27 Apr, 2019
1 commit
26 Nov, 2018
1 commit
-
The description of dmas pointed to the common description of dma,
and the introduction of dmas was unclear. Add a doc link to sdma
introduction.Signed-off-by: Clark Wang
02 Nov, 2018
2 commits
-
In order to support 44kHz and 48kHz sample rate together, we need to
reconfigure the parent clock of mclk.Signed-off-by: Shengjiu Wang
-
Add "fsl,imx8mm-usb" compatible string.
Acked-by: Peter Chen
Signed-off-by: Li Jun
29 Oct, 2018
36 commits
-
Some platforms may want to use USB PHY charger detection function
when VBUS is there, add one flag for it. The user can enable it
at firmware.Reviewed-by: Jun Li
Signed-off-by: Peter Chen -
This is an adapter card made for the 4.3", 800x480, LCD panel Seiko
43WVFIG. The LCD panel is a 24bit DPI bus, while the adapter card has
two ports: 18-bit and 24-bit data input. For the 18-bit data input, the
adapter card is demuxing some of the data lines, in order to feed all of
the 24 lines needed by the LCD.
This driver handles both this use-cases.Signed-off-by: Robert Chiras
-
Add driver for Seiko Instruments Inc. 4.3" WVGA (800 x RGB x 480)
TFT with Touch-Panel.Datasheet available at:
http://www.glyn.de/data/glyn/media/doc/43wvf1g-0.pdfSeiko 43WVF1G panel has two power supplies: avdd and dvdd and they
require a specific power on/down sequence.
For this reason the simple panel driver cannot be used to drive this
panel, so create a new one heavily based on simple panel.Based on initial patch submission from Breno Lima.
Signed-off-by: Marco Franchi
Signed-off-by: Thierry Reding
Link: https://patchwork.freedesktop.org/patch/msgid/1500567179-6967-1-git-send-email-marco.franchi@nxp.com -
This patch is to add CAN wakeup function on MX8 platforms and update the
binding file fsl-flexcan.txt.For MX8, the function "flexcan_irq()" should not call "flexcan_exit_stop_mode()"
due to firmware(SCU) cannot make SC IPC calls from an interrupt context.
If not exit stop mode in ISR, it will continuously enter wakeup ISR for the reason
that system will respond IRQ before call CAN system resume.
To fix the issue, we can exit stop mode during noirq resume stage.For wakeup case, it should not set pinctrl to sleep state by
pinctrl_pm_select_sleep_state.Reviewed-by: Dong Aisheng
Reviewed-by: Andy Duan
Signed-off-by: Joakim Zhang -
Add xen,i2c bindings
Signed-off-by: Peng Fan
-
FLEXCAN has supported selecting the clock source to the CAN Protocol Engine (PE).
It's SoC Implementation dependent. Refer to RM for detailed definition of each SoC.Signed-off-by: Joakim Zhang
-
tree
Normally CAN FD capable device must work on FD mode as it has different
statically claimed bittiming capability.
This patch provides users to disable CAN FD capability if users want
to only work at normal mode.Signed-off-by: Joakim Zhang
-
Add "spi-slave" attribute for recognizing slave mode.
If it is not in slave mode, please delete this attribute.
Usage can be found at spi-fsl-lpspi.txt.Modify "Makefile" to build "imx7ulp-evk-spi-slave.dtb".
Signed-off-by: Xiaoning Wang
-
On imx8qm mek, the cs42888 is connected with i2c in cm41 domain,
but wm8960 is connected with i2c1, which is not in m4 domain.
So we only need to eable rpmsg for cs42888.Signed-off-by: Shengjiu Wang
(cherry picked from commit 9d2368aef40e4d107e4deee1a2c7e191c1afe644) -
According to AK5558 MCLK frequence must not exceed 36.864 MHz.
Limit maximum supported rate as function of max MCLK frequency,
sample bits and number of slots.Signed-off-by: Viorel Suman
Reviewed-by: Shengjiu Wang
(cherry picked from commit 236796cad225daa39d5b77d763a1d964dd4de4c9) -
Pixel combiner found in i.MX8 SoCs may combine two display
streams(one master and the other slave) to drive a high
pixel rate display. This patch adds DT property descriptions
in imx-drm DT documentation for pixel combiner.Signed-off-by: Liu Ying
-
Add two parameters which are used to tune USB signal for picophy,
picophy is used at imx7d and imx845.Signed-off-by: Peter Chen
-
The existing implementation calculates mclk rate as function
of audio sample rate multiplied to multiplier taken from Table 5.
However this is not accurate for Manual Setting Mode - tables 3 & 4 from
AK4458 RM defines rate (LRCK/FS) and frame width (MCLK/16fs..1152fs) ranges
as parameters to calculate mclk frequency. Aside of this - adjust
bclk:mclk ratio from machine driver as function of "compatible" id.Signed-off-by: Viorel Suman
(cherry picked from commit 527b8b7032dcb75c14bb2790330ab96743d83b16) -
Add output IOs defalut voltage set in device tree by add property like:
out-default = /bits/ 16 ;Reviewed-by: Haibo Chen
Signed-off-by: Fugang Duan -
support more codecs, codec is specified by compatible string
Signed-off-by: Shengjiu Wang
(cherry picked from commit 7c92a75fcf83ec0aa3fe6773e4cb5f5e88a1ff09) -
Add two new message command I2S_TX_POINTER and I2S_RX_POINTER,
which are used to get the hw pointer in m4 side. For in low
power audio mode, m4 won't send notification every period, the
notification only be sent when hw pointer reach end of buffer,
so we need these command to get the position of hw pointer,
user can use it to calculate the timestamp.Restructure send message and recv message together for i2s_rpmsg,
that every send message has a recv message. so the
i2s_send_message can store the recv message indepedently. one
reason is that the receive message is async withe send message.The low power audio is disabled in default, user need to enabled
it by add "fsl,enable-lpa" in dts.Signed-off-by: Shengjiu Wang
Reviewed-by: Viorel Suman
(cherry picked from commit 753e7b819609ad4791e32069a124d4411c720947) -
i.MX8QM/i.MX8QXP has pad type/definition change on B0, update
binding doc accordingly.Signed-off-by: Anson Huang
Reviewed-by: Robin Gong
(cherry picked from commit fd1e1f035e7cd2b0fd74549ba16172b5a10779cf) -
Using new "fsl,tx-d-cal" for dts, and update document accordingly.
Acked-by: Jun Li
Signed-off-by: Peter Chen -
Add a new property 'video-mode' binding for panel rm67191
which is used to specify a video data transfer mode.Signed-off-by: Fancy Fang
(cherry picked from commit 9dba8643d7b9c73a2b20ef517c79bb799f5ade3d) -
The resources retrieved by CAAM driver was wrong as the size
was not correct hence future uses might have issues.before:
[ 3.010744] caam 30900000.caam:
sm res: [start: 0000000000100000,
end: 0000000000107ffe,
name: /caam-sm@00100000,
flags:0x200 desc:0x0] -> size: 0x7fffmodif to actual size:
[ 3.012495] caam 30900000.caam:
sm res: [start: 0000000000100000,
end: 0000000000107fff,
name: /caam-sm@00100000,
flags:0x200 desc:0x0] -> size: 0x8000Signed-off-by: Franck LENORMAND
-
Signed-off-by: Franck LENORMAND
-
Signed-off-by: Franck LENORMAND
-
Enable CAAM driver for i.MX8 family:
- Use a Job ring for RNG instantiation rather than DECO, even
for i.MX6/7 families.
- Use of aliased CAAM registers instead of original registers in page 0
since page 0 is no more accessible in i.MX8 family except mScale.Signed-off-by: Aymen Sghaier
-
Signed-off-by: Franck LENORMAND
-
Add dts binding doc for i.MX8MM TMU.
Signed-off-by: Bai Ping
Reviewed-by: Anson Huang -
Use a specific compatible string for 850D in order to limit DSD MCLK
frequency for platforms newer than 850D.Signed-off-by: Viorel Suman
-
Add devicetree binding doc for i.MX8MM pinctrl driver.
Signed-off-by: Anson Huang
Reviewed-by: Bai Ping -
Add devicetree binding doc for i.MX8MQ pinctrl driver.
Signed-off-by: Anson Huang
Reviewed-by: Bai Ping -
i.MX8qxp uses two LDB(one primary, one auxiliary) to support dual
channel mode. This patch adds DT property descriptions for those
properties needed by this case.Signed-off-by: Liu Ying
-
specify the spdif in imx8mm for the ipg clock is higher that
it can support 192kHzSigned-off-by: Shengjiu Wang
Reviewed-by: Viorel Suman -
Add the device-tree bindings for the display bridge
Samsung MIPI DSIM on i.MX platforms.Signed-off-by: Fancy Fang
-
Add the device-tree bindings for the display node eLCDIF
on i.MX platforms.Signed-off-by: Fancy Fang
-
Add documentation for micfil IP.
Signed-off-by: Cosmin-Gabriel Samoila
-
Add new cell for sw_done/sw_done_selector, because PDM need enable
software done feature in sdma script.
The new fourth cell defined as below:
Bit31: sw_done
Bit15~bit0: selector
For example: 0x80000000 means sw_done enabled for done0 sector which
is for PDM on i.mx8mm.Signed-off-by: Robin Gong
Reviewed-by: Shengjiu Wang -
Add the pcie support for imx8mm and verify
it on imx8mm evk board when internal pll is
used as ref clock.Signed-off-by: Richard Zhu
-
enable rpmsg on imx8mm
Signed-off-by: Richard Zhu
