/*
 * Copyright (C) 2015 Freescale Semiconductor, Inc.
 * Copyright 2017-2018 NXP
 *
 * Configuration settings for the Freescale i.MX7D SABRESD board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __SMARCFIMX7_CONFIG_H
#define __SMARCFIMX7_CONFIG_H

#include "mx7smarc_common.h"
#include "imx_env.h"

#define CONFIG_DBG_MONITOR

#if defined(CONFIG_MX7D)
#if defined(CONFIG_2GDDR3)
#define PHYS_SDRAM_SIZE                 SZ_2G
#else
#define PHYS_SDRAM_SIZE                 SZ_1G
#endif
#else
#define PHYS_SDRAM_SIZE                 SZ_512M
#endif

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(32 * SZ_1M)

/* Network */
#ifdef CONFIG_DM_ETH
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define CONFIG_FEC_XCV_TYPE             RGMII
#define CONFIG_FEC_ENET_DEV		0

#define CONFIG_PHY_ATHEROS
/* ENET1 */
#if (CONFIG_FEC_ENET_DEV == 0)
#define IMX_FEC_BASE			ENET_IPS_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR          0x6
#define CONFIG_ETHPRIME                 "eth0"
#elif (CONFIG_FEC_ENET_DEV == 1)
#define IMX_FEC_BASE			ENET2_IPS_BASE_ADDR
#define CONFIG_FEC_MXC_PHYADDR          0x7
#define CONFIG_ETHPRIME                 "eth1"
#endif

#define CONFIG_FEC_MXC_MDIO_BASE	ENET_IPS_BASE_ADDR
#endif

/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR       0

#undef CONFIG_BOOTM_NETBSD
#undef CONFIG_BOOTM_PLAN9
#undef CONFIG_BOOTM_RTEMS

#define CONFIG_CMD_IMPORTENV

/* I2C configs */
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2
#define CONFIG_SYS_I2C_SPEED		100000

#define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
#define CONFIG_SYS_MMC_IMG_LOAD_PART	1

#ifdef CONFIG_SPI_BOOT
#define CONFIG_MXC_SPI
#define CONFIG_ENV_IS_IN_SPI_FLASH
#elif defined CONFIG_NAND_BOOT
#define CONFIG_NAND_MXS
#define CONFIG_ENV_IS_IN_NAND
#else
#define CONFIG_ENV_IS_IN_MMC
#endif

#ifdef 	CONFIG_MXC_SPI
#define CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_MACRONIX
#define CONFIG_SF_DEFAULT_BUS          2
#define CONFIG_SF_DEFAULT_CS           0	/* Use SPI2 SS0 as chip select */
#define CONFIG_SF_DEFAULT_SPEED 20000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
#endif

#ifdef CONFIG_IMX_BOOTAUX

#ifdef CONFIG_FSL_QSPI
#define UPDATE_M4_ENV \
	"m4image=m4_qspi.bin\0" \
	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4image}\0" \
	"update_m4_from_sd=" \
		"if sf probe 1:0; then " \
			"if run loadm4image; then " \
				"setexpr fw_sz ${filesize} + 0xffff; " \
				"setexpr fw_sz ${fw_sz} / 0x10000; "	\
				"setexpr fw_sz ${fw_sz} * 0x10000; "	\
				"sf erase 0x100000 ${fw_sz}; " \
				"sf write ${loadaddr} 0x100000 ${filesize}; " \
			"fi; " \
		"fi\0" \
	"m4boot=sf probe 1:0; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
#else
#define UPDATE_M4_ENV \
	"m4image=m4_qspi.bin\0" \
	"loadm4image=fatload mmc ${mmcdev}:${mmcpart} "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)" ${m4image}\0" \
	"m4boot=run loadm4image; bootaux "__stringify(CONFIG_SYS_AUXCORE_BOOTDATA)"\0"
#endif
#else
#define UPDATE_M4_ENV ""
#endif

#ifdef CONFIG_NAND_BOOT
#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(nandboot),16m(nandkernel),16m(nanddtb),16m(nandtee),-(nandrootfs) "
#else
#define MFG_NAND_PARTITION ""
#endif

#define CONFIG_CMD_READ
#define CONFIG_SERIAL_TAG
#define CONFIG_FASTBOOT_USB_DEV 0

#define CONFIG_MFG_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
	"initrd_addr=0x86800000\0" \
	"initrd_high=0xffffffff\0" \
	"emmc_dev=1\0"\
	"sd_dev=0\0" \
	"mtdparts=" MFG_NAND_PARTITION \
	"\0"\

#define CONFIG_DFU_ENV_SETTINGS \
	"dfu_alt_info=image raw 0 0x800000;"\
		"u-boot raw 0 0x4000;"\
		"bootimg part 0 1;"\
		"rootfs part 0 2\0" \

#if defined(CONFIG_NAND_BOOT)
#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	TEE_ENV \
	"panel=TFT43AB\0" \
	"fdt_addr=0x83000000\0" \
	"fdt_high=0xffffffff\0"	  \
	"console=ttymxc0\0" \
	"bootargs=console=ttymxc0,115200 ubi.mtd=4 "  \
		"root=ubi0:nandrootfs rootfstype=ubifs "		     \
		MFG_NAND_PARTITION \
		"\0" \
	"bootcmd=nand read ${loadaddr} 0x4000000 0x800000;"\
		"nand read ${fdt_addr} 0x5000000 0x100000;"\
		"if test ${tee} = yes; then " \
			"nand read ${tee_addr} 0x6000000 0x400000;"\
			"bootm ${teeaddr} - ${fdt_addr};" \
		"else " \
			"bootz ${loadaddr} - ${fdt_addr};" \
		"fi\0"

#else
#define CONFIG_EXTRA_ENV_SETTINGS \
	UPDATE_M4_ENV \
	CONFIG_MFG_ENV_SETTINGS \
	TEE_ENV \
	CONFIG_DFU_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=zImage\0" \
       	"console=" CONSOLE_DEV "\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
       "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	"fdt_addr=0x83000000\0" \
	"tee_addr=0x84000000\0" \
	"tee_file=uTee-7dsdb\0" \
       	"ethprime=eth0\0" \
       	"ipaddr=192.168.1.60\0" \
	"boot_fdt=try\0" \
	"ip_dyn=yes\0" \
       	"panel=G070VW01\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcrootfstype=ext4 rootwait\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console},${baudrate} " \
               	"${optargs} " \
               	"rootfstype=${mmcrootfstype} " \
		"root=${mmcroot}\0" \
       	"loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} uEnv.txt\0" \
       	"importbootenv=echo Importing environment from mmc (uEnv.txt)...; " \
               	"env import -t $loadaddr $filesize\0" \
	"loadbootscript=" \
		"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
		"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
       	"loadzimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
      	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} /dtbs/${fdt_file}\0" \
	"loadtee=fatload mmc ${mmcdev}:${mmcpart} ${tee_addr} ${tee_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"if test ${tee} = yes; then " \
			"run loadfdt; run loadtee; bootm ${tee_addr} - ${fdt_addr}; " \
		"else " \
			"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
				"if run loadfdt; then " \
					"bootz ${loadaddr} - ${fdt_addr}; " \
				"else " \
					"if test ${boot_fdt} = try; then " \
						"bootz; " \
					"else " \
						"echo WARN: Cannot load the DT; " \
					"fi; " \
				"fi; " \
			"else " \
				"bootz; " \
			"fi; " \
		"fi;\0" \
	"netargs=setenv bootargs console=${console},${baudrate} " \
		"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
		"netboot=echo Booting from net ...; " \
		"run netargs; " \
		"if test ${ip_dyn} = yes; then " \
			"setenv get_cmd dhcp; " \
		"else " \
			"setenv get_cmd tftp; " \
		"fi; " \
		"${get_cmd} ${image}; " \
		"if test ${tee} = yes; then " \
			"${get_cmd} ${tee_addr} ${tee_file}; " \
			"${get_cmd} ${fdt_addr} ${fdt_file}; " \
			"bootm ${tee_addr} - ${fdt_addr}; " \
		"else " \
			"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
				"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
					"bootz ${loadaddr} - ${fdt_addr}; " \
				"else " \
					"if test ${boot_fdt} = try; then " \
						"bootz; " \
					"else " \
						"echo WARN: Cannot load the DT; " \
					"fi; " \
				"fi; " \
			"else " \
				"bootz; " \
			"fi; " \
		"fi;\0" \
		"findfdt="\
			"if test $fdt_file = undefined; then " \
				"setenv fdt_file imx7d-sdb.dtb; " \
			"fi;\0" \

#define CONFIG_BOOTCOMMAND \
	   "run findfdt;" \
	   "mmc dev ${mmcdev};" \
	   "mmc dev ${mmcdev}; if mmc rescan; then " \
               	"echo SD/MMC found on device ${mmcdev};" \
               	"if run loadbootenv; then " \
                       	"run importbootenv;" \
               	"fi;" \
               	"echo Checking if uenvcmd is set ...;" \
               	"if test -n $uenvcmd; then " \
                       	"echo Running uenvcmd ...;" \
                       	"run uenvcmd;" \
               	"fi;" \
               	"echo Running default loadzimage ...;" \
               	"if run loadzimage; then " \
                       	"run loadfdt;" \
                       	"run mmcboot;" \
               	"fi;" \
       	"else run netboot; fi"
#endif

#define CONFIG_SYS_MEMTEST_START	0x80000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x20000000)

#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
#define CONFIG_SYS_HZ			1000

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* environment organization */
#define CONFIG_ENV_SIZE			SZ_8K

#if defined(CONFIG_ENV_IS_IN_MMC)
#define CONFIG_ENV_OFFSET		(14 * SZ_64K)
#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
#define CONFIG_ENV_OFFSET		(896 * 1024)
#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
#define CONFIG_ENV_SPI_BUS		CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS		CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE		CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ		CONFIG_SF_DEFAULT_SPEED
#elif defined(CONFIG_ENV_IS_IN_NAND)
#undef CONFIG_ENV_SIZE
#define CONFIG_ENV_OFFSET		(60 << 20)
#define CONFIG_ENV_SECT_SIZE		(128 << 10)
#define CONFIG_ENV_SIZE			CONFIG_ENV_SECT_SIZE
#endif

#ifdef CONFIG_FSL_QSPI
#define CONFIG_SYS_AUXCORE_BOOTDATA 0x60100000 /* Set to QSPI1 A flash, offset 1M */
#else
#define CONFIG_SYS_AUXCORE_BOOTDATA 0x7F8000 /* Set to TCML address */
#endif
/*
 * If want to use nand, define CONFIG_CMD_NAND and rework board
 * to support nand, since emmc has pin conflicts with nand
 */
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_MXS
#define CONFIG_CMD_NAND_TRIMFFS

/* NAND stuff */
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION

/* DMA stuff, needed for GPMI/MXS NAND support */
#define CONFIG_APBH_DMA
#define CONFIG_APBH_DMA_BURST
#define CONFIG_APBH_DMA_BURST8
#endif

#ifdef CONFIG_NAND_MXS
#define CONFIG_SYS_FSL_USDHC_NUM	1
#else
#define CONFIG_SYS_FSL_USDHC_NUM	2
#endif

/* MMC Config*/
#define CONFIG_SYS_FSL_ESDHC_ADDR       0
#define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC3 */
#define CONFIG_SYS_MMC_ENV_PART		0	/* user area */
#define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC3 */

/* USB Configs */
#define CONFIG_MXC_USB_PORTSC  (PORT_PTS_UTMI | PORT_PTS_PTW)

#define CONFIG_IMX_THERMAL

#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_MXS
#define CONFIG_VIDEO_LOGO
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IMX_VIDEO_SKIP
#endif

/* #define CONFIG_SPLASH_SCREEN*/
/* #define CONFIG_MXC_EPDC*/

/*
 * SPLASH SCREEN Configs
 */
#if defined(CONFIG_MXC_EPDC)
/*
 * Framebuffer and LCD
 */
#define CONFIG_CMD_BMP
#define CONFIG_SPLASH_SCREEN

#undef LCD_TEST_PATTERN
/* #define CONFIG_SPLASH_IS_IN_MMC			1 */
#define LCD_BPP					LCD_MONOCHROME
/* #define CONFIG_SPLASH_SCREEN_ALIGN		1 */

#define CONFIG_WAVEFORM_BUF_SIZE		0x400000
#endif

#if defined(CONFIG_MXC_EPDC) && defined(CONFIG_FSL_QSPI)
#error "EPDC Pins conflicts QSPI, Either EPDC or QSPI can be enabled!"
#endif

#ifdef CONFIG_FSL_QSPI
#define CONFIG_SYS_FSL_QSPI_AHB
#define CONFIG_SF_DEFAULT_BUS		1 /* SOFT SPI occupies the BUS 0, so change the QSPI1 to BUS 1*/
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		40000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0
#define FSL_QSPI_FLASH_NUM		1
#define FSL_QSPI_FLASH_SIZE		SZ_64M
#define QSPI0_BASE_ADDR			QSPI1_IPS_BASE_ADDR
#define QSPI0_AMBA_BASE			QSPI0_ARB_BASE_ADDR
#endif

#if defined(CONFIG_ANDROID_SUPPORT)
#include "smarcfimx7android.h"
#elif defined(CONFIG_ANDROID_THINGS_SUPPORT)
#include "smarcfimx7_androidthings.h"
#else
#define CONFIG_USBD_HS
#endif

#endif	/* __CONFIG_H */