Eric Lee / smarc-uboot

23 Jan, 2020

1 commit

21 Nov, 2019

2 commits

  • a09fea1d2   env: Finish migration of common ENV options ... Browse Code »
    1

    - In ARMv8 NXP Layerscape platforms we also need to make use of
    CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
    - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
    to 0.
    - Add Kconfig entry for ENV_ADDR.
    - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
    - Add ENV_xxx_REDUND options that depend on their primary option and
    SYS_REDUNDAND_ENVIRONMENT
    - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
    for the pre-main-U-Boot environment location.
    - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
    rather it being non-zero, as it will now be zero by default.
    - Rework the env_offset absolute in env/embedded.o to not use
    CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
    ENV_IS_IN_FLASH.
    - Migrate all platforms.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Cc: Patrick Delaunay
    Cc: uboot-stm32@st-md-mailman.stormreply.com
    Signed-off-by: Tom Rini
    Acked-by: Joe Hershberger
    Reviewed-by: Simon Goldschmidt

    Tom Rini
     
  • 8d8ee47e0   env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol ... Browse Code »
    24

    Today in initr_reloc_global_data() we use some non-obvious tests to
    determine if we need to relocate the env_addr within gd or not. In
    order to facilitate migration of other symbols to Kconfig we need to
    introduce a new symbol for this particular use case.

    Cc: Wolfgang Denk
    Cc: Joe Hershberger
    Signed-off-by: Tom Rini

    Tom Rini
     

24 Oct, 2019

1 commit

  • 3e6ab7327   usb: dwc3: Kconfig: get rid of obsolete mode selection ... Browse Code »

    The mode selection for the DWC3 is kind of obsolete. The driver does not
    have to be host only or gadget only. This choice is confusing.
    All the remaining callers of dwc3_uboot_init() explicitly set dr_mode
    before calling the function, so none rely on a default behavior.

    Remove the choice menu and keep only the USB_DWC3_GADGET option. Enable it
    by default if USB_GADGET and USB_DWC3 are enabled.
    It must be disabled for the evb-rk3328 as it uses DWC2 for the gadget and
    DWC3 for the host.

    Signed-off-by: Jean-Jacques Hiblot

    Jean-Jacques Hiblot
     

14 Aug, 2019

1 commit

31 Jul, 2019

1 commit

  • b160fac9f   board: amlogic: add support for Odroid-N2 ... Browse Code »

    ODROID-N2 is a single board computer manufactured by Hardkernel Co. Ltd
    with the following specifications:

    - Amlogic S922X ARM Cortex-A53 dual-core + Cortex-A73 quad-core SoC
    - 4GB DDR4 SDRAM
    - Gigabit Ethernet
    - HDMI 2.1 4K/60Hz display
    - 40-pin GPIO header
    - 4 x USB 3.0 Host, 1 x USB OTG
    - eMMC, microSD
    - Infrared receiver

    The board directory is W400, the name of the Amlogic Reference Design
    of Amlogic G12B with Gigabit boards, which will be used for similar
    boards.

    Signed-off-by: Neil Armstrong
    Tested-by: Mark Kettenis

    Neil Armstrong