31 Dec, 2014
1 commit
-
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
16 Dec, 2014
1 commit
-
This adds the register offsets for pull up/down for the STMPE
1601, 1801 and 24xx expanders. This is used to bias GPIO lines
and keypad lines.Signed-off-by: Linus Walleij
Acked-by: Lee Jones
Signed-off-by: Dmitry Torokhov
10 Nov, 2014
1 commit
-
The least significat byte of the GPIO value read register
on the STMPE24xx series is on addres 0xA4 not 0xA5. Correct
against datasheet and tested on the STMPE2401 hardware.Signed-off-by: Linus Walleij
Signed-off-by: Lee Jones
09 Jul, 2014
1 commit
-
Extinguishes:
../drivers/mfd/stmpe-i2c.c: In function ‘stmpe_i2c_probe’:
../drivers/mfd/stmpe-i2c.c:88:13:
warning: cast from pointer to integer of different size
partnum = (int)of_id->data;Reviewed-by: Linus Walleij
Signed-off-by: Lee Jones
09 May, 2014
1 commit
-
The STMPE driver would just read/modify/write the system control
register on the STMPE1601, meaning it would not properly mask off
the PWM block, which remained active if it was on at boot time.
This makes sure the blocks are always masked off if they were
active on boot, saving some power. Also rename the inconsistenty
named STMPE1601 define for the PWM block activation.Signed-off-by: Linus Walleij
06 Jan, 2014
1 commit
-
As of commit 03e361b25ee8dfb1fd9b890072c23c4aae01c6c7 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.Signed-off-by: Geert Uytterhoeven
Signed-off-by: Lee Jones
09 Apr, 2013
1 commit
-
Provides support for 1801 variant of stmpe gpio port expanders.
This chip has 18 gpios configurable as GPI, GPO, keypad matrix,
special key or dedicated key function.Note that special/dedicated key function is not supported yet.
Signed-off-by: Jean-Nicolas Graux
Acked-by: Linus Walleij
Signed-off-by: Samuel Ortiz
09 Jan, 2012
3 commits
-
STMPE801 is a GPIO expander. Registers for 801 are much different from other
variants. This patch adds support for STMPE801 in stmpe mfd driver.Signed-off-by: Bhupesh Sharma
Signed-off-by: Pratyush Anand
Signed-off-by: Viresh Kumar
Signed-off-by: Samuel Ortiz -
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C.This patch adds support for SPI interface for accessing STMPE's address space.
Signed-off-by: Viresh Kumar
Acked-by: Linus Walleij
Signed-off-by: Samuel Ortiz -
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C and all code is present in a single file
stmpe.c. It would be better to separate out I2C interface specific code from
controller specific code. Later SPI specific code can be added in a separate
file.This patch separates out I2C and controller specific code into separate files,
making stmpe.c independent of I2C.Signed-off-by: Viresh Kumar
Acked-by: Linus Walleij
Signed-off-by: Samuel Ortiz
01 Aug, 2011
1 commit
-
Generating kerneldoc for STMPE result in warnings, so fix this by
adding missing documentation.Signed-off-by: Om Prakash
Reviewed-by: Rabin Vincent
Reviewed-by: Jonas Aberg
Reviewed-by: Srinidhi Kasagar
Signed-off-by: Linus Walleij
Signed-off-by: Samuel Ortiz
12 Aug, 2010
2 commits
-
Some STMPE devices support entering sleep mode automatically on a
specified timeout of inactivity on the I2C bus with the host system.Acked-by: Linus Walleij
Acked-by: Rabin Vincent
Signed-off-by: Sundar R Iyer
Signed-off-by: Samuel Ortiz -
Add support for the STMPE family of I/O Expanders from
STMicroelectronics. These devices include upto 24 gpios and a varying
selection of blocks, including PWM, keypad, and touchscreen controllers.
This patch adds the MFD core.[l.fu@pengutronix.de: fix stmpe811 enable hook]
[l.fu@pengutronix.de: add touchscreen platform data]
Acked-by: Luotao Fu
Acked-by: Linus Walleij
Signed-off-by: Rabin Vincent
Signed-off-by: Samuel Ortiz
