/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2019 NXP
 */

#ifndef __SMARCIMX8MP_H
#define __SMARCIMX8MP_H

#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>

#include "imx_env.h"


#define CONFIG_SPL_MAX_SIZE		(152 * 1024)
#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
#define CONFIG_SYS_UBOOT_BASE	(QSPI0_AMBA_BASE + CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512)

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_STACK		0x187FF0
#define CONFIG_SPL_BSS_START_ADDR      0x0095e000
#define CONFIG_SPL_BSS_MAX_SIZE        0x2000	/* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START    0x42200000
#define CONFIG_SYS_SPL_MALLOC_SIZE     SZ_512K	/* 512 KB */

#define CONFIG_MALLOC_F_ADDR		0x184000 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */

#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PCA9450

#define CONFIG_SYS_I2C

#endif

#define CONFIG_CMD_READ
#define CONFIG_SERIAL_TAG
#define CONFIG_FASTBOOT_USB_DEV 0

#define CONFIG_REMAKE_ELF
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_ETHPRIME                 "eth1" /* Set eqos to primary since we use its MDIO */

#define CONFIG_FEC_XCV_TYPE             RGMII
#define CONFIG_FEC_MXC_PHYADDR          6
#define FEC_QUIRK_ENET_MAC

#define DWC_NET_PHYADDR			6
#ifdef CONFIG_DWC_ETH_QOS
#define CONFIG_SYS_NONCACHED_MEMORY     (1 * SZ_1M)     /* 1M */
#endif

#define PHY_ANEG_TIMEOUT 20000

#endif

#define JAILHOUSE_ENV \
	"jh_clk= \0 " \
	"jh_mmcboot=setenv fdt_file imx8mp-smarc.dtb;" \
		"setenv jh_clk clk_ignore_unused; " \
			   "if run loadimage; then " \
				   "run mmcboot; " \
			   "else run jh_netboot; fi; \0" \
	"jh_netboot=setenv fdt_file imx8mp-smarc.dtb; setenv jh_clk clk_ignore_unused; run netboot; \0 "

#define CONFIG_MFG_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"emmc_dev=2\0"\
	"sd_dev=1\0" \


#ifdef CONFIG_NAND_BOOT
#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(nandboot),16m(nandfit),32m(nandkernel),16m(nanddtb),8m(nandtee),-(nandrootfs)"
#endif

/* Initial environment variables */
#if defined(CONFIG_NAND_BOOT)
#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	"splashimage=0x50000000\0" \
	"fdt_addr=0x43000000\0"			\
	"fdt_high=0xffffffffffffffff\0" \
	"mtdparts=" MFG_NAND_PARTITION "\0" \
	"console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200\0" \
	"bootargs=console=ttymxc1,115200 earlycon=ec_imx6q,0x30890000,115200 ubi.mtd=nandrootfs "  \
		"root=ubi0:nandrootfs rootfstype=ubifs "		     \
		MFG_NAND_PARTITION \
		"\0" \
	"bootcmd=nand read ${loadaddr} 0x5000000 0x2000000;"\
		"nand read ${fdt_addr} 0x7000000 0x100000;"\
		"booti ${loadaddr} - ${fdt_addr}"

#else
#define CONFIG_EXTRA_ENV_SETTINGS		\
	CONFIG_MFG_ENV_SETTINGS \
	JAILHOUSE_ENV \
	"script=boot.scr\0" \
	"image=Image\0" \
	"splashimage=0x50000000\0" \
	"m4_bin=hello_world.bin\0" \
	"use_m4=no\0" \
	"console=ttymxc1,115200\0" \
	"fdt_addr=0x43000000\0"			\
	"fdt_high=0xffffffffffffffff\0"		\
	"boot_fit=no\0" \
	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	"initrd_addr=0x43800000\0"		\
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"usbroot=/dev/sda2 rootwait ro\0" \
		"mmcrootfstype=ext4 rootwait\0" \
		"loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} uEnv.txt\0" \
		"loadusbbootenv=fatload usb 0:1 ${loadaddr} uEnv.txt\0" \
	"mmcautodetect=yes\0" \
		"importbootenv=echo Importing environment from mmc (uEnv.txt)...; " \
			"env import -t $loadaddr $filesize\0" \
		"importusbbootenv=echo Importing environment from USB (uEnv.txt)...; " \
	"mmcargs=setenv bootargs ${jh_clk} console=${console} ${optargs} " \
		"rootfstype=${mmcrootfstype} root=${mmcroot}\0 " \
		"usbargs=setenv bootargs ${jh_clk} console=${console} ${optargs} " \
		"rootfsusbtype=${usbrootfstype} root=${usbroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadm4bin=load mmc ${mmcdev}:${mmcpart} ${m4_addr_tmp} ${m4_bin}\0" \
	"loadusbimage=fatload usb 0:1 ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} /dtbs/${fdt_file}\0" \
	"loadusbfdt=fatload usb 0:1 ${fdt_addr} /dtbs/${fdt_file}\0" \
	"cpm4mem=cp.b ${m4_addr_tmp} ${m4_addr} 20000\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${boot_fit} = yes || test ${boot_fit} = try; then " \
			"bootm ${loadaddr}; " \
		"else " \
			"if run loadfdt; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"fi;\0" \
	"m4boot=" \
		"if test ${m4_addr} = 0x7e0000; then " \
			"echo Booting M4 from TCM; " \
		"else " \
			"echo Booting M4 from DRAM; " \
			"dcache flush; " \
		"fi; " \
		"bootaux ${m4_addr};\0" \
	"usbboot=echo Booting from USB ...; " \
		"run usbargs; " \
			"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
				"if run loadusbfdt; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
				"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
				"else " \
					"echo wait for boot; " \
				"fi;\0" \
	"netargs=setenv bootargs ${jh_clk} console=${console} " \
		"root=/dev/nfs " \
		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
		"run netargs;  " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${loadaddr} ${image}; " \
		"if test ${boot_fit} = yes || test ${boot_fit} = try; then " \
			"bootm ${loadaddr}; " \
		"else " \
			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
				"booti ${loadaddr} - ${fdt_addr}; " \
			"else " \
				"echo WARN: Cannot load the DT; " \
			"fi; " \
		"fi;\0"

#define CONFIG_BOOTCOMMAND \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
		"if test ${use_m4} = yes && run loadm4bin; then " \
			"run cpm4mem; " \
			"run m4boot; " \
		"fi; " \
		"echo Checking for: uEnv.txt ...; " \
			"if test -e mmc ${bootpart} /uEnv.txt; then " \
				"if run loadbootenv; then " \
					"echo Loaded environment from uEnv.txt;" \
					"run importbootenv;" \
				"fi;" \
				"echo Checking if uenvcmd is set ...;" \
				"if test -n ${uenvcmd}; then " \
					"echo Running uenvcmd ...;" \
					"run uenvcmd;" \
				"fi;" \
			"fi; " \
			"if run loadimage; then " \
				"run mmcboot; " \
				"else run netboot; " \
			"fi; " \
		"fi;"
#endif

/* Link Definitions */
#define CONFIG_LOADADDR			0x40480000

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR

#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE	0x80000
#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED

#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		SZ_32M

/* Totally 4GB/6GB DDR (2+2/4+4) */
#define CONFIG_SYS_SDRAM_BASE		0x40000000
#define PHYS_SDRAM			0x40000000
#ifdef CONFIG_4GB_LPDDR4
#define PHYS_SDRAM_SIZE			0xc0000000	/* 3 GB */
#else
#define PHYS_SDRAM_SIZE			0xc0000000	/* 3 GB */
#endif
#define PHYS_SDRAM_2			0x100000000
#ifdef CONFIG_TARGET_IMX8MP_DDR4_EVK
#define PHYS_SDRAM_2_SIZE		0x40000000	/* 1 GB */
#else
#ifdef CONFIG_4GB_LPDDR4
#define PHYS_SDRAM_2_SIZE		0x40000000	/* 1 GB */
#else
#define PHYS_SDRAM_2_SIZE		0xc0000000	/* 3 GB */
#endif
#endif

#define CONFIG_SYS_MEMTEST_START	0x60000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + \
					(PHYS_SDRAM_SIZE >> 1))

#ifdef CONFIG_CONSOLE_SER0
#define CONFIG_MXC_UART_BASE            UART1_BASE_ADDR
#define CONSOLE_DEV                     "ttymxc0"
#endif

#ifdef CONFIG_CONSOLE_SER1
#define CONFIG_MXC_UART_BASE            UART4_BASE_ADDR
#define CONSOLE_DEV                     "ttymxc3"
#endif

#ifdef CONFIG_CONSOLE_SER2
#define CONFIG_MXC_UART_BASE            UART3_BASE_ADDR
#define CONSOLE_DEV                     "ttymxc2"
#endif

#ifdef CONFIG_CONSOLE_SER3
#define CONFIG_MXC_UART_BASE            UART2_BASE_ADDR
#define CONSOLE_DEV                     "ttymxc1"
#endif

/* Monitor Command Prompt */
#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
#define CONFIG_SYS_CBSIZE		2048
#define CONFIG_SYS_MAXARGS		64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)

#define CONFIG_IMX_BOOTAUX
#define CONFIG_FSL_USDHC

#ifdef CONFIG_TARGET_IMX8MP_DDR4_EVK
#define CONFIG_SYS_FSL_USDHC_NUM	1
#else
#define CONFIG_SYS_FSL_USDHC_NUM	2
#endif
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

#define CONFIG_CMD_PART
#define CONFIG_CMD_FS_GENERIC

#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#ifdef CONFIG_FSL_FSPI
#define FSL_FSPI_FLASH_SIZE		SZ_32M
#define FSL_FSPI_FLASH_NUM		1
#define FSPI0_BASE_ADDR			0x30bb0000
#define FSPI0_AMBA_BASE			0x0
#define CONFIG_FSPI_QUAD_SUPPORT

#define CONFIG_SYS_FSL_FSPI_AHB
#endif

#ifdef CONFIG_NAND_MXS
#define CONFIG_CMD_NAND_TRIMFFS

/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE     1
#define CONFIG_SYS_NAND_BASE           0x20000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_USE_FLASH_BBT
#endif /* CONFIG_NAND_MXS */

#define CONFIG_SYS_I2C_SPEED		100000

/* USB configs */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE

#define CONFIG_USBD_HS

#define CONFIG_CMD_USB_MASS_STORAGE
#define CONFIG_USB_GADGET_MASS_STORAGE
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#endif

#define CONFIG_USB_MAX_CONTROLLER_COUNT         2
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_VBUS_DRAW 2

#ifdef CONFIG_DM_VIDEO
#define CONFIG_VIDEO_LOGO
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_BMP_24BPP
#define CONFIG_BMP_32BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#endif

#ifdef CONFIG_ANDROID_SUPPORT
#include "smarcimx8mp_android.h"
#endif

#endif