30 Dec, 2008
40 commits
-
When the CX23418 CPU unit sent out an ack interrupt to the linux driver, it
also received that interrupt and cleared the flag before the linux driver could
see what the interrupt was for. This fix prevents the CPU from receiving an
IRQ for it's own outgoing ack's to the linux driver. This fix is critical now
that the linux driver doesn't poll but relies on these ack interrupts.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
Use the APU fw start address from rom file instead of a hardcoded entry vector.
Fixed cx18_setup_page() calls to use the correct APU image load addresses.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
All waits for cx18 mailbox API commands are now uninterruptable. Added
code to collect mailbox ack statistics. Tweaked timeouts based on collected
stats and video vertical frame and field rates.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
cx18: Improve handling of outgoing mailboxes detected to be busy. When
encountering a busy mailbox, sleep instead of polling, and wait for interrupt or
timeout. If the mailbox is still busy, force it free. When sending commands,
make sure we never create a situation where we mark the mailbox busy upon
sending, and ensure we always have a method to cleanly recover from a busy
mailbox.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
Driver interrupt and mailbox handling has change significantly.
Time for a roll to v1.0.2.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
Add mutexes to ensure exclusive access for outgoing driver to CX23418 mailboxes.
Also wait on a waitq for mailbox acknowledgement from the CX23418 instead of
polling.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
cx18: Use default kernel work queue; fix streaming flag for work handler.
Eliminate cx18 specific work queue and use the kernel default work queue.
Fixed the F_STREAMING_FLAG for the TS stream so cx18_dvb_work_handler()
can know when it is not safe to send MDLs to the firmware.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
Signed-off-by: Jean-Francois Moine
Signed-off-by: Mauro Carvalho Chehab -
cx18: Reduce number of mmio read retries to improve performance. Experiments
have shown 2 things: read retries never improve the result of a suspect mmio
read from the CX23418 (the result stays all 0xff's), and that most of the
suspected read failures are actually proper reads of values that should be
all 0xff's. This change reduces the number of read retries and keeps the
count separate from write retries.Signed-off-by: Andy Walls
Signed-off-by: Mauro Carvalho Chehab -
Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
incoming symbols and hence might run into problems at the very end of the
specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
running at 90MHz, raises lot of issues such as the need to recalculate
all of them , which is eventually very painful.Signed-off-by: Manu Abraham
Signed-off-by: Mauro Carvalho Chehab -
Signed-off-by: Manu Abraham
Signed-off-by: Mauro Carvalho Chehab -
Signed-off-by: Manu Abraham
Signed-off-by: Mauro Carvalho Chehab -
Print manufacturer/product info from USB device and also card entry.
Signed-off-by: Mauro Carvalho Chehab
-
Prints usb speed used by em28xx interface. While there, fixes USB ID's
endiannes.Signed-off-by: Mauro Carvalho Chehab
-
Signed-off-by: Mauro Carvalho Chehab
-
Several chips may be turned off when the device is not used, like audio,
video and dvb demods. This patch adds a gpio callback at the core
structs to allow turning off such devices.Signed-off-by: Mauro Carvalho Chehab
-
A previous changeset moved gpio from em28xx struct into em28xx_board.
However, the driver were not updated to properly honor those gpio's.Signed-off-by: Mauro Carvalho Chehab
-
Before this patch, several devices without tuner were kept the value 0
for tuner_type. However, this means TUNER_TEMIC_PAL. Replace those
entries for the proper TUNER_ABSENT value.Signed-off-by: Mauro Carvalho Chehab
-
Instead of using magic vmux/amux, let's use an alias where possible.
Signed-off-by: Mauro Carvalho Chehab
-
Instead of a large, ugly switch specifying the gpio tables for each
device, let's move it into the boards struct. This also helps to see
what boards have already the gpio's for DVB.Signed-off-by: Mauro Carvalho Chehab
-
Signed-off-by: Mauro Carvalho Chehab
-
Replaces all occurrences of em28xx_write_regs_req() and em28xx_write_reg()
used to setup register names by em28xx_write_reg().Also, documents the register names that are known.
This patch were generated by this small perl script:
my %reg_map = (
# Register table - the same as defined on parse_em28xx.pl script
);while (<>) {
if (m/(.*)em28xx_write_regs_req\(dev\,\s*0x00\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
my $reg = $2;
my $val = $3;
$val =~ tr/A-f/a-f/;
$reg = $reg_map{$reg} if defined($reg_map{$reg});
printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
} elsif (m/(.*)em28xx_write_regs\(dev\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
my $reg = $2;
my $val = $3;
$val =~ tr/A-f/a-f/;
$reg = $reg_map{$reg} if defined($reg_map{$reg});
printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
} else {
print $_;
}
}Signed-off-by: Mauro Carvalho Chehab
-
Signed-off-by: Mauro Carvalho Chehab
-
Now, the first message states board names. Also, removed printing the alternate
settings by default. I2C messages are now clearer.Signed-off-by: Mauro Carvalho Chehab
-
Since saa7115 has saa711x chip auto-detection, there's no need on differenciating
it at cards table. Just use the generic name for all boards that use a philips
saa711x decoder.Signed-off-by: Mauro Carvalho Chehab
-
Several fields are duplicated on both structs. Let's just copy em28xx_board instead.
A later cleanup could just copy the fields that are changed, in order to keep em28xx_board
const.Signed-off-by: Mauro Carvalho Chehab
-
Remove unused em28xx_board.vchannels and em28xx.video_channels.
Also, .is_em2800 = 0 is not needed, as all data is zeroed by kernel loader.The table also included a notice that svideo weren't test on Hauppauge
USB2. Remove this notice, since this input also works properly.Also, it does some whitespace cleanups.
Signed-off-by: Mauro Carvalho Chehab
-
The previous patches removed XCLK and I2C magic. Now, we finally know
what those registers do. Also, only a very few cards need different
setups for those.Instead of keeping the setups for those values inside the per-device
hack magic switch, move the uncommon values to the board-specific
struct, and have a common setup for all other boards.So, almost 100 lines of hacking magic were removed.
A co-lateral effect of this patch is that it also fixes a bug at em28xx-core, where xclk
were set, without taking any care about not overriding a previous xclk setup.Signed-off-by: Mauro Carvalho Chehab
-
Cleanup the calls to set the GPIOs and GPOs for various devices,
replacing the register number with the #define from em28xx-reg.h and
converting over to using em28xx_write_reg()Signed-off-by: Devin Heitmueller
Signed-off-by: Mauro Carvalho Chehab -
Convert over to setting the XCLK register usage with the new em28xx_write_reg()
function.Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet.
Signed-off-by: Devin Heitmueller
Signed-off-by: Mauro Carvalho Chehab -
This patch provides USB suspend and hibernation support
for Siano's SMS chipset based USB deviceSigned-off-by: Uri Shkolnik
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
Add function smsdvb_read_ucblocks to report uncorrectable error counts.
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
Enable power LED while the frontend is in use.
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
add USB IDs for Hauppauge WinTV MiniCard DVB-T
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
Signed-off-by: Michael Krufky
Signed-off-by: Mauro Carvalho Chehab -
On some em28xx devices, there's an unused interface. This is printed on
the logs as an error. We can just ignore that interface.Signed-off-by: Mauro Carvalho Chehab
-
Signed-off-by: Jean-Francois Moine
Signed-off-by: Mauro Carvalho Chehab -
The OmniVision OV534 is the USB bridge chip used in Sony Playstation EYE,
it is found also in other webcams like Hercules Blog Webcam and
Hercules Dualpix HD.
This driver is the port to gspca of a prototype driver by Mark Ferrell
based on vivi. The original code to initialize the camera and start the
capture is from Jim Paris on ps2dev.org, here integrated with the analysis
of the USB communications taken by the windows driver.Signed-off-by: Antonio Ospite
Signed-off-by: Jean-Francois Moine
Signed-off-by: Mauro Carvalho Chehab
