CONFIG_ARM=y

  CONFIG_SYS_THUMB_BUILD=y

  CONFIG_ARCH_VF610=y

  CONFIG_SYS_TEXT_BASE=0x3f401000

  CONFIG_ENV_SIZE=0x2000
  CONFIG_ENV_OFFSET=0xA0000

  CONFIG_DM_GPIO=y

  CONFIG_NR_DRAM_BANKS=1

  CONFIG_ENV_OFFSET_REDUND=0xC0000

  CONFIG_TARGET_PCM052=y

  CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/phytec/pcm052/imximage.cfg"

  CONFIG_BOOTDELAY=3

  CONFIG_BOARD_EARLY_INIT_F=y

  CONFIG_HUSH_PARSER=y

  CONFIG_CMD_BOOTZ=y

  CONFIG_CMD_MEMTEST=y

  CONFIG_CMD_GPIO=y
  CONFIG_CMD_I2C=y

  CONFIG_CMD_MMC=y

  CONFIG_CMD_NAND_TRIMFFS=y

  CONFIG_CMD_DHCP=y

  CONFIG_CMD_MII=y

  CONFIG_CMD_PING=y

  CONFIG_CMD_FAT=y

  CONFIG_MTDIDS_DEFAULT="nand0=NAND"
  CONFIG_MTDPARTS_DEFAULT="mtdparts=NAND:640k(bootloader),128k(env1),128k(env2),128k(dtb),6144k(kernel),-(root)"

  CONFIG_CMD_UBI=y

  CONFIG_OF_CONTROL=y

  CONFIG_DEFAULT_DEVICE_TREE="vf610-pcm052"

  CONFIG_ENV_IS_IN_NAND=y

  CONFIG_SYS_REDUNDAND_ENVIRONMENT=y

  CONFIG_SYS_RELOC_GD_ENV_ADDR=y

  CONFIG_DM=y
  CONFIG_VYBRID_GPIO=y

  CONFIG_DM_I2C=y
  CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
  CONFIG_I2C_DEFAULT_BUS_NUMBER=0x2
  CONFIG_SYS_I2C_MXC=y

  CONFIG_MISC=y

  CONFIG_I2C_EEPROM=y
  CONFIG_SYS_I2C_EEPROM_ADDR=0x50
  CONFIG_SYS_I2C_EEPROM_BUS=2
  CONFIG_SYS_EEPROM_SIZE=32768
  CONFIG_SYS_EEPROM_PAGE_WRITE_BITS=6
  CONFIG_SYS_I2C_EEPROM_ADDR_LEN=2
  CONFIG_DM_MMC=y

  CONFIG_FSL_ESDHC_IMX=y

  CONFIG_MTD=y

  CONFIG_DM_MTD=y

  CONFIG_NAND_VF610_NFC=y

  CONFIG_NAND_VF610_NFC_DT=y

  CONFIG_SYS_NAND_BUSWIDTH_16BIT=y

  CONFIG_DM_SPI_FLASH=y

  CONFIG_SPI_FLASH_STMICRO=y
  CONFIG_SPI_FLASH_MTD=y

  CONFIG_PHYLIB=y

  CONFIG_PHY_MICREL=y

  CONFIG_PHY_MICREL_KSZ8XXX=y

  CONFIG_DM_ETH=y
  CONFIG_FEC_MXC=y

  CONFIG_MII=y

  CONFIG_PINCTRL=y
  CONFIG_PINCTRL_VYBRID=y
  CONFIG_DM_RTC=y

  CONFIG_RTC_M41T62=y

  CONFIG_DM_SERIAL=y

  CONFIG_FSL_LPUART=y

  CONFIG_SPI=y
  CONFIG_DM_SPI=y
  CONFIG_FSL_QSPI=y
  # CONFIG_EFI_LOADER is not set