15 Sep, 2009
14 commits
-
pcnet_cs,serial_cs:
add cis of Linksys lan&modem mulitifunction pcmcia card
and some modem card(MT5634ZLX, RS-COM-2P).Signed-off-by: Ken Kawasaki
Signed-off-by: David S. Miller -
This patch fixes commit e36b9d16c6a6d0f59803b3ef04ff3c22c3844c10. The approach
there is to call dev_close()/dev_open() whenever the device type is changed in
order to remap the device IP multicast addresses to HW multicast addresses.
This approach suffers from 2 drawbacks:*. It assumes tha the device is UP when calling dev_close(), or otherwise
dev_close() has no affect. It is worth to mention that initscripts (Redhat)
and sysconfig (Suse) doesn't act the same in this matter.
*. dev_close() has other side affects, like deleting entries from the routing
table, which might be unnecessary.The fix here is to directly remap the IP multicast addresses to HW multicast
addresses for a bonding device that changes its type, and nothing else.Reported-by: Jason Gunthorpe
Signed-off-by: Moni Shoua
Signed-off-by: David S. Miller -
When using nanosleep() in an userspace application we get a ratelimit warning
NOHZ: local_softirq_pending 08
for 10 times.
The echo of CAN frames is done from process context and softirq context only.
Therefore the usage of netif_rx() was wrong (for years).This patch replaces netif_rx() with netif_rx_ni() which has to be used from
process/softirq context. It also adds a missing comment that can_send() must
no be used from hardirq context.Signed-off-by: Oliver Hartkopp
Signed-off-by: Urs Thuermann
Signed-off-by: David S. Miller -
In the case of fiber and serdes adapters we were seeing issues with ethtool
-t causing kernel panics due to null function pointers. To prevent this we
need to exit out of the phy reset code in the event that we do not have a
valid phy.Signed-off-by: Alexander Duyck
Signed-off-by: Don Skidmore
Signed-off-by: David S. Miller -
Our SGMII phy code was incomplete in that it was not actually placing the
phy in SGMII mode and as a result the PHY was not able to establish a link
when connected to a non serdes link partner. This patch updates the code
to combine the SGMII/serdes PCS init and to add the necessary reset.Signed-off-by: Alexander Duyck
Signed-off-by: Don Skidmore
Signed-off-by: David S. Miller -
Currently the media type detection for CX4 adapters lumps them into a
type of fiber. This causes some strange fallout when firmware verification
is done on the NIC, and certain fiber NIC rules get enforced incorrectly.This patch introduces a new media type for CX4, and puts both 82598 and
82599 CX4 adapters into this bucket.Signed-off-by: Peter P Waskiewicz Jr
Signed-off-by: Jeff Kirsher
Signed-off-by: Don Skidmore
Signed-off-by: David S. Miller -
This patch adds support for CX4 adapters based on 82599.
Signed-off-by: Peter P Waskiewicz Jr
Signed-off-by: Jeff Kirsher
Signed-off-by: Don Skidmore
Signed-off-by: David S. Miller -
The packet split feature was recently moved out of the adapter-wide flags
feature field and into a per-Rx ring feature field. In the process, packet
split isn't properly disabled in the Rx ring if the adapter has it globally
disabled, followed by a device reset.This won't impact the driver today, since it's always in packet split mode.
However, this will prevent any pitfalls if someone disables packet split on
the adapter in the future and doesn't disable it in each ring.Signed-off-by: Peter P Waskiewicz Jr
Signed-off-by: Jeff Kirsher
Signed-off-by: Don Skidmore
Signed-off-by: David S. Miller -
From: Rémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont
Signed-off-by: David S. Miller -
Signed-off-by: Alexey Dobriyan
Signed-off-by: David S. Miller -
Now that all Blackfin boards are using the board resources, we don't need
to keep the arch/board specific crap in the driver header.Signed-off-by: Michael Hennerich
Signed-off-by: Mike Frysinger
Signed-off-by: David S. Miller -
* 'osync_cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
fsync: wait for data writeout completion before calling ->fsync
vfs: Remove generic_osync_inode() and sync_page_range{_nolock}()
fat: Opencode sync_page_range_nolock()
pohmelfs: Use new syncing helper
xfs: Convert sync_page_range() to simple filemap_write_and_wait_range()
ocfs2: Update syncing after splicing to match generic version
ntfs: Use new syncing helpers and update comments
ext4: Remove syncing logic from ext4_file_write
ext3: Remove syncing logic from ext3_file_write
ext2: Update comment about generic_osync_inode
vfs: Introduce new helpers for syncing after writing to O_SYNC file or IS_SYNC inode
vfs: Rename generic_file_aio_write_nolock
ocfs2: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
pohmelfs: Use __generic_file_aio_write instead of generic_file_aio_write_nolock
vfs: Remove syncing from generic_file_direct_write() and generic_file_buffered_write()
vfs: Export __generic_file_aio_write() and add some comments
vfs: Introduce filemap_fdatawait_range -
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1623 commits)
netxen: update copyright
netxen: fix tx timeout recovery
netxen: fix file firmware leak
netxen: improve pci memory access
netxen: change firmware write size
tg3: Fix return ring size breakage
netxen: build fix for INET=n
cdc-phonet: autoconfigure Phonet address
Phonet: back-end for autoconfigured addresses
Phonet: fix netlink address dump error handling
ipv6: Add IFA_F_DADFAILED flag
net: Add DEVTYPE support for Ethernet based devices
mv643xx_eth.c: remove unused txq_set_wrr()
ucc_geth: Fix hangs after switching from full to half duplex
ucc_geth: Rearrange some code to avoid forward declarations
phy/marvell: Make non-aneg speed/duplex forcing work for 88E1111 PHYs
drivers/net/phy: introduce missing kfree
drivers/net/wan: introduce missing kfree
net: force bridge module(s) to be GPL
Subject: [PATCH] appletalk: Fix skb leak when ipddp interface is not loaded
...Fixed up trivial conflicts:
- arch/x86/include/asm/socket.h
converted to in the x86 tree. The generic
header has the same new #define's, so that works out fine.- drivers/net/tun.c
fix conflict between 89f56d1e9 ("tun: reuse struct sock fields") that
switched over to using 'tun->socket.sk' instead of the redundantly
available (and thus removed) 'tun->sk', and 2b980dbd ("lsm: Add hooks
to the TUN driver") which added a new 'tun->sk' use.Noted in 'next' by Stephen Rothwell.
-
* 'x86-xen-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: split __phys_addr out into separate file
xen: use stronger barrier after unlocking lock
xen: only enable interrupts while actually blocking for spinlock
xen: make -fstack-protector work under Xen
14 Sep, 2009
4 commits
-
Use new generic_write_sync() helper instead of sync_page_range().
Acked-by: Evgeniy Polyakov
Signed-off-by: Jan Kara -
generic_file_aio_write_nolock() is now used only by block devices and raw
character device. Filesystems should use __generic_file_aio_write() in case
generic_file_aio_write() doesn't suit them. So rename the function to
blkdev_aio_write() and move it to fs/blockdev.c.Signed-off-by: Christoph Hellwig
Signed-off-by: Jan Kara -
Use new helper __generic_file_aio_write(). Since the fs takes care of syncing
by itself afterwards, there are no more changes needed.CC: Evgeniy Polyakov
Signed-off-by: Jan Kara -
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/i386: Put aligned stack-canary in percpu shared_aligned section
x86/i386: Make sure stack-protector segment base is cache aligned
x86: Detect stack protector for i386 builds on x86_64
x86: allow "=rm" in native_save_fl()
x86: properly annotate alternatives.c
x86: Introduce GDT_ENTRY_INIT(), initialize bad_bios_desc statically
x86, 32-bit: Use generic sys_pipe()
x86: Introduce GDT_ENTRY_INIT(), fix APM
x86: Introduce GDT_ENTRY_INIT()
x86: Introduce set_desc_base() and set_desc_limit()
x86: Remove unused patch_espfix_desc()
x86: Use get_desc_base()
12 Sep, 2009
22 commits
-
o Add QLogic copyright, add linux-driver@qlogic.com to
MAINTAINERS.
o Delete old contact information.Signed-off-by: Dhananjay Phadke
Signed-off-by: David S. Miller -
Redesign tx timeout handling in line with new firmware
reset design that co-ordinates with other PCI function
drivers.o For NX3031, first try to reset PCI function's own
context before requesting firmware reset.o For NX2031, since firmware heartbit is not supported
directly request firmware reset.Signed-off-by: Amit Kumar Salecha
Signed-off-by: Dhananjay Phadke
Signed-off-by: David S. Miller -
Release file firmware when no firmware reset is required.
Signed-off-by: Dhananjay Phadke
Signed-off-by: David S. Miller -
o Access on card memory through memory controller (agent)
rather than moving small pci window around. Clean up the
code for moving windows around.o Restrict memory accesss to 64 bit, currently only firmware
download uses this.Signed-off-by: Dhananjay Phadke
Signed-off-by: David S. Miller -
Use 8 byte strides for firmware download into card
memory since oncard memory controller needs 8 byte
(64 bit) accesses. This avoids unnecessary rmw cycles.Signed-off-by: Amit Kumar Salecha
Signed-off-by: Dhananjay Phadke
Signed-off-by: David S. Miller -
Commit f6eb9b1fc1411d22c073f5264e5630a541d0f7df, "tg3: Add 5717 asic
rev" changed how the rx return ring size operations are done. It
effectively inverts the sense of the previous test, but it failed to
also invert the resulting sizes. This patch corrects that error.Signed-off-by: Matt Carlson
Signed-off-by: David S. Miller -
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (25 commits)
pata_rz1000: use printk_once
ahci: kill @force_restart and refine CLO for ahci_kick_engine()
pata_cs5535: add pci id for AMD based CS5535 controllers
ahci: Add AMD SB900 SATA/IDE controller device IDs
drivers/ata: use resource_size
sata_fsl: Defer non-ncq commands when ncq commands active
libata: add SATA PMP revision information for spec 1.2
libata: fix off-by-one error in ata_tf_read_block()
ahci: Gigabyte GA-MA69VM-S2 can't do 64bit DMA
ahci: make ahci_asus_m2a_vm_32bit_only() quirk more generic
dmi: extend dmi_get_year() to dmi_get_date()
dmi: fix date handling in dmi_get_year()
libata: unbreak TPM filtering by reorganizing ata_scsi_pass_thru()
sata_sis: convert to slave_link
sata_sil24: always set protocol override for non-ATAPI data commands
libata: Export AHCI capabilities
libata: Delegate nonrot flag setting to SCSI
[libata] Add pata_rdc driver for RDC ATA devices
drivers/ata: Remove unnecessary semicolons
libata: remove spindown skipping and warning
... -
When CONFIG_INET is disabled, netxen has a build failure:
netxen_nic_main.c:(.text+0x118fd1): undefined reference to `netxen_config_indev_addr'
so make that function just an empty stub when CONFIG_INET=n.
(not "inline" since that conflicts with other declarations of it)Signed-off-by: Randy Dunlap
Acked-by: Dhananjay Phadke
Signed-off-by: David S. Miller -
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (55 commits)
arch/x86/oprofile/op_model_amd.c: fix op_amd_handle_ibs() return type
Revert "x86: oprofile/op_model_amd.c set return values for op_amd_handle_ibs()"
x86/oprofile: Small coding style fixes
x86/oprofile: Add counter reservation check for virtual counters
x86/oprofile: Implement op_x86_virt_to_phys()
oprofile: Adding switch counter to oprofile statistic variables
x86/oprofile: Implement mux_clone()
x86/oprofile: Enable multiplexing only if the model supports it
x86/oprofile: Add function has_mux() to check multiplexing support
x86/oprofile: Modify initialization of num_virt_counters
x86/oprofile: Remove unused num_virt_controls from struct op_x86_model_spec
x86/oprofile: Remove const qualifier from struct op_x86_model_spec
x86/oprofile: Moving nmi_cpu_switch() in nmi_int.c
x86/oprofile: Moving nmi_cpu_save/restore_mpx_registers() in nmi_int.c
x86/oprofile: Moving nmi_setup_cpu_mux() in nmi_int.c
x86/oprofile: Implement multiplexing setup/shutdown functions
oprofile: Grouping multiplexing code in op_model_amd.c
oprofile: Introduce op_x86_phys_to_virt()
oprofile: Grouping multiplexing code in oprof.c
oprofile: Remove oprofile_multiplexing_init()
... -
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
pci/intr_remapping: Allocate irq_iommu on node
irq: Add irq_node() primitive
irq: Make sure irq_desc for legacy irq get correct node setting
genirq: Add prototype for handle_nested_irq()
irq: Remove superfluous NULL pointer check in check_irq_resend()
irq: Clean up by removing irqfixup MODULE_PARM_DESC()
genirq: Fix comment describing suspend_device_irqs()
genirq: Remove obsolete defines and typedefs -
…/git/tip/linux-2.6-tip
* 'core-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
debug lockups: Improve lockup detection, fix generic arch fallback
debug lockups: Improve lockup detection -
Signed-off-by: Rémi Denis-Courmont
Signed-off-by: David S. Miller -
The Ethernet framing is used for a lot of devices these days. Most
prominent are WiFi and WiMAX based devices. However for userspace
application it is important to classify these devices correctly and
not only see them as Ethernet devices. The daemons like HAL, DeviceKit
or even NetworkManager with udev support tries to do the classification
in userspace with a lot trickery and extra system calls. This is not
good and actually reaches its limitations. Especially since the kernel
does know the type of the Ethernet device it is pretty stupid.To solve this problem the underlying device type needs to be set and
then the value will be exported as DEVTYPE via uevents and available
within udev.# cat /sys/class/net/wlan0/uevent
DEVTYPE=wlan
INTERFACE=wlan0
IFINDEX=5This is similar to subsystems like USB and SCSI that distinguish
between hosts, devices, disks, partitions etc.The new SET_NETDEV_DEVTYPE() is a convenience helper to set the actual
device type. All device types are free form, but for convenience the
same strings as used with RFKILL are choosen.Signed-off-by: Marcel Holtmann
Signed-off-by: David S. Miller -
The txq_set_wrr() function in drivers/net/mv643xx_eth.c is
unused, not even referenced under #if 0 or something like that,
which results in a compile-time warning:drivers/net/mv643xx_eth.c:1070: warning: 'txq_set_wrr' defined but not used
Fix: remove it.
Signed-off-by: Mikael Pettersson
Signed-off-by: David S. Miller -
MPC8360 QE UCC ethernet controllers hang when changing link duplex
under a load (a bit of NFS activity is enough).PHY: mdio@e0102120:00 - Link is Up - 1000/Full
sh-3.00# ethtool -s eth0 speed 100 duplex half autoneg off
PHY: mdio@e0102120:00 - Link is Down
PHY: mdio@e0102120:00 - Link is Up - 100/Half
NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
------------[ cut here ]------------
Badness at c01fcbd0 [verbose debug info unavailable]
NIP: c01fcbd0 LR: c01fcbd0 CTR: c0194e44
...The cure is to disable the controller before changing speed/duplex
and enable it afterwards.Though, disabling the controller might take quite a while, so we
better not grab any spinlocks in adjust_link(). Instead, we quiesce
the driver's activity, and only then disable the controller.Signed-off-by: Anton Vorontsov
Signed-off-by: David S. Miller -
We'll need ugeth_disable() and ugeth_enable() calls earlier in the
file, so rearrange some code to avoid forward declarations.The patch doesn't contain any functional changes.
Signed-off-by: Anton Vorontsov
Acked-by: Timur Tabi
Signed-off-by: David S. Miller -
According to specs, when auto-negotiation is disabled, Marvell PHYs need
a software reset after changing speed/duplex forcing bits. Otherwise,
the modified bits have no effect.Signed-off-by: Anton Vorontsov
Signed-off-by: David S. Miller -
Error handling code following a kzalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)//
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
}
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|\|ptr\);
|
return@p2 ...;
)@script:python@
p1 << r.p1;
p2 << r.p2;
@@print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
//Signed-off-by: Julia Lawall
Signed-off-by: David S. Miller -
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)//
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
}
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|\|ptr\);
|
return@p2 ...;
)@script:python@
p1 << r.p1;
p2 << r.p2;
@@print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
//Signed-off-by: Julia Lawall
Signed-off-by: David S. Miller -
And also do a better job of returning proper NET_{RX,XMIT}_ values.
Based on a patch and suggestions by Mark Smith.
This fixes CVE-2009-2903
Reported-by: Mark Smith
Signed-off-by: Arnaldo Carvalho de Melo
Signed-off-by: David S. Miller -
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (102 commits)
crypto: sha-s390 - Fix warnings in import function
crypto: vmac - New hash algorithm for intel_txt support
crypto: api - Do not displace newly registered algorithms
crypto: ansi_cprng - Fix module initialization
crypto: xcbc - Fix alignment calculation of xcbc_tfm_ctx
crypto: fips - Depend on ansi_cprng
crypto: blkcipher - Do not use eseqiv on stream ciphers
crypto: ctr - Use chainiv on raw counter mode
Revert crypto: fips - Select CPRNG
crypto: rng - Fix typo
crypto: talitos - add support for 36 bit addressing
crypto: talitos - align locks on cache lines
crypto: talitos - simplify hmac data size calculation
crypto: mv_cesa - Add support for Orion5X crypto engine
crypto: cryptd - Add support to access underlaying shash
crypto: gcm - Use GHASH digest algorithm
crypto: ghash - Add GHASH digest algorithm for GCM
crypto: authenc - Convert to ahash
crypto: api - Fix aligned ctx helper
crypto: hmac - Prehash ipad/opad
... -
* 'writeback' of git://git.kernel.dk/linux-2.6-block:
writeback: check for registered bdi in flusher add and inode dirty
writeback: add name to backing_dev_info
writeback: add some debug inode list counters to bdi stats
writeback: get rid of pdflush completely
writeback: switch to per-bdi threads for flushing data
writeback: move dirty inodes from super_block to backing_dev_info
writeback: get rid of generic_sync_sb_inodes() export
