26 Mar, 2020
2 commits
-
Currently the following error message is seen during boot:
U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000
ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc@30110000: 0
Loading Environment from MMC... OK
In: serial@10210000
Out: serial@10210000
Err: serial@10210000
Model: Elgin RV1108 R1 board
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
....Since the elgin-rv1108 does not use ADC to read the download
key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid
such error.Signed-off-by: Otavio Salvador
Reviewed-by: Kever Yang -
Since commit 8e9a8d0d0c8c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.Signed-off-by: Otavio Salvador
Signed-off-by: Fabio Berton
Reviewed-by: Kever Yang
23 Jan, 2020
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
05 Dec, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
24 Nov, 2019
1 commit
-
- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
23 Nov, 2019
2 commits
-
Gadget vendor number, 0x2207 is common across all platfroms
supported in Rockchip SoC.So, select the same number globally, if ARCH_ROCKCHIP.
This eventually drop the explicit configs defined in supported
board defconfig files.Tested-by: Levin Du
Signed-off-by: Jagan Teki
Reviewed-by: Kever Yang -
Select the gadget manufacturer as 'Rockchip' for
all rockchip platform SoC's.This eventually drop the explicit defined added
on supported board defconfig files.Tested-by: Levin Du
Signed-off-by: Jagan Teki
Reviewed-by: Kever Yang
21 Nov, 2019
2 commits
-
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.Cc: Wolfgang Denk
Cc: Joe Hershberger
Cc: Patrick Delaunay
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini
Acked-by: Joe Hershberger
Reviewed-by: Simon Goldschmidt -
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not. In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.Cc: Wolfgang Denk
Cc: Joe Hershberger
Signed-off-by: Tom Rini
23 Sep, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
30 Apr, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
08 Jan, 2019
1 commit
-
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini
16 Dec, 2018
1 commit
-
Add the initial support for Elgin R1 board, which is based on the
RV1108 SoC and has the following features currently supported in
U-Boot:- UART
- eMMC
- USBSigned-off-by: Otavio Salvador
Reviewed-by: Philipp Tomsich