedup of extent back reference resolution, on an example test
scenario the runtime of send went down from a hour to minutes- factor out locking scheme used for subvolume writer and NOCOW
exclusion, abstracted as DREW lock, double reader-writer exclusion
(allow either readers or writers)- cleanup and abstract extent allocation policies, preparation for
zoned device support- make reflink/clone_range work on inline extents
- add more cancellation point for relocation, improves long response
from 'balance cancel'- add page migration callback for data pages
- switch to guid for uuids, with additional cleanups of the interface
- make ranged full fsyncs more efficient
- removal of obsolete ioctl flag BTRFS_SUBVOL_CREATE_ASYNC
- remove b-tree readahead from delayed refs paths, avoiding seek and
read unnecessary blocksFeatures:
- v2 of ioctl to delete subvolumes, allowing to delete by id and more
future extensionsFixes:
- fix qgroup rescan worker that could block umount
- fix crash during unmount due to race with delayed inode workers
- fix dellaloc flushing logic that could create unnecessary chunks
under heavy load- fix missing file extent item for hole after ranged fsync
- several fixes in relocation error handling
Other:
- more documentation of relocation, device replace, space
reservations- many random cleanups"
* tag 'for-5.7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (210 commits)
btrfs: fix missing semaphore unlock in btrfs_sync_file
btrfs: use nofs allocations for running delayed items
btrfs: sysfs: Use scnprintf() instead of snprintf()
btrfs: do not resolve backrefs for roots that are being deleted
btrfs: track reloc roots based on their commit root bytenr
btrfs: restart relocate_tree_blocks properly
btrfs: reloc: reorder reservation before root selection
btrfs: do not readahead in build_backref_tree
btrfs: do not use readahead for running delayed refs
btrfs: Remove async_transid from btrfs_mksubvol/create_subvol/create_snapshot
btrfs: Remove transid argument from btrfs_ioctl_snap_create_transid
btrfs: Remove BTRFS_SUBVOL_CREATE_ASYNC support
btrfs: kill the subvol_srcu
btrfs: make btrfs_cleanup_fs_roots use the radix tree lock
btrfs: don't take an extra root ref at allocation time
btrfs: hold a ref on the root on the dead roots list
btrfs: make inodes hold a ref on their roots
btrfs: move the root freeing stuff into btrfs_put_root
btrfs: move ino_cache_inode dropping out of btrfs_free_fs_root
btrfs: make the extent buffer leak check per fs info
... -
Pull fscrypt updates from Eric Biggers:
"Add an ioctl FS_IOC_GET_ENCRYPTION_NONCE which retrieves a file's
encryption nonce.This makes it easier to write automated tests which verify that
fscrypt is doing the encryption correctly"* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/fs/fscrypt/fscrypt:
ubifs: wire up FS_IOC_GET_ENCRYPTION_NONCE
f2fs: wire up FS_IOC_GET_ENCRYPTION_NONCE
ext4: wire up FS_IOC_GET_ENCRYPTION_NONCE
fscrypt: add FS_IOC_GET_ENCRYPTION_NONCE ioctl -
Pull x86 vmware updates from Ingo Molnar:
"The main change in this tree is the addition of 'steal time clock
support' for VMware guests"* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vmware: Use bool type for vmw_sched_clock
x86/vmware: Enable steal time accounting
x86/vmware: Add steal time clock support for VMware guests
x86/vmware: Remove vmware_sched_clock_setup()
x86/vmware: Make vmware_select_hypercall() __init -
Pull x86 mm updates from Ingo Molnar:
"A handful of changes:- two memory encryption related fixes
- don't display the kernel's virtual memory layout plaintext on
32-bit kernels either- two simplifications"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Remove the now redundant N_MEMORY check
dma-mapping: Fix dma_pgprot() for unencrypted coherent pages
x86: Don't let pgprot_modify() change the page encryption bit
x86/mm/kmmio: Use this_cpu_ptr() instead get_cpu_var() for kmmio_ctx
x86/mm/init/32: Stop printing the virtual memory layout -
Pull misc x86 updates from Ingo Molnar:
- extend the decoder maps with CET instructions
- fix !vDSO corner cases
* 'x86-misc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/tests: Add CET instructions to the new instructions test
x86/insn: Add Control-flow Enforcement (CET) instructions to the opcode map
selftests/x86/ptrace_syscall_32: Fix no-vDSO segfault
selftests/x86/vdso: Fix no-vDSO segfaults -
Pull x86 fpu updates from Ingo Molnar:
"Misc changes:- add a pkey sanity check
- three commits to improve and future-proof xstate/xfeature handling
some more"* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pkeys: Add check for pkey "overflow"
x86/fpu/xstate: Warn when checking alignment of disabled xfeatures
x86/fpu/xstate: Fix XSAVES offsets in setup_xstate_comp()
x86/fpu/xstate: Fix last_good_offset in setup_xstate_features() -
Pull x86 cleanups from Ingo Molnar:
"This topic tree contains more commits than usual:- most of it are uaccess cleanups/reorganization by Al
- there's a bunch of prototype declaration (--Wmissing-prototypes)
cleanups- misc other cleanups all around the map"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/mm/set_memory: Fix -Wmissing-prototypes warnings
x86/efi: Add a prototype for efi_arch_mem_reserve()
x86/mm: Mark setup_emu2phys_nid() static
x86/jump_label: Move 'inline' keyword placement
x86/platform/uv: Add a missing prototype for uv_bau_message_interrupt()
kill uaccess_try()
x86: unsafe_put-style macro for sigmask
x86: x32_setup_rt_frame(): consolidate uaccess areas
x86: __setup_rt_frame(): consolidate uaccess areas
x86: __setup_frame(): consolidate uaccess areas
x86: setup_sigcontext(): list user_access_{begin,end}() into callers
x86: get rid of put_user_try in __setup_rt_frame() (both 32bit and 64bit)
x86: ia32_setup_rt_frame(): consolidate uaccess areas
x86: ia32_setup_frame(): consolidate uaccess areas
x86: ia32_setup_sigcontext(): lift user_access_{begin,end}() into the callers
x86/alternatives: Mark text_poke_loc_init() static
x86/cpu: Fix a -Wmissing-prototypes warning for init_ia32_feat_ctl()
x86/mm: Drop pud_mknotpresent()
x86: Replace setup_irq() by request_irq()
x86/configs: Slightly reduce defconfigs
... -
Pull x86 build updates from Ingo Molnar:
"A handful of updates: two linker script cleanups and a stock
defconfig+allmodconfig bootability fix"* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Discard .note.gnu.property sections in vDSO
x86, vmlinux.lds: Add RUNTIME_DISCARD_EXIT to generic DISCARDS
x86/Kconfig: Make CMDLINE_OVERRIDE depend on non-empty CMDLINE -
Pull x86 boot updates from Ingo Molnar:
"Misc cleanups and small enhancements all around the map"* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/compressed: Fix debug_puthex() parameter type
x86/setup: Fix static memory detection
x86/vmlinux: Drop unneeded linker script discard of .eh_frame
x86/*/Makefile: Use -fno-asynchronous-unwind-tables to suppress .eh_frame sections
x86/boot/compressed: Remove .eh_frame section from bzImage
x86/boot/compressed/64: Remove .bss/.pgtable from bzImage
x86/boot/compressed/64: Use 32-bit (zero-extended) MOV for z_output_len
x86/boot/compressed/64: Use LEA to initialize boot stack pointer -
Pull arm64 updates from Catalin Marinas:
"The bulk is in-kernel pointer authentication, activity monitors and
lots of asm symbol annotations. I also queued the sys_mremap() patch
commenting the asymmetry in the address untagging.Summary:
- In-kernel Pointer Authentication support (previously only offered
to user space).- ARM Activity Monitors (AMU) extension support allowing better CPU
utilisation numbers for the scheduler (frequency invariance).- Memory hot-remove support for arm64.
- Lots of asm annotations (SYM_*) in preparation for the in-kernel
Branch Target Identification (BTI) support.- arm64 perf updates: ARMv8.5-PMU 64-bit counters, refactoring the
PMU init callbacks, support for new DT compatibles.- IPv6 header checksum optimisation.
- Fixes: SDEI (software delegated exception interface) double-lock on
hibernate with shared events.- Minor clean-ups and refactoring: cpu_ops accessor,
cpu_do_switch_mm() converted to C, cpufeature finalisation helper.- sys_mremap() comment explaining the asymmetric address untagging
behaviour"* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (81 commits)
mm/mremap: Add comment explaining the untagging behaviour of mremap()
arm64: head: Convert install_el2_stub to SYM_INNER_LABEL
arm64: Introduce get_cpu_ops() helper function
arm64: Rename cpu_read_ops() to init_cpu_ops()
arm64: Declare ACPI parking protocol CPU operation if needed
arm64: move kimage_vaddr to .rodata
arm64: use mov_q instead of literal ldr
arm64: Kconfig: verify binutils support for ARM64_PTR_AUTH
lkdtm: arm64: test kernel pointer authentication
arm64: compile the kernel with ptrauth return address signing
kconfig: Add support for 'as-option'
arm64: suspend: restore the kernel ptrauth keys
arm64: __show_regs: strip PAC from lr in printk
arm64: unwind: strip PAC from kernel addresses
arm64: mask PAC bits of __builtin_return_address
arm64: initialize ptrauth keys for kernel booting task
arm64: initialize and switch ptrauth kernel keys
arm64: enable ptrauth earlier
arm64: cpufeature: handle conflicts based on capability
arm64: cpufeature: Move cpu capability helpers inside C file
... -
Pull microblaze updates from Michal Simek:
- convert license headers to SPDX
- cleanup header handling and use asm-generic one
- get rid of earlyprintk residues
- define barriers and use it in the code
- get rid of setup_irq() for timer
- various small addons and fixes
* tag 'microblaze-v5.7-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Replace setup_irq() by request_irq()
microblaze: Stop printing the virtual memory layout
microblaze: Use asm generic cmpxchg.h for !SMP case
microblaze: Define percpu sestion in linker file
microblaze: Remove unused boot_cpuid variable
microblaze: Add missing irqflags.h header
microblaze: Add sync to tlb operations
microblaze: Define microblaze barrier
microblaze: Remove empty headers
microblaze: Remove early printk setup
microblaze: Remove architecture tlb.h and use generic one
microblaze: Convert headers to SPDX license
microblaze: Fix _reset() function
microblaze: Kernel parameters should be parsed earlier -
Pull ia64 updates from Tony Luck:
"Couple of cleanup patches"* tag 'please-pull-ia64_for_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
tty/serial: cleanup after ioc*_serial driver removal
ia64: replace setup_irq() by request_irq() -
Update kselftest help information.
Signed-off-by: Shuah Khan
Signed-off-by: Masahiro Yamada
31 Mar, 2020
20 commits
-
Pull MIPS updates from Thomas Bogendoerfer:
- loongson64 irq rework
- dmi support loongson
- replace setup_irq() by request_irq()
- jazz cleanups
- minor cleanups and fixes
* tag 'mips_5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (44 commits)
MIPS: ralink: mt7621: Fix soc_device introduction
MIPS: Exclude more dsemul code when CONFIG_MIPS_FP_SUPPORT=n
MIPS/tlbex: Fix LDDIR usage in setup_pw() for Loongson-3
MIPS: do not compile generic functions for CONFIG_CAVIUM_OCTEON_SOC
MAINTAINERS: Update Loongson64 entry
MIPS: Loongson64: Load built-in dtbs
MIPS: Loongson64: Add generic dts
dt-bindings: mips: Add loongson boards
MIPS: Loongson64: Drop legacy IRQ code
dt-bindings: interrupt-controller: Add Loongson-3 HTPIC
irqchip: Add driver for Loongson-3 HyperTransport PIC controller
dt-bindings: interrupt-controller: Add Loongson LIOINTC
irqchip: loongson-liointc: Workaround LPC IRQ Errata
irqchip: Add driver for Loongson I/O Local Interrupt Controller
docs: mips: remove no longer needed au1xxx_ide.rst documentation
MIPS: Alchemy: remove no longer used au1xxx_ide.h header
ide: remove no longer used au1xxx-ide driver
MIPS: Add support for Desktop Management Interface (DMI)
firmware: dmi: Add macro SMBIOS_ENTRY_POINT_SCAN_START
MIPS: ralink: mt7621: introduce 'soc_device' initialization
... -
Pull m68k updates from Geert Uytterhoeven:
- pagetable layout rewrite, to facilitate global READ_ONCE() rework
- Zorro (Amiga) and DIO (HP 9000/300) bus cleanups
- defconfig updates
- minor cleanups and fixes
* tag 'm68k-for-v5.7-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (23 commits)
m68k: defconfig: Update defconfigs for v5.6-rc4
zorro: Replace zero-length array with flexible-array member
m68k: Switch to asm-generic/hardirq.h
fbdev: c2p: Use BUILD_BUG() instead of custom solution
dio: Remove unused dio_dev_driver()
dio: Fix dio_bus_match() kerneldoc
dio: Make dio_match_device() static
zorro: Move zorro_bus_type to bus-private header file
zorro: Remove unused zorro_dev_driver()
zorro: Use zorro_match_device() helper in zorro_bus_match()
zorro: Fix zorro_bus_match() kerneldoc
zorro: Make zorro_match_device() static
m68k: Fix Kconfig indentation
m68k: mm: Change ColdFire pgtable_t
m68k: mm: Fully initialize the page-table allocator
m68k: mm: Extend table allocator for multiple sizes
m68k: mm: Use table allocator for pgtables
m68k: mm: Improve kernel_page_table()
m68k: mm: Restructure Motorola MMU page-table layout
m68k: mm: Move the pointer table allocator to motorola.c
... -
Pull x86 timer updates from Thomas Gleixner:
"A series of commits to make the MSR derived CPU and TSC frequency more
accurate.It turned out that the frequency tables which have been taken from the
SDM are inaccurate because the SDM provides truncated and rounded
values, e.g. 83.3Mhz (83.3333...) or 116.7Mhz (116.6666...).This causes time drift in the range of ~1 second per hour (20-30
seconds per day). On some of these SoCs it's not possible to
recalibrate the TSC because there is no reference (PIT, HPET)
available.With some reverse engineering it was established that the possible
frequencies are derived from the base clock with fixed multiplier /
divider pairs.For the CPU models which have a known crystal frequency the kernel now
uses multiplier / divider pairs which bring the frequencies closer to
reality and fix the observed time drift issues"* tag 'x86-timers-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc_msr: Make MSR derived TSC frequency more accurate
x86/tsc_msr: Fix MSR_FSB_FREQ mask for Cherry Trail devices
x86/tsc_msr: Use named struct initializers -
Pull x86 splitlock updates from Thomas Gleixner:
"Support for 'split lock' detection:Atomic operations (lock prefixed instructions) which span two cache
lines have to acquire the global bus lock. This is at least 1k cycles
slower than an atomic operation within a cache line and disrupts
performance on other cores. Aside of performance disruption this is a
unpriviledged form of DoS.Some newer CPUs have the capability to raise an #AC trap when such an
operation is attempted. The detection is by default enabled in warning
mode which will warn once when a user space application is caught. A
command line option allows to disable the detection or to select fatal
mode which will terminate offending applications with SIGBUS"* tag 'x86-splitlock-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/split_lock: Avoid runtime reads of the TEST_CTRL MSR
x86/split_lock: Rework the initialization flow of split lock detection
x86/split_lock: Enable split lock detection by kernel -
Pull x86 entry code updates from Thomas Gleixner:
- Convert the 32bit syscalls to be pt_regs based which removes the
requirement to push all 6 potential arguments onto the stack and
consolidates the interface with the 64bit variant- The first small portion of the exception and syscall related entry
code consolidation which aims to address the recently discovered
issues vs. RCU, int3, NMI and some other exceptions which can
interrupt any context. The bulk of the changes is still work in
progress and aimed for 5.8.- A few lockdep namespace cleanups which have been applied into this
branch to keep the prerequisites for the ongoing work confined.* tag 'x86-entry-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (35 commits)
x86/entry: Fix build error x86 with !CONFIG_POSIX_TIMERS
lockdep: Rename trace_{hard,soft}{irq_context,irqs_enabled}()
lockdep: Rename trace_softirqs_{on,off}()
lockdep: Rename trace_hardirq_{enter,exit}()
x86/entry: Rename ___preempt_schedule
x86: Remove unneeded includes
x86/entry: Drop asmlinkage from syscalls
x86/entry/32: Enable pt_regs based syscalls
x86/entry/32: Use IA32-specific wrappers for syscalls taking 64-bit arguments
x86/entry/32: Rename 32-bit specific syscalls
x86/entry/32: Clean up syscall_32.tbl
x86/entry: Remove ABI prefixes from functions in syscall tables
x86/entry/64: Add __SYSCALL_COMMON()
x86/entry: Remove syscall qualifier support
x86/entry/64: Remove ptregs qualifier from syscall table
x86/entry: Move max syscall number calculation to syscallhdr.sh
x86/entry/64: Split X32 syscall table into its own file
x86/entry/64: Move sys_ni_syscall stub to common.c
x86/entry/64: Use syscall wrappers for x32_rt_sigreturn
x86/entry: Refactor SYS_NI macros
... -
Pull timekeeping and timer updates from Thomas Gleixner:
"Core:- Consolidation of the vDSO build infrastructure to address the
difficulties of cross-builds for ARM64 compat vDSO libraries by
restricting the exposure of header content to the vDSO build.This is achieved by splitting out header content into separate
headers. which contain only the minimaly required information which
is necessary to build the vDSO. These new headers are included from
the kernel headers and the vDSO specific files.- Enhancements to the generic vDSO library allowing more fine grained
control over the compiled in code, further reducing architecture
specific storage and preparing for adopting the generic library by
PPC.- Cleanup and consolidation of the exit related code in posix CPU
timers.- Small cleanups and enhancements here and there
Drivers:
- The obligatory new drivers: Ingenic JZ47xx and X1000 TCU support
- Correct the clock rate of PIT64b global clock
- setup_irq() cleanup
- Preparation for PWM and suspend support for the TI DM timer
- Expand the fttmr010 driver to support ast2600 systems
- The usual small fixes, enhancements and cleanups all over the
place"* tag 'timers-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (80 commits)
Revert "clocksource/drivers/timer-probe: Avoid creating dead devices"
vdso: Fix clocksource.h macro detection
um: Fix header inclusion
arm64: vdso32: Enable Clang Compilation
lib/vdso: Enable common headers
arm: vdso: Enable arm to use common headers
x86/vdso: Enable x86 to use common headers
mips: vdso: Enable mips to use common headers
arm64: vdso32: Include common headers in the vdso library
arm64: vdso: Include common headers in the vdso library
arm64: Introduce asm/vdso/processor.h
arm64: vdso32: Code clean up
linux/elfnote.h: Replace elf.h with UAPI equivalent
scripts: Fix the inclusion order in modpost
common: Introduce processor.h
linux/ktime.h: Extract common header for vDSO
linux/jiffies.h: Extract common header for vDSO
linux/time64.h: Extract common header for vDSO
linux/time32.h: Extract common header for vDSO
linux/time.h: Extract common header for vDSO
... -
Pull NOHZ update from Thomas Gleixner:
"Remove TIF_NOHZ from three architecturesThese architectures use a static key to decide whether context
tracking needs to be invoked and the TIF_NOHZ flag just causes a
pointless slowpath execution for nothing"* tag 'timers-nohz-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64: Remove TIF_NOHZ
arm: Remove TIF_NOHZ
x86: Remove TIF_NOHZ
context-tracking: Introduce CONFIG_HAVE_TIF_NOHZ
x86/entry: Remove _TIF_NOHZ from _TIF_WORK_SYSCALL_ENTRY -
Pull core SMP updates from Thomas Gleixner:
"CPU (hotplug) updates:- Support for locked CSD objects in smp_call_function_single_async()
which allows to simplify callsites in the scheduler core and MIPS- Treewide consolidation of CPU hotplug functions which ensures the
consistency between the sysfs interface and kernel state. The low
level functions cpu_up/down() are now confined to the core code and
not longer accessible from random code"* tag 'smp-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
cpu/hotplug: Ignore pm_wakeup_pending() for disable_nonboot_cpus()
cpu/hotplug: Hide cpu_up/down()
cpu/hotplug: Move bringup of secondary CPUs out of smp_init()
torture: Replace cpu_up/down() with add/remove_cpu()
firmware: psci: Replace cpu_up/down() with add/remove_cpu()
xen/cpuhotplug: Replace cpu_up/down() with device_online/offline()
parisc: Replace cpu_up/down() with add/remove_cpu()
sparc: Replace cpu_up/down() with add/remove_cpu()
powerpc: Replace cpu_up/down() with add/remove_cpu()
x86/smp: Replace cpu_up/down() with add/remove_cpu()
arm64: hibernate: Use bringup_hibernate_cpu()
cpu/hotplug: Provide bringup_hibernate_cpu()
arm64: Use reboot_cpu instead of hardconding it to 0
arm64: Don't use disable_nonboot_cpus()
ARM: Use reboot_cpu instead of hardcoding it to 0
ARM: Don't use disable_nonboot_cpus()
ia64: Replace cpu_down() with smp_shutdown_nonboot_cpus()
cpu/hotplug: Create a new function to shutdown nonboot cpus
cpu/hotplug: Add new {add,remove}_cpu() functions
sched/core: Remove rq.hrtick_csd_pending
... -
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
... -
There's a semantic conflict in the Octeon staging network driver, which
used the skb_reset_tc() function to reset skb state when re-using an
skb. But that inline helper function was removed in mainline by commit
2c64605b590e ("net: Fix CONFIG_NET_CLS_ACT=n and
CONFIG_NFT_FWD_NETDEV={y, m} build").Fix it by using skb_reset_redirect() instead. Also move it out of the
This code path only ends up triggering if REUSE_SKBUFFS_WITHOUT_FREE is
enabled, which in turn only happens if you don't have CONFIG_NETFILTER
configured. Which was how this wasn't caught by the usual allmodconfig
builds.Signed-off-by: Randy Dunlap
Reported-by: Stephen Rothwell
Signed-off-by: Linus Torvalds -
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:- Various NUMA scheduling updates: harmonize the load-balancer and
NUMA placement logic to not work against each other. The intended
result is better locality, better utilization and fewer migrations.- Introduce Thermal Pressure tracking and optimizations, to improve
task placement on thermally overloaded systems.- Implement frequency invariant scheduler accounting on (some) x86
CPUs. This is done by observing and sampling the 'recent' CPU
frequency average at ~tick boundaries. The CPU provides this data
via the APERF/MPERF MSRs. This hopefully makes our capacity
estimates more precise and keeps tasks on the same CPU better even
if it might seem overloaded at a lower momentary frequency. (As
usual, turbo mode is a complication that we resolve by observing
the maximum frequency and renormalizing to it.)- Add asymmetric CPU capacity wakeup scan to improve capacity
utilization on asymmetric topologies. (big.LITTLE systems)- PSI fixes and optimizations.
- RT scheduling capacity awareness fixes & improvements.
- Optimize the CONFIG_RT_GROUP_SCHED constraints code.
- Misc fixes, cleanups and optimizations - see the changelog for
details"* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
threads: Update PID limit comment according to futex UAPI change
sched/fair: Fix condition of avg_load calculation
sched/rt: cpupri_find: Trigger a full search as fallback
kthread: Do not preempt current task if it is going to call schedule()
sched/fair: Improve spreading of utilization
sched: Avoid scale real weight down to zero
psi: Move PF_MEMSTALL out of task->flags
MAINTAINERS: Add maintenance information for psi
psi: Optimize switching tasks inside shared cgroups
psi: Fix cpu.pressure for cpu.max and competing cgroups
sched/core: Distribute tasks within affinity masks
sched/fair: Fix enqueue_task_fair warning
thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code
sched/rt: Remove unnecessary push for unfit tasks
sched/rt: Allow pulling unfitting task
sched/rt: Optimize cpupri_find() on non-heterogenous systems
sched/rt: Re-instate old behavior in select_task_rq_rt()
sched/rt: cpupri_find: Implement fallback mechanism for !fit case
sched/fair: Fix reordering of enqueue/dequeue_task_fair()
sched/fair: Fix runnable_avg for throttled cfs
... -
The assignment of e->type_names is indented one level too deep,
clean this up by removing the extraneous tab.Signed-off-by: Colin Ian King
Signed-off-by: Paul Moore -
When using NFSv4.2, the security label for the root inode should be set
via a call to nfs_setsecurity() during the mount process, otherwise the
inode will appear as unlabeled for up to acdirmin seconds. Currently
the label for the root inode is allocated, retrieved, and freed entirely
witin nfs4_proc_get_root().Add a field for the label to the nfs_fattr struct, and allocate & free
the label in nfs_get_root(), where we also add a call to
nfs_setsecurity(). Note that for the call to nfs_setsecurity() to
succeed, it's necessary to also move the logic calling
security_sb_{set,clone}_security() from nfs_get_tree_common() down into
nfs_get_root()... otherwise the SBLABEL_MNT flag will not be set in the
super_block's security flags and nfs_setsecurity() will silently fail.Reported-by: Richard Haines
Signed-off-by: Scott Mayhew
Acked-by: Stephen Smalley
Tested-by: Stephen Smalley
[PM: fixed 80-char line width problems]
Signed-off-by: Paul Moore -
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
... -
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
... -
Pull EFI updates from Ingo Molnar:
"The EFI changes in this cycle are much larger than usual, for two
(positive) reasons:- The GRUB project is showing signs of life again, resulting in the
introduction of the generic Linux/UEFI boot protocol, instead of
x86 specific hacks which are increasingly difficult to maintain.
There's hope that all future extensions will now go through that
boot protocol.- Preparatory work for RISC-V EFI support.
The main changes are:
- Boot time GDT handling changes
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file
I/O, memory allocation, etc.- Introduce a generic initrd loading method based on calling back
into the firmware, instead of relying on the x86 EFI handover
protocol or device tree.- Introduce a mixed mode boot method that does not rely on the x86
EFI handover protocol either, and could potentially be adopted by
other architectures (if another one ever surfaces where one
execution mode is a superset of another)- Clean up the contents of 'struct efi', and move out everything that
doesn't need to be stored there.- Incorporate support for UEFI spec v2.8A changes that permit
firmware implementations to return EFI_UNSUPPORTED from UEFI
runtime services at OS runtime, and expose a mask of which ones are
supported or unsupported via a configuration table.- Partial fix for the lack of by-VA cache maintenance in the
decompressor on 32-bit ARM.- Changes to load device firmware from EFI boot service memory
regions- Various documentation updates and minor code cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
efi/libstub/arm: Fix spurious message that an initrd was loaded
efi/libstub/arm64: Avoid image_base value from efi_loaded_image
partitions/efi: Fix partition name parsing in GUID partition entry
efi/x86: Fix cast of image argument
efi/libstub/x86: Use ULONG_MAX as upper bound for all allocations
efi: Fix a mistype in comments mentioning efivar_entry_iter_begin()
efi/libstub: Avoid linking libstub/lib-ksyms.o into vmlinux
efi/x86: Preserve %ebx correctly in efi_set_virtual_address_map()
efi/x86: Ignore the memory attributes table on i386
efi/x86: Don't relocate the kernel unless necessary
efi/x86: Remove extra headroom for setup block
efi/x86: Add kernel preferred address to PE header
efi/x86: Decompress at start of PE image load address
x86/boot/compressed/32: Save the output address instead of recalculating it
efi/libstub/x86: Deal with exit() boot service returning
x86/boot: Use unsigned comparison for addresses
efi/x86: Avoid using code32_start
efi/x86: Make efi32_pe_entry() more readable
efi/x86: Respect 32-bit ABI in efi32_pe_entry()
efi/x86: Annotate the LOADED_IMAGE_PROTOCOL_GUID with SYM_DATA
... -
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:- Make kfree_rcu() use kfree_bulk() for added performance
- RCU updates
- Callback-overload handling updates
- Tasks-RCU KCSAN and sparse updates
- Locking torture test and RCU torture test updates
- Documentation updates
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (74 commits)
rcu: Make rcu_barrier() account for offline no-CBs CPUs
rcu: Mark rcu_state.gp_seq to detect concurrent writes
Documentation/memory-barriers: Fix typos
doc: Add rcutorture scripting to torture.txt
doc/RCU/rcu: Use https instead of http if possible
doc/RCU/rcu: Use absolute paths for non-rst files
doc/RCU/rcu: Use ':ref:' for links to other docs
doc/RCU/listRCU: Update example function name
doc/RCU/listRCU: Fix typos in a example code snippets
doc/RCU/Design: Remove remaining HTML tags in ReST files
doc: Add some more RCU list patterns in the kernel
rcutorture: Set KCSAN Kconfig options to detect more data races
rcutorture: Manually clean up after rcu_barrier() failure
rcutorture: Make rcu_torture_barrier_cbs() post from corresponding CPU
rcuperf: Measure memory footprint during kfree_rcu() test
rcutorture: Annotation lockless accesses to rcu_torture_current
rcutorture: Add READ_ONCE() to rcu_torture_count and rcu_torture_batch
rcutorture: Fix stray access to rcu_fwd_cb_nodelay
rcutorture: Fix rcu_torture_one_read()/rcu_torture_writer() data race
rcutorture: Make kvm-find-errors.sh abort on bad directory
... -
Pull objtool updates from Ingo Molnar:
"The biggest changes in this cycle were the vmlinux.o optimizations by
Peter Zijlstra, which are preparatory and optimization work to run
objtool against the much richer vmlinux.o object file, to perform
new, whole-program section based logic. That work exposed a handful
of problems with the existing code, which fixes and optimizations are
merged here. The complete 'vmlinux.o and noinstr' work is still work
in progress, targeted for v5.8.There's also assorted fixes and enhancements from Josh Poimboeuf.
In particular I'd like to draw attention to commit 644592d328370,
which turns fatal objtool errors into failed kernel builds. This
behavior is IMO now justified on multiple grounds (it's easy currently
to not notice an essentially corrupted kernel build), and the commit
has been in -next testing for several weeks, but there could still be
build failures with old or weird toolchains. Should that be widespread
or high profile enough then I'd suggest a quick revert, to not hold up
the merge window"* 'core-objtool-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
objtool: Re-arrange validate_functions()
objtool: Optimize find_rela_by_dest_range()
objtool: Delete cleanup()
objtool: Optimize read_sections()
objtool: Optimize find_symbol_by_name()
objtool: Resize insn_hash
objtool: Rename find_containing_func()
objtool: Optimize find_symbol_*() and read_symbols()
objtool: Optimize find_section_by_name()
objtool: Optimize find_section_by_index()
objtool: Add a statistics mode
objtool: Optimize find_symbol_by_index()
x86/kexec: Make relocate_kernel_64.S objtool clean
x86/kexec: Use RIP relative addressing
objtool: Rename func_for_each_insn_all()
objtool: Rename func_for_each_insn()
objtool: Introduce validate_return()
objtool: Improve call destination function detection
objtool: Fix clang switch table edge case
objtool: Add relocation check for alternative sections
... -
Pull PNP subsystem updates from Rafael Wysocki:
- Update MAINTAINERS to cover include/linux/pnp.h and add the
linux-acpi list to the PNP entry in it- add the const modifier to the name field definition in struct
pnp_driver- drop a pointer case in the RTC CMOS driver that has become redundant
All by Corentin Labbe.
* tag 'pnp-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
MAINTAINERS: Add linux-acpi list to PNP
rtc: cmos: remove useless cast for driver_name
PNP: constify driver name
PNP: add missing include/linux/pnp.h to MAINTAINERS -
Pull ACPI updates from Rafael Wysocki:
- Update the ACPICA code in the kernel to the 20200214 upstream
release including:* Fix to re-enable the sleep button after wakeup (Anchal
Agarwal).* Fixes for mistakes in comments and typos (Bob Moore).
* ASL-ASL+ converter updates (Erik Kaneda).
* Type casting cleanups (Sven Barth).
- Clean up the intialization of the EC driver and eliminate some dead
code from it (Rafael Wysocki).- Clean up the quirk tables in the AC and battery drivers (Hans de
Goede).- Fix the global lock handling on x86 to ignore unspecified bit
positions in the global lock field (Jan Engelhardt).- Add a new "tiny" driver for ACPI button devices exposed by VMs to
guest kernels to send signals directly to init (Josh Triplett).- Add a kernel parameter to disable ACPI BGRT on x86 (Alex Hung).
- Make the ACPI PCI host bridge and fan drivers use scnprintf() to
avoid potential buffer overflows (Takashi Iwai).- Clean up assorted pieces of code:
* Reorder "asmlinkage" to make g++ happy (Alexey Dobriyan).
* Drop unneeded variable initialization (Colin Ian King).
* Add missing __acquires/__releases annotations (Jules Irenge).
* Replace list_for_each_safe() with list_for_each_entry_safe()
(chenqiwu)"* tag 'acpi-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (31 commits)
ACPICA: Update version to 20200214
ACPI: PCI: Use scnprintf() for avoiding potential buffer overflow
ACPI: fan: Use scnprintf() for avoiding potential buffer overflow
ACPI: EC: Eliminate EC_FLAGS_QUERY_HANDSHAKE
ACPI: EC: Do not clear boot_ec_is_ecdt in acpi_ec_add()
ACPI: EC: Simplify acpi_ec_ecdt_start() and acpi_ec_init()
ACPI: EC: Consolidate event handler installation code
acpi/x86: ignore unspecified bit positions in the ACPI global lock field
acpi/x86: add a kernel parameter to disable ACPI BGRT
x86/acpi: make "asmlinkage" part first thing in the function definition
ACPI: list_for_each_safe() -> list_for_each_entry_safe()
ACPI: video: remove redundant assignments to variable result
ACPI: OSL: Add missing __acquires/__releases annotations
ACPI / battery: Cleanup Lenovo Ideapad Miix 320 DMI table entry
ACPI / AC: Cleanup DMI quirk table
ACPI: EC: Use fast path in acpi_ec_add() for DSDT boot EC
ACPI: EC: Simplify acpi_ec_add()
ACPI: EC: Drop AE_NOT_FOUND special case from ec_install_handlers()
ACPI: EC: Avoid passing redundant argument to functions
ACPI: EC: Avoid printing confusing messages in acpi_ec_setup()
...
