26 Jul, 2010
40 commits
-
CPUIMX51 is build around Freescale's i.MX515 and has up to
512MB of RAM, NAND Flash, Ethernet, USB Host with 4 ports
hub, USB OTG, ST16554 Quad UART on nCS1, I2C RTC ...MBIMX51 adds LEDS, Keypad, TSC2007 touchscreen controler ...
Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
The commit 9a763bf "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.Signed-off-by: Jason Wang
Tested-by: Eric Bénard
Signed-off-by: Sascha Hauer -
as per suggested by Sascha
Signed-off-by: Eric Bénard
Acked-by: Uwe Kleine-König
Signed-off-by: Sascha Hauer -
This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice groupSigned-off-by: Eric Bénard
Acked-by: Uwe Kleine-König
Signed-off-by: Sascha Hauer -
Signed-off-by: Eric Bénard
Acked-by: Uwe Kleine-König
Signed-off-by: Sascha Hauer -
Signed-off-by: Marc Kleine-Budde
Signed-off-by: Sascha Hauer -
In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: Marc Kleine-Budde
Signed-off-by: Sascha Hauer -
Signed-off-by: Marc Kleine-Budde
Signed-off-by: Sascha Hauer -
Signed-off-by: Marc Kleine-Budde
Signed-off-by: Sascha Hauer -
Signed-off-by: Marc Kleine-Budde
Signed-off-by: Sascha Hauer -
Signed-off-by: Marc Kleine-Budde
Signed-off-by: Sascha Hauer -
Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
the i2c_board_info structure landed into the SPI #if/#endif
which is wrong.Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
Signed-off-by: Eric Bénard
Cc: s.hauer@pengutronix.de
Cc: linux-mmc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Sascha Hauer -
Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
add imx_keypad platform device definition and clocks for mx51
platforms.Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
3-stack is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
mx27_3ds: add support for the keypad
Signed-off-by: Rogerio Pimentel
Signed-off-by: Sascha Hauer -
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.Signed-off-by: Uwe Kleine-König
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h -
Signed-off-by: Baruch Siach
Signed-off-by: Sascha Hauer -
Signed-off-by: Baruch Siach
Signed-off-by: Sascha Hauer -
Signed-off-by: Fabio Estevam
Signed-off-by: Sascha Hauer -
Signed-off-by: Baruch Siach
Signed-off-by: Sascha Hauer -
Signed-off-by: Baruch Siach
Signed-off-by: Sascha Hauer -
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.Signed-off-by: Luotao Fu
Signed-off-by: Sascha Hauer -
this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.Signed-off-by: Luotao Fu
Signed-off-by: Sascha Hauer -
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.Signed-off-by: Jason Wang
Signed-off-by: Sascha Hauer -
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'Signed-off-by: Amit Kucheria
Signed-off-by: Sascha Hauer -
* cpuimx35 integrates i.MX35, RAM, NAND, Ethernet, I2C RTC, USB Host,
USB OTG and I2C touchscreen controller
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer -
The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.Signed-off-by: Baruch Siach
Acked-by: Wolfram Sang
Signed-off-by: Sascha Hauer -
Signed-off-by: Baruch Siach
Reviewed-by: Wolfram Sang
Signed-off-by: Sascha Hauer -
Signed-off-by: Baruch Siach
Reviewed-by: Wolfram Sang
Signed-off-by: Sascha Hauer -
* cpuimx25 integrates i.MX25, RAM, NAND, Ethernet, I2C RTC, USB Host
and USB OTG
* mbimxsd provides access to LCD, Audio, LED, Switch button, UART ...Signed-off-by: Eric Bénard
Signed-off-by: Sascha Hauer
