/*
   * NS16550 Serial Port

   * originally from linux source (arch/powerpc/boot/ns16550.h)

   *
   * Cleanup and unification
   * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
   *

   * modified slightly to

   * have addresses as offsets from CONFIG_SYS_ISA_BASE

   * added a few more definitions
   * added prototypes for ns16550.c
   * reduced no of com ports to 2
   * modifications (c) Rob Taylor, Flying Pig Systems. 2000.

   *

   * added support for port on 64-bit bus
   * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems

   */

  /*
   * Note that the following macro magic uses the fact that the compiler
   * will not allocate storage for arrays of size 0
   */

  #include <linux/types.h>

  #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)

  #error "Please define NS16550 registers size."

  #elif defined(CONFIG_SYS_NS16550_MEM32)
  #define UART_REG(x) u32 x

  #elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
  #define UART_REG(x)						   \
  	unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
  	unsigned char x;
  #elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
  #define UART_REG(x)							\
  	unsigned char x;						\
  	unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];

  #endif

  struct NS16550 {
  	UART_REG(rbr);		/* 0 */
  	UART_REG(ier);		/* 1 */
  	UART_REG(fcr);		/* 2 */
  	UART_REG(lcr);		/* 3 */
  	UART_REG(mcr);		/* 4 */
  	UART_REG(lsr);		/* 5 */
  	UART_REG(msr);		/* 6 */
  	UART_REG(spr);		/* 7 */

  #ifdef CONFIG_SOC_DA8XX
  	UART_REG(reg8);		/* 8 */
  	UART_REG(reg9);		/* 9 */
  	UART_REG(revid1);	/* A */
  	UART_REG(revid2);	/* B */
  	UART_REG(pwr_mgmt);	/* C */
  	UART_REG(mdr1);		/* D */
  #else

  	UART_REG(mdr1);		/* 8 */
  	UART_REG(reg9);		/* 9 */
  	UART_REG(regA);		/* A */
  	UART_REG(regB);		/* B */
  	UART_REG(regC);		/* C */
  	UART_REG(regD);		/* D */
  	UART_REG(regE);		/* E */
  	UART_REG(uasr);		/* F */
  	UART_REG(scr);		/* 10*/
  	UART_REG(ssr);		/* 11*/
  	UART_REG(reg12);	/* 12*/
  	UART_REG(osc_12m_sel);	/* 13*/

  #endif

  };

  #define thr rbr
  #define iir fcr
  #define dll rbr
  #define dlm ier

  typedef struct NS16550 *NS16550_t;

  /*
   * These are the definitions for the FIFO Control Register
   */

  #define UART_FCR_FIFO_EN	0x01 /* Fifo enable */

  #define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
  #define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
  #define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
  #define UART_FCR_TRIGGER_MASK	0xC0 /* Mask for the FIFO trigger range */
  #define UART_FCR_TRIGGER_1	0x00 /* Mask for trigger set at 1 */
  #define UART_FCR_TRIGGER_4	0x40 /* Mask for trigger set at 4 */
  #define UART_FCR_TRIGGER_8	0x80 /* Mask for trigger set at 8 */
  #define UART_FCR_TRIGGER_14	0xC0 /* Mask for trigger set at 14 */
  
  #define UART_FCR_RXSR		0x02 /* Receiver soft reset */
  #define UART_FCR_TXSR		0x04 /* Transmitter soft reset */
  
  /*
   * These are the definitions for the Modem Control Register
   */
  #define UART_MCR_DTR	0x01		/* DTR   */
  #define UART_MCR_RTS	0x02		/* RTS   */
  #define UART_MCR_OUT1	0x04		/* Out 1 */
  #define UART_MCR_OUT2	0x08		/* Out 2 */
  #define UART_MCR_LOOP	0x10		/* Enable loopback test mode */
  
  #define UART_MCR_DMA_EN	0x04
  #define UART_MCR_TX_DFR	0x08
  
  /*
   * These are the definitions for the Line Control Register
   *
   * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
   * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
   */
  #define UART_LCR_WLS_MSK 0x03		/* character length select mask */
  #define UART_LCR_WLS_5	0x00		/* 5 bit character length */
  #define UART_LCR_WLS_6	0x01		/* 6 bit character length */
  #define UART_LCR_WLS_7	0x02		/* 7 bit character length */
  #define UART_LCR_WLS_8	0x03		/* 8 bit character length */

  #define UART_LCR_STB	0x04		/* # stop Bits, off=1, on=1.5 or 2) */

  #define UART_LCR_PEN	0x08		/* Parity eneble */
  #define UART_LCR_EPS	0x10		/* Even Parity Select */
  #define UART_LCR_STKP	0x20		/* Stick Parity */
  #define UART_LCR_SBRK	0x40		/* Set Break */
  #define UART_LCR_BKSE	0x80		/* Bank select enable */
  #define UART_LCR_DLAB	0x80		/* Divisor latch access bit */
  
  /*
   * These are the definitions for the Line Status Register
   */
  #define UART_LSR_DR	0x01		/* Data ready */
  #define UART_LSR_OE	0x02		/* Overrun */
  #define UART_LSR_PE	0x04		/* Parity error */
  #define UART_LSR_FE	0x08		/* Framing error */
  #define UART_LSR_BI	0x10		/* Break */
  #define UART_LSR_THRE	0x20		/* Xmit holding register empty */
  #define UART_LSR_TEMT	0x40		/* Xmitter empty */
  #define UART_LSR_ERR	0x80		/* Error */
  
  #define UART_MSR_DCD	0x80		/* Data Carrier Detect */
  #define UART_MSR_RI	0x40		/* Ring Indicator */
  #define UART_MSR_DSR	0x20		/* Data Set Ready */
  #define UART_MSR_CTS	0x10		/* Clear to Send */
  #define UART_MSR_DDCD	0x08		/* Delta DCD */
  #define UART_MSR_TERI	0x04		/* Trailing edge ring indicator */
  #define UART_MSR_DDSR	0x02		/* Delta DSR */
  #define UART_MSR_DCTS	0x01		/* Delta CTS */
  
  /*
   * These are the definitions for the Interrupt Identification Register
   */
  #define UART_IIR_NO_INT	0x01	/* No interrupts pending */
  #define UART_IIR_ID	0x06	/* Mask for the interrupt ID */
  
  #define UART_IIR_MSI	0x00	/* Modem status interrupt */
  #define UART_IIR_THRI	0x02	/* Transmitter holding register empty */
  #define UART_IIR_RDI	0x04	/* Receiver data interrupt */
  #define UART_IIR_RLSI	0x06	/* Receiver line status interrupt */
  
  /*
   * These are the definitions for the Interrupt Enable Register
   */
  #define UART_IER_MSI	0x08	/* Enable Modem status interrupt */
  #define UART_IER_RLSI	0x04	/* Enable receiver line status interrupt */
  #define UART_IER_THRI	0x02	/* Enable Transmitter holding register int. */
  #define UART_IER_RDI	0x01	/* Enable receiver data interrupt */

  #ifdef CONFIG_OMAP1510

  #define OSC_12M_SEL	0x01	/* selects 6.5 * current clk div */

  #endif

  /* useful defaults for LCR */

  #define UART_LCR_8N1	0x03

  void NS16550_init(NS16550_t com_port, int baud_divisor);
  void NS16550_putc(NS16550_t com_port, char c);
  char NS16550_getc(NS16550_t com_port);
  int NS16550_tstc(NS16550_t com_port);
  void NS16550_reinit(NS16550_t com_port, int baud_divisor);