Eric Lee / smarc-uboot

08 Feb, 2019

1 commit

19 Jan, 2019

1 commit

  • 29d280c88   sunxi: usb: Switch to Generic host controllers ... Browse Code »

    Onc of key blocker for using USB Generic host controller
    drivers in Allwinner are CLK and RESET drivers, now these
    available for USB usage.

    So switch sunxi USB use EHCI and OHCI Generic controllers.

    Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
    where it already have USB_EHCI_HCD

    Signed-off-by: Jagan Teki
    Acked-by: Maxime Ripard

    Jagan Teki
     

04 Sep, 2018

1 commit

17 Aug, 2018

1 commit

  • 86cf1c828   configs: Migrate CONFIG_NR_DRAM_BANKS ... Browse Code »
    13

    We have the following cases:
    - CONFIG_NR_DRAM_BANKS was defined, migrate normally
    - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
    CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
    - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
    2), set this to 8.

    Signed-off-by: Tom Rini

    Tom Rini
     

17 Apr, 2018

1 commit

  • 4f67b93fb   part: Disable CONFIG_SPL_ISO_PARTITION by default ... Browse Code »

    We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
    could load distro images that usually get shipped as iso images. These images
    usually come with a board agnostic boot environment.

    However, there is very little point in having ISO support enabled (for anyone
    really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
    is board specific. So the fact that we enable ISO support in U-Boot proper does
    not mean at all that we want ISO support in U-Boot SPL.

    Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
    all those default configs that disabled SPL ISO support.

    Signed-off-by: Alexander Graf

    Alexander Graf
     

08 Apr, 2018

1 commit

14 Mar, 2018

1 commit

  • 341c05865   sunxi: move CONFIG_SYS_TEXT_BASE out of defconfigs ... Browse Code »

    Commit 278b90ce786f ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
    CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
    of moving the common definition shared by almost every sunxi board
    into 123 individual defconfig files. But the U-Boot start address
    for Allwinner boards is a platform decision which has been around for
    ages, so defining it in each *board* config file seems a bit over the
    top.
    Define the standard values (160MB into DRAM for most SoCs, with two
    SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
    the individual defconfigs.

    Signed-off-by: Andre Przywara
    Acked-by: Maxime Ripard
    Reviewed-by: Jagan Teki

    Andre Przywara
     

11 Feb, 2018

2 commits

06 Feb, 2018

1 commit

  • a4fa81146   cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA ... Browse Code »

    cmd/Makefile has:

    ifdef CONFIG_FPGA
    obj-$(CONFIG_CMD_FPGA) += fpga.o
    endif

    which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
    does nothing. Let's remove that Makefile conditional and instead express
    this equivalent dependency in Kconfig, so a lot of redundant

    # CONFIG_CMD_FPGA is not set

    can be removed from board defconfigs that don't actually have an FPGA.

    Signed-off-by: Tuomas Tynkkynen

    Tuomas Tynkkynen
     

21 Nov, 2017

1 commit

  • 6130b1f6b   sun50i: h5: Add NanoPi Neo Plus2 DT initial support ... Browse Code »

    Add initial DT for NanoPi NEO Plus2 by FriendlyARM
    - Allwinner quad core H5 Cortex A53 with an ARM Mali-450MP GPU
    - 1 GB DDR3 RAM
    - 8GB eMMC flash (Samsung KLM8G1WEPD-B031)
    - micro SD card slot
    - Gigabit Ethernet (external RTL8211E-VB-CG chip)
    - 802.11 b/g/n WiFi, Bluetooth 4.0 (Ampak AP6212A module)
    - 2x USB 2.0 host ports

    Signed-off-by: Antony Antony
    Reviewed-by: Jagan Teki

    Antony Antony