20 Mar, 2009
1 commit
-
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.Acked-by: Tony Lindgren
Signed-off-by: Russell King
19 Mar, 2009
1 commit
-
Conflicts:
arch/arm/mach-omap2/clock.c
18 Mar, 2009
1 commit
-
…s/linux-2.6 into devel
17 Mar, 2009
5 commits
-
Signed-off-by: Krzysztof Hałasa
-
Signed-off-by: Krzysztof Hałasa
-
Signed-off-by: Krzysztof Hałasa
-
Map unused registers at the end of DMA region at 64 MB to allow PCI masters
to cross the boundary when prefetching data from SDRAM.Signed-off-by: Krzysztof Hałasa
-
Conflicts:
drivers/video/mx3fb.c
16 Mar, 2009
5 commits
-
Since now ipaq_model_ops used only for accessing h3600 EGPIOs,
drop it completely and use assign_h3600_egpio() directly.Signed-off-by: Dmitry Artamonow
Signed-off-by: Russell King -
Replace all occurences with assign_h3600_egpio.
Also simplify code a bit by replacing couple of if-else
statements with one-line equivalents.Signed-off-by: Dmitry Artamonow
Signed-off-by: Russell King -
Remove unused fields and associated funtions-accesors.
Signed-off-by: Dmitry Artamonow
Signed-off-by: Russell King -
Right now iPaq h3600's default MTD partitions table is a mess. It has
two #ifdefs with #else, giving total 3 variants, depending on your
kernel config. Replace all this with simple two-partitions scheme
(bootloader + rootfs), that used by both shipped WindowsCE and
most of the linux distributions (Familiar, Angstrom)Signed-off-by: Dmitry Artamonow
Signed-off-by: Russell King -
There's no actual code for iPAQ sleeves support in kernel that depends
on this config option.Signed-off-by: Dmitry Artamonow
Signed-off-by: Russell King
15 Mar, 2009
1 commit
-
…-linux-2.6 into devel
14 Mar, 2009
1 commit
-
Conflicts:
arch/arm/mach-at91/gpio.c
13 Mar, 2009
25 commits
-
This patch adds basic support for Dave/DENX QongEVB-LITE i.MX31-based
board. It includes support for clocks initialization, UART1, NOR-flash,
FPGA-attached NAND flash and DNET ethernet controller (inside FPGA).Signed-off-by: Ilya Yanok
Signed-off-by: Sascha Hauer -
Signed-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
Signed-of-by: Julien Boibessot
Signed-off-by: Sascha Hauer -
Rename driver from imx-mmc to mxc-mmc to avoid conflicts with the
mx1 mmc driver.Signed-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
This patch adds clkdev support for i.MX31. This is done in a
similar way done previously for i.MX27Signed-off-by: Sascha Hauer
-
The UART3 had a copy-paste bug. instead of claiming rxd, txd, rts and
cts pins, cts and rts were claimed twiceSigned-off-by: Sascha Hauer
-
On MX31 we can't do much without mapping the AIPS1/2 register space.
Move these mappings from individual boards to plat-mxc/mm.cSigned-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
The i.MX35 basically features the same peripherals as the i.MX31 with
some differences:- The i.MX35 has a FEC ethernet controller
- The NAND controller base addresses are different
- The i.MX35 has only 3 UARTsSigned-off-by: Sascha Hauer
-
This patch adds clock support for i.MX35 SoCs. We do not support setting
of clock rates yet, but most interesting clock rates should be reported.
I couldn't test all clock rates and the datasheet contains some obvious
bugs, so expect some bugs in this code.Signed-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
We had hardcoded cpu_is_ macros for mxc architectures till now. As we
want to run the same kernel on i.MX31 and i.MX35 this patch adds cpu_is_
macros which expand to 0 or 1 if only one architecture is compiled in and
only check for the cpu type if more than one architecture is compiled
in.Signed-off-by: Sascha Hauer
-
This patch moves the stuff common to i.MX31 and i.MX35 to mx3x.h and the
specifics to mx31.h/mx35.h. We can build a kernel which runs on i.MX31 and
i.MX35, so always include mx31.h and mx35.hSigned-off-by: Sascha Hauer
-
The var->hsync_len, var->right_margin and var->left_margin fields
should contain the real values, not the hardware dependent values.Signed-off-by: Sascha Hauer
-
Signed-off-by: Sascha Hauer
-
This adds the dma (ipu_dma) and fb devices for the mx31 for which drivers now are
available.v2: merge the ipu and fb device in the same patch as suggested by Sascha
Signed-off-by: Valentin Longchamp
Signed-off-by: Sascha Hauer -
This enables our mx31moboard to be used on the different baseboards that
we are developping according to the application needs. There are not
many differences between the boards for now, but when other peripherals
are available for mx31 the differences are going to grow.v2: takes Sascha's comments into account
Signed-off-by: Valentin Longchamp
Signed-off-by: Sascha Hauer -
Signed-off-by: Valentin Longchamp
Signed-off-by: Sascha Hauer -
Make sure not to create spurious pulses on GPIOs, when configuring them as
output: first set required level, then switch direction.Signed-off-by: Guennadi Liakhovetski
Signed-off-by: Sascha Hauer -
Signed-off-by: Holger Schurig
Signed-off-by: Sascha Hauer -
include devices.h from devices.c to avoid inconsistencies and to fix
sparse warningsSigned-off-by: Sascha Hauer
