Blame view
cmd/i2c.c
48.5 KB
81a8824f2 Initial revision |
1 |
/* |
3f4978c71 i2c: common chang... |
2 3 4 5 6 |
* (C) Copyright 2009 * Sergey Kubushyn, himself, ksi@koi8.net * * Changes for unified multibus/multiadapter I2C support. * |
81a8824f2 Initial revision |
7 8 9 |
* (C) Copyright 2001 * Gerald Van Baren, Custom IDEAS, vanbaren@cideas.com. * |
1a4596601 Add GPL-2.0+ SPDX... |
10 |
* SPDX-License-Identifier: GPL-2.0+ |
81a8824f2 Initial revision |
11 12 13 14 15 16 17 18 |
*/ /* * I2C Functions similar to the standard memory functions. * * There are several parameters in many of the commands that bear further * explanations: * |
81a8824f2 Initial revision |
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 |
* {i2c_chip} is the I2C chip address (the first byte sent on the bus). * Each I2C chip on the bus has a unique address. On the I2C data bus, * the address is the upper seven bits and the LSB is the "read/write" * bit. Note that the {i2c_chip} address specified on the command * line is not shifted up: e.g. a typical EEPROM memory chip may have * an I2C address of 0x50, but the data put on the bus will be 0xA0 * for write and 0xA1 for read. This "non shifted" address notation * matches at least half of the data sheets :-/. * * {addr} is the address (or offset) within the chip. Small memory * chips have 8 bit addresses. Large memory chips have 16 bit * addresses. Other memory chips have 9, 10, or 11 bit addresses. * Many non-memory chips have multiple registers and {addr} is used * as the register index. Some non-memory chips have only one register * and therefore don't need any {addr} parameter. * * The default {addr} parameter is one byte (.1) which works well for * memories and registers with 8 bits of address space. * * You can specify the length of the {addr} field with the optional .0, * .1, or .2 modifier (similar to the .b, .w, .l modifier). If you are * manipulating a single register device which doesn't use an address * field, use "0.0" for the address and the ".0" length field will * suppress the address in the I2C data stream. This also works for * successive reads using the I2C auto-incrementing memory pointer. * * If you are manipulating a large memory with 2-byte addresses, use * the .2 address modifier, e.g. 210.2 addresses location 528 (decimal). * * Then there are the unfortunate memory chips that spill the most * significant 1, 2, or 3 bits of address into the chip address byte. * This effectively makes one chip (logically) look like 2, 4, or * 8 chips. This is handled (awkwardly) by #defining |
6d0f6bcf3 rename CFG_ macro... |
52 |
* CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW and using the .1 modifier on the |
81a8824f2 Initial revision |
53 54 55 |
* {addr} field (since .1 is the default, it doesn't actually have to * be specified). Examples: given a memory chip at I2C chip address * 0x50, the following would happen... |
0f89c54be i2c: Update refer... |
56 |
* i2c md 50 0 10 display 16 bytes starting at 0x000 |
81a8824f2 Initial revision |
57 |
* On the bus: <S> A0 00 <E> <S> A1 <rd> ... <rd> |
0f89c54be i2c: Update refer... |
58 |
* i2c md 50 100 10 display 16 bytes starting at 0x100 |
81a8824f2 Initial revision |
59 |
* On the bus: <S> A2 00 <E> <S> A3 <rd> ... <rd> |
0f89c54be i2c: Update refer... |
60 |
* i2c md 50 210 10 display 16 bytes starting at 0x210 |
81a8824f2 Initial revision |
61 62 63 64 65 66 67 68 |
* On the bus: <S> A4 10 <E> <S> A5 <rd> ... <rd> * This is awfully ugly. It would be nice if someone would think up * a better way of handling this. * * Adapted from cmd_mem.c which is copyright Wolfgang Denk (wd@denx.de). */ #include <common.h> |
0098e179e Move bootretry co... |
69 |
#include <bootretry.h> |
18d66533a move CLI prototyp... |
70 |
#include <cli.h> |
81a8824f2 Initial revision |
71 |
#include <command.h> |
24b852a7a Move console defi... |
72 |
#include <console.h> |
63656b762 dm: i2c: Implemen... |
73 |
#include <dm.h> |
735987c5a edid: Add I2C com... |
74 |
#include <edid.h> |
67b23a322 I2C: adding new "... |
75 |
#include <environment.h> |
63656b762 dm: i2c: Implemen... |
76 |
#include <errno.h> |
81a8824f2 Initial revision |
77 |
#include <i2c.h> |
67b23a322 I2C: adding new "... |
78 |
#include <malloc.h> |
81a8824f2 Initial revision |
79 |
#include <asm/byteorder.h> |
2515d8437 i2c: Use __weak i... |
80 |
#include <linux/compiler.h> |
81a8824f2 Initial revision |
81 |
|
3f4978c71 i2c: common chang... |
82 |
DECLARE_GLOBAL_DATA_PTR; |
81a8824f2 Initial revision |
83 84 85 |
/* Display values from last command. * Memory modify remembered values are different from display memory. */ |
5468461d1 cmd_i2c: change v... |
86 |
static uint i2c_dp_last_chip; |
81a8824f2 Initial revision |
87 88 89 |
static uint i2c_dp_last_addr; static uint i2c_dp_last_alen; static uint i2c_dp_last_length = 0x10; |
5468461d1 cmd_i2c: change v... |
90 |
static uint i2c_mm_last_chip; |
81a8824f2 Initial revision |
91 92 |
static uint i2c_mm_last_addr; static uint i2c_mm_last_alen; |
bb99ad6d8 Add support for m... |
93 94 95 96 |
/* If only one I2C bus is present, the list of devices to ignore when * the probe command is issued is represented by a 1D array of addresses. * When multiple buses are present, the list is an array of bus-address * pairs. The following macros take care of this */ |
6d0f6bcf3 rename CFG_ macro... |
97 |
#if defined(CONFIG_SYS_I2C_NOPROBES) |
9a2accb44 i2c, multibus: ge... |
98 |
#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS) |
bb99ad6d8 Add support for m... |
99 100 101 102 |
static struct { uchar bus; uchar addr; |
6d0f6bcf3 rename CFG_ macro... |
103 |
} i2c_no_probes[] = CONFIG_SYS_I2C_NOPROBES; |
bb99ad6d8 Add support for m... |
104 105 106 107 108 |
#define GET_BUS_NUM i2c_get_bus_num() #define COMPARE_BUS(b,i) (i2c_no_probes[(i)].bus == (b)) #define COMPARE_ADDR(a,i) (i2c_no_probes[(i)].addr == (a)) #define NO_PROBE_ADDR(i) i2c_no_probes[(i)].addr #else /* single bus */ |
6d0f6bcf3 rename CFG_ macro... |
109 |
static uchar i2c_no_probes[] = CONFIG_SYS_I2C_NOPROBES; |
bb99ad6d8 Add support for m... |
110 111 112 113 |
#define GET_BUS_NUM 0 #define COMPARE_BUS(b,i) ((b) == 0) /* Make compiler happy */ #define COMPARE_ADDR(a,i) (i2c_no_probes[(i)] == (a)) #define NO_PROBE_ADDR(i) i2c_no_probes[(i)] |
3f4978c71 i2c: common chang... |
114 |
#endif /* defined(CONFIG_SYS_I2C) */ |
67b23a322 I2C: adding new "... |
115 |
#endif |
a266fe955 cmd_i2c: moved a ... |
116 |
#define DISP_LINE_LEN 16 |
63656b762 dm: i2c: Implemen... |
117 118 119 120 121 122 123 124 125 126 127 128 129 |
/* * Default for driver model is to use the chip's existing address length. * For legacy code, this is not stored, so we need to use a suitable * default. */ #ifdef CONFIG_DM_I2C #define DEFAULT_ADDR_LEN (-1) #else #define DEFAULT_ADDR_LEN 1 #endif #ifdef CONFIG_DM_I2C static struct udevice *i2c_cur_bus; |
f9a4c2da7 dm: i2c: Rename d... |
130 |
static int cmd_i2c_set_bus_num(unsigned int busnum) |
63656b762 dm: i2c: Implemen... |
131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 |
{ struct udevice *bus; int ret; ret = uclass_get_device_by_seq(UCLASS_I2C, busnum, &bus); if (ret) { debug("%s: No bus %d ", __func__, busnum); return ret; } i2c_cur_bus = bus; return 0; } static int i2c_get_cur_bus(struct udevice **busp) { |
e46f8a330 i2c: Set default ... |
148 149 150 151 152 153 154 155 156 157 |
#ifdef CONFIG_I2C_SET_DEFAULT_BUS_NUM if (!i2c_cur_bus) { if (cmd_i2c_set_bus_num(CONFIG_I2C_DEFAULT_BUS_NUMBER)) { printf("Default I2C bus %d not found ", CONFIG_I2C_DEFAULT_BUS_NUMBER); return -ENODEV; } } #endif |
63656b762 dm: i2c: Implemen... |
158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 |
if (!i2c_cur_bus) { puts("No I2C bus selected "); return -ENODEV; } *busp = i2c_cur_bus; return 0; } static int i2c_get_cur_bus_chip(uint chip_addr, struct udevice **devp) { struct udevice *bus; int ret; ret = i2c_get_cur_bus(&bus); if (ret) return ret; |
25ab4b030 dm: i2c: Provide ... |
176 |
return i2c_get_chip(bus, chip_addr, 1, devp); |
63656b762 dm: i2c: Implemen... |
177 178 179 |
} #endif |
06afa388b i2c: kerneldoc: A... |
180 181 182 183 |
/** * i2c_init_board() - Board-specific I2C bus init * * This function is the default no-op implementation of I2C bus |
62a3b7dd0 Various, unrelate... |
184 |
* initialization. This function can be overridden by board-specific |
06afa388b i2c: kerneldoc: A... |
185 186 |
* implementation if needed. */ |
2515d8437 i2c: Use __weak i... |
187 188 |
__weak void i2c_init_board(void) |
c649dda53 i2c: add i2c debl... |
189 |
{ |
c649dda53 i2c: add i2c debl... |
190 |
} |
c649dda53 i2c: add i2c debl... |
191 |
|
655b34a78 i2c: Create commo... |
192 |
/* TODO: Implement architecture-specific get/set functions */ |
06afa388b i2c: kerneldoc: A... |
193 194 195 196 197 198 199 200 201 202 203 204 205 |
/** * i2c_get_bus_speed() - Return I2C bus speed * * This function is the default implementation of function for retrieveing * the current I2C bus speed in Hz. * * A driver implementing runtime switching of I2C bus speed must override * this function to report the speed correctly. Simple or legacy drivers * can use this fallback. * * Returns I2C bus speed in Hz. */ |
63656b762 dm: i2c: Implemen... |
206 |
#if !defined(CONFIG_SYS_I2C) && !defined(CONFIG_DM_I2C) |
3f4978c71 i2c: common chang... |
207 208 209 210 |
/* * TODO: Implement architecture-specific get/set functions * Should go away, if we switched completely to new multibus support */ |
2515d8437 i2c: Use __weak i... |
211 212 |
__weak unsigned int i2c_get_bus_speed(void) |
655b34a78 i2c: Create commo... |
213 214 215 |
{ return CONFIG_SYS_I2C_SPEED; } |
655b34a78 i2c: Create commo... |
216 |
|
06afa388b i2c: kerneldoc: A... |
217 218 219 220 221 222 223 224 225 226 227 228 229 |
/** * i2c_set_bus_speed() - Configure I2C bus speed * @speed: Newly set speed of the I2C bus in Hz * * This function is the default implementation of function for setting * the I2C bus speed in Hz. * * A driver implementing runtime switching of I2C bus speed must override * this function to report the speed correctly. Simple or legacy drivers * can use this fallback. * * Returns zero on success, negative value on error. */ |
2515d8437 i2c: Use __weak i... |
230 231 |
__weak int i2c_set_bus_speed(unsigned int speed) |
655b34a78 i2c: Create commo... |
232 233 234 235 236 237 |
{ if (speed != CONFIG_SYS_I2C_SPEED) return -1; return 0; } |
3f4978c71 i2c: common chang... |
238 |
#endif |
655b34a78 i2c: Create commo... |
239 |
|
06afa388b i2c: kerneldoc: A... |
240 241 242 243 |
/** * get_alen() - Small parser helper function to get address length * * Returns the address length. |
2c0dc9902 cmd_i2c: introduc... |
244 |
*/ |
63656b762 dm: i2c: Implemen... |
245 |
static uint get_alen(char *arg, int default_len) |
2c0dc9902 cmd_i2c: introduc... |
246 247 248 |
{ int j; int alen; |
63656b762 dm: i2c: Implemen... |
249 |
alen = default_len; |
2c0dc9902 cmd_i2c: introduc... |
250 251 252 |
for (j = 0; j < 8; j++) { if (arg[j] == '.') { alen = arg[j+1] - '0'; |
2c0dc9902 cmd_i2c: introduc... |
253 254 255 256 257 258 |
break; } else if (arg[j] == '\0') break; } return alen; } |
c1a6f371a dm: i2c: Move err... |
259 260 261 262 263 264 265 266 267 268 269 270 271 |
enum i2c_err_op { I2C_ERR_READ, I2C_ERR_WRITE, }; static int i2c_report_err(int ret, enum i2c_err_op op) { printf("Error %s the chip: %d ", op == I2C_ERR_READ ? "reading" : "writing", ret); return CMD_RET_FAILURE; } |
06afa388b i2c: kerneldoc: A... |
272 273 274 275 276 277 278 279 280 281 |
/** * do_i2c_read() - Handle the "i2c read" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. * |
652e53546 cmd_i2c.c: added ... |
282 283 284 |
* Syntax: * i2c read {i2c_chip} {devaddr}{.0, .1, .2} {len} {memaddr} */ |
54841ab50 Make sure that ar... |
285 |
static int do_i2c_read ( cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
652e53546 cmd_i2c.c: added ... |
286 |
{ |
5468461d1 cmd_i2c: change v... |
287 |
uint chip; |
63656b762 dm: i2c: Implemen... |
288 289 |
uint devaddr, length; int alen; |
652e53546 cmd_i2c.c: added ... |
290 |
u_char *memaddr; |
63656b762 dm: i2c: Implemen... |
291 292 293 294 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
652e53546 cmd_i2c.c: added ... |
295 |
|
47e26b1bf cmd_usage(): simp... |
296 |
if (argc != 5) |
4c12eeb8b Convert cmd_usage... |
297 |
return CMD_RET_USAGE; |
652e53546 cmd_i2c.c: added ... |
298 299 300 301 302 303 304 305 306 307 308 |
/* * I2C chip address */ chip = simple_strtoul(argv[1], NULL, 16); /* * I2C data address within the chip. This can be 1 or * 2 bytes long. Some day it might be 3 bytes long :-). */ devaddr = simple_strtoul(argv[2], NULL, 16); |
63656b762 dm: i2c: Implemen... |
309 |
alen = get_alen(argv[2], DEFAULT_ADDR_LEN); |
7a92e53cd CMD_I2C: make ale... |
310 |
if (alen > 3) |
4c12eeb8b Convert cmd_usage... |
311 |
return CMD_RET_USAGE; |
652e53546 cmd_i2c.c: added ... |
312 313 314 315 316 317 318 319 320 321 |
/* * Length is the number of objects, not number of bytes. */ length = simple_strtoul(argv[3], NULL, 16); /* * memaddr is the address where to store things in memory */ memaddr = (u_char *)simple_strtoul(argv[4], NULL, 16); |
63656b762 dm: i2c: Implemen... |
322 323 324 325 326 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (!ret) |
f9a4c2da7 dm: i2c: Rename d... |
327 |
ret = dm_i2c_read(dev, devaddr, memaddr, length); |
63656b762 dm: i2c: Implemen... |
328 329 330 331 332 |
#else ret = i2c_read(chip, devaddr, alen, memaddr, length); #endif if (ret) return i2c_report_err(ret, I2C_ERR_READ); |
652e53546 cmd_i2c.c: added ... |
333 334 |
return 0; } |
ff5d2dce1 common/i2c: Add i... |
335 336 |
static int do_i2c_write(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { |
5468461d1 cmd_i2c: change v... |
337 |
uint chip; |
63656b762 dm: i2c: Implemen... |
338 339 |
uint devaddr, length; int alen; |
ff5d2dce1 common/i2c: Add i... |
340 |
u_char *memaddr; |
63656b762 dm: i2c: Implemen... |
341 342 343 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; |
ed16f1468 cmd_i2c: Provide ... |
344 |
struct dm_i2c_chip *i2c_chip; |
63656b762 dm: i2c: Implemen... |
345 |
#endif |
ff5d2dce1 common/i2c: Add i... |
346 |
|
ed16f1468 cmd_i2c: Provide ... |
347 |
if ((argc < 5) || (argc > 6)) |
ff5d2dce1 common/i2c: Add i... |
348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 |
return cmd_usage(cmdtp); /* * memaddr is the address where to store things in memory */ memaddr = (u_char *)simple_strtoul(argv[1], NULL, 16); /* * I2C chip address */ chip = simple_strtoul(argv[2], NULL, 16); /* * I2C data address within the chip. This can be 1 or * 2 bytes long. Some day it might be 3 bytes long :-). */ devaddr = simple_strtoul(argv[3], NULL, 16); |
63656b762 dm: i2c: Implemen... |
365 |
alen = get_alen(argv[3], DEFAULT_ADDR_LEN); |
ff5d2dce1 common/i2c: Add i... |
366 367 368 369 |
if (alen > 3) return cmd_usage(cmdtp); /* |
ed16f1468 cmd_i2c: Provide ... |
370 |
* Length is the number of bytes. |
ff5d2dce1 common/i2c: Add i... |
371 372 |
*/ length = simple_strtoul(argv[4], NULL, 16); |
63656b762 dm: i2c: Implemen... |
373 374 375 376 377 378 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (ret) return i2c_report_err(ret, I2C_ERR_WRITE); |
ed16f1468 cmd_i2c: Provide ... |
379 380 381 |
i2c_chip = dev_get_parent_platdata(dev); if (!i2c_chip) return i2c_report_err(ret, I2C_ERR_WRITE); |
63656b762 dm: i2c: Implemen... |
382 |
#endif |
ed16f1468 cmd_i2c: Provide ... |
383 384 385 386 387 388 389 |
if (argc == 6 && !strcmp(argv[5], "-s")) { /* * Write all bytes in a single I2C transaction. If the target * device is an EEPROM, it is your responsibility to not cross * a page boundary. No write delay upon completion, take this * into account if linking commands. */ |
63656b762 dm: i2c: Implemen... |
390 |
#ifdef CONFIG_DM_I2C |
ed16f1468 cmd_i2c: Provide ... |
391 392 |
i2c_chip->flags &= ~DM_I2C_CHIP_WR_ADDRESS; ret = dm_i2c_write(dev, devaddr, memaddr, length); |
63656b762 dm: i2c: Implemen... |
393 |
#else |
ed16f1468 cmd_i2c: Provide ... |
394 |
ret = i2c_write(chip, devaddr, alen, memaddr, length); |
63656b762 dm: i2c: Implemen... |
395 396 397 |
#endif if (ret) return i2c_report_err(ret, I2C_ERR_WRITE); |
ed16f1468 cmd_i2c: Provide ... |
398 399 400 401 402 403 404 405 406 407 408 409 410 411 |
} else { /* * Repeated addressing - perform <length> separate * write transactions of one byte each */ while (length-- > 0) { #ifdef CONFIG_DM_I2C i2c_chip->flags |= DM_I2C_CHIP_WR_ADDRESS; ret = dm_i2c_write(dev, devaddr++, memaddr++, 1); #else ret = i2c_write(chip, devaddr++, alen, memaddr++, 1); #endif if (ret) return i2c_report_err(ret, I2C_ERR_WRITE); |
ff5d2dce1 common/i2c: Add i... |
412 413 414 415 |
/* * No write delay with FRAM devices. */ #if !defined(CONFIG_SYS_I2C_FRAM) |
ed16f1468 cmd_i2c: Provide ... |
416 |
udelay(11000); |
ff5d2dce1 common/i2c: Add i... |
417 |
#endif |
ed16f1468 cmd_i2c: Provide ... |
418 |
} |
ff5d2dce1 common/i2c: Add i... |
419 420 421 |
} return 0; } |
63656b762 dm: i2c: Implemen... |
422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 |
#ifdef CONFIG_DM_I2C static int do_i2c_flags(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) { struct udevice *dev; uint flags; int chip; int ret; if (argc < 2) return CMD_RET_USAGE; chip = simple_strtoul(argv[1], NULL, 16); ret = i2c_get_cur_bus_chip(chip, &dev); if (ret) return i2c_report_err(ret, I2C_ERR_READ); if (argc > 2) { flags = simple_strtoul(argv[2], NULL, 16); ret = i2c_set_chip_flags(dev, flags); } else { ret = i2c_get_chip_flags(dev, &flags); if (!ret) printf("%x ", flags); } if (ret) return i2c_report_err(ret, I2C_ERR_READ); return 0; } |
c10c8e313 dm: i2c: Add a co... |
453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 |
static int do_i2c_olen(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) { struct udevice *dev; uint olen; int chip; int ret; if (argc < 2) return CMD_RET_USAGE; chip = simple_strtoul(argv[1], NULL, 16); ret = i2c_get_cur_bus_chip(chip, &dev); if (ret) return i2c_report_err(ret, I2C_ERR_READ); if (argc > 2) { olen = simple_strtoul(argv[2], NULL, 16); ret = i2c_set_chip_offset_len(dev, olen); } else { ret = i2c_get_chip_offset_len(dev); if (ret >= 0) { printf("%x ", ret); ret = 0; } } if (ret) return i2c_report_err(ret, I2C_ERR_READ); return 0; } |
63656b762 dm: i2c: Implemen... |
485 |
#endif |
06afa388b i2c: kerneldoc: A... |
486 487 488 489 490 491 492 493 494 495 |
/** * do_i2c_md() - Handle the "i2c md" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. * |
4a8cf3382 cmd_i2c: moved mi... |
496 497 498 |
* Syntax: * i2c md {i2c_chip} {addr}{.0, .1, .2} {len} */ |
54841ab50 Make sure that ar... |
499 |
static int do_i2c_md ( cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
500 |
{ |
5468461d1 cmd_i2c: change v... |
501 |
uint chip; |
63656b762 dm: i2c: Implemen... |
502 503 |
uint addr, length; int alen; |
81a8824f2 Initial revision |
504 |
int j, nbytes, linebytes; |
63656b762 dm: i2c: Implemen... |
505 506 507 508 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
81a8824f2 Initial revision |
509 510 511 512 513 514 515 516 |
/* We use the last specified parameters, unless new ones are * entered. */ chip = i2c_dp_last_chip; addr = i2c_dp_last_addr; alen = i2c_dp_last_alen; length = i2c_dp_last_length; |
47e26b1bf cmd_usage(): simp... |
517 |
if (argc < 3) |
4c12eeb8b Convert cmd_usage... |
518 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
519 520 521 522 523 |
if ((flag & CMD_FLAG_REPEAT) == 0) { /* * New command specified. */ |
81a8824f2 Initial revision |
524 525 526 527 528 529 530 531 532 533 534 |
/* * I2C chip address */ chip = simple_strtoul(argv[1], NULL, 16); /* * I2C data address within the chip. This can be 1 or * 2 bytes long. Some day it might be 3 bytes long :-). */ addr = simple_strtoul(argv[2], NULL, 16); |
63656b762 dm: i2c: Implemen... |
535 |
alen = get_alen(argv[2], DEFAULT_ADDR_LEN); |
7a92e53cd CMD_I2C: make ale... |
536 |
if (alen > 3) |
4c12eeb8b Convert cmd_usage... |
537 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
538 539 540 541 542 543 544 545 |
/* * If another parameter, it is the length to display. * Length is the number of objects, not number of bytes. */ if (argc > 3) length = simple_strtoul(argv[3], NULL, 16); } |
63656b762 dm: i2c: Implemen... |
546 547 548 549 550 551 552 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (ret) return i2c_report_err(ret, I2C_ERR_READ); #endif |
81a8824f2 Initial revision |
553 554 555 556 557 558 559 560 561 562 563 564 |
/* * Print the lines. * * We buffer all read data, so we can make sure data is read only * once. */ nbytes = length; do { unsigned char linebuf[DISP_LINE_LEN]; unsigned char *cp; linebytes = (nbytes > DISP_LINE_LEN) ? DISP_LINE_LEN : nbytes; |
63656b762 dm: i2c: Implemen... |
565 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
566 |
ret = dm_i2c_read(dev, addr, linebuf, linebytes); |
63656b762 dm: i2c: Implemen... |
567 568 569 570 |
#else ret = i2c_read(chip, addr, alen, linebuf, linebytes); #endif if (ret) |
9e533cb04 cmd_i2c: quit I2C... |
571 |
return i2c_report_err(ret, I2C_ERR_READ); |
e857a5bdb mpc83xx: Miscella... |
572 |
else { |
81a8824f2 Initial revision |
573 574 575 576 577 578 |
printf("%04x:", addr); cp = linebuf; for (j=0; j<linebytes; j++) { printf(" %02x", *cp++); addr++; } |
4b9206ed5 * Patches by Thom... |
579 |
puts (" "); |
81a8824f2 Initial revision |
580 581 582 |
cp = linebuf; for (j=0; j<linebytes; j++) { if ((*cp < 0x20) || (*cp > 0x7e)) |
4b9206ed5 * Patches by Thom... |
583 |
puts ("."); |
81a8824f2 Initial revision |
584 585 586 587 |
else printf("%c", *cp); cp++; } |
4b9206ed5 * Patches by Thom... |
588 589 |
putc (' '); |
81a8824f2 Initial revision |
590 591 592 593 594 595 596 597 598 599 600 |
} nbytes -= linebytes; } while (nbytes > 0); i2c_dp_last_chip = chip; i2c_dp_last_addr = addr; i2c_dp_last_alen = alen; i2c_dp_last_length = length; return 0; } |
06afa388b i2c: kerneldoc: A... |
601 602 603 604 605 606 607 608 609 |
/** * do_i2c_mw() - Handle the "i2c mw" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. |
81a8824f2 Initial revision |
610 611 |
* * Syntax: |
0f89c54be i2c: Update refer... |
612 |
* i2c mw {i2c_chip} {addr}{.0, .1, .2} {data} [{count}] |
81a8824f2 Initial revision |
613 |
*/ |
54841ab50 Make sure that ar... |
614 |
static int do_i2c_mw ( cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
615 |
{ |
5468461d1 cmd_i2c: change v... |
616 |
uint chip; |
81a8824f2 Initial revision |
617 |
ulong addr; |
63656b762 dm: i2c: Implemen... |
618 |
int alen; |
81a8824f2 Initial revision |
619 620 |
uchar byte; int count; |
63656b762 dm: i2c: Implemen... |
621 622 623 624 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
81a8824f2 Initial revision |
625 |
|
47e26b1bf cmd_usage(): simp... |
626 |
if ((argc < 4) || (argc > 5)) |
4c12eeb8b Convert cmd_usage... |
627 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
628 629 |
/* |
53677ef18 Big white-space c... |
630 631 |
* Chip is always specified. */ |
81a8824f2 Initial revision |
632 633 634 635 636 637 |
chip = simple_strtoul(argv[1], NULL, 16); /* * Address is always specified. */ addr = simple_strtoul(argv[2], NULL, 16); |
63656b762 dm: i2c: Implemen... |
638 |
alen = get_alen(argv[2], DEFAULT_ADDR_LEN); |
7a92e53cd CMD_I2C: make ale... |
639 |
if (alen > 3) |
4c12eeb8b Convert cmd_usage... |
640 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
641 |
|
63656b762 dm: i2c: Implemen... |
642 643 644 645 646 647 648 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (ret) return i2c_report_err(ret, I2C_ERR_WRITE); #endif |
81a8824f2 Initial revision |
649 650 651 652 653 654 655 656 |
/* * Value to write is always specified. */ byte = simple_strtoul(argv[3], NULL, 16); /* * Optional count */ |
e857a5bdb mpc83xx: Miscella... |
657 |
if (argc == 5) |
81a8824f2 Initial revision |
658 |
count = simple_strtoul(argv[4], NULL, 16); |
e857a5bdb mpc83xx: Miscella... |
659 |
else |
81a8824f2 Initial revision |
660 |
count = 1; |
81a8824f2 Initial revision |
661 662 |
while (count-- > 0) { |
63656b762 dm: i2c: Implemen... |
663 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
664 |
ret = dm_i2c_write(dev, addr++, &byte, 1); |
63656b762 dm: i2c: Implemen... |
665 666 667 668 |
#else ret = i2c_write(chip, addr++, alen, &byte, 1); #endif if (ret) |
9e533cb04 cmd_i2c: quit I2C... |
669 |
return i2c_report_err(ret, I2C_ERR_WRITE); |
81a8824f2 Initial revision |
670 671 672 |
/* * Wait for the write to complete. The write can take * up to 10mSec (we allow a little more time). |
81a8824f2 Initial revision |
673 |
*/ |
d4f5c7289 FRAM memory acces... |
674 675 676 |
/* * No write delay with FRAM devices. */ |
6d0f6bcf3 rename CFG_ macro... |
677 |
#if !defined(CONFIG_SYS_I2C_FRAM) |
81a8824f2 Initial revision |
678 |
udelay(11000); |
d4f5c7289 FRAM memory acces... |
679 |
#endif |
81a8824f2 Initial revision |
680 |
} |
06afa388b i2c: kerneldoc: A... |
681 |
return 0; |
81a8824f2 Initial revision |
682 |
} |
06afa388b i2c: kerneldoc: A... |
683 684 685 686 687 688 689 690 691 692 693 |
/** * do_i2c_crc() - Handle the "i2c crc32" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Calculate a CRC on memory * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. |
81a8824f2 Initial revision |
694 695 |
* * Syntax: |
0f89c54be i2c: Update refer... |
696 |
* i2c crc32 {i2c_chip} {addr}{.0, .1, .2} {count} |
81a8824f2 Initial revision |
697 |
*/ |
54841ab50 Make sure that ar... |
698 |
static int do_i2c_crc (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
699 |
{ |
5468461d1 cmd_i2c: change v... |
700 |
uint chip; |
81a8824f2 Initial revision |
701 |
ulong addr; |
63656b762 dm: i2c: Implemen... |
702 |
int alen; |
81a8824f2 Initial revision |
703 704 705 706 |
int count; uchar byte; ulong crc; ulong err; |
63656b762 dm: i2c: Implemen... |
707 708 709 710 |
int ret = 0; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
81a8824f2 Initial revision |
711 |
|
47e26b1bf cmd_usage(): simp... |
712 |
if (argc < 4) |
4c12eeb8b Convert cmd_usage... |
713 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
714 715 |
/* |
53677ef18 Big white-space c... |
716 717 |
* Chip is always specified. */ |
81a8824f2 Initial revision |
718 719 720 721 722 723 |
chip = simple_strtoul(argv[1], NULL, 16); /* * Address is always specified. */ addr = simple_strtoul(argv[2], NULL, 16); |
63656b762 dm: i2c: Implemen... |
724 |
alen = get_alen(argv[2], DEFAULT_ADDR_LEN); |
7a92e53cd CMD_I2C: make ale... |
725 |
if (alen > 3) |
4c12eeb8b Convert cmd_usage... |
726 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
727 |
|
63656b762 dm: i2c: Implemen... |
728 729 730 731 732 733 734 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (ret) return i2c_report_err(ret, I2C_ERR_READ); #endif |
81a8824f2 Initial revision |
735 736 737 738 739 740 741 742 743 744 745 746 |
/* * Count is always specified */ count = simple_strtoul(argv[3], NULL, 16); printf ("CRC32 for %08lx ... %08lx ==> ", addr, addr + count - 1); /* * CRC a byte at a time. This is going to be slooow, but hey, the * memories are small and slow too so hopefully nobody notices. */ crc = 0; err = 0; |
e857a5bdb mpc83xx: Miscella... |
747 |
while (count-- > 0) { |
63656b762 dm: i2c: Implemen... |
748 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
749 |
ret = dm_i2c_read(dev, addr, &byte, 1); |
63656b762 dm: i2c: Implemen... |
750 751 752 753 |
#else ret = i2c_read(chip, addr, alen, &byte, 1); #endif if (ret) |
81a8824f2 Initial revision |
754 |
err++; |
81a8824f2 Initial revision |
755 756 757 |
crc = crc32 (crc, &byte, 1); addr++; } |
e857a5bdb mpc83xx: Miscella... |
758 |
if (err > 0) |
63656b762 dm: i2c: Implemen... |
759 |
i2c_report_err(ret, I2C_ERR_READ); |
e857a5bdb mpc83xx: Miscella... |
760 |
else |
81a8824f2 Initial revision |
761 762 |
printf ("%08lx ", crc); |
81a8824f2 Initial revision |
763 764 765 |
return 0; } |
06afa388b i2c: kerneldoc: A... |
766 767 768 769 770 771 772 773 774 775 776 |
/** * mod_i2c_mem() - Handle the "i2c mm" and "i2c nm" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Modify memory. * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. |
81a8824f2 Initial revision |
777 778 |
* * Syntax: |
0f89c54be i2c: Update refer... |
779 780 |
* i2c mm{.b, .w, .l} {i2c_chip} {addr}{.0, .1, .2} * i2c nm{.b, .w, .l} {i2c_chip} {addr}{.0, .1, .2} |
81a8824f2 Initial revision |
781 |
*/ |
81a8824f2 Initial revision |
782 |
static int |
54841ab50 Make sure that ar... |
783 |
mod_i2c_mem(cmd_tbl_t *cmdtp, int incrflag, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
784 |
{ |
5468461d1 cmd_i2c: change v... |
785 |
uint chip; |
81a8824f2 Initial revision |
786 |
ulong addr; |
63656b762 dm: i2c: Implemen... |
787 |
int alen; |
81a8824f2 Initial revision |
788 789 790 |
ulong data; int size = 1; int nbytes; |
63656b762 dm: i2c: Implemen... |
791 792 793 794 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
81a8824f2 Initial revision |
795 |
|
47e26b1bf cmd_usage(): simp... |
796 |
if (argc != 3) |
4c12eeb8b Convert cmd_usage... |
797 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
798 |
|
b26440f1f Rename bootretry ... |
799 |
bootretry_reset_cmd_timeout(); /* got a good command to get here */ |
81a8824f2 Initial revision |
800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 |
/* * We use the last specified parameters, unless new ones are * entered. */ chip = i2c_mm_last_chip; addr = i2c_mm_last_addr; alen = i2c_mm_last_alen; if ((flag & CMD_FLAG_REPEAT) == 0) { /* * New command specified. Check for a size specification. * Defaults to byte if no or incorrect specification. */ size = cmd_get_data_size(argv[0], 1); /* |
53677ef18 Big white-space c... |
816 817 |
* Chip is always specified. */ |
81a8824f2 Initial revision |
818 819 820 821 822 823 |
chip = simple_strtoul(argv[1], NULL, 16); /* * Address is always specified. */ addr = simple_strtoul(argv[2], NULL, 16); |
63656b762 dm: i2c: Implemen... |
824 |
alen = get_alen(argv[2], DEFAULT_ADDR_LEN); |
7a92e53cd CMD_I2C: make ale... |
825 |
if (alen > 3) |
4c12eeb8b Convert cmd_usage... |
826 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
827 |
} |
63656b762 dm: i2c: Implemen... |
828 829 830 831 832 833 834 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (ret) return i2c_report_err(ret, I2C_ERR_WRITE); #endif |
81a8824f2 Initial revision |
835 836 837 838 839 840 |
/* * Print the address, followed by value. Then accept input for * the next value. A non-converted value exits. */ do { printf("%08lx:", addr); |
63656b762 dm: i2c: Implemen... |
841 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
842 |
ret = dm_i2c_read(dev, addr, (uchar *)&data, size); |
63656b762 dm: i2c: Implemen... |
843 844 845 846 |
#else ret = i2c_read(chip, addr, alen, (uchar *)&data, size); #endif if (ret) |
9e533cb04 cmd_i2c: quit I2C... |
847 848 849 850 851 852 853 854 855 |
return i2c_report_err(ret, I2C_ERR_READ); data = cpu_to_be32(data); if (size == 1) printf(" %02lx", (data >> 24) & 0x000000FF); else if (size == 2) printf(" %04lx", (data >> 16) & 0x0000FFFF); else printf(" %08lx", data); |
81a8824f2 Initial revision |
856 |
|
e1bf824df Add cli_ prefix t... |
857 |
nbytes = cli_readline(" ? "); |
81a8824f2 Initial revision |
858 859 860 861 862 863 864 865 |
if (nbytes == 0) { /* * <CR> pressed as only input, don't modify current * location and move to next. */ if (incrflag) addr += size; nbytes = size; |
b26440f1f Rename bootretry ... |
866 867 |
/* good enough to not time out */ bootretry_reset_cmd_timeout(); |
81a8824f2 Initial revision |
868 869 |
} #ifdef CONFIG_BOOT_RETRY_TIME |
e857a5bdb mpc83xx: Miscella... |
870 |
else if (nbytes == -2) |
81a8824f2 Initial revision |
871 |
break; /* timed out, exit the command */ |
81a8824f2 Initial revision |
872 873 874 875 876 |
#endif else { char *endp; data = simple_strtoul(console_buffer, &endp, 16); |
e857a5bdb mpc83xx: Miscella... |
877 |
if (size == 1) |
81a8824f2 Initial revision |
878 |
data = data << 24; |
e857a5bdb mpc83xx: Miscella... |
879 |
else if (size == 2) |
81a8824f2 Initial revision |
880 |
data = data << 16; |
81a8824f2 Initial revision |
881 882 883 |
data = be32_to_cpu(data); nbytes = endp - console_buffer; if (nbytes) { |
81a8824f2 Initial revision |
884 885 886 |
/* * good enough to not time out */ |
b26440f1f Rename bootretry ... |
887 |
bootretry_reset_cmd_timeout(); |
63656b762 dm: i2c: Implemen... |
888 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
889 890 |
ret = dm_i2c_write(dev, addr, (uchar *)&data, size); |
63656b762 dm: i2c: Implemen... |
891 892 893 894 895 |
#else ret = i2c_write(chip, addr, alen, (uchar *)&data, size); #endif if (ret) |
9e533cb04 cmd_i2c: quit I2C... |
896 897 |
return i2c_report_err(ret, I2C_ERR_WRITE); |
6d0f6bcf3 rename CFG_ macro... |
898 899 |
#ifdef CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS udelay(CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS * 1000); |
2535d6027 * Patch by Martin... |
900 |
#endif |
81a8824f2 Initial revision |
901 902 903 904 905 |
if (incrflag) addr += size; } } } while (nbytes); |
0800707b6 mod_i2c_mem() bugfix |
906 907 908 |
i2c_mm_last_chip = chip; i2c_mm_last_addr = addr; i2c_mm_last_alen = alen; |
81a8824f2 Initial revision |
909 910 911 |
return 0; } |
06afa388b i2c: kerneldoc: A... |
912 913 914 915 916 917 918 919 920 921 |
/** * do_i2c_probe() - Handle the "i2c probe" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. * |
81a8824f2 Initial revision |
922 |
* Syntax: |
54b99e51a i2c_probe: update... |
923 924 925 |
* i2c probe {addr} * * Returns zero (success) if one or more I2C devices was found |
81a8824f2 Initial revision |
926 |
*/ |
54841ab50 Make sure that ar... |
927 |
static int do_i2c_probe (cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
928 929 |
{ int j; |
54b99e51a i2c_probe: update... |
930 931 |
int addr = -1; int found = 0; |
6d0f6bcf3 rename CFG_ macro... |
932 |
#if defined(CONFIG_SYS_I2C_NOPROBES) |
81a8824f2 Initial revision |
933 |
int k, skip; |
3f4978c71 i2c: common chang... |
934 |
unsigned int bus = GET_BUS_NUM; |
bb99ad6d8 Add support for m... |
935 |
#endif /* NOPROBES */ |
63656b762 dm: i2c: Implemen... |
936 937 938 939 940 941 942 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *bus, *dev; if (i2c_get_cur_bus(&bus)) return CMD_RET_FAILURE; #endif |
81a8824f2 Initial revision |
943 |
|
54b99e51a i2c_probe: update... |
944 945 |
if (argc == 2) addr = simple_strtol(argv[1], 0, 16); |
4b9206ed5 * Patches by Thom... |
946 |
puts ("Valid chip addresses:"); |
e857a5bdb mpc83xx: Miscella... |
947 |
for (j = 0; j < 128; j++) { |
54b99e51a i2c_probe: update... |
948 949 |
if ((0 <= addr) && (j != addr)) continue; |
6d0f6bcf3 rename CFG_ macro... |
950 |
#if defined(CONFIG_SYS_I2C_NOPROBES) |
81a8824f2 Initial revision |
951 |
skip = 0; |
cfb25cc40 cmd_i2c: Use ARRA... |
952 |
for (k = 0; k < ARRAY_SIZE(i2c_no_probes); k++) { |
e857a5bdb mpc83xx: Miscella... |
953 |
if (COMPARE_BUS(bus, k) && COMPARE_ADDR(j, k)) { |
81a8824f2 Initial revision |
954 955 956 957 958 959 960 |
skip = 1; break; } } if (skip) continue; #endif |
63656b762 dm: i2c: Implemen... |
961 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
962 |
ret = dm_i2c_probe(bus, j, 0, &dev); |
63656b762 dm: i2c: Implemen... |
963 964 965 966 |
#else ret = i2c_probe(j); #endif if (ret == 0) { |
81a8824f2 Initial revision |
967 |
printf(" %02X", j); |
54b99e51a i2c_probe: update... |
968 969 |
found++; } |
81a8824f2 Initial revision |
970 |
} |
4b9206ed5 * Patches by Thom... |
971 972 |
putc (' '); |
81a8824f2 Initial revision |
973 |
|
6d0f6bcf3 rename CFG_ macro... |
974 |
#if defined(CONFIG_SYS_I2C_NOPROBES) |
81a8824f2 Initial revision |
975 |
puts ("Excluded chip addresses:"); |
cfb25cc40 cmd_i2c: Use ARRA... |
976 |
for (k = 0; k < ARRAY_SIZE(i2c_no_probes); k++) { |
e857a5bdb mpc83xx: Miscella... |
977 |
if (COMPARE_BUS(bus,k)) |
bb99ad6d8 Add support for m... |
978 979 |
printf(" %02X", NO_PROBE_ADDR(k)); } |
4b9206ed5 * Patches by Thom... |
980 981 |
putc (' '); |
81a8824f2 Initial revision |
982 |
#endif |
54b99e51a i2c_probe: update... |
983 |
return (0 == found); |
81a8824f2 Initial revision |
984 |
} |
06afa388b i2c: kerneldoc: A... |
985 986 987 988 989 990 991 992 993 994 |
/** * do_i2c_loop() - Handle the "i2c loop" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. * |
81a8824f2 Initial revision |
995 |
* Syntax: |
0f89c54be i2c: Update refer... |
996 |
* i2c loop {i2c_chip} {addr}{.0, .1, .2} [{length}] [{delay}] |
81a8824f2 Initial revision |
997 998 999 |
* {length} - Number of bytes to read * {delay} - A DECIMAL number and defaults to 1000 uSec */ |
54841ab50 Make sure that ar... |
1000 |
static int do_i2c_loop(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
1001 |
{ |
5468461d1 cmd_i2c: change v... |
1002 |
uint chip; |
63656b762 dm: i2c: Implemen... |
1003 |
int alen; |
81a8824f2 Initial revision |
1004 1005 1006 1007 |
uint addr; uint length; u_char bytes[16]; int delay; |
63656b762 dm: i2c: Implemen... |
1008 1009 1010 1011 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
81a8824f2 Initial revision |
1012 |
|
47e26b1bf cmd_usage(): simp... |
1013 |
if (argc < 3) |
4c12eeb8b Convert cmd_usage... |
1014 |
return CMD_RET_USAGE; |
81a8824f2 Initial revision |
1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 |
/* * Chip is always specified. */ chip = simple_strtoul(argv[1], NULL, 16); /* * Address is always specified. */ addr = simple_strtoul(argv[2], NULL, 16); |
63656b762 dm: i2c: Implemen... |
1025 |
alen = get_alen(argv[2], DEFAULT_ADDR_LEN); |
7a92e53cd CMD_I2C: make ale... |
1026 |
if (alen > 3) |
4c12eeb8b Convert cmd_usage... |
1027 |
return CMD_RET_USAGE; |
63656b762 dm: i2c: Implemen... |
1028 1029 1030 1031 1032 1033 1034 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret && alen != -1) ret = i2c_set_chip_offset_len(dev, alen); if (ret) return i2c_report_err(ret, I2C_ERR_WRITE); #endif |
81a8824f2 Initial revision |
1035 1036 1037 1038 1039 1040 |
/* * Length is the number of objects, not number of bytes. */ length = 1; length = simple_strtoul(argv[3], NULL, 16); |
e857a5bdb mpc83xx: Miscella... |
1041 |
if (length > sizeof(bytes)) |
81a8824f2 Initial revision |
1042 |
length = sizeof(bytes); |
81a8824f2 Initial revision |
1043 1044 1045 1046 1047 |
/* * The delay time (uSec) is optional. */ delay = 1000; |
e857a5bdb mpc83xx: Miscella... |
1048 |
if (argc > 3) |
81a8824f2 Initial revision |
1049 |
delay = simple_strtoul(argv[4], NULL, 10); |
81a8824f2 Initial revision |
1050 1051 1052 |
/* * Run the loop... */ |
e857a5bdb mpc83xx: Miscella... |
1053 |
while (1) { |
63656b762 dm: i2c: Implemen... |
1054 |
#ifdef CONFIG_DM_I2C |
f9a4c2da7 dm: i2c: Rename d... |
1055 |
ret = dm_i2c_read(dev, addr, bytes, length); |
63656b762 dm: i2c: Implemen... |
1056 1057 1058 1059 1060 |
#else ret = i2c_read(chip, addr, alen, bytes, length); #endif if (ret) i2c_report_err(ret, I2C_ERR_READ); |
81a8824f2 Initial revision |
1061 1062 1063 1064 1065 1066 |
udelay(delay); } /* NOTREACHED */ return 0; } |
81a8824f2 Initial revision |
1067 1068 1069 |
/* * The SDRAM command is separately configured because many * (most?) embedded boards don't use SDRAM DIMMs. |
06afa388b i2c: kerneldoc: A... |
1070 1071 |
* * FIXME: Document and probably move elsewhere! |
81a8824f2 Initial revision |
1072 |
*/ |
c76fe4742 common/cmd_[i-n]*... |
1073 |
#if defined(CONFIG_CMD_SDRAM) |
632de0672 Refactor code for... |
1074 1075 1076 1077 1078 1079 1080 1081 1082 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094 1095 1096 1097 1098 1099 1100 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1121 1122 1123 1124 1125 |
static void print_ddr2_tcyc (u_char const b) { printf ("%d.", (b >> 4) & 0x0F); switch (b & 0x0F) { case 0x0: case 0x1: case 0x2: case 0x3: case 0x4: case 0x5: case 0x6: case 0x7: case 0x8: case 0x9: printf ("%d ns ", b & 0x0F); break; case 0xA: puts ("25 ns "); break; case 0xB: puts ("33 ns "); break; case 0xC: puts ("66 ns "); break; case 0xD: puts ("75 ns "); break; default: puts ("?? ns "); break; } } static void decode_bits (u_char const b, char const *str[], int const do_once) { u_char mask; for (mask = 0x80; mask != 0x00; mask >>= 1, ++str) { if (b & mask) { puts (*str); if (do_once) return; } } } |
81a8824f2 Initial revision |
1126 1127 1128 |
/* * Syntax: |
0f89c54be i2c: Update refer... |
1129 |
* i2c sdram {i2c_chip} |
81a8824f2 Initial revision |
1130 |
*/ |
54841ab50 Make sure that ar... |
1131 |
static int do_sdram (cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) |
81a8824f2 Initial revision |
1132 |
{ |
18c4e7f71 i2c: spd: Extend ... |
1133 |
enum { unknown, EDO, SDRAM, DDR, DDR2, DDR3, DDR4 } type; |
632de0672 Refactor code for... |
1134 |
|
5468461d1 cmd_i2c: change v... |
1135 |
uint chip; |
81a8824f2 Initial revision |
1136 1137 |
u_char data[128]; u_char cksum; |
28df8ed07 cmd: i2c: Fix use... |
1138 1139 1140 1141 |
int j, ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
81a8824f2 Initial revision |
1142 |
|
632de0672 Refactor code for... |
1143 1144 1145 1146 1147 1148 1149 1150 1151 1152 1153 1154 1155 1156 1157 1158 1159 1160 1161 1162 1163 1164 1165 1166 1167 1168 1169 1170 1171 1172 1173 1174 1175 1176 1177 1178 1179 1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 |
static const char *decode_CAS_DDR2[] = { " TBD", " 6", " 5", " 4", " 3", " 2", " TBD", " TBD" }; static const char *decode_CAS_default[] = { " TBD", " 7", " 6", " 5", " 4", " 3", " 2", " 1" }; static const char *decode_CS_WE_default[] = { " TBD", " 6", " 5", " 4", " 3", " 2", " 1", " 0" }; static const char *decode_byte21_default[] = { " TBD (bit 7) ", " Redundant row address ", " Differential clock input ", " Registerd DQMB inputs ", " Buffered DQMB inputs ", " On-card PLL ", " Registered address/control lines ", " Buffered address/control lines " }; static const char *decode_byte22_DDR2[] = { " TBD (bit 7) ", " TBD (bit 6) ", " TBD (bit 5) ", " TBD (bit 4) ", " TBD (bit 3) ", " Supports partial array self refresh ", " Supports 50 ohm ODT ", " Supports weak driver " }; static const char *decode_row_density_DDR2[] = { "512 MiB", "256 MiB", "128 MiB", "16 GiB", "8 GiB", "4 GiB", "2 GiB", "1 GiB" }; static const char *decode_row_density_default[] = { "512 MiB", "256 MiB", "128 MiB", "64 MiB", "32 MiB", "16 MiB", "8 MiB", "4 MiB" }; |
47e26b1bf cmd_usage(): simp... |
1202 |
if (argc < 2) |
4c12eeb8b Convert cmd_usage... |
1203 |
return CMD_RET_USAGE; |
47e26b1bf cmd_usage(): simp... |
1204 |
|
81a8824f2 Initial revision |
1205 1206 |
/* * Chip is always specified. |
632de0672 Refactor code for... |
1207 1208 |
*/ chip = simple_strtoul (argv[1], NULL, 16); |
81a8824f2 Initial revision |
1209 |
|
28df8ed07 cmd: i2c: Fix use... |
1210 1211 1212 1213 1214 1215 1216 1217 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret) ret = dm_i2c_read(dev, 0, data, sizeof(data)); #else ret = i2c_read(chip, 0, 1, data, sizeof(data)); #endif if (ret) { |
4b9206ed5 * Patches by Thom... |
1218 1219 |
puts ("No SDRAM Serial Presence Detect found. "); |
81a8824f2 Initial revision |
1220 1221 1222 1223 1224 1225 1226 |
return 1; } cksum = 0; for (j = 0; j < 63; j++) { cksum += data[j]; } |
e857a5bdb mpc83xx: Miscella... |
1227 |
if (cksum != data[63]) { |
81a8824f2 Initial revision |
1228 1229 |
printf ("WARNING: Configuration data checksum failure: " |
632de0672 Refactor code for... |
1230 1231 |
" is 0x%02x, calculated 0x%02x ", data[63], cksum); |
81a8824f2 Initial revision |
1232 |
} |
632de0672 Refactor code for... |
1233 1234 |
printf ("SPD data revision %d.%d ", |
81a8824f2 Initial revision |
1235 |
(data[62] >> 4) & 0x0F, data[62] & 0x0F); |
632de0672 Refactor code for... |
1236 1237 1238 1239 |
printf ("Bytes used 0x%02X ", data[0]); printf ("Serial memory size 0x%02X ", 1 << data[1]); |
4b9206ed5 * Patches by Thom... |
1240 |
puts ("Memory type "); |
632de0672 Refactor code for... |
1241 |
switch (data[2]) { |
0df6b8446 Fix "i2c sdram" c... |
1242 1243 1244 1245 1246 1247 1248 1249 1250 1251 |
case 2: type = EDO; puts ("EDO "); break; case 4: type = SDRAM; puts ("SDRAM "); break; |
18c4e7f71 i2c: spd: Extend ... |
1252 1253 1254 1255 1256 |
case 7: type = DDR; puts("DDR "); break; |
0df6b8446 Fix "i2c sdram" c... |
1257 1258 1259 1260 1261 |
case 8: type = DDR2; puts ("DDR2 "); break; |
18c4e7f71 i2c: spd: Extend ... |
1262 1263 1264 1265 1266 1267 1268 1269 1270 1271 |
case 11: type = DDR3; puts("DDR3 "); break; case 12: type = DDR4; puts("DDR4 "); break; |
0df6b8446 Fix "i2c sdram" c... |
1272 1273 1274 1275 1276 |
default: type = unknown; puts ("unknown "); break; |
81a8824f2 Initial revision |
1277 |
} |
632de0672 Refactor code for... |
1278 |
|
4b9206ed5 * Patches by Thom... |
1279 |
puts ("Row address bits "); |
e857a5bdb mpc83xx: Miscella... |
1280 |
if ((data[3] & 0x00F0) == 0) |
632de0672 Refactor code for... |
1281 1282 |
printf ("%d ", data[3] & 0x0F); |
e857a5bdb mpc83xx: Miscella... |
1283 |
else |
632de0672 Refactor code for... |
1284 1285 |
printf ("%d/%d ", data[3] & 0x0F, (data[3] >> 4) & 0x0F); |
4b9206ed5 * Patches by Thom... |
1286 |
puts ("Column address bits "); |
e857a5bdb mpc83xx: Miscella... |
1287 |
if ((data[4] & 0x00F0) == 0) |
632de0672 Refactor code for... |
1288 1289 |
printf ("%d ", data[4] & 0x0F); |
e857a5bdb mpc83xx: Miscella... |
1290 |
else |
632de0672 Refactor code for... |
1291 1292 |
printf ("%d/%d ", data[4] & 0x0F, (data[4] >> 4) & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1293 1294 1295 |
switch (type) { case DDR2: |
632de0672 Refactor code for... |
1296 1297 1298 |
printf ("Number of ranks %d ", (data[5] & 0x07) + 1); |
0df6b8446 Fix "i2c sdram" c... |
1299 1300 |
break; default: |
632de0672 Refactor code for... |
1301 1302 |
printf ("Module rows %d ", data[5]); |
0df6b8446 Fix "i2c sdram" c... |
1303 1304 1305 1306 1307 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1308 1309 |
printf ("Module data width %d bits ", data[6]); |
0df6b8446 Fix "i2c sdram" c... |
1310 1311 |
break; default: |
632de0672 Refactor code for... |
1312 1313 1314 |
printf ("Module data width %d bits ", (data[7] << 8) | data[6]); |
0df6b8446 Fix "i2c sdram" c... |
1315 1316 |
break; } |
4b9206ed5 * Patches by Thom... |
1317 |
puts ("Interface signal levels "); |
81a8824f2 Initial revision |
1318 |
switch(data[8]) { |
0df6b8446 Fix "i2c sdram" c... |
1319 1320 |
case 0: puts ("TTL 5.0 V "); break; |
4b9206ed5 * Patches by Thom... |
1321 1322 |
case 1: puts ("LVTTL "); break; |
0df6b8446 Fix "i2c sdram" c... |
1323 1324 1325 1326 1327 1328 1329 1330 |
case 2: puts ("HSTL 1.5 V "); break; case 3: puts ("SSTL 3.3 V "); break; case 4: puts ("SSTL 2.5 V "); break; case 5: puts ("SSTL 1.8 V "); break; |
4b9206ed5 * Patches by Thom... |
1331 1332 |
default: puts ("unknown "); break; |
81a8824f2 Initial revision |
1333 |
} |
0df6b8446 Fix "i2c sdram" c... |
1334 1335 1336 |
switch (type) { case DDR2: |
632de0672 Refactor code for... |
1337 1338 |
printf ("SDRAM cycle time "); print_ddr2_tcyc (data[9]); |
0df6b8446 Fix "i2c sdram" c... |
1339 1340 |
break; default: |
632de0672 Refactor code for... |
1341 1342 1343 |
printf ("SDRAM cycle time %d.%d ns ", (data[9] >> 4) & 0x0F, data[9] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1344 1345 1346 1347 1348 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1349 1350 1351 |
printf ("SDRAM access time 0.%d%d ns ", (data[10] >> 4) & 0x0F, data[10] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1352 1353 |
break; default: |
632de0672 Refactor code for... |
1354 1355 1356 |
printf ("SDRAM access time %d.%d ns ", (data[10] >> 4) & 0x0F, data[10] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1357 1358 |
break; } |
4b9206ed5 * Patches by Thom... |
1359 |
puts ("EDC configuration "); |
632de0672 Refactor code for... |
1360 |
switch (data[11]) { |
4b9206ed5 * Patches by Thom... |
1361 1362 1363 1364 1365 1366 1367 1368 |
case 0: puts ("None "); break; case 1: puts ("Parity "); break; case 2: puts ("ECC "); break; default: puts ("unknown "); break; |
81a8824f2 Initial revision |
1369 |
} |
632de0672 Refactor code for... |
1370 |
|
e857a5bdb mpc83xx: Miscella... |
1371 |
if ((data[12] & 0x80) == 0) |
4b9206ed5 * Patches by Thom... |
1372 |
puts ("No self refresh, rate "); |
e857a5bdb mpc83xx: Miscella... |
1373 |
else |
4b9206ed5 * Patches by Thom... |
1374 |
puts ("Self refresh, rate "); |
632de0672 Refactor code for... |
1375 |
|
81a8824f2 Initial revision |
1376 |
switch(data[12] & 0x7F) { |
632de0672 Refactor code for... |
1377 1378 1379 1380 1381 1382 1383 1384 1385 1386 1387 1388 |
case 0: puts ("15.625 us "); break; case 1: puts ("3.9 us "); break; case 2: puts ("7.8 us "); break; case 3: puts ("31.3 us "); break; case 4: puts ("62.5 us "); break; case 5: puts ("125 us "); break; |
4b9206ed5 * Patches by Thom... |
1389 1390 |
default: puts ("unknown "); break; |
81a8824f2 Initial revision |
1391 |
} |
0df6b8446 Fix "i2c sdram" c... |
1392 1393 1394 |
switch (type) { case DDR2: |
632de0672 Refactor code for... |
1395 1396 |
printf ("SDRAM width (primary) %d ", data[13]); |
0df6b8446 Fix "i2c sdram" c... |
1397 1398 |
break; default: |
632de0672 Refactor code for... |
1399 1400 |
printf ("SDRAM width (primary) %d ", data[13] & 0x7F); |
0df6b8446 Fix "i2c sdram" c... |
1401 |
if ((data[13] & 0x80) != 0) { |
632de0672 Refactor code for... |
1402 1403 1404 |
printf (" (second bank) %d ", 2 * (data[13] & 0x7F)); |
0df6b8446 Fix "i2c sdram" c... |
1405 1406 1407 1408 1409 1410 1411 |
} break; } switch (type) { case DDR2: if (data[14] != 0) |
632de0672 Refactor code for... |
1412 1413 |
printf ("EDC width %d ", data[14]); |
0df6b8446 Fix "i2c sdram" c... |
1414 1415 1416 |
break; default: if (data[14] != 0) { |
632de0672 Refactor code for... |
1417 1418 1419 |
printf ("EDC width %d ", data[14] & 0x7F); |
0df6b8446 Fix "i2c sdram" c... |
1420 1421 |
if ((data[14] & 0x80) != 0) { |
632de0672 Refactor code for... |
1422 1423 1424 |
printf (" (second bank) %d ", 2 * (data[14] & 0x7F)); |
0df6b8446 Fix "i2c sdram" c... |
1425 1426 1427 |
} } break; |
81a8824f2 Initial revision |
1428 |
} |
0df6b8446 Fix "i2c sdram" c... |
1429 |
|
632de0672 Refactor code for... |
1430 1431 1432 1433 |
if (DDR2 != type) { printf ("Min clock delay, back-to-back random column addresses " "%d ", data[15]); |
0df6b8446 Fix "i2c sdram" c... |
1434 |
} |
4b9206ed5 * Patches by Thom... |
1435 1436 1437 1438 1439 1440 1441 1442 |
puts ("Burst length(s) "); if (data[16] & 0x80) puts (" Page"); if (data[16] & 0x08) puts (" 8"); if (data[16] & 0x04) puts (" 4"); if (data[16] & 0x02) puts (" 2"); if (data[16] & 0x01) puts (" 1"); putc (' '); |
632de0672 Refactor code for... |
1443 1444 |
printf ("Number of banks %d ", data[17]); |
0df6b8446 Fix "i2c sdram" c... |
1445 1446 1447 1448 |
switch (type) { case DDR2: puts ("CAS latency(s) "); |
632de0672 Refactor code for... |
1449 |
decode_bits (data[18], decode_CAS_DDR2, 0); |
0df6b8446 Fix "i2c sdram" c... |
1450 1451 1452 1453 1454 |
putc (' '); break; default: puts ("CAS latency(s) "); |
632de0672 Refactor code for... |
1455 |
decode_bits (data[18], decode_CAS_default, 0); |
0df6b8446 Fix "i2c sdram" c... |
1456 1457 1458 1459 1460 1461 1462 |
putc (' '); break; } if (DDR2 != type) { puts ("CS latency(s) "); |
632de0672 Refactor code for... |
1463 |
decode_bits (data[19], decode_CS_WE_default, 0); |
0df6b8446 Fix "i2c sdram" c... |
1464 1465 1466 1467 1468 1469 |
putc (' '); } if (DDR2 != type) { puts ("WE latency(s) "); |
632de0672 Refactor code for... |
1470 |
decode_bits (data[20], decode_CS_WE_default, 0); |
0df6b8446 Fix "i2c sdram" c... |
1471 1472 1473 1474 1475 1476 1477 1478 1479 1480 1481 1482 1483 1484 1485 1486 1487 1488 1489 1490 |
putc (' '); } switch (type) { case DDR2: puts ("Module attributes: "); if (data[21] & 0x80) puts (" TBD (bit 7) "); if (data[21] & 0x40) puts (" Analysis probe installed "); if (data[21] & 0x20) puts (" TBD (bit 5) "); if (data[21] & 0x10) puts (" FET switch external enable "); |
632de0672 Refactor code for... |
1491 1492 |
printf (" %d PLLs on DIMM ", (data[21] >> 2) & 0x03); |
0df6b8446 Fix "i2c sdram" c... |
1493 |
if (data[20] & 0x11) { |
632de0672 Refactor code for... |
1494 1495 1496 |
printf (" %d active registers on DIMM ", (data[21] & 0x03) + 1); |
0df6b8446 Fix "i2c sdram" c... |
1497 1498 1499 1500 1501 1502 1503 1504 |
} break; default: puts ("Module attributes: "); if (!data[21]) puts (" (none) "); |
632de0672 Refactor code for... |
1505 1506 |
else decode_bits (data[21], decode_byte21_default, 0); |
0df6b8446 Fix "i2c sdram" c... |
1507 1508 1509 1510 1511 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1512 |
decode_bits (data[22], decode_byte22_DDR2, 0); |
0df6b8446 Fix "i2c sdram" c... |
1513 1514 1515 1516 1517 1518 1519 1520 1521 1522 1523 1524 1525 1526 1527 1528 1529 1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 |
break; default: puts ("Device attributes: "); if (data[22] & 0x80) puts (" TBD (bit 7) "); if (data[22] & 0x40) puts (" TBD (bit 6) "); if (data[22] & 0x20) puts (" Upper Vcc tolerance 5% "); else puts (" Upper Vcc tolerance 10% "); if (data[22] & 0x10) puts (" Lower Vcc tolerance 5% "); else puts (" Lower Vcc tolerance 10% "); if (data[22] & 0x08) puts (" Supports write1/read burst "); if (data[22] & 0x04) puts (" Supports precharge all "); if (data[22] & 0x02) puts (" Supports auto precharge "); if (data[22] & 0x01) puts (" Supports early RAS# precharge "); break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1542 1543 |
printf ("SDRAM cycle time (2nd highest CAS latency) "); print_ddr2_tcyc (data[23]); |
0df6b8446 Fix "i2c sdram" c... |
1544 1545 |
break; default: |
632de0672 Refactor code for... |
1546 1547 1548 |
printf ("SDRAM cycle time (2nd highest CAS latency) %d." "%d ns ", (data[23] >> 4) & 0x0F, data[23] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1549 1550 1551 1552 1553 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1554 1555 1556 |
printf ("SDRAM access from clock (2nd highest CAS latency) 0." "%d%d ns ", (data[24] >> 4) & 0x0F, data[24] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1557 1558 |
break; default: |
632de0672 Refactor code for... |
1559 1560 1561 |
printf ("SDRAM access from clock (2nd highest CAS latency) %d." "%d ns ", (data[24] >> 4) & 0x0F, data[24] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1562 1563 1564 1565 1566 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1567 1568 |
printf ("SDRAM cycle time (3rd highest CAS latency) "); print_ddr2_tcyc (data[25]); |
0df6b8446 Fix "i2c sdram" c... |
1569 1570 |
break; default: |
632de0672 Refactor code for... |
1571 1572 1573 |
printf ("SDRAM cycle time (3rd highest CAS latency) %d." "%d ns ", (data[25] >> 4) & 0x0F, data[25] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1574 1575 1576 1577 1578 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1579 1580 1581 |
printf ("SDRAM access from clock (3rd highest CAS latency) 0." "%d%d ns ", (data[26] >> 4) & 0x0F, data[26] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1582 1583 |
break; default: |
632de0672 Refactor code for... |
1584 1585 1586 |
printf ("SDRAM access from clock (3rd highest CAS latency) %d." "%d ns ", (data[26] >> 4) & 0x0F, data[26] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1587 1588 1589 1590 1591 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1592 1593 1594 |
printf ("Minimum row precharge %d.%02d ns ", (data[27] >> 2) & 0x3F, 25 * (data[27] & 0x03)); |
0df6b8446 Fix "i2c sdram" c... |
1595 1596 |
break; default: |
632de0672 Refactor code for... |
1597 1598 |
printf ("Minimum row precharge %d ns ", data[27]); |
0df6b8446 Fix "i2c sdram" c... |
1599 1600 1601 1602 1603 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1604 1605 1606 |
printf ("Row active to row active min %d.%02d ns ", (data[28] >> 2) & 0x3F, 25 * (data[28] & 0x03)); |
0df6b8446 Fix "i2c sdram" c... |
1607 1608 |
break; default: |
632de0672 Refactor code for... |
1609 1610 |
printf ("Row active to row active min %d ns ", data[28]); |
0df6b8446 Fix "i2c sdram" c... |
1611 1612 1613 1614 1615 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1616 1617 1618 |
printf ("RAS to CAS delay min %d.%02d ns ", (data[29] >> 2) & 0x3F, 25 * (data[29] & 0x03)); |
0df6b8446 Fix "i2c sdram" c... |
1619 1620 |
break; default: |
632de0672 Refactor code for... |
1621 1622 |
printf ("RAS to CAS delay min %d ns ", data[29]); |
0df6b8446 Fix "i2c sdram" c... |
1623 1624 |
break; } |
632de0672 Refactor code for... |
1625 1626 |
printf ("Minimum RAS pulse width %d ns ", data[30]); |
0df6b8446 Fix "i2c sdram" c... |
1627 1628 1629 |
switch (type) { case DDR2: |
632de0672 Refactor code for... |
1630 1631 1632 1633 |
puts ("Density of each row "); decode_bits (data[31], decode_row_density_DDR2, 1); putc (' '); |
0df6b8446 Fix "i2c sdram" c... |
1634 1635 |
break; default: |
632de0672 Refactor code for... |
1636 1637 1638 1639 |
puts ("Density of each row "); decode_bits (data[31], decode_row_density_default, 1); putc (' '); |
0df6b8446 Fix "i2c sdram" c... |
1640 1641 1642 1643 1644 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1645 |
puts ("Command and Address setup "); |
0df6b8446 Fix "i2c sdram" c... |
1646 |
if (data[32] >= 0xA0) { |
632de0672 Refactor code for... |
1647 1648 1649 |
printf ("1.%d%d ns ", ((data[32] >> 4) & 0x0F) - 10, data[32] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1650 |
} else { |
632de0672 Refactor code for... |
1651 1652 1653 |
printf ("0.%d%d ns ", ((data[32] >> 4) & 0x0F), data[32] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1654 1655 1656 |
} break; default: |
632de0672 Refactor code for... |
1657 1658 1659 1660 |
printf ("Command and Address setup %c%d.%d ns ", (data[32] & 0x80) ? '-' : '+', (data[32] >> 4) & 0x07, data[32] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1661 1662 1663 1664 1665 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1666 |
puts ("Command and Address hold "); |
0df6b8446 Fix "i2c sdram" c... |
1667 |
if (data[33] >= 0xA0) { |
632de0672 Refactor code for... |
1668 1669 1670 |
printf ("1.%d%d ns ", ((data[33] >> 4) & 0x0F) - 10, data[33] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1671 |
} else { |
632de0672 Refactor code for... |
1672 1673 1674 |
printf ("0.%d%d ns ", ((data[33] >> 4) & 0x0F), data[33] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1675 1676 1677 |
} break; default: |
632de0672 Refactor code for... |
1678 1679 1680 1681 |
printf ("Command and Address hold %c%d.%d ns ", (data[33] & 0x80) ? '-' : '+', (data[33] >> 4) & 0x07, data[33] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1682 1683 1684 1685 1686 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1687 1688 1689 |
printf ("Data signal input setup 0.%d%d ns ", (data[34] >> 4) & 0x0F, data[34] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1690 1691 |
break; default: |
632de0672 Refactor code for... |
1692 1693 1694 1695 |
printf ("Data signal input setup %c%d.%d ns ", (data[34] & 0x80) ? '-' : '+', (data[34] >> 4) & 0x07, data[34] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1696 1697 1698 1699 1700 |
break; } switch (type) { case DDR2: |
632de0672 Refactor code for... |
1701 1702 1703 |
printf ("Data signal input hold 0.%d%d ns ", (data[35] >> 4) & 0x0F, data[35] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1704 1705 |
break; default: |
632de0672 Refactor code for... |
1706 1707 1708 1709 |
printf ("Data signal input hold %c%d.%d ns ", (data[35] & 0x80) ? '-' : '+', (data[35] >> 4) & 0x07, data[35] & 0x0F); |
0df6b8446 Fix "i2c sdram" c... |
1710 1711 |
break; } |
4b9206ed5 * Patches by Thom... |
1712 |
puts ("Manufacturer's JEDEC ID "); |
e857a5bdb mpc83xx: Miscella... |
1713 |
for (j = 64; j <= 71; j++) |
632de0672 Refactor code for... |
1714 |
printf ("%02X ", data[j]); |
4b9206ed5 * Patches by Thom... |
1715 1716 |
putc (' '); |
632de0672 Refactor code for... |
1717 1718 |
printf ("Manufacturing Location %02X ", data[72]); |
4b9206ed5 * Patches by Thom... |
1719 |
puts ("Manufacturer's Part Number "); |
e857a5bdb mpc83xx: Miscella... |
1720 |
for (j = 73; j <= 90; j++) |
632de0672 Refactor code for... |
1721 |
printf ("%02X ", data[j]); |
4b9206ed5 * Patches by Thom... |
1722 1723 |
putc (' '); |
632de0672 Refactor code for... |
1724 1725 1726 1727 |
printf ("Revision Code %02X %02X ", data[91], data[92]); printf ("Manufacturing Date %02X %02X ", data[93], data[94]); |
4b9206ed5 * Patches by Thom... |
1728 |
puts ("Assembly Serial Number "); |
e857a5bdb mpc83xx: Miscella... |
1729 |
for (j = 95; j <= 98; j++) |
632de0672 Refactor code for... |
1730 |
printf ("%02X ", data[j]); |
4b9206ed5 * Patches by Thom... |
1731 1732 |
putc (' '); |
81a8824f2 Initial revision |
1733 |
|
0df6b8446 Fix "i2c sdram" c... |
1734 |
if (DDR2 != type) { |
632de0672 Refactor code for... |
1735 1736 1737 |
printf ("Speed rating PC%d ", data[126] == 0x66 ? 66 : data[126]); |
0df6b8446 Fix "i2c sdram" c... |
1738 |
} |
81a8824f2 Initial revision |
1739 1740 |
return 0; } |
902531788 common/: Remove l... |
1741 |
#endif |
81a8824f2 Initial revision |
1742 |
|
735987c5a edid: Add I2C com... |
1743 1744 1745 1746 1747 1748 1749 |
/* * Syntax: * i2c edid {i2c_chip} */ #if defined(CONFIG_I2C_EDID) int do_edid(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) { |
5468461d1 cmd_i2c: change v... |
1750 |
uint chip; |
735987c5a edid: Add I2C com... |
1751 |
struct edid1_info edid; |
63656b762 dm: i2c: Implemen... |
1752 1753 1754 1755 |
int ret; #ifdef CONFIG_DM_I2C struct udevice *dev; #endif |
735987c5a edid: Add I2C com... |
1756 1757 1758 1759 1760 1761 1762 |
if (argc < 2) { cmd_usage(cmdtp); return 1; } chip = simple_strtoul(argv[1], NULL, 16); |
63656b762 dm: i2c: Implemen... |
1763 1764 1765 |
#ifdef CONFIG_DM_I2C ret = i2c_get_cur_bus_chip(chip, &dev); if (!ret) |
f9a4c2da7 dm: i2c: Rename d... |
1766 |
ret = dm_i2c_read(dev, 0, (uchar *)&edid, sizeof(edid)); |
63656b762 dm: i2c: Implemen... |
1767 1768 1769 1770 1771 |
#else ret = i2c_read(chip, 0, 1, (uchar *)&edid, sizeof(edid)); #endif if (ret) return i2c_report_err(ret, I2C_ERR_READ); |
735987c5a edid: Add I2C com... |
1772 1773 1774 1775 1776 1777 1778 1779 1780 1781 1782 1783 |
if (edid_check_info(&edid)) { puts("Content isn't valid EDID. "); return 1; } edid_print_info(&edid); return 0; } #endif /* CONFIG_I2C_EDID */ |
59aa9df38 dm: i2c: Implemen... |
1784 1785 1786 1787 1788 1789 1790 1791 1792 1793 1794 1795 1796 1797 1798 1799 1800 1801 1802 1803 1804 1805 |
#ifdef CONFIG_DM_I2C static void show_bus(struct udevice *bus) { struct udevice *dev; printf("Bus %d:\t%s", bus->req_seq, bus->name); if (device_active(bus)) printf(" (active %d)", bus->seq); printf(" "); for (device_find_first_child(bus, &dev); dev; device_find_next_child(&dev)) { struct dm_i2c_chip *chip = dev_get_parent_platdata(dev); printf(" %02x: %s, offset len %x, flags %x ", chip->chip_addr, dev->name, chip->offset_len, chip->flags); } } #endif |
06afa388b i2c: kerneldoc: A... |
1806 |
/** |
3f4978c71 i2c: common chang... |
1807 |
* do_i2c_show_bus() - Handle the "i2c bus" command-line command |
06afa388b i2c: kerneldoc: A... |
1808 1809 1810 1811 1812 1813 1814 |
* @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero always. */ |
59aa9df38 dm: i2c: Implemen... |
1815 |
#if defined(CONFIG_SYS_I2C) || defined(CONFIG_DM_I2C) |
0e350f81e common: commands:... |
1816 1817 |
static int do_i2c_show_bus(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
67b23a322 I2C: adding new "... |
1818 |
{ |
67b23a322 I2C: adding new "... |
1819 1820 |
if (argc == 1) { /* show all busses */ |
59aa9df38 dm: i2c: Implemen... |
1821 1822 1823 1824 1825 1826 1827 1828 1829 1830 1831 1832 |
#ifdef CONFIG_DM_I2C struct udevice *bus; struct uclass *uc; int ret; ret = uclass_get(UCLASS_I2C, &uc); if (ret) return CMD_RET_FAILURE; uclass_foreach_dev(bus, uc) show_bus(bus); #else int i; |
3f4978c71 i2c: common chang... |
1833 1834 1835 |
for (i = 0; i < CONFIG_SYS_NUM_I2C_BUSES; i++) { printf("Bus %d:\t%s", i, I2C_ADAP_NR(i)->name); #ifndef CONFIG_SYS_I2C_DIRECT_BUS |
59aa9df38 dm: i2c: Implemen... |
1836 |
int j; |
3f4978c71 i2c: common chang... |
1837 1838 1839 1840 1841 1842 1843 |
for (j = 0; j < CONFIG_SYS_I2C_MAX_HOPS; j++) { if (i2c_bus[i].next_hop[j].chip == 0) break; printf("->%s@0x%2x:%d", i2c_bus[i].next_hop[j].mux.name, i2c_bus[i].next_hop[j].chip, i2c_bus[i].next_hop[j].channel); |
67b23a322 I2C: adding new "... |
1844 |
} |
3f4978c71 i2c: common chang... |
1845 1846 1847 |
#endif printf(" "); |
67b23a322 I2C: adding new "... |
1848 |
} |
59aa9df38 dm: i2c: Implemen... |
1849 |
#endif |
67b23a322 I2C: adding new "... |
1850 |
} else { |
59aa9df38 dm: i2c: Implemen... |
1851 |
int i; |
3f4978c71 i2c: common chang... |
1852 1853 |
/* show specific bus */ i = simple_strtoul(argv[1], NULL, 10); |
59aa9df38 dm: i2c: Implemen... |
1854 1855 1856 1857 1858 1859 1860 1861 1862 1863 1864 1865 |
#ifdef CONFIG_DM_I2C struct udevice *bus; int ret; ret = uclass_get_device_by_seq(UCLASS_I2C, i, &bus); if (ret) { printf("Invalid bus %d: err=%d ", i, ret); return CMD_RET_FAILURE; } show_bus(bus); #else |
3f4978c71 i2c: common chang... |
1866 1867 1868 1869 1870 1871 1872 |
if (i >= CONFIG_SYS_NUM_I2C_BUSES) { printf("Invalid bus %d ", i); return -1; } printf("Bus %d:\t%s", i, I2C_ADAP_NR(i)->name); #ifndef CONFIG_SYS_I2C_DIRECT_BUS |
59aa9df38 dm: i2c: Implemen... |
1873 |
int j; |
3f4978c71 i2c: common chang... |
1874 1875 1876 1877 1878 1879 1880 1881 1882 1883 1884 |
for (j = 0; j < CONFIG_SYS_I2C_MAX_HOPS; j++) { if (i2c_bus[i].next_hop[j].chip == 0) break; printf("->%s@0x%2x:%d", i2c_bus[i].next_hop[j].mux.name, i2c_bus[i].next_hop[j].chip, i2c_bus[i].next_hop[j].channel); } #endif printf(" "); |
59aa9df38 dm: i2c: Implemen... |
1885 |
#endif |
67b23a322 I2C: adding new "... |
1886 |
} |
3f4978c71 i2c: common chang... |
1887 1888 |
return 0; |
67b23a322 I2C: adding new "... |
1889 |
} |
3f4978c71 i2c: common chang... |
1890 |
#endif |
67b23a322 I2C: adding new "... |
1891 |
|
06afa388b i2c: kerneldoc: A... |
1892 1893 1894 1895 1896 1897 1898 1899 1900 1901 |
/** * do_i2c_bus_num() - Handle the "i2c dev" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. */ |
63656b762 dm: i2c: Implemen... |
1902 1903 |
#if defined(CONFIG_SYS_I2C) || defined(CONFIG_I2C_MULTI_BUS) || \ defined(CONFIG_DM_I2C) |
0e350f81e common: commands:... |
1904 1905 |
static int do_i2c_bus_num(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) |
bb99ad6d8 Add support for m... |
1906 |
{ |
3f4978c71 i2c: common chang... |
1907 |
int ret = 0; |
63656b762 dm: i2c: Implemen... |
1908 |
int bus_no; |
bb99ad6d8 Add support for m... |
1909 |
|
63656b762 dm: i2c: Implemen... |
1910 |
if (argc == 1) { |
e857a5bdb mpc83xx: Miscella... |
1911 |
/* querying current setting */ |
63656b762 dm: i2c: Implemen... |
1912 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 |
#ifdef CONFIG_DM_I2C struct udevice *bus; if (!i2c_get_cur_bus(&bus)) bus_no = bus->seq; else bus_no = -1; #else bus_no = i2c_get_bus_num(); #endif printf("Current bus is %d ", bus_no); } else { |
3f4978c71 i2c: common chang... |
1925 |
bus_no = simple_strtoul(argv[1], NULL, 10); |
880a41273 i2c: fix i2c dev ... |
1926 |
#if defined(CONFIG_SYS_I2C) |
3f4978c71 i2c: common chang... |
1927 1928 1929 1930 1931 |
if (bus_no >= CONFIG_SYS_NUM_I2C_BUSES) { printf("Invalid bus %d ", bus_no); return -1; } |
880a41273 i2c: fix i2c dev ... |
1932 |
#endif |
3f4978c71 i2c: common chang... |
1933 1934 |
printf("Setting bus to %d ", bus_no); |
f9a4c2da7 dm: i2c: Rename d... |
1935 1936 1937 |
#ifdef CONFIG_DM_I2C ret = cmd_i2c_set_bus_num(bus_no); #else |
3f4978c71 i2c: common chang... |
1938 |
ret = i2c_set_bus_num(bus_no); |
f9a4c2da7 dm: i2c: Rename d... |
1939 |
#endif |
e857a5bdb mpc83xx: Miscella... |
1940 |
if (ret) |
bb99ad6d8 Add support for m... |
1941 1942 |
printf("Failure changing bus number (%d) ", ret); |
bb99ad6d8 Add support for m... |
1943 |
} |
4fbd258e6 i2c: Correct comm... |
1944 1945 |
return ret ? CMD_RET_FAILURE : 0; |
bb99ad6d8 Add support for m... |
1946 |
} |
3f4978c71 i2c: common chang... |
1947 |
#endif /* defined(CONFIG_SYS_I2C) */ |
bb99ad6d8 Add support for m... |
1948 |
|
06afa388b i2c: kerneldoc: A... |
1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 |
/** * do_i2c_bus_speed() - Handle the "i2c speed" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. */ |
54841ab50 Make sure that ar... |
1959 |
static int do_i2c_bus_speed(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) |
bb99ad6d8 Add support for m... |
1960 1961 |
{ int speed, ret=0; |
63656b762 dm: i2c: Implemen... |
1962 1963 1964 1965 1966 1967 1968 1969 |
#ifdef CONFIG_DM_I2C struct udevice *bus; if (i2c_get_cur_bus(&bus)) return 1; #endif if (argc == 1) { #ifdef CONFIG_DM_I2C |
ca88b9b93 dm: i2c: Add a dm... |
1970 |
speed = dm_i2c_get_bus_speed(bus); |
63656b762 dm: i2c: Implemen... |
1971 1972 1973 |
#else speed = i2c_get_bus_speed(); #endif |
e857a5bdb mpc83xx: Miscella... |
1974 |
/* querying current speed */ |
63656b762 dm: i2c: Implemen... |
1975 1976 1977 |
printf("Current bus speed=%d ", speed); } else { |
bb99ad6d8 Add support for m... |
1978 1979 1980 |
speed = simple_strtoul(argv[1], NULL, 10); printf("Setting bus speed to %d Hz ", speed); |
63656b762 dm: i2c: Implemen... |
1981 |
#ifdef CONFIG_DM_I2C |
ca88b9b93 dm: i2c: Add a dm... |
1982 |
ret = dm_i2c_set_bus_speed(bus, speed); |
63656b762 dm: i2c: Implemen... |
1983 |
#else |
bb99ad6d8 Add support for m... |
1984 |
ret = i2c_set_bus_speed(speed); |
63656b762 dm: i2c: Implemen... |
1985 |
#endif |
e857a5bdb mpc83xx: Miscella... |
1986 |
if (ret) |
bb99ad6d8 Add support for m... |
1987 1988 |
printf("Failure changing bus speed (%d) ", ret); |
bb99ad6d8 Add support for m... |
1989 |
} |
4fbd258e6 i2c: Correct comm... |
1990 1991 |
return ret ? CMD_RET_FAILURE : 0; |
bb99ad6d8 Add support for m... |
1992 |
} |
06afa388b i2c: kerneldoc: A... |
1993 1994 1995 1996 1997 1998 1999 2000 2001 2002 |
/** * do_i2c_mm() - Handle the "i2c mm" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. */ |
54841ab50 Make sure that ar... |
2003 |
static int do_i2c_mm(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) |
bb99ad6d8 Add support for m... |
2004 |
{ |
bfc3b77eb cmd_i2c.c: rework... |
2005 2006 |
return mod_i2c_mem (cmdtp, 1, flag, argc, argv); } |
06afa388b i2c: kerneldoc: A... |
2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 |
/** * do_i2c_nm() - Handle the "i2c nm" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. */ |
54841ab50 Make sure that ar... |
2017 |
static int do_i2c_nm(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) |
bfc3b77eb cmd_i2c.c: rework... |
2018 2019 2020 |
{ return mod_i2c_mem (cmdtp, 0, flag, argc, argv); } |
e96ad5d3a cmd_i2c: Clean up... |
2021 |
|
06afa388b i2c: kerneldoc: A... |
2022 2023 2024 2025 2026 2027 2028 2029 2030 |
/** * do_i2c_reset() - Handle the "i2c reset" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero always. */ |
54841ab50 Make sure that ar... |
2031 |
static int do_i2c_reset(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) |
bfc3b77eb cmd_i2c.c: rework... |
2032 |
{ |
63656b762 dm: i2c: Implemen... |
2033 2034 2035 2036 2037 2038 2039 2040 2041 2042 2043 |
#if defined(CONFIG_DM_I2C) struct udevice *bus; if (i2c_get_cur_bus(&bus)) return CMD_RET_FAILURE; if (i2c_deblock(bus)) { printf("Error: Not supported by the driver "); return CMD_RET_FAILURE; } #elif defined(CONFIG_SYS_I2C) |
3f4978c71 i2c: common chang... |
2044 2045 |
i2c_init(I2C_ADAP->speed, I2C_ADAP->slaveaddr); #else |
bfc3b77eb cmd_i2c.c: rework... |
2046 |
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE); |
3f4978c71 i2c: common chang... |
2047 |
#endif |
bfc3b77eb cmd_i2c.c: rework... |
2048 2049 2050 2051 |
return 0; } static cmd_tbl_t cmd_i2c_sub[] = { |
59aa9df38 dm: i2c: Implemen... |
2052 |
#if defined(CONFIG_SYS_I2C) || defined(CONFIG_DM_I2C) |
3f4978c71 i2c: common chang... |
2053 |
U_BOOT_CMD_MKENT(bus, 1, 1, do_i2c_show_bus, "", ""), |
9a2accb44 i2c, multibus: ge... |
2054 |
#endif |
bfc3b77eb cmd_i2c.c: rework... |
2055 |
U_BOOT_CMD_MKENT(crc32, 3, 1, do_i2c_crc, "", ""), |
3f4978c71 i2c: common chang... |
2056 |
#if defined(CONFIG_SYS_I2C) || \ |
63656b762 dm: i2c: Implemen... |
2057 |
defined(CONFIG_I2C_MULTI_BUS) || defined(CONFIG_DM_I2C) |
bfc3b77eb cmd_i2c.c: rework... |
2058 |
U_BOOT_CMD_MKENT(dev, 1, 1, do_i2c_bus_num, "", ""), |
bb99ad6d8 Add support for m... |
2059 |
#endif /* CONFIG_I2C_MULTI_BUS */ |
735987c5a edid: Add I2C com... |
2060 2061 2062 |
#if defined(CONFIG_I2C_EDID) U_BOOT_CMD_MKENT(edid, 1, 1, do_edid, "", ""), #endif /* CONFIG_I2C_EDID */ |
bfc3b77eb cmd_i2c.c: rework... |
2063 2064 2065 2066 2067 2068 |
U_BOOT_CMD_MKENT(loop, 3, 1, do_i2c_loop, "", ""), U_BOOT_CMD_MKENT(md, 3, 1, do_i2c_md, "", ""), U_BOOT_CMD_MKENT(mm, 2, 1, do_i2c_mm, "", ""), U_BOOT_CMD_MKENT(mw, 3, 1, do_i2c_mw, "", ""), U_BOOT_CMD_MKENT(nm, 2, 1, do_i2c_nm, "", ""), U_BOOT_CMD_MKENT(probe, 0, 1, do_i2c_probe, "", ""), |
652e53546 cmd_i2c.c: added ... |
2069 |
U_BOOT_CMD_MKENT(read, 5, 1, do_i2c_read, "", ""), |
ed16f1468 cmd_i2c: Provide ... |
2070 |
U_BOOT_CMD_MKENT(write, 6, 0, do_i2c_write, "", ""), |
63656b762 dm: i2c: Implemen... |
2071 2072 |
#ifdef CONFIG_DM_I2C U_BOOT_CMD_MKENT(flags, 2, 1, do_i2c_flags, "", ""), |
c10c8e313 dm: i2c: Add a co... |
2073 |
U_BOOT_CMD_MKENT(olen, 2, 1, do_i2c_olen, "", ""), |
63656b762 dm: i2c: Implemen... |
2074 |
#endif |
bfc3b77eb cmd_i2c.c: rework... |
2075 |
U_BOOT_CMD_MKENT(reset, 0, 1, do_i2c_reset, "", ""), |
c76fe4742 common/cmd_[i-n]*... |
2076 |
#if defined(CONFIG_CMD_SDRAM) |
bfc3b77eb cmd_i2c.c: rework... |
2077 |
U_BOOT_CMD_MKENT(sdram, 1, 1, do_sdram, "", ""), |
902531788 common/: Remove l... |
2078 |
#endif |
bfc3b77eb cmd_i2c.c: rework... |
2079 2080 |
U_BOOT_CMD_MKENT(speed, 1, 1, do_i2c_bus_speed, "", ""), }; |
e4099c8b8 i2c: cmd: Relocat... |
2081 2082 2083 2084 2085 2086 2087 2088 |
static __maybe_unused void i2c_reloc(void) { static int relocated; if (!relocated) { fixup_cmdtable(cmd_i2c_sub, ARRAY_SIZE(cmd_i2c_sub)); relocated = 1; }; |
f1d2b313c ARM: add relocati... |
2089 |
} |
f1d2b313c ARM: add relocati... |
2090 |
|
06afa388b i2c: kerneldoc: A... |
2091 2092 2093 2094 2095 2096 2097 2098 2099 2100 |
/** * do_i2c() - Handle the "i2c" command-line command * @cmdtp: Command data struct pointer * @flag: Command flag * @argc: Command-line argument count * @argv: Array of command-line arguments * * Returns zero on success, CMD_RET_USAGE in case of misuse and negative * on error. */ |
54841ab50 Make sure that ar... |
2101 |
static int do_i2c(cmd_tbl_t * cmdtp, int flag, int argc, char * const argv[]) |
bfc3b77eb cmd_i2c.c: rework... |
2102 2103 |
{ cmd_tbl_t *c; |
e4099c8b8 i2c: cmd: Relocat... |
2104 2105 2106 |
#ifdef CONFIG_NEEDS_MANUAL_RELOC i2c_reloc(); #endif |
4444b221f i2c: fix command ... |
2107 |
if (argc < 2) |
4c12eeb8b Convert cmd_usage... |
2108 |
return CMD_RET_USAGE; |
4444b221f i2c: fix command ... |
2109 |
|
bfc3b77eb cmd_i2c.c: rework... |
2110 2111 2112 2113 2114 |
/* Strip off leading 'i2c' command argument */ argc--; argv++; c = find_cmd_tbl(argv[0], &cmd_i2c_sub[0], ARRAY_SIZE(cmd_i2c_sub)); |
47e26b1bf cmd_usage(): simp... |
2115 |
if (c) |
4c12eeb8b Convert cmd_usage... |
2116 |
return c->cmd(cmdtp, flag, argc, argv); |
47e26b1bf cmd_usage(): simp... |
2117 |
else |
4c12eeb8b Convert cmd_usage... |
2118 |
return CMD_RET_USAGE; |
bb99ad6d8 Add support for m... |
2119 |
} |
8bde7f776 * Code cleanup: |
2120 2121 |
/***************************************************/ |
088f1b199 common/cmd_*.c: s... |
2122 2123 |
#ifdef CONFIG_SYS_LONGHELP static char i2c_help_text[] = |
59aa9df38 dm: i2c: Implemen... |
2124 |
#if defined(CONFIG_SYS_I2C) || defined(CONFIG_DM_I2C) |
3f4978c71 i2c: common chang... |
2125 2126 |
"bus [muxtype:muxaddr:muxchannel] - show I2C bus info " |
9a2accb44 i2c, multibus: ge... |
2127 |
#endif |
fb0070e91 cmd_i2c.c: sorted... |
2128 2129 |
"crc32 chip address[.0, .1, .2] count - compute CRC32 checksum " |
3f4978c71 i2c: common chang... |
2130 |
#if defined(CONFIG_SYS_I2C) || \ |
63656b762 dm: i2c: Implemen... |
2131 |
defined(CONFIG_I2C_MULTI_BUS) || defined(CONFIG_DM_I2C) |
9bc2e4eee cmd_i2c: Fix help... |
2132 2133 |
"i2c dev [dev] - show or set current I2C bus " |
d9fc70324 [PATCH] I2C: disa... |
2134 |
#endif /* CONFIG_I2C_MULTI_BUS */ |
735987c5a edid: Add I2C com... |
2135 2136 2137 2138 |
#if defined(CONFIG_I2C_EDID) "i2c edid chip - print EDID configuration information " #endif /* CONFIG_I2C_EDID */ |
fb0070e91 cmd_i2c.c: sorted... |
2139 2140 |
"i2c loop chip address[.0, .1, .2] [# of objects] - looping read of device " |
d9fc70324 [PATCH] I2C: disa... |
2141 2142 2143 2144 2145 2146 2147 2148 |
"i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device " "i2c mm chip address[.0, .1, .2] - write to I2C device (auto-incrementing) " "i2c mw chip address[.0, .1, .2] value [count] - write to I2C device (fill) " "i2c nm chip address[.0, .1, .2] - write to I2C device (constant address) " |
54b99e51a i2c_probe: update... |
2149 2150 |
"i2c probe [address] - test for and show device(s) on the I2C bus " |
63656b762 dm: i2c: Implemen... |
2151 2152 |
"i2c read chip address[.0, .1, .2] length memaddress - read to memory " |
ed16f1468 cmd_i2c: Provide ... |
2153 2154 2155 2156 |
"i2c write memaddress chip address[.0, .1, .2] length [-s] - write memory " " to I2C; the -s option selects bulk write in a single transaction " |
63656b762 dm: i2c: Implemen... |
2157 2158 2159 |
#ifdef CONFIG_DM_I2C "i2c flags chip [flags] - set or get chip flags " |
c10c8e313 dm: i2c: Add a co... |
2160 2161 |
"i2c olen chip [offset_length] - set or get chip offset length " |
63656b762 dm: i2c: Implemen... |
2162 |
#endif |
e43a27c49 I2C: add new comm... |
2163 2164 |
"i2c reset - re-init the I2C Controller " |
c76fe4742 common/cmd_[i-n]*... |
2165 |
#if defined(CONFIG_CMD_SDRAM) |
fb0070e91 cmd_i2c.c: sorted... |
2166 2167 |
"i2c sdram chip - print SDRAM configuration information " |
902531788 common/: Remove l... |
2168 |
#endif |
088f1b199 common/cmd_*.c: s... |
2169 2170 2171 2172 |
"i2c speed [speed] - show or set I2C bus speed"; #endif U_BOOT_CMD( |
ed16f1468 cmd_i2c: Provide ... |
2173 |
i2c, 7, 1, do_i2c, |
088f1b199 common/cmd_*.c: s... |
2174 2175 |
"I2C sub-system", i2c_help_text |
d9fc70324 [PATCH] I2C: disa... |
2176 |
); |