snapper9g45.h
3.43 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
/*
* Bluewater Systems Snapper 9G45 module
*
* (C) Copyright 2011 Bluewater Systems
* Author: Andre Renaud <andre@bluewatersys.com>
* Author: Ryan Mallon <ryan@bluewatersys.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* SoC type is defined in boards.cfg */
#include <asm/hardware.h>
#include <linux/sizes.h>
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
/* CPU */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT_ONLY
/* SDRAM */
#define CONFIG_NR_DRAM_BANKS 1
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS6
#define CONFIG_SYS_SDRAM_SIZE (128 * 1024 * 1024) /* 64MB */
#define CONFIG_SYS_INIT_SP_ADDR (ATMEL_BASE_SRAM + 0x1000 - \
GENERATED_GBL_DATA_SIZE)
/* Mem test settings */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_SDRAM_BASE + (1024 * 1024))
/* NAND Flash */
#define CONFIG_NAND_ATMEL
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_SYS_NAND_ECC_BASE ATMEL_BASE_ECC
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
#define CONFIG_SYS_NAND_DBW_8
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21) /* AD21 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22) /* AD22 */
#define CONFIG_SYS_NAND_ENABLE_PIN AT91_PIN_PC14
#define CONFIG_SYS_NAND_READY_PIN AT91_PIN_PC8
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
#define CONFIG_TFTP_PORT
#define CONFIG_TFTP_TSIZE
/* MMC */
#define CONFIG_GENERIC_ATMEL_MCI
/* LCD */
#define CONFIG_ATMEL_LCD
#define CONFIG_GURNARD_SPLASH
#define CONFIG_ATMEL_SPI
/* GPIOs and IO expander */
#define CONFIG_ATMEL_LEGACY
#define CONFIG_AT91_GPIO
#define CONFIG_AT91_GPIO_PULLUP 1
/* UARTs/Serial console */
#define CONFIG_ATMEL_USART
/* Boot options */
#define CONFIG_SYS_LOAD_ADDR 0x23000000
#define CONFIG_BOOTP_BOOTFILESIZE
/* Environment settings */
#define CONFIG_ENV_OFFSET (512 << 10)
#define CONFIG_ENV_SIZE (256 << 10)
#define CONFIG_ENV_OVERWRITE
#define CONFIG_EXTRA_ENV_SETTINGS \
"ethaddr=00:00:00:00:00:00\0" \
"serial=0\0" \
"stdout=serial_atmel\0" \
"stderr=serial_atmel\0" \
"stdin=serial_atmel\0" \
"bootlimit=3\0" \
"loadaddr=0x71000000\0" \
"board_rev=2\0" \
"bootfile=/tftpboot/uImage\0" \
"bootargs_def=console=ttyS0,115200 panic=5 quiet lpj=997376\0" \
"nfsroot=/export/root\0" \
"boot_working=setenv bootargs $bootargs_def; nboot $loadaddr 0 0x20c0000 && bootm\0" \
"boot_safe=setenv bootargs $bootargs_def; nboot $loadaddr 0 0xc0000 && bootm\0" \
"boot_tftp=setenv bootargs $bootargs_def ip=any nfsroot=$nfsroot; setenv autoload y && bootp && bootm\0" \
"boot_usb=setenv bootargs $bootargs_def; usb start && usb storage && fatload usb 0:1 $loadaddr dds-xm200.bin && bootm\0" \
"boot_mmc=setenv bootargs $bootargs_def; mmc rescan && fatload mmc 0:1 $loadaddr dds-xm200.bin && bootm\0" \
"bootcmd=run boot_mmc ; run boot_usb ; run boot_working ; run boot_safe\0" \
"altbootcmd=run boot_mmc ; run boot_usb ; run boot_safe ; run boot_working\0"
/* Console settings */
/* U-Boot memory settings */
#define CONFIG_SYS_MALLOC_LEN (1 << 20)
/* Command line configuration */
#define CONFIG_CMD_MII
#define CONFIG_CMD_MMC
#define CONFIG_CMD_CACHE
#endif /* __CONFIG_H */