20 Jan, 2018
40 commits
-
For preparation of adding AArch64 test.py jobs.
Signed-off-by: Tuomas Tynkkynen
Reviewed-by: Tom Rini -
It's mostly obvious, except that QEMU is annoying and requires an
explicit '-cpu cortex-a57' (or some other 64-bit core) to actually run
in 64-bit mode.While at it, remove the references to setting the ARCH environment
variable; that is not used in U-Boot.Signed-off-by: Tuomas Tynkkynen
Reviewed-by: Tom Rini -
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.Signed-off-by: Tuomas Tynkkynen
Reviewed-by: Tom Rini -
The signing certificate name is always 15 chars long, but need not be
null terminated. One solution is then to use printf precision modifiers
to only print this many chars ("%.15s"), but tiny printf does not support
this, so lets just drop printing the cert name for now.Signed-off-by: Andrew F. Davis
-
Fix the size calculation in the verify boot. The header size
should be subtracted from the image size, not be assigned to
the image size.Fixes: 0830d72bb9f8 ("arm: am33xx: security: adds auth support for encrypted images")
Signed-off-by: Madan Srinivas
Signed-off-by: Dan Murphy
Signed-off-by: Andrew F. Davis
Reviewed-by: Lokesh Vutla -
CONFIG_OF_EMBED in particular is needed to allow the Raspberry Pi
firmware to pass the DTB to U-Boot and on to the kernel.Signed-off-by: Drew Moseley
-
This commit adds UBIFS_NAND to BOOT_TARGET_DEVICES. This will
allow the kernel zImage to be loaded from '/boot/zImage' in UBIFS
(ubi0:rootfs).Additionally update the *_MMC devices to also load kernel image from
the MMC 0:2 EXT4 file system.DISTRO_DEFAULTS Setup
=====================
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:2 /boot/zImage and run mmcbootz
[fallback 2] Check MMC 0:2 /boot/uImage and run mmcboot
[fallback 3] Check NAND UBIFS /boot/zImage and run nandbootubifs
[fallback 4] Check NAND partitions and run nandbootThe following "extlinux.conf" can be used to load images in the
top-level of the MMC 0:1 FAT partition.[MMC(0:1)/extlinux/extlinux.conf]
---8 -
initr_mem() is already enclosed by
#if defined(CONFIG_PRAM)
#endifSo there is no need to check CONFIG_PRAM again inside the
function.Signed-off-by: Heinrich Schuchardt
Reviewed-by: Simon Glass -
The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.Cc: Dan Murphy
Signed-off-by: Tom Rini -
The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.Cc: Bin Meng
Cc: Simon Glass
Cc: Philipp Tomsich
Signed-off-by: Tom Rini
Reviewed-by: Simon Glass -
Change help description to match the style of the other U-Boot commands
and get rid of the leading whitespace.Signed-off-by: Klaus Goger
Reviewed-by: Lukasz Majewski -
The message "reading %s\n" may be interesting when
debugging but otherwise it is superfluous.Only output the message when debugging.
Signed-off-by: Heinrich Schuchardt
Reviewed-by: Simon Glass -
The message
"** %s shorter than offset + len **\n"
may be interesting when debugging but it does not indicate an
error.So we should not write it if we are not in debug mode.
Fixes: 7a3e70cfd88c fs/fs.c: read up to EOF when len would read past EOF
Signed-off-by: Heinrich Schuchardt
Reviewed-by: Simon Glass -
There is an #ifdef and #endif with nothing in between. This patch simply
removes this dead/useless code.Signed-off-by: Adam Ford
-
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 BeagleBoard(s). -
This commit adds OMAP3 BeagleBoard devicetree files from
Linux v4.15-rc5. This includes standard OMAP34XX board revisions as
well as the 'xM' which is OMAP36XX.Signed-off-by: Derald D. Woods
-
Select dtb name for am574x-idk and dra76x evm with acd package.
Signed-off-by: Lokesh Vutla
-
Add initial dts support for am574x-idk
Signed-off-by: Lokesh Vutla
-
Enable CMD_DDR3 on all am57xx based platforms.
Signed-off-by: Lokesh Vutla
-
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed ".Signed-off-by: Lokesh Vutla
-
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.Signed-off-by: Lokesh Vutla
Signed-off-by: Krunal Bhargav -
Update prcm, voltages and pinmux support for am574x-idk.
Signed-off-by: Lokesh Vutla
-
am574x-idk is a board based on TI's am574 processor
Add eeprom support.Signed-off-by: Lokesh Vutla
-
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPsBoth the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.Signed-off-by: Lokesh Vutla
-
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7 platforms.Signed-off-by: Lokesh Vutla
-
Move cmd_ddr3 to cmd/ti in order to make
it build for non-keystone TI platforms.Signed-off-by: Lokesh Vutla
[trini: Rename to ddr3.c not cmd_ddr3.c]
Signed-off-by: Tom Rini -
For data integrity, the EMIF1 supports ECC on the data
written or read from the SDRAM. Add support for enabling
ECC support in EMIF1.Signed-off-by: Lokesh Vutla
Signed-off-by: Krunal Bhargav -
This is a slight difference in emif_ddr_phy_status register offsets for
DRA7xx EMIF and older versions. And ecc registers are available only
in DRA7xx EMIC. Add support for this difference and ecc registers.Signed-off-by: Lokesh Vutla
-
Add support for simple memory fill operation. With large data sizes
it is much faster to use EDMA for memory fill rather than CPU.Signed-off-by: Tero Kristo
-
I'm working on a v2 patch to add support for a board named pdu001. Its
Linux DTS file uses the include file added by this patch. To keep Linux
and U-Boot DTS files in sync U-Boot requires a copy of this file,
although there is no driver for NXP's PCA9532 i2c LED driver chip (yet).Signed-off-by: Felix Brack
-
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.Signed-off-by: Lokesh Vutla
Reviewed-by: Tom Rini -
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.Signed-off-by: Tomi Valkeinen
-
DPLL DRR doesn't have an M4 divider. But the clock driver is trying
to configure M4 divider as 4(writing into a reserved register).
Fixing it by making M4 divider as -1.Reported-by: Steve Kipisz
Signed-off-by: Lokesh Vutla -
The size field in GP header that is expected by ROM is size of the
image + size of the header. But omapimage tool is updating size
as image size + 2 * header size. Remove this extra header size bytes.Reported-by: Denys Dmytriyenko
Debugged-by: Madan Srinivas
Signed-off-by: Lokesh Vutla -
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang
Signed-off-by: Lokesh Vutla -
Now that we have multi dtb enabled in u-boot allocate
128K space for u-boot.Signed-off-by: Lokesh Vutla
-
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.Reviewed-by: Lokesh Vutla
Signed-off-by: Vignesh R
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr
Signed-off-by: Lokesh Vutla
Signed-off-by: Faiz Abbas -
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I
Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini -
Instead of sending STOP TRANSMISSION command from MMC core, enable
the auto command feature so that the Host Controller issues CMD12
automatically when last block transfer is completed.Signed-off-by: Kishon Vijay Abraham I
Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini -
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.Signed-off-by: Kishon Vijay Abraham I
Signed-off-by: Jean-Jacques Hiblot
Reviewed-by: Tom Rini
