zynq-common.h
6.29 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
/*
* (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
* (C) Copyright 2013 Xilinx, Inc.
*
* Common configuration options for all Zynq boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_ZYNQ_COMMON_H
#define __CONFIG_ZYNQ_COMMON_H
/* High Level configuration Options */
#define CONFIG_ARMV7
#define CONFIG_ZYNQ
/* CPU clock */
#ifndef CONFIG_CPU_FREQ_HZ
# define CONFIG_CPU_FREQ_HZ 800000000
#endif
/* Cache options */
#define CONFIG_CMD_CACHE
#define CONFIG_SYS_CACHELINE_SIZE 32
#define CONFIG_SYS_L2CACHE_OFF
#ifndef CONFIG_SYS_L2CACHE_OFF
# define CONFIG_SYS_L2_PL310
# define CONFIG_SYS_PL310_BASE 0xf8f02000
#endif
/* Serial drivers */
#define CONFIG_BAUDRATE 115200
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
/* Zynq Serial driver */
#ifdef CONFIG_ZYNQ_SERIAL_UART0
# define CONFIG_ZYNQ_SERIAL_BASEADDR0 0xE0000000
# define CONFIG_ZYNQ_SERIAL_BAUDRATE0 CONFIG_BAUDRATE
# define CONFIG_ZYNQ_SERIAL_CLOCK0 50000000
#endif
#ifdef CONFIG_ZYNQ_SERIAL_UART1
# define CONFIG_ZYNQ_SERIAL_BASEADDR1 0xE0001000
# define CONFIG_ZYNQ_SERIAL_BAUDRATE1 CONFIG_BAUDRATE
# define CONFIG_ZYNQ_SERIAL_CLOCK1 50000000
#endif
#if defined(CONFIG_ZYNQ_SERIAL_UART0) || defined(CONFIG_ZYNQ_SERIAL_UART1)
# define CONFIG_ZYNQ_SERIAL
#endif
/* DCC driver */
#if defined(CONFIG_ZYNQ_DCC)
# define CONFIG_ARM_DCC
# define CONFIG_CPU_V6 /* Required by CONFIG_ARM_DCC */
#endif
/* Ethernet driver */
#if defined(CONFIG_ZYNQ_GEM0) || defined(CONFIG_ZYNQ_GEM1)
# define CONFIG_NET_MULTI
# define CONFIG_ZYNQ_GEM
# define CONFIG_MII
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_PHYLIB
# define CONFIG_PHY_MARVELL
#endif
/* SPI */
#ifdef CONFIG_ZYNQ_SPI
# define CONFIG_SPI_FLASH
# define CONFIG_SPI_FLASH_SST
# define CONFIG_CMD_SF
#endif
/* NOR */
#ifndef CONFIG_SYS_NO_FLASH
# define CONFIG_SYS_FLASH_BASE 0xE2000000
# define CONFIG_SYS_FLASH_SIZE (16 * 1024 * 1024)
# define CONFIG_SYS_MAX_FLASH_BANKS 1
# define CONFIG_SYS_MAX_FLASH_SECT 512
# define CONFIG_SYS_FLASH_ERASE_TOUT 1000
# define CONFIG_SYS_FLASH_WRITE_TOUT 5000
# define CONFIG_FLASH_SHOW_PROGRESS 10
# define CONFIG_SYS_FLASH_CFI
# undef CONFIG_SYS_FLASH_EMPTY_INFO
# define CONFIG_FLASH_CFI_DRIVER
# undef CONFIG_SYS_FLASH_PROTECTION
# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#endif
/* MMC */
#if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
# define CONFIG_MMC
# define CONFIG_GENERIC_MMC
# define CONFIG_SDHCI
# define CONFIG_ZYNQ_SDHCI
# define CONFIG_CMD_MMC
# define CONFIG_CMD_FAT
# define CONFIG_SUPPORT_VFAT
# define CONFIG_CMD_EXT2
# define CONFIG_DOS_PARTITION
#endif
/* I2C */
#if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
# define CONFIG_CMD_I2C
# define CONFIG_SYS_I2C
# define CONFIG_SYS_I2C_ZYNQ
# define CONFIG_SYS_I2C_ZYNQ_SPEED 100000
# define CONFIG_SYS_I2C_ZYNQ_SLAVE 1
#endif
/* EEPROM */
#ifdef CONFIG_ZYNQ_EEPROM
# define CONFIG_CMD_EEPROM
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
# define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
# define CONFIG_SYS_EEPROM_SIZE 1024 /* Bytes */
#endif
#define CONFIG_BOOTP_SERVERIP
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_MAY_FAIL
/* Total Size of Environment Sector */
#define CONFIG_ENV_SIZE (128 << 10)
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* Environment */
#ifndef CONFIG_ENV_IS_NOWHERE
# ifndef CONFIG_SYS_NO_FLASH
# define CONFIG_ENV_IS_IN_FLASH
# elif defined(CONFIG_SYS_NO_FLASH)
# define CONFIG_ENV_IS_NOWHERE
# endif
# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
# define CONFIG_ENV_OFFSET 0xE0000
# define CONFIG_CMD_SAVEENV
#endif
/* Default environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
"fit_image=fit.itb\0" \
"load_addr=0x2000000\0" \
"fit_size=0x800000\0" \
"flash_off=0x100000\0" \
"nor_flash_off=0xE2100000\0" \
"fdt_high=0x20000000\0" \
"initrd_high=0x20000000\0" \
"norboot=echo Copying FIT from NOR flash to RAM... && " \
"cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
"bootm ${load_addr}\0" \
"sdboot=echo Copying FIT from SD to RAM... && " \
"fatload mmc 0 ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0" \
"jtagboot=echo TFTPing FIT to RAM... && " \
"tftp ${load_addr} ${fit_image} && " \
"bootm ${load_addr}\0"
#define CONFIG_BOOTCOMMAND "run $modeboot"
#define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */
#define CONFIG_SYS_LOAD_ADDR 0 /* default? */
/* Miscellaneous configurable options */
#define CONFIG_SYS_PROMPT "zynq-uboot> "
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_MAXARGS 15 /* max number of command args */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
/* Physical Memory map */
#define CONFIG_SYS_TEXT_BASE 0x4000000
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE 0
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + 0x1000)
#define CONFIG_SYS_MALLOC_LEN 0x400000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_MALLOC_LEN
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
/* Enable the PL to be downloaded */
#define CONFIG_FPGA
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_ZYNQPL
#define CONFIG_CMD_FPGA
/* Open Firmware flat tree */
#define CONFIG_OF_LIBFDT
/* FIT support */
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
/* FDT support */
#define CONFIG_OF_CONTROL
#define CONFIG_OF_SEPARATE
#define CONFIG_DISPLAY_BOARDINFO_LATE
/* RSA support */
#define CONFIG_FIT_SIGNATURE
#define CONFIG_RSA
/* Boot FreeBSD/vxWorks from an ELF image */
#if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
# define CONFIG_API
# define CONFIG_CMD_ELF
# define CONFIG_SYS_MMC_MAX_DEVICE 1
#endif
/* Commands */
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#endif /* __CONFIG_ZYNQ_COMMON_H */